SEARCH RESULTS FOR: perma proto

... in the Adafruit Blog

... in the Adafruit Customer Support Forums

PRODUCTS:

Adafruit Perma-Proto Half-sized Breadboard PCB - Single

PRODUCT ID: 1609

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake...

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a solderless breadboard and then transferring the parts to a more permanent PCB. That's when we realized what people would really like is a proto board that makes it easy! This proto-board is the PCB...

$4.50

IN STOCK

Adafruit Perma-Proto Quarter-sized Breadboard PCB - Single

PRODUCT ID: 1608

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake...

$2.95

IN STOCK

Adafruit Perma-Proto Half-sized Breadboard PCB - 3 Pack!

PRODUCT ID: 571

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake...

$12.50

IN STOCK

Adafruit Perma-Proto HAT for Pi Mini Kit - No EEPROM

PRODUCT ID: 2310

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector)...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to...

$4.95

IN STOCK

Adafruit Perma-Proto Quarter-sized Breadboard PCB - 3 Pack!

PRODUCT ID: 589

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake...

$8.50

IN STOCK

Adafruit Perma Proto Bonnet Mini Kit

PRODUCT ID: 3203

Design your own Bonnet or pHAT, attach custom circuitry and otherwise dress your Pi Zero with this jaunty prototyping Bonnet kit! To add to the...

Design your own Bonnet or pHAT, attach custom circuitry and otherwise dress your Pi Zero with this jaunty prototyping Bonnet kit! To add to the Adafruit Bonnet party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with...

$4.50

IN STOCK

Adafruit Perma-Proto Full-sized Breadboard PCB - Single

PRODUCT ID: 1606

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake...

$6.95

IN STOCK

Adafruit Perma-Proto Full-sized Breadboard PCB - 3 Pack!

PRODUCT ID: 590

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake...

$19.95

IN STOCK

Adafruit Perma-Proto Mint Tin Size Breadboard PCB

PRODUCT ID: 723

Making a project that will fit into a "Altoids" Mint Tin? Put down that PCB shear and pick up a Perma-Proto in the new exciting minty...

Making a project that will fit into a "Altoids" Mint Tin? Put down that PCB shear and pick up a Perma-Proto in the new exciting minty shape! Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a solderless breadboard and then transferring the...

$5.95

IN STOCK

Adafruit Perma-Proto Small Mint Tin Size Breadboard PCB - 3 pack

PRODUCT ID: 1214

Making a project that will fit into a "Altoids Smalls" Mint Tin? Or maybe you just need a small amount of prototyping space and a larger...

Making a project that will fit into a "Altoids Smalls" Mint Tin? Or maybe you just need a small amount of prototyping space and a larger breadboard size is too big? Put down that PCB shear and pick up a Perma-Proto in the new exciting shape! Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how...

$7.95

IN STOCK

Adafruit Perma-Proto HAT for Pi Mini Kit - With EEPROM

PRODUCT ID: 2314

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with which...

$7.50

61 IN STOCK

Adafruit Perma-Proto Super Pack!

PRODUCT ID: 591

Pick up a super pack of our Perma-Proto PCBs, perfect for professional prototyping projects! This super pack contains 3 each of our 3 sizes - 9 PCBs...

Pick up a super pack of our Perma-Proto PCBs, perfect for professional prototyping projects! This super pack contains 3 each of our 3 sizes - 9 PCBs total. You'll always have the right size for whatever you're working on. Pack contains: Three quarter-sized Perma-Proto PCBsThree half-sized Perma-Proto PCBsThree full-sized Perma-Proto PCBs Nine PCBs total

$34.95

IN STOCK

Adafruit Perma-Proto 40-Pin Raspberry Pi Breadboard PCB Kit - with 2x20 Header

PRODUCT ID: 4354

We put a PermaProto full-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi!...

We put a PermaProto full-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4,...

$7.95

89 IN STOCK

Adafruit Perma-Proto 40-Pin Raspberry Pi Half-Size PCB Kit - with 2x20 Header

PRODUCT ID: 4353

We put a PermaProto half-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi!...

We put a PermaProto half-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with extra prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4,...

$5.95

37 IN STOCK

Adafruit Perma-Proto Raspberry Pi Breadboard PCB Kit

PRODUCT ID: 1135

This version is no longer made, as most people are not using Pi's with 2x13 connectors such as the Pi 1 Model B We stock a version for newer...

This version is no longer made, as most people are not using Pi's with 2x13 connectors such as the Pi 1 Model B We stock a version for newer Pi's with 2x20 headers so please pick that one up for any modern Pi usage! We put a PermaProto full sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get...

MORE INFO

DISCONTINUED

Adafruit Flex Perma-Proto - Half-sized Breadboard Flex-PCB

PRODUCT ID: 1518

Make your next project super-flexy with a prototyping board that can twist and bend. We took our lovely classic perma-proto design and had it made...

Make your next project super-flexy with a prototyping board that can twist and bend. We took our lovely classic perma-proto design and had it made from incredibly thin polyamide film. It's extremely bendable, and you can cut it easily with scissors. It has a bend radius of 1cm or better (you can also crease it but that might break a trace if you crease a trace) and you can solder any components to the pads. Sensors? Wearables?...

$7.50

48 IN STOCK

Circuit Playground Proto Gizmo - Bolt-on Perma-Proto

PRODUCT ID: 4320

Extend and expand your Circuit Playground projects with a bolt on Perma-Proto that lets you connect solderable circuits in a sturdy and reliable...

Extend and expand your Circuit Playground projects with a bolt on Perma-Proto that lets you connect solderable circuits in a sturdy and reliable fashion. This PCB looks just like a solderless breadboard but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Solder to the gold-plated traces to create your custom invention! Each pad of the Circuit Playground has a large oval pad you can connect to, and in the...

$7.95

15 IN STOCK

Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB Kit

PRODUCT ID: 1171

We put a PermaProto quarter-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It...

We put a PermaProto quarter-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always...

$7.95

54 IN STOCK

Adafruit Half-size Perma-Proto Raspberry Pi Breadboard PCB Kit

PRODUCT ID: 1148

We put a PermaProto half sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has...

We put a PermaProto half sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always...

MORE INFO

DISCONTINUED

Pocket PiGRRL Pack Build your own Pi Game Emulator! - CASE + PI NOT INCLUDED

PRODUCT ID: 2510

For all those who feared their Game Boy days would be but a memory, worry no more! The Game Boy may be dead, but with this pack you'll...

For all those who feared their Game Boy days would be but a memory, worry no more! The Game Boy may be dead, but with this pack you'll have a chance to revive it in style. We've collected all the right parts so you can assemble the guts of your very own DIY GameGRRL - a portable Raspberry Pi running MAME, NES, Atari2600 and other fine emulators (via RetroPie/EmulationStation) It's called the Pocket PiGRRL and it's...

NOTIFY ME

$47.50

OUT OF STOCK

Assembled Pi T-Cobbler Plus - GPIO Breakout - Pi A+, B+, Pi 2/3/4, Zero

PRODUCT ID: 2028

This is the assembled version of the Pi T-Cobbler Plus. It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi...

This is the assembled version of the Pi T-Cobbler Plus. It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi with 2x20 connector) The Raspberry Pi has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and...

$7.95

IN STOCK

Breadboard-Friendly 3.5mm Stereo Headphone Jack

PRODUCT ID: 1699

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and...

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 0.1" spacing so it plugs very solidly into a breadboard, perma-proto or perf-board. Each order comes with one headphone jack, breadboard and audio cable not included!...

$0.95

IN STOCK

Bakelite Universal Perfboard Plates - Pack of 10

PRODUCT ID: 2670

Make your next project as you imagine it with prototyping perfboards that can easily be cut with scissors like these Bakelite Universal...

Make your next project as you imagine it with prototyping perfboards that can easily be cut with scissors like these Bakelite Universal Perfboard Plates ! We wanted a perfboard that was both customizable and durable and bakelite was the answer. Like most perfboards these plates come on thin (1.2mm) sheets with holes drilled in a grid, each spaced 0.1" apart. There are some big copper pads (for mechanical connections?...

$4.95

IN STOCK

Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board

PRODUCT ID: 2448

Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel using the TB6612. These are perhaps...

Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel using the TB6612. These are perhaps better known as "the drivers in our assembled Adafruit Motorshield or Motor HAT." We really like these dual H-bridges, so if you want to control motors without a shield or HAT these are easy to include on any solderless breadboard or perma-proto. We solder on TB6612 onto a breakout...

$4.95

IN STOCK

Mini Solderless Breadboard - 2x4 Points

PRODUCT ID: 2017

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x4 point solder-less breadboard is a good...

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x4 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have a couple points. In our example photo, we put a chip and some jumper wires in the breadboard, but you can use anything with 0.1" spaced header. Comes with one 18mm x 8mm x 8mm piece of solder-less breadboard. There are...

$0.75

22 IN STOCK

Adafruit Pi T-Cobbler Plus Kit Breakout for 2x20 Raspberry Pi - RasPi A+, B+, Pi 2, Pi 3, Zero

PRODUCT ID: 1989

The Raspberry Pi A+/B+/Pi 2/Pi 3/Zero has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And...

The Raspberry Pi A+/B+/Pi 2/Pi 3/Zero has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Pi's 40 pins. That's why we now carry the Adafruit Pi T-Cobbler Plus Kit - Breakout + Cable for Raspberry Pi. This Cobbler...

$7.50

29 IN STOCK

IDC Breakout Helper - 2x8 (16 pin)

PRODUCT ID: 2104

This 2x8 (16 pin - 0.1" spaced) IDC Breadboard Helper is great in conjunction with any 16-pin IDC cables. It comes in two...

This 2x8 (16 pin - 0.1" spaced) IDC Breadboard Helper is great in conjunction with any 16-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...

NOTIFY ME

$1.25

OUT OF STOCK

Assembled Pi Cobbler Plus - Breakout Cable - for Pi B+/A+/Pi 2/Pi 3/Pi 4

PRODUCT ID: 2029

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY...

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s / Pi 2's / Pi 3 / Pi 4's 40 pins. That's why we now carry the Adafruit Assembled Pi...

$6.95

IN STOCK

IDC Breakout Helper - 2x5 (10 pin)

PRODUCT ID: 2102

This little 2x5 (10 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with any of our 10-pin IDC cables. It comes in two...

This little 2x5 (10 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with any of our 10-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...

$0.95

57 IN STOCK

Vertical Breadboard-Friendly 3.5mm Mono Headphone Jack

PRODUCT ID: 4031

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll...

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. The pins are on 0.1" spacing so it plugs very solidly ( and vertically! ) into a breadboard, perma-proto or perf-board. Works best if...

NOTIFY ME

$1.25

OUT OF STOCK

Adafruit Assembled Pi T-Cobbler Breakout for Raspberry Pi

PRODUCT ID: 1754

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it....

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an assembled add on prototyping Pi T-Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy. Designed for...

$6.95

IN STOCK

Raspberry Pi Model B+ 512MB RAM

PRODUCT ID: 1914

OMG OMG OMG, did you hear? There's a Raspberry Pi called the Model B+ and check it out...more USB ports, more GPIO, better power supply,...

OMG OMG OMG, did you hear? There's a Raspberry Pi called the Model B+ and check it out...more USB ports, more GPIO, better power supply, four mounting holes, less sticky-out SD card! Yep, that's right, the fantastic engineers at Raspberry Pi HQ have blessed us with a new design. They've taken all the feedback over the last 3 years and rolled out a nice updated Pi with many fixes and extras...all at the same price! Take a deep...

NOTIFY ME

$29.95

OUT OF STOCK

Mini Solderless Breadboard - 2x8 Points

PRODUCT ID: 2018

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x8 point solder-less breadboard is a...

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x8 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have a couple points. In our example photo, we put a Trinket in the breadboard, but you can use anything with 0.1" spaced header. Comes with one 29mm x 8mm x 8mm piece of solder-less breadboard. There are two white posts on...

$0.95

IN STOCK

IDC Breakout Helper - 2x20 (40 pin)

PRODUCT ID: 2270

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular...

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2 (40 pins). It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so...

NOTIFY ME

$2.25

OUT OF STOCK

Mini Solderless Breadboard - 4x4 Points

PRODUCT ID: 2463

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 4x4 point solder-less breadboard is a good...

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 4x4 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have a couple points. Comes with one 18mm x 13mm x 10mm piece of solder-less breadboard. There are four white posts on the bottom for PCB positioning, but you can cut them off with diagonal cutters if you dont want them.

$0.95

74 IN STOCK

Flanged Weatherproof Enclosure With PG-7 Cable Glands

PRODUCT ID: 3931

Whether you're raiding tombs or traversing nuclear fallout wastelands, this is the most heavy-duty enclosure for your project! Weatherproof?...

Whether you're raiding tombs or traversing nuclear fallout wastelands, this is the most heavy-duty enclosure for your project! Weatherproof? Check. Tough polycarbonate cover? Check. Built-in gasket seal? Oh yeah, check. Store your project safe and sound in this Flanged Weatherproof Enclosure . We especially like the machinable ABS plastic body, four mounting holes, and the easy-open screws that can be taken apart as many times...

$9.95

83 IN STOCK

IC Socket - for 20-pin 0.3" Chips - Pack of 3

PRODUCT ID: 2204

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 20 pin...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 20 pin 0.3" wide version. Best used with chips that have 20 pins (2x10) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you...

NOTIFY ME

$0.95

OUT OF STOCK

IC Socket - for 16-pin 0.3" Chips - Pack of 3

PRODUCT ID: 2203

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 16 pin...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 16 pin 0.3" wide version. Best used with chips that have 16 pins (2x8) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you...

$0.95

IN STOCK

Small Plastic Project Enclosure - Weatherproof with Clear Top

PRODUCT ID: 903

Store your project safe and sound in this nice weatherproof box with a clear top. We picked up this box because we like the machinable ABS plastic...

Store your project safe and sound in this nice weatherproof box with a clear top. We picked up this box because we like the machinable ABS plastic body and tough clear polycarbonate cover, the built in weatherproof gasket seal, and the easy-open screws that can be taken apart as many times as you wish without worrying about cracking or stripping. This box measures 80mm x 110mm x 45mm externally. You can fit an Adafruit Metro, Raspberry Pi Zero,...

NOTIFY ME

$9.95

OUT OF STOCK

IC Socket - for 8-pin 0.3" Chips - Pack of 3

PRODUCT ID: 2202

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 8 pin...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 8 pin 0.3" wide version. Best used with chips that have 8 pins (2x4) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you...

$0.75

IN STOCK

Configurable Spring Terminal Blocks - 3 Pin 0.1" Pitch R/A - x 5

PRODUCT ID: 1074

Spring terminal blocks will simplify your wiring and make your project more rugged. Instead of soldering wires to your perf board, solder in these...

Spring terminal blocks will simplify your wiring and make your project more rugged. Instead of soldering wires to your perf board, solder in these 0.1" pitch terminal blocks. There's a little spring contact so you can pull back on the plastic bit and slip in your 20 to 26 AWG solid or stranded-core wires. Each terminal block is electrically isolated from those next to it. Each block also has two solder pins per contact for strong...

$4.95

8 IN STOCK

IDC Breakout Helper - 2x3 (6 pin)

PRODUCT ID: 2105

This little 2x3 (6 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with our 6-pin IDC cable. It comes in...

This little 2x3 (6 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with our 6-pin IDC cable. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...

$0.95

69 IN STOCK

USB Type-A Jack

PRODUCT ID: 2225

This is just a standard USB-A jack. It's a sturdy metal with 4 pins in the back and 2 small mounting tabs that make it easy to use in your...

This is just a standard USB-A jack. It's a sturdy metal with 4 pins in the back and 2 small mounting tabs that make it easy to use in your next USB project We use this USB-A jack for everything, really. With a little effort you can bend the side mounting tabs and solder the 4 data/power pins into a Perma Proto. Its not good for solderless breadboards, the pins are not very long.

$0.75

60 IN STOCK

Configurable Spring Terminal Blocks - 3 Pin 0.1" Pitch x 5

PRODUCT ID: 1081

Spring terminal blocks will simplify your wiring and make your project more rugged. Instead of soldering wires to your perf board, solder in these...

$4.95

49 IN STOCK

IDC Breakout Helper - 2x16 (32 pin)

PRODUCT ID: 2103

This 2x16 (32 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with any 32-pin IDC cables. It comes in two...

This 2x16 (32 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with any 32-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...

$1.95

IN STOCK

IDC Breakout Helper - 2x13 (26 pin)

PRODUCT ID: 2101

The "poor woman's" Raspberry Pi cobbler! This combo of 2x13 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for...

The "poor woman's" Raspberry Pi cobbler! This combo of 2x13 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A and B. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with...

$1.75

29 IN STOCK

Adafruit Pi Unassembled T-Cobbler Breakout Kit for Raspberry Pi

PRODUCT ID: 1105

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it....

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi T-Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy. Designed for Raspberry Pi...

MORE INFO

DISCONTINUED

IC Socket - for 28-pin 0.6" Chips - Pack of 3

PRODUCT ID: 2206

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 28 pin...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 28 pin 0.6" wide version. Best used with chips that have 28 pins (2x14) and have 0.6" pin spacing. We also have 0.3" version, so don't use this for 'skinny' 28p in chips These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips...

$1.25

30 IN STOCK

IC Socket - for 28-pin 0.3" Chips - Pack of 3

PRODUCT ID: 2205

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 28 pin...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 28 pin 0.3" wide version. Best used with chips that have 28 pins (2x14) and have 0.3" pin spacing. We also have 0.6" version, so don't use this for 'wide' 28p in chips These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips...

NOTIFY ME

$1.25

OUT OF STOCK

IC Socket for 40-pin 0.6" Chips - Pack of 3

PRODUCT ID: 2207

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 40 pin...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 40 pin 0.6" wide version. Best used with chips that have 40 pins (2x20) and have 0.6" pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you...

$1.50

IN STOCK

Adafruit Assembled Pi Cobbler Breakout + Cable for Raspberry Pi - Model B

PRODUCT ID: 914

Now that you've finally got your hands on a Raspberry Pi® Model B , you're probably itching to make some fun embedded computer projects...

Now that you've finally got your hands on a Raspberry Pi® Model B , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the Pi super easy. Designed for use with...

MORE INFO

DISCONTINUED

IC Sockets - Packs of 3 - Various Sizes

PRODUCT ID: 2309

An IC socket (Integrated Circuit socket) allows you to insert and remove chips easily from an assembled kit or project We have a range of pins and...

An IC socket (Integrated Circuit socket) allows you to insert and remove chips easily from an assembled kit or project We have a range of pins and different widths to choose from to fit a variety of different chips; choose your size from the pull-down on the right! These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin...

MORE INFO

IN STOCK

Adafruit Pi Cobbler + Kit- Breakout Cable for Pi B+/A+/Pi 2/Pi 3

PRODUCT ID: 1990

The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use...

The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s 40 pins. That's why we now carry the Adafruit Pi Cobbler Plus - Breakout and Cable for Raspberry Pi B+. It's an add on...

MORE INFO

DISCONTINUED