Female-Female 2.54 to 2.0mm Jumper Wires x 40

PRODUCT ID: 1919

These jumper wires come with a twist! Instead of going from 0.1"/2.54mm pitch headers to breadboard or something like that, these are 2.54mm to 2.0mm...

These jumper wires come with a twist! Instead of going from 0.1"/2.54mm pitch headers to breadboard or something like that, these are 2.54mm to 2.0mm ! Handy for making wire harnesses or jumpering to annoying 2mm-pitch connectors, these premium female-female jumper wires are around 8" (200mm) long and come in a 'strip' of 40. Each pair of wires has 2 pieces of 2.54mm (.1") socket on one end and a single 2x2.00mm (.08") socket on the other on the...

$6.95

IN STOCK

Premium Female/Female Jumper Wires - 40 x 6"

PRODUCT ID: 266

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are a little over 6" (150mm) long and come in a...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are a little over 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of ten colors). They have 0.1" sockets on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. We recentlty updated these so they are in a 'ribbon strip' instead of individual wires. You can always pull the ribbon wires off to make...

$3.95

IN STOCK

Premium Female/Female Jumper Wires - 20 x 6" (150mm)

PRODUCT ID: 1950

These female-female jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6"...

These female-female jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" female header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 20-pin ribbon cable. You can always pull the ribbon...

$1.95

OUT OF STOCK

Premium Female/Female Jumper Wires - 40 x 3" (75mm)

PRODUCT ID: 794

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" female header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them...

$3.95

IN STOCK

Premium Female/Female Jumper Wires - 20 x 3" (75mm)

PRODUCT ID: 1951

These female-female premium jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. They're 3" (75mm) long and...

These female-female premium jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. They're 3" (75mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" female header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 20-pin ribbon cable. You can always pull the ribbon wires off to make...

$1.95

IN STOCK

Premium Female/Female Jumper Wires - 40 x 12" (300mm)

PRODUCT ID: 793

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" female header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep...

$7.95

IN STOCK

Premium Female/Female Raw Custom Jumper Wires - 40 x 6" (150mm)

PRODUCT ID: 3141

Our Raw F/F Jumper Wires are perfect for making custom jumper wire sets for wire harnesses or jumpering between headers on PCB's. These premium...

Our Raw F/F Jumper Wires are perfect for making custom jumper wire sets for wire harnesses or jumpering between headers on PCB's. These premium jumpers are a little over 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of the ten colors). The 0.1" spacing raw sockets on either end made to be custom fitted with your choice of housing blocks to meet your prototyping needs. You can always pull the ribbon wires off to make...

$2.95

IN STOCK

Premium Female/Female Jumper Wires - 20 x 12" (300mm)

PRODUCT ID: 1949

These Female/Female Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12"...

These Female/Female Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" female header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 20-pin ribbon cable. You can always pull the ribbon wires off to...

$3.95

IN STOCK

STEMMA Cable - 150mm/6" Long 4 Pin JST-PH Cable–Female/Female

PRODUCT ID: 3568

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays connected even when moved around, but clicks easy to insert & remove. We...

$0.75

IN STOCK

Premium Male/Male Jumper Wires - 40 x 6" (150mm)

PRODUCT ID: 758

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make...

$3.95

IN STOCK

Premium Male/Male Jumper Wires - 40 x 3" (75mm)

PRODUCT ID: 759

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them...

$3.95

IN STOCK

Premium Female/Male 'Extension' Jumper Wires - 40 x 6" (150mm)

PRODUCT ID: 826

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 40 (4...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires...

$3.95

IN STOCK

Premium Female/Male 'Extension' Jumper Wires - 40 x 3" (75mm)

PRODUCT ID: 825

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are approximately 3" (75mm) long and come in a...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are approximately 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the...

$3.95

IN STOCK

Premium Female/Male 'Extension' Jumper Wires - 40 x 12" (300mm)

PRODUCT ID: 824

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires...

$7.95

IN STOCK

Extra-long break-away 0.1" 16-pin strip male header (5 pieces)

PRODUCT ID: 400

Breakaway header is like the duct tape of electronics, and this header is one better with extra long pins on both sides. This makes it great for...

Breakaway header is like the duct tape of electronics, and this header is one better with extra long pins on both sides. This makes it great for connecting things together that have two sockets - especially solderless breadboards. We also use these with our female-female socket jumpers to create female-male and male-male jumpers! Each pack contains 5 x 16-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1"...

$3.00

IN STOCK

Premium Male/Male Jumper Wires - 40 x 12" (300mm)

PRODUCT ID: 760

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them...

$7.95

IN STOCK

ST-Link STM8/STM32 v2 Programmer & Emulator

PRODUCT ID: 2548

Explore new microcontroller worlds with an ST-Link Programmer & Emulator / Debugging dongle. This little USB stick contains a microcontroller...

Explore new microcontroller worlds with an ST-Link Programmer & Emulator / Debugging dongle. This little USB stick contains a microcontroller with the code for ST's classic programmer/emulator for STM8 and STM32 bit processors. Since STM's are so common, this tool will come in handy whenever you encounter them. You can even get 5V and regulated 3.3V power! Comes with one USB stick and a couple pieces of female-female jumpers. You may...

$12.50

IN STOCK

Microsoft Hackster.io Virtual IoT Pack – w/ Raspberry Pi 3

PRODUCT ID: 3605

In collaboration with Microsoft and Hackster.io, Adafruit's releasing a Virtual IoT pack with boards, sensors, and quite a number of...

In collaboration with Microsoft and Hackster.io, Adafruit's releasing a Virtual IoT pack with boards, sensors, and quite a number of components! This kit is specifically curated for IoT Virtual Bootcamp hosted by Microsoft and Hackster.io in partnership with Adafruit. This kit includes a pre-soldered Adafruit Feather HUZZAH with ESP8266 WiFi and some sensors and components to get you started on your IoT journey. ...

$224.95

7 IN STOCK

DE0-Nano - Altera Cyclone IV FPGA starter board

PRODUCT ID: 451

For every day projects, microcontrollers are low-cost and easy to use. But when you have a project that needs raw power and high speed you may want...

For every day projects, microcontrollers are low-cost and easy to use. But when you have a project that needs raw power and high speed you may want to check out FPGAs (Field Programmable Gate Arrays). FPGAs are like raw chips that you can design by hand. They run very fast and very efficiently. They are designed for mass-parallel execution so they're very good at handling a lot of I/O pins at once, especially for real time video or audio or...

$99.95

48 IN STOCK

Raspberry Pi Arcade Cabinet Pack

PRODUCT ID: 3272

Couldn't get one of those Nintendo Mini Classic consoles? No problem, we've got you covered with this no-solder no-tools required kit! Video...

Couldn't get one of those Nintendo Mini Classic consoles? No problem, we've got you covered with this no-solder no-tools required kit! Video games are one of the most popular applications for the Raspberry Pi (and one of the best gifts to get over the holidays). Play NES, Sega, MAME, SNES, Atari and more! Thanks to the easy-to-use Raspberry Pi and some clever software, you can recreate the classic arcade experience at home. Adafruit will...

$59.95

10 IN STOCK

GoodFET v42 by Travis Goodspeed - v4.2

PRODUCT ID: 1279

The GoodFET is an open-source JTAG adapter, loosely based upon the TI MSP430 FET UIF and EZ430U boards, as described in their documentation. It has...

The GoodFET is an open-source JTAG adapter, loosely based upon the TI MSP430 FET UIF and EZ430U boards, as described in their documentation. It has expanded to be useful as a microcontroller multitool, with 'clients' for programming/debugging MSP430 JTAG, Nordic RF, Chipcon 8051/SPI, AVR, PIC, etc. A handy tool for advanced microcontroller work, and especially for MSP430 fans who want their own JTAG debugger for everyday use. Comes as a...

$49.95

50 IN STOCK

Microsoft Hackster.io Virtual IoT Pack

PRODUCT ID: 3608

In collaboration with Microsoft and Hackster.io, Adafruit's releasing a Virtual IoT pack with boards, sensors, and quite a number of components!...

$189.95

Microsoft Hackster.io Virtual IoT Pack – No Pi

PRODUCT ID: 3604

In collaboration with Microsoft and Hackster.io, Adafruit's releasing a Virtual IoT pack with boards, sensors, and quite a number of...

$189.95

7 IN STOCK

Cupcade: the Raspberry Pi-Powered Micro Arcade Cabinet Kit - v1.0

PRODUCT ID: 1783

Never be bored again with an adorable little arcade cabinet you can fit in your bag! This Raspberry Pi-powered kit combines our sharp PiTFT 2.8"...

Never be bored again with an adorable little arcade cabinet you can fit in your bag! This Raspberry Pi-powered kit combines our sharp PiTFT 2.8" display, mini thumbstick, and mini arcade push buttons and a whole bunch of components to create the most adorable arcade cabinet in the known universe . Comes as a big kit with lots of parts including all electronic components, the laser cut case, power adapter, and a blank SD card (you'll...

$119.95

OUT OF STOCK

Raspberry Pi Zero W

PRODUCT ID: 3400

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! If you didn't think that the Raspberry Pi Zero...

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! If you didn't think that the Raspberry Pi Zero could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero W offers all the benefits of the Pi Zero v1.3, but with one big difference – built-in WiFi! More specifically, this giant upgrade is the addition of a BCM43143 WiFi chip BUILT-IN to...

$10.00

87 IN STOCK

Raspberry Pi Zero W Basic Pack - Includes Pi Zero W

PRODUCT ID: 3409

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! Remember those cereal commercials that would always...

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero W Basic Pack is the barest of essentials that you'll need to get...

$24.50

IN STOCK

Raspberry Pi Zero W Budget Pack - Includes Pi Zero W

PRODUCT ID: 3410

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! Remember those cereal commercials that would always...

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero W Budget Pack is almost everything you need to get going with your...

$34.50

IN STOCK

Raspberry Pi Zero Budget Pack - Includes Pi Zero v1.3

PRODUCT ID: 2817

Note: This does NOT include the new Pi Zero W. This includes the original Pi Zero v1 model, which does NOT include...

Note: This does NOT include the new Pi Zero W. This includes the original Pi Zero v1 model, which does NOT include built-in Bluetooth and WiFi. If you are trying to buy the trendy new Pi Zero W Budget Pack, you are not on the right page! Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero! Remember those cereal commercials that would always say, "part of a...

$29.50

IN STOCK

Great Scott Gadgets HackRF One - Software Defined Radio

PRODUCT ID: 3583

HackRF One from Great Scott Gadgets is a Software Defined Radio peripheral capable of transmission or reception of radio signals from 1 MHz to 6 GHz....

HackRF One from Great Scott Gadgets is a Software Defined Radio peripheral capable of transmission or reception of radio signals from 1 MHz to 6 GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation. Great for listening on RF emitters and transmitting on ISM bands (check your...

$299.95

15 IN STOCK

Raspberry Pi Zero - Version 1.3

PRODUCT ID: 2885

Note: This is NOT the new Pi Zero W. This is the original Pi Zero v1 model, which does not include built-in Bluetooth and WiFi. ...

Note: This is NOT the new Pi Zero W. This is the original Pi Zero v1 model, which does not include built-in Bluetooth and WiFi. If you are trying to buy the trendy new Pi Zero W click here! Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero! At first glance, the Pi Zero isn't much. It just looks like a slimmed down version of the Raspberry Pi we know and love. But...

$5.00

OUT OF STOCK

Stacking Header for Pi A+/B+/Pi 2/Pi 3 - 2x20 Extra Tall Header

PRODUCT ID: 1979

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The...

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The female header part has extra spaces to make it 23mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. The stacky pin part is also extra-long, 10mm, so that when a standard 1.5mm thickness PCB is installed, there will be 8.5mm remaining, plenty to plug into. You'll get...

$2.95

IN STOCK

GPIO Header for RaspberryPi A+/B+/Pi 2/Pi 3 - Tall 2x20 Female Header

PRODUCT ID: 1992

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make...

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 10mm height instead. With 3mm you don't have to cut the really long pins, so its ideal for basic Pi plate design...

$2.95

IN STOCK

Stacking Header for Raspberry Pi - 2x13 Extra Tall

PRODUCT ID: 1112

Stack multiple plates, breakouts etc onto your Raspberry Pi with this custom-made extra-tall and extra-long 2x13 female header. The female header...

Stack multiple plates, breakouts etc onto your Raspberry Pi with this custom-made extra-tall and extra-long 2x13 female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. The stacky pin part is also extra-long, 9.7mm, so that when a standard 1.5mm thickness PCB is installed, there will be 8mm remaining, plenty to plug into. You'll get one header per...

$1.95

IN STOCK

GPIO Header for Raspberry Pi - Extra tall 2x13 Female Header

PRODUCT ID: 1658

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when...

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 9.7mm height instead. With 3mm you don't have to cut the really long pins, so its ideal for basic Pi plate design You'll get one...

$1.75

IN STOCK

GPIO Header for Raspberry Pi A+/B+/Pi 2/Pi 3 - 2x20 Female Header

PRODUCT ID: 2222

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header. The female header part is about 8.5mm tall, good for small...

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 10mm header pins instead. With 3mm you don't have to cut the really long pins, so its ideal for basic Pi HAT design You'll get one header per...

$1.50

IN STOCK

0.1" 2x20-pin Strip Right Angle Female Header

PRODUCT ID: 2823

If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and...

If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip, right-angle female header is a perfect companion piece to our 2x20-pin Dual Male Header. It's a great way to add right-angle capability to a 2x20 pin circuit board either by attaching the right-angle male headers to the board and having a right-angle female...

$1.50

IN STOCK

Adafruit Pi Protector for Raspberry Pi Model Zero

PRODUCT ID: 2883

Now that we're carrying the Pi Zero, PaintYourDragon is back with another gorgeous laser-cut masterpiece. This time he's taken a pass...

Now that we're carrying the Pi Zero, PaintYourDragon is back with another gorgeous laser-cut masterpiece. This time he's taken a pass at a Pi Protector for Raspberry Pi Zero, not quite a full case, it will keep your Pi Zero safe and svelte. Keep your Raspberry Pi® Zero computer tidy and safe in this lovely clear acrylic enclosure. We designed this simple protector to be beautiful, easy to assemble and perfect for...

$4.95

72 IN STOCK

IBM TJBot – A Watson Maker Kit

PRODUCT ID: 3462

Say hello to your new little friend – it might just say "hello" back! Have some fun and code your very own AI robot with TJBot,...

Say hello to your new little friend – it might just say "hello" back! Have some fun and code your very own AI robot with TJBot, a do-it-yourself template to learn, experiment, and explore AI with IBM Watson. The project consists of open-source step-by-step recipes, or coding instructions, designed for a Raspberry PI to help you connect your TJBot to Watson developer services. Want to chat with TJBot or teach it to...

$149.95

33 IN STOCK

Mega protoshield for Arduino

PRODUCT ID: 192

This is an extra large proto-shield, specifically designed for the Mega! It comes with PCB, two buttons and a full set of stacking headers. You can...

This is an extra large proto-shield, specifically designed for the Mega! It comes with PCB, two buttons and a full set of stacking headers. You can stack this shield easily since it comes with extra long female headers The kit includes: 1 x MEGAshield PCB 2 x tactile switch 1 x 3-pin male header 1 x 2x3-pin stacking female header 1 x 10-pin stacking female header 5 x 8-pin stacking female header 1 x 6-pin stacking female header 1 x...

$14.95

IN STOCK

Premium Female/Male 'Extension' Jumper Wires - 20 x 6"

PRODUCT ID: 1954

These Female/Male Extension jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6"...

These Female/Male Extension jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 20-pin...

$1.95

IN STOCK

Premium Female/Male 'Extension' Jumper Wires - 20 x 3"

PRODUCT ID: 1953

These Female/Male 'extension' jumper wires for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3"...

These Female/Male 'extension' jumper wires for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 20-pin ribbon...

$1.95

7 IN STOCK

Premium Female/Male 'Extension' Jumper Wires - 20 x 12"

PRODUCT ID: 1952

These Female/Male 'Extension' Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are...

These Female/Male 'Extension' Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best part is they come in a 20-pin...

$3.95

87 IN STOCK

BNC Female Jack Terminal Block

PRODUCT ID: 2889

One truth about working with test equipment is you always need the cable or adapter you don't have in your toolbox. That's why we...

One truth about working with test equipment is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block BNC (Bayonet Neill–Concelman, for those in the know) connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the BNC Female Jack Terminal Block . BNC connectors are one of the...

$0.95

IN STOCK

Pomona Female 0.1" Socket to Banana Plug - 24" - Black

PRODUCT ID: 2665

We have a couple of these handy Pomona Female 0.1" Socket to Banana Plug 24" cables! Great for use with your benchtop...

We have a couple of these handy Pomona Female 0.1" Socket to Banana Plug 24" cables! Great for use with your benchtop equipment, these are the highest quality cables and will last you years, if not decades. This is the 24" long Black version . We also carry this cable in red. This Female Socket to Banana Plug cable is terrific for prototyping or for use as a jumper on circuit boards, you can shove a ~22AWG solid...

$8.00

53 IN STOCK

Pomona Female 0.1" Socket to Banana Plug - 24" - Red

PRODUCT ID: 2666

We have a couple of these handy Pomona Female 0.1" Socket to Banana Plug 24" cables! Great for use with your benchtop...

We have a couple of these handy Pomona Female 0.1" Socket to Banana Plug 24" cables! Great for use with your benchtop equipment, these are the highest quality cables and will last you years, if not decades. This is the 24" long Red version . We also carry this cable in black. This Female Socket to Banana Plug cable is terrific for prototyping or for use as a jumper on circuit boards, you can shove a ~22AWG solid...

$8.00

48 IN STOCK

Ethernet RJ45 Female Socket Push-Terminal Block

PRODUCT ID: 2912

If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet jack - this adapter will come in very handy! No...

If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet jack - this adapter will come in very handy! No soldering required. Just push the little buttons and slide in your stranded or solid-core wire. Note that these aren't recommended for actual Ethernet traffic, especially long term...but for basic power/data distribution, RJ45's are great! This is the Ethernet (RJ45) Female Jack Push-Terminal...

$5.95

IN STOCK

USB DIY Connector - MicroB Female Plug

PRODUCT ID: 1829

As an addition to our other USB DIY shells, we have a 'micro B female' in a panel-mount-like connector. This isn't true panel mount but...

As an addition to our other USB DIY shells, we have a 'micro B female' in a panel-mount-like connector. This isn't true panel mount but you could glue the black plastic shell into your project and then press-fit in the micro B connector. The 5-pins are much easier to solder than a surface mount connector We have other DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a...

$0.95

IN STOCK

2mm Pitch 25-Pin Female Socket Headers - Pack of 5

PRODUCT ID: 2672

Never get frustrated with 2mm-pitch modules again! Each one of these 25-pin female socket header packs contains 5 pieces of 25-pin, 2mm pitch...

Never get frustrated with 2mm-pitch modules again! Each one of these 25-pin female socket header packs contains 5 pieces of 25-pin, 2mm pitch headers. Great for when you need to connect to something with 2mm pitch. Stack these headers side by side or break them apart to receive your desired length. They are even gold plated to ensure longevity without oxidation. They are not break-apart but you can cut them with diagonal...

$3.95

IN STOCK

RCA (Composite Video, Audio) Female Jack Terminal Block

PRODUCT ID: 2793

One truth about working with A/V is you always need the cable or adapter you don't have in your toolbox. That's why we love these...

One truth about working with A/V is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block RCA connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the RCA (Composite Video, Audio) Female Jack Terminal Block . RCA is one of the most common A/V connectors. We also have a (matching) RCA Male Plug...

$2.50

IN STOCK

36-pin 0.1" Female header - pack of 5!

PRODUCT ID: 598

Female header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards, sockets for wires or...

Female header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains five 36-pin long headers, 0.1" pitch. They're even gold plated so they wont oxidize! You can cut these down to different sizes fairly...

$2.95

IN STOCK

36-pin 0.1" Short Female Header - Pack of 5

PRODUCT ID: 3008

In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains five 36-pin short...

In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains five 36-pin short female headers, 0.1" pitch. These headers are very short for fitting into tight spaces with a height of just 5mm instead of the 'standard' 8mm. Female headers are like the duct tape of electronics. They're great for connecting things together, soldering to perf-boards, sockets for...

$7.95

IN STOCK

Feather Stacking Headers - 12-pin and 16-pin female headers

PRODUCT ID: 2830

These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do?...

These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do? They stack. Put the headers through your Feather and then you can not only plug them into a solderless breadboard, but you could attach circuitry on top as well Note : Comes with one 12-pin and one 16-pin header, Feathers not included

$1.25

IN STOCK

Feather Header Kit - 12-pin and 16-pin Female Header Set

PRODUCT ID: 2886

These two Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!...

These two Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do? They get soldered on either side of the Feather board. Now you can plug in FeatherWings to add more capability to your portable project. Unlike our Feather Stacking Headers, they aren't designed to 'stack', but they're more compact. Note: Comes with one 12-pin and...

$0.95

IN STOCK

GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

PRODUCT ID: 2243

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the through-hole...

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the through-hole version of the SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header. This header is for super-slim through-hole designs. It's a custom-made, 2x20 short female header that can be used to plug a Raspberry Pi HAT onto a B+, A+, or Pi 2. It's...

$1.95

IN STOCK

Short Feather Headers Kit - 12-pin and 16-pin Female Header Set

PRODUCT ID: 2940

These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're...

These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Feather project takes up, but still maintain that flexible configuration. "Normal" socket headers have an 8.5mm body height so this...

$1.50

IN STOCK

USB OTG Host Cable - MicroB OTG male to A female

PRODUCT ID: 1099

This cable looks like a USB micro cable but it isn't! Instead of a USB A Plug, it has a USB A Socket on the end. This cable is designed for use...

This cable looks like a USB micro cable but it isn't! Instead of a USB A Plug, it has a USB A Socket on the end. This cable is designed for use with OTG (On the Go) host devices (like the Arduino Due or many tablets) so you can connect a mouse, keyboard, or any other USB device. You'll still need to have drivers on the device, this cable is just a cable and contains no microcontroller or electronics inside. Approximately 6" long...

$2.50

IN STOCK

SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

PRODUCT ID: 2187

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's...

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's harder to use than the Thru-Hole type headers, but for the slickest, slimmest fit, this header is recommended!

$1.95

IN STOCK

0.1" 36-pin Strip Right-Angle Female/Socket Header (5 pack)

PRODUCT ID: 1542

Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow...

Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow 22AWG wire or male header to connect, etc. We go through these gals real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains 5 x right angle female 36-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1" grid. They aren't...

$4.95

51 IN STOCK

0.1" 2x36-pin Strip Straight Socket (Female) Header (5 pack)

PRODUCT ID: 1544

Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow...

Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow 22AWG wire or male header to connect, etc. We go through these gals real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains 5 x dual row female 36-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1" grid. They...

$5.95

IN STOCK

Right Angle Extension USB Cable - A Male to A Female - 1 meter / 39" long

PRODUCT ID: 3419

This here is a handy A male to A female USB extension cable. This handy USB extension cable will make it easy for you to extend your USB cable...

This here is a handy A male to A female USB extension cable. This handy USB extension cable will make it easy for you to extend your USB cable when it won't reach, but with a twist - literally! Instead of the cable coming straight out from the connector, there's a right angle bend on the male end. We use these handy cables all over our factory and homes. Cable is standard "Adafruit black". Approximately 1 meter / 3...

$2.95

IN STOCK

0.1" 2x36-pin Strip Right-Angle Socket (Female) Header (5 pack)

PRODUCT ID: 1543

Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow...

Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow 22AWG wire or male header to connect, etc. We go through these gals real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains 5 x dual-row right angle female 36-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1"...

$7.95

100 IN STOCK

Panel Mount Extension USB Cable - Micro B Male to Micro B Female

PRODUCT ID: 3258

Check out this handy MicroUSB extension cable, which will make it easy for you to enclose a device that has a B type (micro USB host) port....

Check out this handy MicroUSB extension cable, which will make it easy for you to enclose a device that has a B type (micro USB host) port. Great if you need to extend the USB port for your Raspberry Pi, Arduino, Feather or really anything development board. This Micro-B male/female extension cable features a male USB Micro-B plug on one end, and a bulkhead mountable Micro-B female receptacle on the other. The jack half has two...

$4.95

IN STOCK

Panel Mount Extension USB Cable - Mini B Male to Mini B Female

PRODUCT ID: 3318

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be...

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, BeagleBone, or any other Mini-B device into a box! This Mini-B male/female extension cable features a male USB Mini-B plug on one end, and a bulkhead mountable Mini-B female receptacle on the other. The jack half has two mounting...

$4.95

IN STOCK

GPIO Stacking Header for Pi A+/B+/Pi 2/Pi 3 - Extra-long 2x20 Pins

PRODUCT ID: 2223

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins. The female header part...

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra long 10mm pins, compared with our plain version which is the same base height but has 3mm header pins instead. With 10mm you can have a HAT that has extra pins to stack another HAT on top!...

$2.50

IN STOCK

Short Feather Male Headers - 12-pin and 16-pin Male Header Set

PRODUCT ID: 3002

These two Short Male Headers alone are, well, lonely. But pair them with any of our Feather boards and you're...

These two Short Male Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and tiny and are designed to match perfectly with our shorty female header kit for Featherwings. Note that you could use normal header with those headers but these are short and dont need clipping. By using both you can get a 3.5mm slimmer Feather+Wing...

$0.50

IN STOCK

JST 2-pin Extension Cable with On/Off Switch - JST PH2

PRODUCT ID: 3064

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin...

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers! One end has a classic female JST-PH2 socket, and the other end...

$2.95

IN STOCK

36-pin Stacking header - pack of 5!

PRODUCT ID: 3366

Headers are like the duct tape of electronics. They're great for connecting things together, soldering to perf-boards, sockets for wires or...

Headers are like the duct tape of electronics. They're great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of five! Stacking headers are a twist on the standard/common male and female header sets. In this case you have one header that has a socket on one end, and a long...

$2.95

IN STOCK

GPIO Hammer Headers - Solderless Raspberry Pi Connectors - Male + Female + Installation Jig

PRODUCT ID: 3413

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. They come in both male and female, and use crafty little retaining nubbins to grip tightly into the holes on the PCB. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to...

$6.50

OUT OF STOCK

Stacking Header Set for Beagle Bone Capes (2x23)

PRODUCT ID: 706

Stack to the max with our Beagle Bone Proto Cape using these ingenious stacking headers. They're just like 2x23 0.1" spaced female headers...

Stack to the max with our Beagle Bone Proto Cape using these ingenious stacking headers. They're just like 2x23 0.1" spaced female headers but with a twist! The 'legs' are extra-long so you can solder it -through- a PCB and plug it into the Bone. You can stack as many as you'd like, for modular design. Neat, right? Each package comes with two pieces of 2x23 header so you only need one per Proto Cape kit. The Proto Cape is...

$4.95

IN STOCK

FeatherWing Doubler - Prototyping Add-on For All Feather Boards

PRODUCT ID: 2890

This is the FeatherWing Doubler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are...

This is the FeatherWing Doubler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are two! The magic of the Doubler comes when stacking a Feather and another board on top of the Doubler so you can work with both boards simultaneously side-by-side! In addition to the board the Doubler comes with: 1 Doubler PCB1 set Feather Stacking Headers1 set Feather Female Headers The...

$7.50

IN STOCK

Pimoroni Zero LiPo

PRODUCT ID: 3196

Having a discrete, slick, and tidy power supply is always tricky when taking a project on the go...but get ready to roam the earth worry free with...

Having a discrete, slick, and tidy power supply is always tricky when taking a project on the go...but get ready to roam the earth worry free with the tiny little Pimoroni Zero LiPo ! It aims to give you the most compact power supply possible for all versions of Raspberry Pi. You can either solder the 0.8mm thick PCB directly to the bottom of your GPIO header for a permanent solution or solder on the provided 2x4 0.1" female...

$9.95

IN STOCK

Microsoft IoT Pack for Raspberry Pi 3 - w/ Raspberry Pi 3

PRODUCT ID: 2733

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an...

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an IoT enabled device. A collaboration between Microsoft's IoT division and Adafruit, this pack's the best way to get started using both Windows 10 on your Pi and to start doing some popular projects with the internet of things. Check...

$114.95

IN STOCK

FeatherWing Tripler Mini Kit - Prototyping Add-on For Feathers

PRODUCT ID: 3417

This is the FeatherWing Tripler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are...

This is the FeatherWing Tripler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are three! The magic of the Tripler comes when you want to connect your Feather to two other Feather Wings without needing any stacking headers! The Tripler comes with: 1 Tripler Wing PCB3 sets Feather Female Headers The Tripler, like the Proto, has three breakouts for each pin on a Feather, as well...

$8.50

IN STOCK

Pimoroni Button SHIM for Raspberry Pi

PRODUCT ID: 3582

Pimoroni's Button SHIM gives you five handy, physical buttons and an RGB status LED, and it's HAT and pHAT-compatible!...

Pimoroni's Button SHIM gives you five handy, physical buttons and an RGB status LED, and it's HAT and pHAT-compatible! Pimoroni's SHIM-format boards are designed to slip neatly onto your Pi's GPIO pins and still allow you to use HATs and pHATs at the same time. Or solder the included female header onto Button SHIM and use it as a standalone board. The buttons and status LED stick out from the top edge of your...

$6.95

10 IN STOCK

Raspberry Pi Zero W Starter Pack - Includes Pi Zero W

PRODUCT ID: 3411

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! Remember those cereal commercials that would always...

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W! Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero W Starter Pack is everything you need to get going with your...

$59.95

IN STOCK

Pi-EzConnect Terminal Block Breakout HAT

PRODUCT ID: 2711

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has...

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry PiMini proto area for adding componentsAdd standard male or female headers for breadboard like functionalityPower (both 5V and 3.3V) as well as ground connections...

$19.95

IN STOCK

Microsoft IoT Pack for Raspberry Pi 3 - No Pi

PRODUCT ID: 2702

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an IoT...

$75.00

IN STOCK

Pimoroni Speaker pHAT for Raspberry Pi Zero

PRODUCT ID: 3401

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little...

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little pHAT. It's the neatest way to add audio to your Pi project, and its beautiful artwork evokes an 80s boombox! Pimoroni isn't claiming audiophile sound quality, but it's perfect for fun little projects where you want to add sound output – speech, notification sounds, or light...

$12.95

68 IN STOCK

MicroPython pyboard Anodized Housing with Open Lid

PRODUCT ID: 3496

The pyboard housing is a beautiful and robust enclosure for all versions of the pyboard. It is made out of machined aluminum which is then anodized...

The pyboard housing is a beautiful and robust enclosure for all versions of the pyboard. It is made out of machined aluminum which is then anodized to give it gorgeous light blue color, and laser-engraved to add labels. This variation has an open lid to allow access to female header pins on the top of the pyboard, so its perfect for hacking! If you have a pyboard with female header pins soldered in, you can buy this housing for it and all the...

$39.95

95 IN STOCK

Pimoroni Pirate Radio - Pi Zero W Project Kit

PRODUCT ID: 3477

Build your very own internet-connected radio with Pimoroni's Pirate Radio Kit! This kit has just-about-everything you'll...

Build your very own internet-connected radio with Pimoroni's Pirate Radio Kit! This kit has just-about-everything you'll need: Pimoroni's flashy new pHAT BEAT DAC and stereo amp, a 5W speaker, and a beautifully retro acrylic enclosure to make it look the business. It even includes a Pi Zero W. All you need is to add your own micro-SD card and USB power supply. It'll take you around 30...

$49.95

34 IN STOCK

Particle Maker Kit with Photon

PRODUCT ID: 2798

The Particle Maker Kit has just about everything you need to get started with your Particle Photon. It's the kind of no nonsense...

The Particle Maker Kit has just about everything you need to get started with your Particle Photon. It's the kind of no nonsense starter kit that's filled with all the components and accessories you need to build simple internet enabled projects and up your hacker level from zero to hardware hero. This kit also includes a pretty nifty carrying case that you can tidy up your projects with and keep displayed on your...

$89.00

2 IN STOCK

Pimoroni Scroll Bot - Pi Zero W Project Kit

PRODUCT ID: 3479

A robot friend to sit on your desk and scroll the news, weather, or your Twitter feed - it's the Pimoroni Scroll Bot! The Scroll Bot...

A robot friend to sit on your desk and scroll the news, weather, or your Twitter feed - it's the Pimoroni Scroll Bot! The Scroll Bot Kit combines the Pi Zero W with the new Scroll pHAT HD board, and masquerades as a friendly orange robot, perfect for sitting on your desk or on a shelf. It's ideal for scrolling messages or for simple animations and, of course, it takes advantage of the built-in wireless LAN on the Pi...

$44.95

21 IN STOCK

Pimoroni Explorer pHAT for Raspberry Pi Zero

PRODUCT ID: 3018

The Explorer pHAT is the perfect prototyping side-kick for your Raspberry Pi. Based on Pimoroni's popular Explorer Hat Pro, this...

The Explorer pHAT is the perfect prototyping side-kick for your Raspberry Pi. Based on Pimoroni's popular Explorer Hat Pro, this is a smaller cheaper version designed to fit perfectly on a Raspberry Pi Zero! A heap of useful input and output options have been added that will take your projects to the next level. Great for driving motors, using analog sensors, and interfacing with 5V sensors & systems Though...

$12.50

27 IN STOCK

Pimoroni Mood Light - Pi Zero W Project Kit

PRODUCT ID: 3478

Our Pimoroni pals have curated a beautifully modern Mood Light Kit that'll look great on your bedside table, bookcase, or...

Our Pimoroni pals have curated a beautifully modern Mood Light Kit that'll look great on your bedside table, bookcase, or desk. It's even internet-connected! This kit has just-about-everything you'll need: Pimoroni's Unicorn pHAT board with 32 programmable RGB Neopixel LEDs, diffuser, power adapter, and a beautifully acrylic enclosure to make it look like a lamps. It even includes a Pi...

$39.95

35 IN STOCK

Raspberry Pi Zero Starter Pack - Includes Pi Zero v1.3

PRODUCT ID: 2816

Note: This does NOT include the new Pi Zero W. This includes the original Pi Zero v1 model, which does NOT include...

Note: This does NOT include the new Pi Zero W. This includes the original Pi Zero v1 model, which does NOT include built-in Bluetooth and WiFi. If you are trying to buy the trendy new Pi Zero W Starter Pack, you are not on the right page. Due to popular demand, there might be some delay in shipping products containing Pi Zero! Remember those cereal commercials that would always say, "part of a...

$54.95

IN STOCK

Microsoft IoT Pack for Raspberry Pi 3

PRODUCT ID: 2737

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an IoT...

$114.95

University of Virginia - Web and Mobile Systems Pack

PRODUCT ID: 2152

This is a custom made pack for the University of Virginia. It contains all the gear needed for Web and Mobile Systems class - CS4720....

This is a custom made pack for the University of Virginia. It contains all the gear needed for Web and Mobile Systems class - CS4720. Since it's a pretty cool pack, and seems like a great course, we've decided to also sell it in our store. Here's a description of the course to get an idea of what they're working on and check out the class website for more information. Our course mixes web technologies with mobile...

$114.95

OUT OF STOCK

Bluefruit EZ-Link - Bluetooth Serial Link & Arduino Programmer - v1.3

PRODUCT ID: 1588

Note: This product is currently undergoing a revision and will be available again soon! We are excited to add another product to our growing...

Note: This product is currently undergoing a revision and will be available again soon! We are excited to add another product to our growing Adafruit Bluefruit line, this time it's the Bluefruit EZ-Link: the best Bluetooth Serial Link device ever made. Like you, we have purchased all sorts of Bluetooth serial link modules, with high expectations - we just wanted something that worked! But nothing ever did exactly what we wanted: there...

$22.50

OUT OF STOCK

USB DIY Slim Connector Shell - USB Type A Socket/Female

PRODUCT ID: 1828

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside This is the 'slim' version of the DIY...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside This is the 'slim' version of the DIY USB-A Female connector. It's a little more elegant because instead of snapping two pieces together the connector press-fits into the overmolding for a modern look. We also carry the slim size in USB-A male, miniB plug, microB male and USB-microB female. Normal DIY "USB shells" are...

$0.95

DISCONTINUED

Extra-tall SMT GPIO Header for Raspberry Pi HAT - 2x20 Extra Tall Female Header

PRODUCT ID: 2714

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female...

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female header. This header allows you to plug your Raspberry Pi HAT onto a Raspberry Pi A+, B+ or Pi 2. We also carry various through-hole versions but this is for when you really need to have all the space available, such as on our 3.5" PiTFT

$2.95

DISCONTINUED

SEARCH RESULTS FOR: female female

PRODUCTS: