After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely of 316L stainless steel. Once you start working with this thread you'll quickly agree its optimal for any wearables work! This thread is 2 ply, a little thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles or with a sewing machine that...

After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely of 316L stainless steel. Once you start working with this thread you'll quickly agree its optimal for any wearables work! This thread is 3 ply, thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles. This may be sew-able by a sewing...

This 316L stainless steel thread falls somewhere between a thick thread and a thin yarn. Most sewing machines wouldn't be happy with this thread since its thick, and it has the 'furry' soft feel of yarn which makes it poor for most e-textiles/wearables projects. However, the high conductivity and softness make it a great thread for making iPhone gloves! Sew a couple inches into the pad of your gloves to keep your hands toasty while...

FLORA is Adafruit's fully-featured wearable electronics platform. It's a round, sewable, Arduino-compatible microcontroller designed to empower amazing wearables projects.FLORA comes with Adafruit's support, tutorials and projects. Check out dozens of FLORA tutorials on the Adafruit Learning System, with more added all the time! The FLORA is small (1.75" diameter, weighing 4.4 grams). The FLORA family also has the best stainless...

The Adafruit Gemma M0 is a super small microcontroller board, with just enough built-in to create many simple projects. It may look small and cute: round, about the size of a quarter, with friendly alligator-clip sew pads. But do not be fooled! The Gemma M0 is incredibly powerful! We've taken the same form factor we used for the original ATtiny85-based Gemma and gave it an upgrade. The Gemma M0 has swapped out the lightweight...

Push once to turn on, push again to turn off, push again to turn the other side on, one last push and it's off again! It's basically a push-button toggle switch that connects and disconnects. This clicky Mini On/Off Button switch makes a great power switch or mode toggler. They're often referred to as 'flashlight' switches because you see them used in small flashlights. Can reliably handle up to 500mA and up to 12VDC. This is...

Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our conductive thread and wearable electronics parts. Each pack contains 20 gold-eye sharps, with eye sizes ranging from #3 (1.75" long) to #9 (1.35" long). The two #3's (the largest) are too large to pass through the sewable coin cell holder but otherwise are easy to use and thread. The four #9's...

Circuit Playground Express  is the next step towards a perfect introduction to electronics and programming. We've taken the original Circuit Playground Classic and made it even better! Not only did we pack even more sensors in, we also made it even easier to program. You can now start your journey with  Microsoft MakeCode  block-based or Javascript programming. If you're in a classroom following Code.org's CS...

The small 5mm size of these tin-plated brass snaps means they fit perfectly on Flora's pads! Snaps make a great connector for wearables-- solder one side to the board and sew the other to your project with conductive thread! This card comes with 24 complete snaps (socket and stud pairs). Some discoloration may occur during soldering. These snaps are washable, oxidation-resistant, and nonmagnetic.

Add motion and direction sensing to your wearable FLORA project with this high precision 3-axis Accelerometer+Compass sensor. Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space. The other is a magnetometer that can sense where the strongest magnetic force is coming from, generally used to detect...

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3xAAA battery holder and batteries, a battery extension cable, our high quality stainless steel thread, alligator clips to help you test out your parts...

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a USB cable for programming GEMMA. Note : As of June 20th, 2016 this pack no longer comes with CR2032 batteries to make shipping easier for customers. You...

This kit is designed for use with the electronic textiles unit in the Exploring Computer Science (ECS, http://www.exploringcs.org/e-textiles) introductory computing curriculum for secondary students. It contains most of the materials needed for four e-textiles projects: paper circuit, wristband, mural, and human sensor project. The curricular unit is designed to take students new to computing and sewing through a series of projects where...

Add LED accents to textile projects with Adafruit's LED Sewing Kit! Stitch a glowing circuit with conductive thread-- this kit comes with everything you need to get started: 1 bobbin of 2-ply conductive thread2 x sewable CR2032 battery holders4 x candle flicker LEDs - they twinkle automatically, no need for a microcontroller or external circuit!4 x 5mm snaps to use as as sewable switchesNeedle set Note: As of September 30th, 2015, this...

This kit is designed for use with the electronic textiles unit in the Exploring Computer Science (ECS, http://www.exploringcs.org/e-textiles) introductory computing curriculum for secondary students. It contains most of the materials needed for four e-textiles projects: paper circuit, wristband, mural, and human sensor project. The curricular unit is designed to take students new to computing and sewing through a series of projects where...

This product's about as simple as a cup of lemonade on a hot summer day.  And, like lemonade, it's just three components! This board is a sewable adapter with a 3-pin JST wiring adapter.  It's a perfect way to add a simple link between things like our Flora NeoPixels and more complicated products like our NeoPixel Rings.  There are three holes on the board that are perfect for conductive thread (or soldering if...

Pickup a copy of Getting Started with Adafruit FLORA and then hit the ground running with everything that you need to become an Adafruit FLORA supreme being! This pack is perfect for somebody interested in the wide world of wearable electronics and Adafruit's tiny FLORA board.  Pack includes: 1x Getting Started with Adafruit FLORA book 1x FLORA - Wearable electronic platform: Arduino-compatible As of May 12th, 2015 the FLORA...

This woven conductive ribbon is great for powering lots of LEDs in a wearable project. It's thin, strong, smooth, and made completely of 316L stainless steel. It plays nice with our stainless conductive thread and is very flexible, just like textile ribbon. The easiest way to attach this ribbon is to either slip it through a casing, or better yet, zig-zag stitch over it to tack it down. Because it is strong and flexible, its ideal for any...

Get started with the fabulous Adafruit Flora platform with this lovely starter kit. Included are plenty of parts to make a few different fun projects! There's a Flora motherboard, a GPS module that can also perform location datalogging, eight ultra-bright chainable RGB pixels, a battery holder and batteries, two types of our high quality stainless steel thread, alligator clips to help you test out your parts, a USB cable for reprogramming the...

Make your wearables glow with the GEMMA sequin pack ! This GEMMA parts pack makes it easy to add light to your wearables. It comes with thread, needles, a holder for 2 x CR2032 coin cell batteries, a GEMMA sewable microcontroller, and warm white Adafruit LED Sequins. This pack is perfect for adding a little sparkle to any garment or accessory, and is a great way to get started sewing electronics. Note : As of June 20th, 2016 this pack no longer...

This woven conductive ribbon is great for powering lots of LEDs in a wearable project. It's thin, strong, smooth, and made completely of 316L stainless steel. It plays nice with our stainless conductive thread and is very flexible, just like textile ribbon. The easiest way to attach this ribbon is to either slip it through a casing, or better yet, zig-zag stitch over it to tack it down. Because it is strong and flexible, its ideal for any...

These sewable badges are  unbearrrrrably cute. Bearables is Pimoroni's range of woodland-themed wearable LED badges and sensors. String 'em with conductive thread to bring this DIY-meets-Disney badge to life! This Bearables Fox Kit features twelve colored LEDs (blue, green, yellow, orange, red, pink) with twelve different light patterns. The multi-functional button on the badge sets the light pattern, the sensor's...

Go interactive with sensors and Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic sensing project (or two). There's a GEMMA board, four sewable bright RGB pixels, a motion sensor, a switch, a light sensor, a piezo, a rechargeable battery and charger, 2-ply conductive thread, alligator clips to help you test out your circuit, and a USB cable for programming GEMMA. Gemma Sensor Pack contents: Adafruit...

These sewable badges are  unbearrrrrably cute. Bearables is Pimoroni's range of woodland-themed wearable LED badges and sensors. String 'em with conductive thread to bring this DIY-meets-Disney badge to life! This Bearables Bear Kit features twelve colored LEDs (blue, green, yellow, orange, red, pink) with twelve different light patterns! The multi-functional button on the badge sets the light pattern, the sensor's...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 1.5 meters long, and has 20 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 21"/53cm long, and has 10 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

Yes, this is an adorable small HDMI television with incredibly high resolution and built in 3W stereo speakers ! We tried to get the smallest possible HDMI/VGA display with high-res, high-contrast visibility. The visible display measures only 7" (17.8cm) diagonal, and the TFT comes in an enclosure with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect a 9 to 12VDC adapter to the 2.1mm center-positive DC jack (not...

This lightweight, flexible fabric ribbon cable contains four channels of conductive thread, perfect for wiring up wearables where flexibility is key. Use it to connect your conductive fabric gamepad to your microcontroller or computer! Features: Low resistance: ~16 Ω / ft. [304.80 mm]4 Conductor connectionsPower and data applicationsLight-weightSewableWashable and dryableStitchable over apparel construction seamsFoldable onto itself...

This lightweight, flexible fabric ribbon cable contains four channels of conductive thread, perfect for wiring up wearables where flexibility is key. Use it to connect your conductive fabric gamepad to your microcontroller or computer! Features: Low resistance: ~16 Ω / ft. [304.80 mm]4 Conductor connectionsPower and data applicationsLight-weightSewableWashable and dryableStitchable over apparel construction seamsFoldable onto itself...

Add light-reactive sensing to your wearable Flora project with this high precision Lux sensor. The TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from up to 0.1 - 40,000+ Lux on the fly. The best part of...

Sense the world around you! The FLORA Sensor Pack includes many types of sensors for your wearable enjoyment. Sense motion, direction, color, light levels, touch, and connections with FLORA sensor breakouts and conductive materials, and a few NeoPixels for experimenting with displaying your sensor information. Take your project portable with the included battery pack and stitch it into a final design with conductive thread. $100 worth of goodies...

Add motion, direction and orientation sensing to your wearable FLORA project with this high precision 9-DOF sensors. Inside are three sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space. The other is a 3-axis magnetometer that can sense where the strongest magnetic force is coming from, generally used...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 21"/53cm long, and has 10 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 1.5 meters long, and has 30 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...