A large-sized rechargeable battery pack for your Raspberry Pi (or Arduino, or Propeller, or anything else that uses 5V!). This pack is intended for providing a lot of power to an GPS, cell phone, tablet, etc but we found it does a really good job of powering other miniature computers and micro-controllers. If you want something a little smaller, we have a 4400mAh power pack with one USB port that can provide up to 1A We tested it with an iPad...

A smaller-sized rechargeable battery pack for your Raspberry Pi or Raspberry Pi B+ (or Arduino, or Propeller, or anything else that works with 5V!). This pack is intended for providing power to an iPhone, cell phone, tablet, etc but we found it does a really good job of powering other miniature computers and micro-controllers. If you want more power we have a 4400mAh version  and if you want even more...

A medium-sized rechargeable battery pack for your Raspberry Pi (or Arduino, or Propeller, or anything else that uses 5V!). This pack is intended for providing a lot of power to an iPhone, cell phone, tablet, etc but we found it does a really good job of powering other miniature computers and micro-controllers. If you want even more power, we have a 10,000mAh power pack with two USB ports that can provide up to 2A! We tested it with an iPhone 5...

There's two standard ways to power electronics - USB or 5.5mm/2.1mm DC barrel jack. This or that! With this USB to 2.1mm Male Barrel Jack Cable , you can now power 5V DC powered electronics that have a DC jack from a USB jack with a handy 1 meter long cable. Simply plug the USB A side to any computer, PowerBoost, USB wall adapter, or even a USB battery pack. Other side is center positive, 5.5mm outer/2.1mm inner diameter jack. We got these...

BlinkyTape is a very special LED strip, taking the smarts of NeoPixels and combining it with an Arduino-compatible for an all-in-one ready to go design. You don’t have to source your own microcontroller, power supply or connectors. Simply plug in a standard USB battery pack or wall charger, and you’re good to blink. BlinkyTape has 60 independently controllable full-color RGB LEDs, all wrapped up in a weather-resistant silicone case....

Would you like to learn electronics, with an all-in-one board that has sensors and LEDs built in? Circuit Playground is here - and it's the best way to practice programming on real hardware with no soldering or sewing required! This is the Classic version of Circuit Playground , which comes with an ATmega32u4. It's designed to be used with Arduino IDE and code.org CS Discoveries only. It even comes with Firmata already programmed in, so...

At the time of its invention Morse code definitively changed the way we communicate. Historically it's been used in nautical navigation to aviation to radio, but its easy to learn and the universal nature makes it a great data entry method for folks who use Assistive Technology! GBoard is an alternate keyboard for Android devices that lets you type using Morse code. It then converts those dots and dashes into letters and...

The Code.org CS Discoveries course is a yearlong curriculum for teaching computer science, and there's even a physical computing unit! For large classrooms and workshops, we recommend our Code.org Classroom pack. But, if you need to supplement your Classroom pack or are learning on your own, we now have a mini-kit - with just the essentials for a single student or share-pair. Individual kit includes everything you need: 1 x Circuit...

Circuit Playground Express is the next step towards a perfect introduction to electronics and programming. We've taken the original Circuit Playground Classic and made it even better! Not only did we pack even more sensors in, we also made it even easier to program. Start your journey with Microsoft MakeCode block-based or Javascript programming. Then, you can use the same board to try CircuitPython , with the Python interpreter running...

Circuit Playground Express  is the next step towards a perfect introduction to electronics and programming. We've taken the original Circuit Playground Classic and made it even better! Not only did we pack even more sensors in, we also made it even easier to program. You can now start your journey with  Microsoft MakeCode  block-based or Javascript programming. If you're in a classroom following Code.org's CS...

Add a power switch to any USB-powered project simply by plugging this between the USB power port and the USB cable. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a USB A socket on one end and a USB A plug on the other. In between is an in-line switch that is rated for 2 Amps. The data lines are not connected through - this is a ground/5V power switch only! The...

This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 12V powered devices with a center-positive 2.1mm DC barrel jack from a USB port. We also have a version that provides 9V, and if you just need a passthough cable, here's one for 5VDC. These are rated at 500mA output, but you...

This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 9V powered devices with a center-positive 2.1mm DC barrel jack from a USB port. We also have a version that provides 12V, and if you just need a passthough cable, here's one for 5VDC. These are rated at 500mA output, but you...

Add some extra boom to your audio project with these powered loudspeakers. We sampled half a dozen different models to find ones with a good frequency response, so you'll get quality audio output for music playback. Simply connect the standard 3.5mm stereo plug into your Raspberry Pi model B or B+, Wave shield, etc. There's even a volume control wheel on it so you can set it up just right. For power, plug the USB connector into anything...

Convert just about any battery pack to 5V with VERTER - our fresh new Buck-Boost power converter. VERTER can take battery voltages from 3-12VDC and output a nice 5V DC, which makes it a perfect universal power supply for your portable project! Where Verter really shines is when you have a battery or power range that can fluctuate a lot, or you don't know what you'll end up using. It operates smoothly over the 3-12V range, moving from a...

The world's first and only open-source hardware charger: The MintyBoost®! New version! Works with the new iPhone 4 & 5 and more! Please review the Minty Boost project page(s) before purchase and assembly!, some phones require different modifications to the kit to charge properly! Some phones such as the *iPhone 3gs are very sensitive to charging via USB and may not work in all environments or configurations. Make your own...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming UNTIL...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming UNTIL...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be very small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any...

For many years, instructors and teachers have asked us to come up with a better way to teach programming and electronics. We have worked on Circuit Playground Express for over a year to come up with a board that is powerful, beautiful, fun, and perfect for teaching Code.org CS Discoveries Circuit Playground Express  is a perfect introduction to electronics and programming. It combines a poweful ATSAMD21G18 microcontroller with full Code.org...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be very small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming...

The British Invasion is here! No, not music... microcontrollers! The BBC micro:bit is one of the newest and easiest ways to learn programming and electronics. Designed specifically for kids and beginners, the  micro:bit  is a pocket-sized computer that you can code, customize and control to bring your digital ideas, games and apps to life. It’s a small, code-able device that is a non-intimidating introduction to programming and...

Sense the world around you! The FLORA Sensor Pack includes many types of sensors for your wearable enjoyment. Sense motion, direction, color, light levels, touch, and connections with FLORA sensor breakouts and conductive materials, and a few NeoPixels for experimenting with displaying your sensor information. Take your project portable with the included battery pack and stitch it into a final design with conductive thread. $100 worth of goodies...

FLORA is Adafruit's fully-featured wearable electronics platform. It's a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects.FLORA comes with Adafruit's support, tutorials and projects. Check out dozens of FLORA tutorials on the Adafruit Learning System, with more added all the time! The FLORA is small (1.75" diameter, weighing 4.4 grams). The FLORA family also has the best stainless...

This is the  Adafruit Feather M0 RFM69 Packet Radio (868 or 915 MHz) . We call these RadioFruits , our take on an microcontroller with a RFM69HCW packet radio transceiver plus built in USB and battery charging. Its an Adafruit Feather M0 with a 900MHz radio module cooked in! Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for...

This is the  Adafruit Feather 32u4 Radio (RFM69HCW)   900MHz . We call these RadioFruits , our take on an microcontroller packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather 32u4 with a 900 MHz radio module cooked in! Great for making wireless networks that can go further than 2.4GHz 802.15.4 and similar, are more flexible than Bluetooth LE and without the high power requirements of WiFi. Feather is...

This is the  Adafruit Feather M0 RFM69 Packet Radio (433 MHz) . We call these RadioFruits , our take on an microcontroller with a RFM69 HCW packet radio transceiver plus built in USB and battery charging. Its an Adafruit Feather M0 with a 433MHz radio module cooked in! Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable...

In collaboration with Google and Mongoose OS, Adafruit's releasing an IoT Core Pack based around our Feather HUZZAH32! This kit includes a pre-soldered  Adafruit Feather HUZZAH with ESP32 WiFi and some sensors and components to get you started on your IoT journey. Feather is a development board from Adafruit that, like its namesake, is thin, light and lets you fly.  We designed Feather to be a new standard for portable...

This is the  Adafruit Feather 32u4 Radio (RFM69HCW)   433MHz . We call these RadioFruits , our take on an microcontroller packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather 32u4 with a 433 MHz radio module cooked in! Great for making wireless networks that can go further than 2.4GHz 802.15.4 and similar, are more flexible than Bluetooth LE and without the high power requirements of WiFi. We...

In collaboration with Microsoft and Hackster.io, Adafruit's releasing a Virtual IoT pack with boards, sensors, and quite a number of components! This kit is specifically curated for IoT Virtual Bootcamp hosted by Microsoft and Hackster.io in partnership with Adafruit. This kit includes a pre-soldered  Adafruit Feather HUZZAH with ESP8266 WiFi and some sensors and components to get you started on your IoT journey.  ...

Ahoy! It's time to create a dazzling light up project with our new RGB Matrix FeatherWing . Now you can quickly and easily create projects featuring your favorite 16 or 32-pixel tall matrix boards. Using our RGB Matrix library is easy and works wonderfully with any of our M0 or M4 based Feathers. Please note: This wing is only tested/designed to work with the SAMD21 M0 and SAMD51 M4 Feathers. It's not for use with any other Feathers at...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the  Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module, ready to rock! We...

This is the Adafruit Feather M0 RFM95 LoRa Radio (900MHz) . We call these RadioFruits , our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather M0 with a 900MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without the high power requirements of WiFi. Feather is the new development board...

This is the  Adafruit Feather 32u4 LoRa Radio (RFM9x) . We call these RadioFruits , our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather 32u4 with a 868/915 MHz radio module cooked in! Great for making wireless networks that can go further than 2.4GHz 802.15.4 and similar, are more flexible than Bluetooth LE and without the high...

This is the Adafruit Feather M0 RFM96 LoRa Radio (433 MHz). We call these RadioFruits , our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather M0 with a 433MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without the high power requirements of WiFi. Feather is the new development board...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the  Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module, ready to rock! We...

This is the  Adafruit Feather 32u4 LoRa Radio (RFM9x) . We call these RadioFruits , our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather 32u4 with a 433 radio module cooked in! Great for making wireless networks that can go further than 2.4GHz 802.15.4 and similar, are more flexible than Bluetooth LE and without the high power...

Aww yeah, it's the Feather you have been waiting for! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather family, check'em out here. That module...

If you have an ItsyBitsy or Pro Trinket you probably know it's the perfect little size for a portable project. This LiPoly backpack makes it really easy to do! Instead of wiring 2 or 3 boards together to make a charging system, this little PCB sits on top of the PCB and allows a LiPoly/LiIon battery to plug in. When the Pro Trinket or ItsyBitsy USB port is powered, the battery is recharged automatically. Unplug the USB port and the...

Aww yeah, it's the Feather you have been waiting for, and now with stacking headers ! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather family,...

Aww yeah, it's the Feather you have been waiting for, this time with pre-assembled headers ! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather...

Aww yeah, it's the Feather you have been waiting for! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather family, check'em out here. That module...

OK you've signed up for Adafruit.io and you're ready to build something cool and Internet-connected. All you need is this starter kit which will get you going with lots of parts that go very well with our service and are the most common sensors and actuators you may want. Sense light, motion, humidity, temperature, and more, then send it for storage on adafruit.io! Light up LEDs, make noise, and move a motor when a trigger is detected....

The Adafruit Feather nRF52 Pro is another Bluetooth Low Energy board for advanced projects and users who want to use a fully open source Bluetooth Low Energy 5.0 stack . It has a native-Bluetooth chip, the nRF52832, as well as built in USB Serial and battery charging!  We have other boards in the Feather family, check'em out here. This is a special Feather - unlike the rest of the Feather family, this board is not...

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield goes onto your Arduino and provides a slim rechargeable power pack, with a built in battery charger as well as DC/DC booster. Compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due - basically any Arduino-pinout-shaped Arduino as only the GND and 5V pins are used. You can stack shields...

As electronics get smaller and smaller, you'll need a hand examining PCBs and this little USB microscope is the perfect tool. Its smaller and lighter than a large optical microscope but packs quite a bit of power in its little body. There's a high quality 640x480 camera sensor inside and an optical magnifier that can adjust from 5x (for basic PCB inspection) to 200x (for detailed inspection). Eight mini white LEDs are angled right onto...

Go interactive with sensors and Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic sensing project (or two). There's a GEMMA board, four sewable bright RGB pixels, a motion sensor, a switch, a light sensor, a piezo, a rechargeable battery and charger, 2-ply conductive thread, alligator clips to help you test out your circuit, and a USB cable for programming GEMMA. Gemma Sensor Pack contents: Adafruit...

We still love the Pro Trinket but the bit-bang USB technique it uses doesn't work as well as it did in 2014. So while we still carry the Pro Trinket, we really recommend using the Metro Mini (ATmega328 @ 5V 16 MHz), ItsyBitsy 32u4 5V 16MHz, ItsyBitsy 32u4 @ 3.3V 8MHz or ItsyBitsy M0 @ 3V 48MHz. All have built-in USB and are comparable in price! The ItsyBitsy's especially are about the same size and have native USB and tons of pins, so...

Love FLORA but want a bite-sized version? Look no further, GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by a Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project! We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Perfect for when you don't want to...

What's smaller than a Feather but larger than a Trinket? It's an Adafruit ItsyBitsy M0 Express ! Small, powerful, with a rockin' ATSAMD21 Cortex M0 processor running at 48 MHz - this microcontroller board is perfect when you want something very compact, but still with a bunch of pins. ItsyBitsy M0 Express is only 1.4" long by 0.7" wide, but has 6 power pins, 23 digital GPIO pins (12 of which can be analog in, 1x analog out,...

What's smaller than a Feather but larger than a Trinket? It's an ItsyBitsy! Small, powerful, Arduino-compatible - this microcontroller board is perfect when you want something very compact, but still with a bunch of pins. ItsyBitsy is only 1.4" long by 0.7" wide, but has 6 power pins, 6 analog & digital pins and 17 digital pins. It packs much of the same capability as an Arduino UNO. So it's great once you've...

We still love the Pro Trinket but the bit-bang USB technique it uses doesn't work as well as it did in 2014. So while we still carry the Pro Trinket, we really recommend using the Metro Mini (ATmega328 @ 5V 16 MHz), ItsyBitsy 32u4 5V 16MHz, ItsyBitsy 32u4 @ 3.3V 8MHz or ItsyBitsy M0 @ 3V 48MHz. All have built-in USB and are comparable in price! The ItsyBitsy's especially are about the same size and have native USB and tons of pins, so...

What's smaller than a Feather but larger than a Trinket? It's an Itsy Bitsy! Small, powerful, Arduino-compatible - this microcontroller board is perfect when you want something very compact, but still with a bunch of pins. Itsy Bitsy is only 1.4" long by 0.7" wide, but has 6 power pins, 6 analog & digital pins and 17 digital pins. It packs much of the same capability as an Arduino UNO or Feather 32u4. So it's great once...

For all those who feared their Game Boy days would be but a memory, worry no more! The Game Boy may be dead, but with this pack you'll have a chance to revive it in style. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME, NES, Atari2600 and other fine emulators (via RetroPie/EmulationStation) It's called the Pocket PiGRRL and it's...

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3xAAA battery holder and batteries, a battery extension cable, our high quality stainless steel thread, alligator clips to help you test out your parts...

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a USB cable for programming GEMMA. Note : As of June 20th, 2016 this pack no longer comes with CR2032 batteries to make shipping easier for customers. You...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery, we also have a 1200mAh model The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a...

Get started with the fabulous Adafruit Flora platform with this lovely starter kit. Included are plenty of parts to make a few different fun projects! There's a Flora motherboard, a GPS module that can also perform location datalogging, eight ultra-bright chainable RGB pixels, a battery holder and batteries, two types of our high quality stainless steel thread, alligator clips to help you test out your parts, a USB cable for reprogramming the...

PowerBoost is the perfect power supply for your portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. Like our popular 5V 1A USB wall adapter, we tweaked the output to be 5.2V instead of a straight-up 5.0V so that there's a little bit of 'headroom' long cables, high draw, the addition of a diode on the output if you wish, etc. The 5.2V...

PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. With a beefy 4A DC/DC converter, it can give you 1A+ from as low as 2V.  Like our popular 5V 1A USB wall adapter, we tweaked the output to be 5.2V instead of a straight-up 5.0V so that there's a little bit of...

For all those who feared their Game Boy days would be but a memory, worry no more! The Game Boy may be dead, but with this pack you'll have a chance to revive it. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME and NES emulators. This is version 2.0! We've updated this project for the Raspberry Pi 2 or 3 with more buttons (D-Pad,...

As of October 12th, 2015 this product now ships with an Adafruit Trinket with a micro-USB plug. One of the most popular Trinket projects now has its own kit pack!  Make your very own programmable NeoPixel goggles with 2 x 16 LED rings and an Adafruit Trinket. It even comes with a rechargeable LiPoly battery and charger. It's a great easy build and when you're done you'll have the coolest accessory. Follow along with our popular...

Mod your stuffed toy to chirp, meow, or woof! This GEMMA parts pack makes it easy to add simple sounds to any plush toy, and especially the Sew-Your-Own Owl Kit (not included!) A tilt ball switch is used to trigger GEMMA to play a sound of your choosing (or write your own) through a small speaker, amplified by a transistor. This product includes: 1x Adafruit Gemma V21x 3.7v 150mAh LiPoly Battery 1x Tilt Ball Switch1x Adafruit Micro...

PowerBoost 1000C is the perfect power supply for your portable project!  With a built-in load-sharing battery charger circuit, you'll be able to keep your power-hungry project running even while recharging the battery!  This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects. If you dont need the 1A battery charger, smart...

PowerBoost 500C is the perfect power supply for your portable project! With a built-in battery charger circuit, you'll be able to keep your project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects. If you need a 1A battery charger, smart load-sharing, and 1A iOS resistors, check out the...

Add a good quality, slim chiclet keyboard as well as an optical mouse to your Raspberry Pi, Beagle Bone Black or other mini-computer with this wireless combo set. Best of all, it only uses a single USB port! This combo comes with a sleek black chiclet keyboard and and mouse both controlled by a single wireless USB dongle. The keyboard is a full QWERTY keyboard and is compatible with all operating systems. The mouse is comfortable for all hand...

Pickup a copy of Getting Started with Adafruit FLORA and then hit the ground running with everything that you need to become an Adafruit FLORA supreme being! This pack is perfect for somebody interested in the wide world of wearable electronics and Adafruit's tiny FLORA board.  Pack includes: 1x Getting Started with Adafruit FLORA book 1x FLORA - Wearable electronic platform: Arduino-compatible As of May 12th, 2015 the FLORA...

Pickup a copy of Getting Started with Adafruit Trinket and then hit the ground running with one of the most popular Trinket projects: the Trinket-Powered NeoPixel Goggle Kit Pack! This pack is perfect for somebody who is up for a little challenge and eager to dive further into the wonderful world of Adafruit Trinket. This pack includes the Getting Started book and the entire Goggle Kit Pack: Getting Started with Adafruit Trinket6"...

Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete over 20 different circuit and projects. Basically everything you need to be playing within minutes of its arrival. No soldering required, works with Mac, Windows and Linux! This item is the same exact kit as https://www.adafruit.com/product/170 This pack includes the Adafruit Metro. METRO is the...

Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete over 20 different circuit and projects. Basically everything you need to be playing within minutes of its arrival. No soldering required, works with Mac, Windows and Linux! New! As of March 28, 2018 we've done a big refresh on this kit, to add more stuff like a character LCD, Infrared remote and...

For all those who feared their Game Boy playing days would be but a memory, worry no more! That handheld may be dead, but with this pack you'll have a chance to revive it. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME and NES emulators. This version DOES NOT INCLUDE THE RASPBERRY PI ZERO W! It is also a DIY kit that requires you to...

For all those who feared their Game Boy playing days would be but a memory, worry no more! That handheld may be dead, but with this pack you'll have a chance to revive it. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME and NES emulators. This version includes the Raspberry Pi Zero W! However, it is a DIY kit that requires you to 3D print...

AdaBox007 – SPY is the perfect gift for folks who are just getting started in the world of DIY electronics. It's an excellent addition to our family of DIY projects, plus it's a solderless pack. This is also a great way to test the waters of AdaBox before committing to a subscription. Please note! This is NOT the subscription version of AdaBox! This is  ONLY  AdaBox007 that shipped out to AdaBox subscribers...

At first glance, the Pi Zero isn't much.  It just looks like a slimmed down version of the Raspberry Pi we know and love.  But when we started to think of the possibilities - and what a well-chosen set of accessories could add - we realized the appeal.  And then we saw the price...could it be true? Yes! This is the slimmest, most pared down Raspberry Pi to date.  It's kind of like the little cousin to the Pi 2 -...

This is the version that comes with a FREE Ting 2G Sim Card! Please note if you need to use a 3G network you will need to use an AT&T 3G SIM card as the Ting SIM is 2G only. For those who want to take it to the next level we now have a 3G Cellular Modem breakout! The FONA 3G has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset tracking. This all-in-one cellular phone...

Cellular + GPS tracking, all in one? Oh yes! Introducing Adafruit FONA 808 MiniGSM + GPS, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in an adorable little package. (It does not contain a drum machine, tho) This module measures only 1.75"x1.6" but packs a surprising amount of technology into it's little frame. At the heart is a powerful GSM cellular module...

For those who want to take it to the next level we now have a 3G Cellular Modem breakout! The FONA 3G has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset tracking. This all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in a single breakout. If you want the version that comes with a free Ting 2G SIM Card,...

For those who want to take it to the next level we now have a 3G Cellular Modem breakout! The FONA 3G has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset tracking. This all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in a single breakout. This module measure only 1.75"x1.6" but packs a surprising...

Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75"x1.25" but packs a surprising amount of technology into its little frame. At the heart is a GSM cellular module (we use the latest SIM800) the size of a postage stamp....

Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75"x1.25" but packs a surprising amount of technology into its little frame. At the heart is a GSM cellular module (we use the latest SIM800) the size of a postage stamp....

Need an easy-to-use but powerful control solution for more industrial-type projects? Get the controller that does exactly what you want in a sturdy, contained package. Combine Arduino simplicity, ESP8266 WiFi connectivity, and Digital Logger's experience and reliability to customize your own PLC for controlling industrial and robotics projects.  Digital Loggers PLDuino is a PLC (Programmable Logic Controller) that is based on the...

Try the JavaScript of things with the Espruino WiFi - the world's first open-source JavaScript microcontroller, this time with built in WiFi! This little board has an STM32 microcontroller pre-programmed with Espruino all ready to go so you can start playing with Javascript-microcontrollers. It also comes with an ESP8266 WiFi module, so you can connect to the Internet using Espruino. Warning: if you only use Assembly and think that even...

Control Electronics quickly and easily with a tiny USB stick that runs JavaScript - introducing the Espruino Pico ! Dig in to the JavaScript of things, with a mini version of the popular Espruino board we already carry This little board has an STM32 microcontroller pre-programmed with Espruino all ready to go so you can start playing immediately. Warning: if you only use Assembly and think that even embedded C/C++ is for wimps, this device might...

You don't need an electrical engineering degree to start hacking electronics! This intuitive guide shows how to wire, disassemble, tweak, and re-purpose everyday devices quickly and easily. Packed with full-color illustrations, photos, and diagrams, Hacking Electronics teaches by doing--each topic features fun, easy-to-follow projects. Discover how to hack sensors, accelerometers, remote controllers, ultrasonic rangefinders, motors, stereo...

Try the JavaScript of things with the Espruino - the world's first open-source JavaScript microcontroller! This little board has an STM32 microcontroller pre-programmed with Espruino all ready to go so you can start playing with Javascript-microcontrollers. Warning: if you only use Assembly and think that even embedded C/C++ is for wimps, this device might explody your head. The Espruino is a tiny computer with a JavaScript interpreter,...

Evil Mad Scientist Labs never disappoints with their fantastic kits and clocks. The Alpha Clock Five is no exception: An awesome alarm clock soldering kit-- featuring five crazy-bright, crazy huge 2.3" alphanumeric LED displays in dazzling white, a Chronodot RTC (for precise quartz timing, complete with battery backup) and a handsome laser-cut acrylic case. These big 18-segment alphanumeric LED displays are notoriously difficult to drive--...

Evil Mad Scientist Labs never disappoints with their fantastic kits and clocks. The Alpha Clock Five is no exception: An awesome alarm clock soldering kit-- featuring five crazy-bright, crazy huge 2.3" alphanumeric LED displays in red, a Chronodot RTC (for precise quartz timing, complete with battery backup) and a handsome laser-cut acrylic case. These big 18-segment alphanumeric LED displays are notoriously difficult to drive-- there are...

For those who want to take it to  the next level  we now have a 3G Cellular Modem breakout! The FONA 3G has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset tracking. This all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in a single breakout. This module measure only 1.75"x1.6" but packs a...

This cute pocket oscilloscope is a perfect companion to your tool box. For beginners, its a good starter scope - it is not as complicated as a benchtop scope so its easy to use. For advanced EE's, its useful as a scope-on-the-go, for field-debugging, when you don't want to drag your scope over, or when a floating-ground is needed (it will naturally do 'differential' measurements as long as its not plugged into a computer USB...

The Adafruit Feather nRF52 Bluefruit is another easy-to-use all-in-one Bluetooth Low Energy board, with a native-Bluetooth chip, the nRF52832!  It's our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. We have other boards in the Feather family, check'em out here. This chip has twice the flash, SRAM and performance of the earlier nRF51-based Bluefruit modules. Best of...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the  Adafruit Feather 32u4 Bluefruit  - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather 32u4 with a BTLE module, ready to rock! We have other...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the  Adafruit Feather M0 Bluefruit LE  - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. It's an Adafruit Feather M0 with a BTLE module, ready to rock! We have...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the  Adafruit Feather 32u4 Bluefruit with Headers - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather 32u4 with a BTLE module, ready to rock! We have...

This is the  Adafruit Feather 32u4 Bluefruit  - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. It's an Adafruit Feather 32u4 with a BTLE module, ready to rock! Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. We have...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the  Adafruit Feather 32u4 Bluefruit  - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather 32u4 with a BTLE module, ready to rock! We have other...

The British Invasion is here! No, not music...microcontrollers! New to the USA is the newest and easiest way to learn programming and electronics - the BBC micro:bit . Designed specifically for kids and beginners, the  micro:bit  is a pocket-sized computer that you can code, customize and control to bring your digital ideas, games and apps to life. It’s a small, code-able device that is a non-intimidating introduction to...

The British Invasion is here! No, not music...microcontrollers! New to the USA is the newest and easiest way to learn programming and electronics - the BBC micro:bit . Designed specifically for kids and beginners, the  micro:bit  is a pocket-sized computer that you can code, customize and control to bring your digital ideas, games and apps to life. It’s a small, code-able device that is a non-intimidating introduction to...

NOTE: This product is only designed for use with solar panels sold at the Adafruit store. We cannot guarantee this will work with solar panels purchased elsewhere. Please purchase this kit and panels from Adafruit to ensure optimized functionality! A 2.1mm adapter cable is also required to adapt a solar panel to the DC power jack. Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This...