Pump up the volume with this 20W stereo amplifier! This slim little board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Power it with 5-12VDC using the onboard DC power jack and plug stereo line level into the 3.5mm stereo headphone jack and jam out with ease. Since it's class D, its completely cool-running, no heat sinks are required and it's extremely efficient - up to 93%...

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 2.1W channels into 4 ohm impedance speakers (@ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when driving an 8Ω speaker at 1.5 Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current...

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving an 8Ω speaker at over a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection...

A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is able to deliver 2 x 2.8W channels into 4 ohm impedance speakers (@ 10% THD) and it has a i2c control interface as well as an AGC (automatic gain control) system to keep your audio from clipping or distorting. If you don't want to use I2C to control it, it does start up on with 6dB gain by default and the AGC set up for...

This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we...

Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly as noisy or scratchy as other mic amp breakouts...

Listen to this good news - we now have a breakout board for a super tiny MEMS microphone. Just like 'classic' electret microphones, MEMS mics can detect sound and convert it to voltage, but they don't need a bias resistor or amplifier, its all in one! The SPW2430 is a small, low cost MEMS mic with a range of 100Hz - 10KHz, good for just about all general audio recording/detection. This breakout is best used for projects such as...

Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in a robot rebellion. Why even go down that path? Here at Adafruit, we believe in making robots our  friends! So if you find yourself wanting a companion, consider the robot. They're fun to program, and you can get creative with decorations. With that in mind, we designed Crickit - That's our C...

The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. We looked at hundreds of prop builds, and thought about what would make for a great low-cost (but well-designed) add-on for our...

The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. This version of the FeatherWing has plain headers soldered in, so it's easy to plug into our Feathers. We looked at hundreds...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and...

Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in a robot rebellion. Why even go down that path? Here at Adafruit, we believe in making robots our  friends! So if you find yourself wanting a companion, consider the robot. They're fun to program, and you can get creative with decorations. With that in mind, we designed the Adafruit Crickit HAT -...

Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in a robot rebellion. Why even go down that path? Here at Adafruit, we believe in making robots our  friends! So if you find yourself wanting a companion, consider the robot. They're fun to program, and you can get creative with decorations. With that in mind, we designed  Crickit  -...

If you have a circuit board or a project you want enclosed, but need something extra durable, this extruded box is absolutely perfect.  It's made from solid anodized aluminum so it's still lightweight while being durable, it's also easy to machine or drill. The end-plates come off and you could cut out a custom end plate from another material if you like. The inside has circuit board slots so if you have a custom PCB, it can...

Yes, this is an adorable small HDMI television with incredibly high resolution and built in 3W stereo speakers ! We tried to get the smallest possible HDMI/VGA display with high-res, high-contrast visibility. The visible display measures only 7" (17.8cm) diagonal, and the TFT comes in an enclosure with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect a 9 to 12VDC adapter to the 2.1mm center-positive DC jack (not...

If you have a circuit board or a project you want enclosed, but need something extra durable, this extruded box is absolutely perfect.  It's made from solid anodized aluminum so it's still lightweight while being durable, it's also easy to machine or drill. The end-plates come off and you could cut out a custom end plate from another material if you like. The inside has circuit board slots so if you have a custom PCB, it can...

The Prop Shield with Motion Sensors for Teensy 3.2 and Teensy-LC is meant for making interactive light and sound effects on small handheld props and wearable costumes! Good for all sorts of projects, and designed by the creator of the Teensy so you know it's gonna be well supported Motion Sensors  - Allows motion interactive light & sound. Audio Amplifier  - Clear quality audio output to a small speaker. Fast LED Driver...

The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. We have these with and without headers already soldered in We looked at hundreds of prop builds, and thought about what would make...

Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in a robot rebellion. Why even go down that path? Here at Adafruit, we believe in making robots our  friends! So if you find yourself wanting a companion, consider the robot. They're fun to program, and you can get creative with decorations. With that in mind, we designed Crickit - That's our C...

For all those who feared their Game Boy days would be but a memory, worry no more! The Game Boy may be dead, but with this pack you'll have a chance to revive it. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME and NES emulators. This is version 2.0! We've updated this project for the Raspberry Pi 2 or 3 with more buttons (D-Pad,...

For all those who feared their Game Boy days would be but a memory, worry no more! The Game Boy may be dead, but with this pack you'll have a chance to revive it in style. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME, NES, Atari2600 and other fine emulators (via RetroPie/EmulationStation) It's called the Pocket PiGRRL and it's...

Power-up your TV with a Pimoroni Picade Console Controller ! It's a compact, Raspberry Pi-powered retro games machine with authentic arcade controls that plugs right into your TV, monitor, or other HDMI display. It's a stylish, retro, and fun arcade controller for your Raspberry Pi! Picade Console is fight stick-style arcade console that riffs off the Pimoroni Picade with the same retro feel, same joystick and buttons, dedicated power...

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT . It's the best, easiest way to make a super-sweet arcade system using any Raspberry Pi. Simply pop it onto your Pi,  plug your Pi power supply into the micro-USB connector on the Picade HAT  (it back-powers your Pi through the GPIO, so no need for a separate power supply), wire up your controls to the terminal...

Our pirate friends at Pimoroni have taken the I2S mono DAC and amplifier that they used on Speaker pHAT and Picade HAT and added a second one for stereo goodness. pHAT BEAT gives you high-quality, digital, amplified, stereo audio and 16 beautiful little RGB LEDs, in two rows of 8, that are ideal as a VU meter, and 6 buttons to control your audio. There's a nifty little DIP switch on the bottom of the...

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little pHAT. It's the neatest way to add audio to your Pi project, and its beautiful artwork evokes an 80s boombox! Pimoroni isn't claiming audiophile sound quality, but it's perfect for fun little projects where you want to add sound output – speech, notification sounds, or light...

*HONK* *HONK* micro:bit comin' thru! Maybe you've played with the micropython speech module, or maybe you want to have MakeCode sound effects. Well, we couldn't let the other boards have all the audio fun! Now you can make your micro:bit BLURP and BEEP with noise:bit ! Just slide noise:bit into the micro:bit board and start MakeCoding to your maker heart's content. Generate sound bites, tones, etc, with the...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming UNTIL...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be very small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be very small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any...

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret microphones in situations where the loudness of the audio isn't predictable. This fancy microphone amplifier module is a step above the rest, with built...

Add some easy-listenin' tunes to your Raspberry Pi using this basic audio bonnet. It'll give you stereo line out from a digital I2S converter for a good price, and sounds nice to boot! This bonnet features the UDA1334A I2S Stereo DAC, a perfect match for any I2S-output audio interface. It's affordable but sounds great - music to our ears. It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi...

Listen to this good news - we now have an all in one digital audio amp breakout board that works incredibly well with the Raspberry Pi! If you're looking for an easy and low cost way to get your digital sound files bumpin' then the MAX98357 I2S Amp Breakout is for you. It takes standard I2S digital audio input and, not only decodes it into analog, but also amplifies it directly into a speaker. Perfect for adding compact...

Listen up! This tiny 1" diameter speaker cone is the perfect addition to any small audio project where you need an 8 Ω impedance and will be using 0.5W or less of power. We particularly like this cone as it's very simple and its metal body is extremely lightweight. It's very similar to the speaker in the Drawdio kit. Works great with our Wave shield or class D amplifier board. Just be careful not to overdrive it if you're...

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 4 ohm impedance and 3W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our class D amplifier board. Speaker - 3" Diameter - 4 Ohm 3 Watt (0:01)

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value). We particularly like this cone as it's very simple and its plastic body is extremely lightweight and thin. Originally designed for 'talking' greeting...

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our Wave shield or class D amplifier board. Speaker - 3" Diameter - 8 Ohm 1 Watt (0:01)

We got a big ol' blender and tossed in an ItsyBitsy M4, two NeoTrellis boards and an electret mic amp - turned on the 'mix' button and out came the NeoTrellis M4 - a super fun dev board for anyone who likes to squish buttons, see pretty lights and maybe make a tune or two. The NeoTrellis M4 is an all-in-one USB + NeoPixel + Elastomer + Audio board. It's powered by our new favoritest-chip-in-the-world, the SAMD51, a Cortex M4 core...

Hey Mr. DJ! Turn up that Raspberry Pi mix to the  max  with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi . (It's not big enough to be an official HAT, so we called it a bonnet, you see?) It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi computers with a 2x20 connector - A+, B+, Zero, Pi 2, Pi 3, etc. We've tested it out with Raspbian (the official operating system) and...

So you've got a cool/witty name for your band, a Soundcloud account, a 3D-printed Daft Punk helmet... so what could be missing from your road to stardom? The NeoTrellis M4 Kit Pack , of course! The NeoTrellis M4 is an all-in-one USB + NeoPixel + Elastomer + Audio board. It's powered by our new favoritest-chip-in-the-world, the SAMD51, a Cortex M4 core running at 120 MHz. This chip has a speedy core with CircuitPython and...

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and volume digitally. There is also 8 GPIO pins that can be used for stuff...

Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers you've seen. Instead, a metal rod is wrapped with the voice coil. When current is pulsed through the coil, the magnetic field causes a piece of metal to expand and contract - and if it's pressed against a surface it turns the transducer into a speaker! Often these size transducers are pressed up...

Listen up! This 1.1" (~30mm) diameter speaker is the perfect addition to any breadboard-based audio project where you need 8 Ohm impedance, and have 0.2W or less of power. The two pins are 15mm / 0.6" apart and fit perfectly in a breadboard or perfboard. This speaker has a durable protective plastic casing that's still lightweight. Works great with our Wave shield or class D amplifier board (just be careful not to overdrive it)

Bend all audio files to your will with the Adafruit Music Maker FeatherWing + Amplifier ! It's a fun-size version of our Music Maker shield for Arduino, and similar to our other Music Maker FeatherWing, but this one is even better - with an on-board 3 Watt amplifier ! This powerful wing features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI,...

When you need to amplify, filter, add, or otherwise manipulate analog signals you'll certainly want an operational amplifier at your side. This is our favorite hobby op-amp, which we use in our kits! It's DIP package so very easy to work with on a breadboard or perfboard. It has two amplifiers inside. It can run from voltages as low as 2.7V and up to 6V. It has rail to rail input and output, which is a common problem for beginners who...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and...

Listen up! This high power 4" diameter speaker will amp up any audio project where you need loud sound! It is 4 ohm impedance, rated for 20W continuous power. (This thing is really loud) It also has four handy mounting tabs 3 inches apart, and a grill that fits on top. The grill is to protect the cones, and is not necessary for use. This speaker has a nice wide range of 60Hz - 24kHz, which is pretty good for a speaker this large. Originally...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal.  The Pi Zero Stereo W Bonnet Pack  sets you up with the WiFi-enabled Pi Zero W, and our I2S 3W Stereo Speaker Bonnet. This bonnet uses digital sound standard...

One truth about working with audio is you always need the cable or adapter you  don't  have in your toolbox. That's why we love these terminal-block audio connectors so much.  No soldering required!  Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 1/4" (6.35mm) Stereo Plug Terminal Block . It's a pretty common size and is super useful for more heavy duty...

Build your very own internet-connected radio with Pimoroni's  Pirate Radio Kit! This kit has just-about-everything you'll need: Pimoroni's flashy new pHAT BEAT DAC and stereo amp, a 5W speaker, and a beautifully retro acrylic enclosure to make it look the business. It even includes a Pi Zero W. All you need is to  add your own micro-SD card and USB power supply. It'll take you around 30...

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires with a connector on the end. It has a handy "Molex PicoBlade" 1.25mm pitch 2-pin cable, which makes plugging into a board easy. Or you can cut off the connector and just solder/clamp onto...

Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm spacing). This...

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. The pair have a handy SPK input cable to add audio to your displays (the connectors are similar to the JST-PH series which is ~2.0mm spacing). We're specifically carrying...

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires with a connector on the end. It has a handy "Molex PicoBlade" 1.25mm pitch 2-pin cable, which makes plugging into a board easy. Or you can cut off the connector and just solder/clamp onto...

The Pimoroni Picade Cabinet is a stylish, retro, and fun arcade cabinet for your Raspberry Pi! The Picade Cabinet comes in kit form for you to build at home. All parts, panels, and components are included - you just need to supply the Raspberry Pi and power adapter. We highly recommend using a Raspberry Pi 3 B+ as the extra processing power gives great performance in many emulators. This is the desktop arcade cabinet version of the...

Playing retro games is easy on a Raspberry Pi - and that pocket-sized computer is pretty good at it too! All you need is a little help to connect buttons and a joystick up and you can custom design your own arcade console, desktop or stand-up machine, even just a simple controller box. It makes for a fun weekend project that will last all year. This Adafruit Arcade Bonnet is designed to make small emulator projects a little easier to build....

Aww yeah, it's the Feather you have been waiting for! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather family, check'em out here. That module...

Aww yeah, it's the Feather you have been waiting for, this time with pre-assembled headers ! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather...

Aww yeah, it's the Feather you have been waiting for, and now with stacking headers ! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather family,...

Squeeeeze down your next ESP32 project to its bare-bones essential with the Adafruit HUZZAH32 Breakout . This breakout is basically the 'big sister' of our HUZZAH 8266, but instead of an ESP8266 it has the '32! We've pared down our popular Feather ESP32, removing the battery charger and USB-serial converter. You just get a regulator, some protection diodes, two buttons and an LED. For some projects, where price and size are at a...

Aww yeah, it's the Feather you have been waiting for! The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. We packed everything you love about Feathers: built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings. We have other boards in the Feather family, check'em out here. That module...

Some of us just can't make up our minds: just deciding what to have for dinner is a major decision process. We want it all! And now we can have it all, with this python-powered internet-of-things powerhouse. It's like getting to have pizza AND sushi AND tacos AND casserole AND a burger for dinner, wow! Imagine five networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython...

If you loved Make:Electronics then you'll really love the sequel, Make: More Electronics. Make More electronics is another book from Charles Platt full of more ways to learn about electronics in fun, hands-on ways. It's a great next step after the original Make:Electronics and expands on many of the things you've already learned or mastered from the first book. Immediately, Make:More Electronics picks up where Make: Electronics left...

You don't need an electrical engineering degree to start hacking electronics! This intuitive guide shows how to wire, disassemble, tweak, and re-purpose everyday devices quickly and easily. Packed with full-color illustrations, photos, and diagrams, Hacking Electronics teaches by doing--each topic features fun, easy-to-follow projects. Discover how to hack sensors, accelerometers, remote controllers, ultrasonic rangefinders, motors, stereo...

This low-cost Prop Shield  for Teensy 3.2 and Teensy-LC is meant for making light and sound effects on small handheld props and wearable costumes! Good for all sorts of projects, and designed by the creator of the Teensy so you know it's gonna be well supported Audio Amplifier  - Clear quality audio output to a small speaker. Fast LED Driver  - Drive APA102 / Dotstar LEDs for colorful lighting with rapid response. Flash...

Unleash the audio capabilities of your Raspberry Pi! The Cirrus Logic Audio Card , produced by Element14 in collaboration with Cirrus Logic, offers Raspberry Pi® users similar flexibility to a PC sound-card to capture audio alongside their camera, and experiment with stereo digital capture and playback. The Cirrus Logic audio board adds a powerful class D amplifier to the Raspberry Pi. The audio board adds inputs for SPDIF, Line in and...

THE ELECTRONICS KNOW-HOW YOU NEED TO BECOME A SUCCESSFUL INVENTOR "If there is a successor to Make: Electronics, then I believe it would have to be Practical Electronics for Inventors ....perfect for an electrical engineering student or maybe a high school student with a strong aptitude for electronics....I’ve been anxiously awaiting this update, and it was well worth the wait."--GeekDad (Wired.com) Advance your electronics...

Gameduino 2 is a shield that adds a bright 4.3 inch touchscreen, an embedded GPU, headphone jack, accelerometer and microSD slot to your Arduino - or anything else with an SPI interface. Everything you need to create compelling games – right in your hand. Sound output is via an amplified headphone jack. The system supports a selection of built-in samples and instruments, and can also play samples from video memory, at up to 48KHz. The...

Want to know how to use an electronic component? The Encyclopedia of Electronic Components Vol. 3 by Charles Platt and Fredrik Jansson includes key information on electronics parts for your projects--complete with photographs, schematics, and diagrams. You'll learn what each one does, how it works, why it's useful, and what variants exist. No matter how much you know about electronics, you'll find fascinating details...

Want to know how to use an electronic component? The Encyclopedia of Electronic Components Vol. 2 by Charles Platt includes key information on electronics parts for your projects--complete with photographs, schematics, and diagrams. You'll learn what each one does, how it works, why it's useful, and what variants exist. No matter how much you know about electronics, you'll find fascinating details you've never come across...