Internet of Things - IoT / Ethernet

This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. We think this would be most useful when putting a Beagle Bone, Raspberry Pi, Arduino Ethernet into a box. The jack half has two mounting 'ears' with 4-40 screws installed, 1" inch / 25mm apart. The ears are flexible so the holes don't have to drilled very precisely. Can be used with box walls up to 0.25" wide. The...

The Raspberry Pi 3 Model B is the most popular Raspberry Pi computer made, and the Pi Foundation knows you can always make a good thing better ! And what could make the Pi 3 better? How about a  faster processor, 5 GHz WiFi, and updated Ethernet chip with PoE capability? Good guess - that's exactly what they did! The Raspberry Pi 3 Model B+ is the latest product in the Raspberry Pi 3 range, boasting an updated 64-bit quad core...

If you liked the BeagleBone Black Rev B, you will love the Rev C! The Rev C has a blistering 1GHz AM3358 processor and 512MB onboard DDR3 RAM, two 46-pin headers, micro HDMI for audio/video output, USB ports, 10/100 Ethernet and other I/O features. The Rev C is an ultra-powered embedded computer that can fit in a mint tin. This model includes 4GB of eMMC built-in storage instead of the Rev B's 2GB. With the doubled storage and faster eMMC,...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible with Raspberry Pi 3 B+ that has PoE pins and Raspberry Pi 4. For people with neither Pi 3 B+'s...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different lines for non-PoE devices. This is an economical, practical,...

Wireless is wonderful, but sometimes you want the strong reliability of a wire. If your Feather board is going to be part of a permanent installation, this Ethernet FeatherWing will let you add quick and easy wired Internet. Just plug in a standard ethernet cable, and run the Ethernet2 library for cross-platform networking. Works with all/any of our Feather boards as an Ethernet Client (server not supported at this time)! Ethernet is a...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device,  even if it doesn't natively support PoE!  The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different lines for non-PoE devices. This is an...

Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a mess of wires. There is an official Power-over-Ethernet standard that allows devices and routers to activate a 48VDC power line on the unused Ethernet pins (4,5 and 7,8) but PoE is...

This three-in-one Particle Ethernet Feather is a mix of our Ethernet 'wing and the Tripler 'wing. The form-factor is based around the Adafruit FeatherWing Tripler. The two side connectors allow you to plug in one Particle Mesh device along with a Feather accessory. The Ethernet FeatherWing is deisgned to be the fastest way to add wired connectivity to your Argon, Boron, or Xenon and turns any Particle Mesh dev kit into an Ethernet...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one cable, and then separates the data (Ethernet) and power (+12VDC regulated) into two different lines for non-PoE devices. This is an economical, practical,...

The W5500 Ethernet Shield for Arduino from Seeed Studio is a great way to set up your projects with internet connectivity with just a single chip.  Similar to the Arduino Ethernet Shield, but with a newer chipset, this ethernet shield supports both TCP and IP Protocols in TCP, UDP, ICMP, IPv4, ARP, IGMP, and PPoE format.  The RJ45 ethernet port is also low enough so you can stack another shield on top of it The board includes...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one cable, and then separates the data (Ethernet) and power (+12VDC regulated) into two different lines for non-PoE devices. This is an economical, practical,...

The Raspberry Pi 4 Model B is the newest Raspberry Pi computer made, and the Pi Foundation knows you can always make a good thing better ! And what could make the Pi 4 better than the 3? How about a  faster processor, USB 3.0 ports, and updated Gigabit Ethernet chip with PoE capability? Good guess - that's exactly what they did! The  Raspberry Pi 4  is the latest product in the Raspberry Pi range, boasting an...

Coming soon! Sign up to be notified when we get these in the store! Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible with Raspberry Pi 3 B+ that has PoE...