This RF adapter cable is super handy for anyone doing RF work. Often times, small electronics save space by having a pick-and-placeable u.FL connector (also called uFL, IPEX, IPAX, IPX, MHF, and AM). But most antennas have SMA or RP-SMA connectors on them. This little cable will bridge the two! This cable is RG178 and is 15cm (5.9") long not including the SMA...

This is a great connector for anyone doing RF work, when a straight SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground. Mates with any SMA plug. Check if you have RP-SMA or SMA by looking at the middle pin...

This RF adapter cable is super handy for anyone doing RF work. Often times, small electronics save space by having a pick-and-placeable u.FL connector (also called uFL, IPEX, IPAX, IPX, MHF, and AM). But most antennas have SMA or RP-SMA connectors on them. This little cable will bridge the two! This cable is RG178 and is 15cm (5.9") long not including the RP-SMA...

This is a great connector for anyone doing RF work, when an SMA connector is required. It hugs the edge of a standard 0.063" thick PCB and 'launches' off of the edge. We like these for their ease of soldering and low profile. Mates with any SMA plug, we also have an SMA to RP-SMA in case your antenna is RP-SMA You can find an Eagle footprint for this part in the...

This is a great connector for anyone doing RF work, when a right angle SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground. Mates with any SMA plug. Check if you have RP-SMA or SMA by looking at the middle...

This is a great connector for anyone doing RF work, when an SMA connector is required. It hugs the edge of a "half thickness" 0.031" thick PCB (or thinner!) and 'launches' off of the edge. We like these for their ease of soldering and low profile. Mates with any SMA plug, we also have an SMA to RP-SMA in case your antenna is RP-SMA You can find an Eagle footprint for...

uFL connectors are very small surface-mount parts used when an external RF antena is desired but a big bulky SMA connector takes up too much space. We use this part on our GPS and WiFi boards, they're great! Chances are your antenna doesn't use uFL as the main connector, in which case you should check out our uFL to SMA and uFL to RP-SMA adapter cables. These are...

This is a great connector for anyone doing RF work, when a right angle RP-SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground. Mates with any RP-SMA plug. Check if you have RP-SMA or SMA by looking at the...

This RF adapter bit is great for anyone doing RF work. If your receiver/transmitter/transceiver has an MCX connector but you really want to tie it to an SMA antenna, this dongle will do the trick!

This 2.4"/61mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Antenna comes with a SMA connector, which is the most common type you'll see for Cellular development boards. If you need to connect this to an RP-SMA...

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Antenna comes with a Right-angle SMA connector. If you need to connect this to an RP-SMA connector for some reason, use this handy adapter and if you need...

If you're building a Raspberry Pi project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most cases. However, WiFi does not have a long range and also requires both investment (through your ISP) and setup (routers, access points, network security schemes). If you're deploying your project somewhere more remotely,...

If you're building a IoT project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most cases. But, what if you find WiFi does not have a long range you need? If you're deploying your project somewhere more remotely, without WiFi or a strong cellular network, like a rural area, you'll need another option. Something that...

The RockBLOCK 9603 allows you to send and receive short messages from anywhere on Earth with a clear view of the sky. And when we say anywhere we mean anywhere. It works far beyond the reach of WiFi and GSM networks. Maybe you want to transmit weather information from mid-ocean? Or use it to control your robot in the middle of the desert? Perhaps you need emergency...

This RF adapter bit is great for anyone doing RF work. Depending on the dev-board and antenna you have, you may be faced with either RP-SMA or SMA connectors. Unfortunately they are not compatible! This adapter solves the problem with an SMA jack on one end and an RP-SMA Plug on the other. We also have the opposite 'flavor' available Check your cable, connector and...

Most antennas have SMA or RP-SMA connectors on them, how are you going to connect them to your little RF module? This little cable will bridge the two! This adapter cable is super handy for anyone doing RF work with modules that have w.FL connectors. It has a tiny MHF3/ IPEX3 / wFL / w.FL connector on the end - not a uFL connector - on one end, and an RP-SMA plug on...

This RF adapter bit is great for anyone doing RF work. Depending on the dev-board and antenna you have, you may be faced with either RP-SMA or SMA connectors. Unfortunately they are not compatible! This adapter solves the problem with a RP-SMA jack on one end and an SMA Plug on the other. We also have the opposite 'flavor' available Check your cable, connector and...