Adafruit Parts Pal
-
Description
Description-
LEDs and passives and transistors and switches and op-amps oh my! The Adafruit Parts Pal is the ultimate companion for an entry-level maker learning electronics. This kit is your friend whenever you need to build up a project. It contains many of our most popular components and prototyping parts all wrapped up in one parts pack so you can open up and dig right in.
Kit Contents:
Prototyping:
- 1x - Storage box with latch
- 1x - Half-size breadboard
- 20x - Male/male jumper wires - 3" (75mm)
- 10x - Male/male jumper wires - 6" (150mm)
LEDs:
Capacitors:
- 10x - 1.0uF Ceramic capacitors
- 10x - 0.1uF Ceramic capacitors
- 10x - 0.01uF Ceramic capacitors
- 5x - 10uF 50V Electrolytic capacitors
- 5x - 100uF 16V Electrolytic capacitors
Resistors:
- 10x - 560 ohm 5% axial resistors
- 10x - 1K ohm 5% axial resistors
- 10x - 10K ohm 5% axial resistors
- 10x - 47K ohm 5% axial resistors
Semiconductors:
- 5x - 1N4001 Diodes
- 5x - 1N4148 Signal Diodes
- 5x - NPN Transistor PN2222 TO-92
- 5x - PNP Transistor PN2907 TO-92
- 2x - 5V 1.5A Linear voltage regulator - 7805 TO-220
- 1x - 3.3V 800mA Linear voltage regulator - LD1117-3.3 TO-220
- 1x - TLC555 wide-voltage range, low-power 555 Timer
- 1x - LM358 Dual operational Amplifier
Sensors:
- 1x - Photocell
- 1x - Thermistor (Breadboard version)
- 1x - Vibration sensor switch
- 1x - 10K Breadboard trim potentiometer
- 1x - 1K Breadboard trim potentiometer
Mechanical:
- 1x - Piezo buzzer
- 5x - 6mm Tactile switches
- 3x - SPDT slide switches
- 1x - 40-pin Break-away male header strip
- 1x - 40-pin female header strip
-
Technical Details
Technical Details+
-
Learn
Learn+
Program the 'Hello World' of hardware with MicroPython.Blink LEDs and read buttons with digital I/O and MicroPython!Use ADC's, DAC's, and PWM outputs to control analog signals with MicroPython!This Cold War-era mystery box's disarm code must be toggled in before the timer reaches zero!
Level shifters are like little bilingual translators for your electronics!Build a huge timer for an event or race. It's a digital segment display made from RGB NeoPixels!Learn how to control digital inputs and outputs with CircuitPython!Learn how to control analog, or continuous voltage, values with CircuitPython!
Make a nice, cold beverage using thermoelectric cooling!
Blink those LEDs with the BBC micro:bit
MAY WE ALSO SUGGEST...
MAY WE ALSO SUGGEST...-
-
Distributors+
See our Distributors page for a complete list of distributors.
Ordering full reels vs. cut reels
Adafruit NeoPixel Digital RGB LED strips come to us in 4 or 5 meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires as shown in the pic below. If you order a full 4 or 5 meters, you get the full reel with both connectors installed (like the pic below).
If you buy less than a full reel, you'll get a single strip, but it will be a cut piece from a reel which may or may not have a connector on it. If the piece comes from the end of the reel, the connector may be on the output end of the strip!
