These little cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits, and have a few handy in our ARM-dev box. We thought you may want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is 0.06mm/0.025" pitch and the connector is a 1.27mm (0.05") pitch 2x5 box....

Battery power for your portable project! These batteries are good quality at a good price, and work fantastic with any of the kits or projects in the shop that use AAA's. This is a pack of 2 AAA batteries . These batteries are Alkaline (MnO2) chemistry, with a voltage range of 1.6V (fresh) to 0.8V (dead). The mAh capacity depends on discharge usage but at 25mA rate it is 1200mAh (check the datasheet in the download tab for more...

The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Instead of a L293D darlington driver, we now have the TB6612...

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 9V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC wall power, you'll just need a low cost plug adapter. New! This adapter is now CE /...

These Banana Plugs not only look great, they're also solder-free and stackable ! Banana plugs are often used on test equipment, tools, synthesizers and other electronic patch panels. Each connector is designed with bowed strips to provide secure and uniform contact between the plug and jack. Even after multiple insertions, the non-collapsing design stays true to form. The plug springs are nickel-plated Beryllium copper and will...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your very...

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with a Micro SD Card Extender . This simple, but effective device gives you a long flexible cable, a psuedo Micro SD card on one end, and a matching micro SD card socket on the other. Plug in the card half and attach the socket wherever you like. This is a great hack for length constraints with 3D printers, single-board computers,...

Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 diffused red LEDs 5mm diameter 660 nm wavelength 1.85-2.5V Forward Voltage, at 20mA current 250 mcd typical brightness Datasheet If you need some help using LEDs, please...

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable clips. There are options a-plenty! This is the 10 cm (~4 inches) version. The two required HDMI adapters are not included! Check out all of...

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 12V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC wall power, you'll just need a low cost plug adapter. New! This...

A Feather board without ambition is a Feather board without FeatherWings! This is the  DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight! The original Adafruit Motorshield Kit...

This is a cute half-size breadboard with an assortment of small jumper wires, great for prototyping. Breadboard is 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. Power rails can be pulled off easily to make the breadboard as thin as 1.4" (3.5cm). The jumper wires are pre-cut and bent in right angles at the ends, so you can choose the appropriate length for your...

Need some really bright LEDs? We are big fans of these clear white LEDs, in fact we use them exclusively in our kits. They are very bright and have about 25 degree LED beam so they're good for illumination, head lamps, spotlights, etc. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear white LEDs 5mm diameter Cool White color 3.0V Typical Forward Voltage, at 20mA current 15,000 mcd minimum...

Have you ever been in a situation where you desperately needed a screwdriver right away ? Now you can have one at-the-ready all the time — enter the Adafruit Pocket Screwdriver ! OK, it's a little tough to write exciting copy for a pocket screwdriver, but really this one is truly great for Adafruit customers. The Phillips head fits the 3.5mm terminal blocks we have on many of our kits, and the slot is great for the common...

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable clips. There are options a-plenty! This is the 20 cm (~8 inches) version. The two required HDMI adapters are not included! Check out all of...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to...

This 1.27mm pitch, 2x5 male SMT Box Header is the same one used on our SWD Cable Breakout Board. The header alone is great if you want to incorporate this piece of hardware with your own software. We're specifically selling it so you can solder it onto our nRF52 Feather to add SWD debug/connect capabilities. You could also straighten out the SMT pins to solder into a thru-hole connector. This little guy will snap right into any 10-pin...

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear blue LEDs 5mm diameter 465 nm wavelength 3.2-3.8V Forward Voltage, at 20mA current 6000 mcd typical brightness Viewing Angle : ±10 degrees Maximum continuous current: 30mA If...

As any engineer will tell you, 0.1uF ceramic capacitors are the magic fairy dust of electronics - sprinkle them over your circuit schematics for good luck! But seriously, a 0.1uF capacitor right next to the VCC pin of your chips will improve stability by filtering out power supply spikes and noise that can cause flaky behavior. We love these little guys, they have 0.1" spacing so fit into any perf or breadboard, compact and good quality. We...

Here's yet another addition to our family of AA battery holders. It's a holder for five (5) AA batteries, with 5" wire leads. It's black and has a 2.1mm barrel plug (tip positive). 5 x AA battery packs are best used with Arduino-compatibles and other dev boards with 2.1mm DC jacks and a 5V regulator, because 5V regulators tend to like 1-2V of overhead. 4 x AA battery holders would give you ~6VDC, which is just a tiny...

Need some really bright LEDs? We are big fans of these clear red LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear red LEDs 5mm diameter 640 nm wavelength 1.8-2.2V Forward Voltage, at 20mA current 1500 mcd typical brightness Viewing Angle : ±10 degrees Maximum continuous current: 30mA If you...

In collaboration with Microsoft, Adafruit's releasing IoT Starter Kits with boards, sensors, and components that are 'Azure Certified for IoT.' Azure is Microsoft's cloud solution for IoT projects that's a comprehensive and flexible program from the Microsoft team that they're extending into the open source hardware world.  This starter kit includes a pre-soldered Adafruit Feather HUZZAH...

We like capacitors so much we made a kids show about them.   They're super handy and it's really helpful to have a variety lying around to pick and choose from. This is a 10 pack of  100uF 16v  capacitors so they can be used with any DC voltage up to 16V.  They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (left bend) HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to...

When you need to amplify, filter, add, or otherwise manipulate analog signals you'll certainly want an operational amplifier at your side. This is our favorite hobby op-amp, which we use in our kits! It's DIP package so very easy to work with on a breadboard or perfboard. It has two amplifiers inside. It can run from voltages as low as 2.7V and up to 6V. It has rail to rail input and output, which is a common problem for beginners who...

We like capacitors so much we made a kids show about them.   They're super handy and it's really helpful to have a variety lying around to pick and choose from. This is a 10 pack of  10uF 50v  capacitors, so they can be used with any DC voltage up to 50V.  They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are...

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable clips. There are options a-plenty! This is the 30 cm (~12 inches) version. The two required HDMI adapters are not included! Check out all of...

Need some indicators? We are big fans of these diffused green LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 diffused green LEDs 5mm diameter 565 nm wavelength 2.2-2.5V Forward Voltage, at 20mA current 40 mcd typical brightness (green LEDs will appear brighter to us than other...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Micro HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

Need some really bright LEDs? We are big fans of these clear green LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear green LEDs 5mm diameter 520 nm wavelength 3.2-3.8V Forward Voltage, at 20mA current 8000 mcd typical brightness Viewing Angle : ±10 degrees Maximum continuous current: 30mA...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Mini HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with an SD Card Extender . This simple, but effective device gives you a long flexible cable, a pseudo-card on one end, and an SD card socket on the other. Plug in the SD card half and attach the socket wherever you like. This is a great hack for length constraints with 3D printers, single-board computers, data-logging kits and more. Get to...

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Plate from Adafruit, which can snap onto the Pi PCB (and is removable later if you wish) and gives you all sorts of prototyping goodness to make building on top of the Pi super easy. Note: This kit is best used for the Raspberry Pi Model A or Model B. You...

Battery power for your portable project! These batteries are high quality at a good price, and work fantastic with any of the kits or projects in the shop that use 9V These batteries are Alkaline (MnO2) chemistry, with a voltage range of 9.6V (fresh) to 4.8V (dead). The mAh capacity depends on discharge usage but at 50mA rate it is about 500mAh (check the datasheet in the download tab for more details) These work perfectly with our 9v clip, 9v...

This antenna is a perfect addition to your cellular project with LTE connectivity. It's specifically intended for use with the Pycom LTE-powered kits but it's just a passive antenna so you can pair it with any dev board you like, as long as it has a uFL connector. Comes with a flexible copper grounding sticker, you can use to provide a nice big ground plane!

In 1970, John Conway came up with a 1-player game called Game of Life. The Game of Life is a mathematical game that simulates 'colonies' that grow or die based on how crowded or lonely they are and is known for the way it creates a beautiful organic display out of randomness. Here is a design for a simple electronic project that plays Conway's Game of Life. Make one kit and keep it on your desk, or attach multiple kit modules...

Need some really bright LEDs? We are big fans of these clear yellow LEDs, in fact we use them exclusively in our kits. They are very bright! They go easily into a breadboard and will add that extra zing to your project. This comes in a pack of 25! If you need some help using LEDs, please read our "Introduction to using LEDs" tutorial for any electronics project.

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight HDMI socket . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your very...

With so many connectivity options, Pycom's  LoPy4 is a lot like an amazing, multi-course brunch. You've got LoRa playing your favorite morning public access radio station, WiFi talking to your smart coffee maker, SigFox and cream cheese on a bagel, and a baker's dozen of Bluetooth muffins-- I mean, blueberry muffins! Boosted with the Espressif ESP32 chipset, the LoPy is one of the fanciest...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) Mini HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop...

Battery power for your portable project! These batteries are good quality at a good price, and work fantastic with any of the kits or projects in the shop that use AAs. This is a pack of 4 AA batteries . These batteries are Alkaline (MnO2) chemistry, with a voltage range of 1.6V (fresh) to 0.8V (dead). The mAh capacity depends on discharge usage but for AA alkaline batteries it is typically 3000mAh (check the datasheet in the download tab...

Forrest M. Mims III is a trusted name in the electronics world for good reason: his charming and engaging texts have drawn millions of people into the world of electronics for the first time. Star Simpson has created an electronic tribute to those hand-drawn circuits by bringing the projects to life. These kits are an exquisitely designed series of finely crafted and highly detailed boards. These are the Circuit Classics . They make a great gift...

Forrest M. Mims III is a trusted name in the electronics world for good reason: his charming and engaging texts have drawn millions of people into the world of electronics for the first time. Star Simpson has created an electronic tribute to those hand-drawn circuits by bringing the projects to life. These kits are an exquisitely designed series of finely crafted and highly detailed boards. These are the Circuit Classics . They make a great gift...

Forrest M. Mims III is a trusted name in the electronics world for good reason: his charming and engaging texts have drawn millions of people into the world of electronics for the first time. Star Simpson has created an electronic tribute to those hand-drawn circuits by bringing the projects to life. These kits are an exquisitely designed series of finely crafted and highly detailed boards. These are the Circuit Classics . They make a great gift...

Locate your stuff! The Asset Tracker Kit  from Particle contains all of the pieces you need to build a Cellular + GPS location tracker for your most prized possessions. In addition to a GPS Shield, the Asset Tracker Kit comes with a weatherproof enclosure, so it’ll keep your electronics safe from the dust, dirt, and moisture of the great outdoors. Keep your bicycle, baby, and backpack safe--satellite lock onto this bargain project kit...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) Micro HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop...

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable clips. There are options a-plenty! This is the 50 cm  (~20 inches) version. The two required HDMI adapters are not included! Check out...

We like capacitors so much we made a kids show about them.   They're super handy and it's really helpful to have a variety lying around to pick and choose from. This is a 10 pack of 220uF 16v capacitors so they can be used with any DC voltage up to 16V.  They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are good for low...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (L) Micro HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft...

In collaboration with Microsoft, Adafruit's releasing IoT Starter Kits with boards, sensors, and components that are 'Azure Certified for IoT.' Azure is Microsoft's cloud solution for IoT projects.  Azure is a comprehensive and flexible program from the Microsoft team that they're extending into the open source hardware world.  This starter kit includes a pre-soldered Adafruit Feather M0 WiFi with stacking...

We like capacitors so much we made a kids show about them.   They're super handy and it's really helpful to have a variety lying around to pick and choose from. This is a 10 pack of  47uF 25v  capacitors, so they can be used with any DC voltage up to 25V.  They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are...

Drawdio is an electronic pencil that lets you make music while you draw! This fun pack has all the fun without the soldering. Essentially, its a very simple musical synthesizer that uses the conductive properties of pencil graphite to create different sounds. The result is a fun toy that lets you draw musical instruments on any piece of paper. This is the assembled version, for kits visit our kit page.   Runs on a single AAA battery for...

This shield kit pack will allow you to turn any Arduino into an AVR chip burner! It is specifically designed for people who want to program Atmega328P's to turn them into Arduino bootloader chips using an AVR-ISP sketch, but it can also be used to make a 'standalone' AVR ISP programmer - so that you can program blank chips without a computer! We use this set up in the shop to program chips for our kits. We even include a blank...

Battery power for your portable project! These batteries are good quality at a good price, and work fantastic with any of the kits or projects in the shop that use AAA's. This is a pack of 3 AAA batteries . These batteries are Alkaline (MnO2) chemistry, with a voltage range of 1.6V (fresh) to 0.8V (dead). The mAh capacity depends on discharge usage but at 25mA rate it is 1200mAh (check the datasheet in the download tab for more details)....

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (left bend) Mini HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop...

Show up stylish AND on time to any event with this awesome looking DIY watch. We have a few watch kits here at Adafruit but we finally have one that looks good and fits well, even for ladies and kids and others with smaller wrists and hands. Its got a 8x8 bit matrix display and a repurposed silicone watch band for a professional look. 64 LEDs light up to tell you the time in a variety of ways. Built into the kit are 3 different watch...

Locate your stuff! The Asset Tracker Kit  from Particle contains all of the pieces you need to build a Cellular + GPS location tracker for your most prized possessions. In addition to a GPS Shield, the Asset Tracker Kit comes with a weatherproof enclosure, so it’ll keep your electronics safe from the dust, dirt, and moisture of the great outdoors. Keep your bicycle, baby, and backpack safe--satellite lock onto this bargain project kit...

Decorate your walls with 10,000 bright stars with this Pinhole Planetarium Kit from Gakken's series of Science for Adults kits! The Pinhole Planetarium uses a small light bulb and a micro-perforated dodecahedron to cast the stars, galaxies, and constellations of the northern hemisphere onto your walls. The stellar globe can be set to project the northern hemisphere night sky for any location, date, or time. The planetarium was designed using...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Mini HDMI socket . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI adapters on each end using the flex cable clips. There are options a-plenty! This is the 100 cm  (~40 inches) version. The two required HDMI adapters are not included! Check out...

Theo Jansen's Strandbeest walks around leisurely, propelled naturally by the wind flowing through its turbines. Now you can build and enjoy your very own miniature version - a small Strandbeest that glides gracefully across surfaces without electricity or batteries. The Strandbeest is a kinetic, wind-propelled sculpture that was designed by physicist/artist Theo Jansen. While the original was designed for the beach (strandbeest is Dutch for...

Shredders unite! This handmade Mini Electric Guitar has a built-in amp and speaker. The strings on this 320mm guitar can be installed and tuned the same way as a normal sized guitar. The built-in amp and speaker output a powerful distortion sound, and an external amp can also be connected with a standard 1/4" jack for clearer & better tones. Even includes a pick that allows for easy playing! All that's needed to assemble this kit is...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Micro HDMI socket . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

Show up stylish AND on time to any event with this awesome looking DIY watch. We have a few watch kits here at Adafruit but we finally have one that looks good and fits well, even for ladies and kids and others with smaller wrists and hands. Its got a 8x8 bit matrix display and a repurposed silicone watch band for a professional look. (gif is of the red color watch kit) 64 LEDs light up to tell you the time in a variety of ways. Built into the...

Show up stylish AND on time to any event with this awesome looking DIY watch. We have a few watch kits here at Adafruit but we finally have one that looks good and fits well, even for ladies and kids and others with smaller wrists and hands. Its got a 8x8 bit matrix display and a repurposed silicone watch band for a professional look. (gif is of the red color watch kit) 64 LEDs light up to tell you the time in a variety of ways. Built into the...

Quantify the world! The Sensor Kit  from Particle is a curated mix of awesome sensors and electrical components specifically selected by the engineers on the Particle Team. If you want to measure temperature, sense loudness, measure distances, capture motion, or detect noxious gases, the Sensor Kit has you covered. Whether you’re building a connected robot or measuring the world around you, the Sensor Kit is the place to start. For a...

Show up stylish AND on time to any event with this awesome looking DIY watch. We have a few watch kits here at Adafruit but we finally have one that looks good and fits well, even for ladies and kids and others with smaller wrists and hands. Its got a 8x8 bit matrix display and a repurposed silicone watch band for a professional look. (gif is of the red color watch kit) 64 LEDs light up to tell you the time in a variety of ways. Built into the...

Show up stylish AND on time to any event with this awesome looking DIY watch. We have a few watch kits here at Adafruit but we finally have one that looks good and fits well, even for ladies and kids and others with smaller wrists and hands. Its got a 8x8 bit matrix display and a repurposed silicone watch band for a professional look. (gif is of the red color watch kit) Note: As of October 22nd, 2015, this product no longer comes with 1x CR2032...

High above the canopy, with silent wings and much to see, owls observe with their keen eyes, the view below our midnight skies. They are also sooooo adorable and cute, YA RLY! This sew-your-own owl kit by Cynthia Treen Studio is designed for beginner adults and competent young stitchers, but will delight stitchers of all levels! Materials included are: wool and rayon felt, 100% wool stuffing, embroidery needle, thread, cotton pipe cleaners,...

The Delta Twister is a build-it-yourself lightweight flying machine that's perfect for both amateur flight enthusiasts and amateur makers. The Delta Twister flies either by a wound up rubber band or a small electric motor that propels its dual-plastic wings to flap rapidly through the air. This kit requires two AAA batteries that aren't included but we sell them in the Adafruit store. No special tools are needed and there's no...

So maybe it's not "back to school" season any more - but here at Adafruit, we like to think that it's always a good time to learn something new, which we guess means that everywhere we go is a proverbial school that we're perpetually going back to.  To celebrate the continual season, we partnered with our good friends at Arrow Electronics to release custom packs of goodies called Arrow Presents: Back to School...

Evil Mad Scientist Labs never disappoints with their fantastic kits and clocks. The Alpha Clock Five is no exception: An awesome alarm clock soldering kit-- featuring five crazy-bright, crazy huge 2.3" alphanumeric LED displays in dazzling white, a Chronodot RTC (for precise quartz timing, complete with battery backup) and a handsome laser-cut acrylic case. These big 18-segment alphanumeric LED displays are notoriously difficult to drive--...

Flotilla is a range of smart, friendly, and affordable modules that you connect together to create amazing projects that can sense and react to the world around them. Brought to you by Pimoroni , the  Flotilla Mega Treasure Chest Starter Kit  is their ultimate Flotilla package. You'll get fourteen Flotilla modules, three complete kits - the audibly offensive Noisemaker synth, a cute little paper-craft mood light, and...

Locate your stuff! The Asset Tracker Kit  from Particle contains all of the pieces you need to build a GSM + GPS location tracker for your most prized possessions. In addition to a GPS Shield, the Asset Tracker Kit comes with a weatherproof enclosure, so it’ll keep your electronics safe from the dust, dirt, and moisture of the great outdoors. Keep your bicycle, baby, and backpack safe--satellite lock onto this bargain project kit...

Evil Mad Scientist Labs never disappoints with their fantastic kits and clocks. The Alpha Clock Five is no exception: An awesome alarm clock soldering kit-- featuring five crazy-bright, crazy huge 2.3" alphanumeric LED displays in red, a Chronodot RTC (for precise quartz timing, complete with battery backup) and a handsome laser-cut acrylic case. These big 18-segment alphanumeric LED displays are notoriously difficult to drive-- there are...

Battery power for your portable project! These batteries are good quality at a good price, and work fantastic with any of the kits or projects in the shop that use AAs. This is a pack of 3 AA batteries . These batteries are Alkaline (MnO2) chemistry, with a voltage range of 1.6V (fresh) to 0.8V (dead). The mAh capacity depends on discharge usage but for AA alkaline batteries it is typically 3000mAh (check the datasheet in the download tab for...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo.   100% Heavy Cotton (185gms) Full colour screen-printed logo Preshrunk. Machine washable....

Delve into the traditional Japanese art of origami and produce softly lit origami paper. You can make a lampshade using either a square-folded shade or a polygonal shape and then switch between different color lights! Each of the three LED colors can be dimmed individually or set to auto-fade. The concept and design of the AKARI Origami came about from a collaboration between Japanese artist Hiroyuki Moriwaki and the origami designer Miyuki...

Learn about energy sources and how to "think green". Build over 125 projects and learning about environmentally friendly energy and how electricity works. Includes full-colored manual with over 100 pages and separate educational manual. Features-Hand Crank-Solar Cell-FM Radio-Energy Compartment-Rechargeable Battery-Windmill-Clock and Analog Meter. Compatible with the Snap Circuits family of electronic learning kits. Features Build over...

ArcBotics’ Hexy the Hexapod is a fully articulated hexapod robot kit. Hexy has six legs, 19 servo motors and is powered by Arduino, while maintaining a price 4-10x less expensive than current hexapod robots. It makes complex robotics less costly, easier to learn with the tutorials and documentation, while being radically more fun (and cute!). At the same time its built with completely open source hardware and software, making discovery and...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo.   100% Heavy Cotton (185gms) Full colour screen-printed logo Preshrunk. Machine washable....

Quantify the world! The Sensor Kit  from Particle is a curated mix of awesome sensors and electrical components specifically selected by the engineers on the Particle Team. If you want to measure temperature, sense loudness, measure distances, capture motion, or detect noxious gases, the Sensor Kit has you covered. Whether you’re building a connected robot or measuring the world around you, the Sensor Kit is the place to start. For a...

Pianists? No! Pannists? Yes! Educate yourself on the sounds of Trinidad and Tobago with Gakken's Steel Drum Kit. Put together a four-note steelpan with an 1/8th inch output and ride the soundwaves down to the Caribbean islands. The kit includes the drum, a pickup that magnetizes to the bottom of the drum, a stand for the drum, mallets, and an 1/8th inch out. Amplifier and batteries not included! Like many of our Gakken kits, the...

The Gakken Twin Lens Reflex Camera is perfect for anyone who loves photography or electronics. This highly portable camera, when assembled, has a unique appearance with a pair of vertically arranged lenses. The upper lens is used to set the view, angle, and focus the camera, while the bottom lens is used to take the actual photographs. Use any 35mm color/slide/b&w film (not included!) The kit also includes stickers to decorate your camera...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black with the Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo.   100% Heavy Cotton (185gms) Full colour screen-printed logo Preshrunk. Machine...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo.   100% Heavy Cotton (185gms) Full colour screen-printed logo Preshrunk. Machine washable....

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo.   100% Heavy Cotton (185gms) Full colour screen-printed logo Preshrunk. Machine washable....

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo.   100% Heavy Cotton (185gms) Full colour screen-printed logo Preshrunk. Machine washable....

The Pibow is a durable and fun case for the Raspberry Pi® computer that is perfectly in touch with the ethos of the Raspberry Pi. The case is crafted out of six layers with a transparent top and base. Each layer is laser cut from high-quality cast acrylic and once stacked they securely contain a Raspberry Pi Model A while leaving the primary ports accessible. Weighing only 67 grams the case is lightweight and ideal for mounting to any...

This is a lovely way to get started with Bare Conductive paint, with three fun electronic greeting cards. Use the included 10 mL pen to draw traces and connect components on the front of the card. All three cards have cute robots with blinkie eyes or hearts. Comes with: Three cards, one 10mL Bare Conductive pen, 3 x LEDs, 3 x 3v coin batteries. Bare Conductive Paint is a multipurpose electrically conductive material perfect for all of your DIY...

Drawdio is an electronic pencil that lets you make music while you draw! It's great project for beginners: An easy soldering kit with instant gratification. Essentially, its a very simple musical synthesizer that uses the conductive properties of pencil graphite to create different sounds. The result is a fun toy that lets you draw musical instruments on any piece of paper. Runs on a single AAA battery for many hours (even 'nearly...

The world's first and only open-source hardware charger: The MintyBoost®! New version! Works with the new iPhone 4 & 5 and more! Please review the Minty Boost project page(s) before purchase and assembly!, some phones require different modifications to the kit to charge properly! Some phones such as the *iPhone 3gs are very sensitive to charging via USB and may not work in all environments or configurations. Make your own...

The MintySynth kit - 2.0 is a great way to make your next musical creation while experimenting with electronics and programming.  Open source and hackable, the MintySynth is an Arduino-compatible synth kit that fits in an Altoids tin. This comes as an unassembled kit so some soldering is required - but the assembly itself is fairly straightforward and the software comes preloaded so creating your next project should be a breeze!...

Welcome to the Internet of Things with Google! Whether you are a device creator prototyping a new design for production, or a hobbyist looking for an introduction to the new Android Things API, you've come to the right place. It's time to get your Android enabled hardware working with Google services. Android Things is an Android-based OS that supports new embedded single board computer like the Raspberry Pi 3 and introduces a new set of...

Octolively modules are tileable, digital interactive LED surfaces filled with ultrabright LEDs that respond in complex and gentle ways to stimulus provided by human interaction. Each Octolively module is 4 X 8 inches (10.16 X 20.32 cm) in size, and features eight huge (10 mm) ultrabright LEDs, spaced along a two-inch grid. Each Octolively module also has eight infrared proximity sensors-- one for every LED --to detect nearby motion, even in...

Octolively modules are tileable, digital interactive LED surfaces filled with ultrabright LEDs that respond in complex and gentle ways to stimulus provided by human interaction. Each Octolively module is 4 X 8 inches (10.16 X 20.32 cm) in size, and features eight huge (10 mm) ultrabright LEDs, spaced along a two-inch grid. Each Octolively module also has eight infrared proximity sensors-- one for every LED --to detect nearby motion, even in...

These two  Female Headers  alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do? They get soldered on either side of the Feather board. Now you can plug in FeatherWings to add more capability to your portable project. Unlike our Feather Stacking Headers, they aren't designed to 'stack', but they're more compact. Note: Comes with one 12-pin and...

Want to create your own computer but unsure of where to start? Our Computer Kit for Raspberry Pi 3 might be just the thing you need to get your gears in motion! This kit provides you with a keyboard, mouse, power supply, Pi enclosure, HDMI cable, and an SD card with the necessary operating system out of which you can operate. The creation of your computer begins here! Kit includes: 1 x HDMI Cable - 1 meter1 x 8GB MicroSD Card with...

This LoRa Antenna Kit  is meant for use with the LoPy LoRa, WiFi and BLE board or the SiPy Sigfox, WiFi and BLE board. But it's good for any 900MHz radio, including our LoRa breakouts/Feathers or even the RFM69 900MHz radios we stock! Includes: External antenna.RF Cable Assemblies SMA(F) JK-IPEX MHF U.FL 1.13 100MM RP-SMA Tilt Swivel 1/2 Wave Whip antenna - to match with RP-SMA connectors like this one. NOTE:  Using...

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the Blue & White 16x2 LCDs we stock in the shop. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another pin to control the backlight for a total of 7 pins. That's almost half of the pins available on a classic Arduino! With this in mind, we wanted to make it easier for people to get these LCD into their...