Batteries / Battery Holders

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds one 20mm coin cell (also known as CR2032) in series to generate 3V nominal. 20mm coin cells are popular as they are used in keychain lights and remotes, so they are easy to get and fairly low cost. They tend to have about 220mAh capacity. The holder is made of plastic and...

Make a nice portable power pack with this 4 x AA battery holder. It fits any alkaline or rechargeable AA batteries in series. There's a snap on cover and an on/off switch which can be handy when wiring to something without a switch. New! We now have 0.1" headers on ends of these cables so you can plug them into a breadboard or headers with ease! Of course, you can...

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is slim, and 3 AAA's add up to about 3.3-4.5V, a very similar range to Lithium Ion/polymer (Li-Ion) batteries and have an on-off switch. That makes them ideal for use with 3.3V projects that have a 2-pin JST connector meant for one...

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 or CR2032 are the most popular size) in series to generate 6V nominal. (If you want only 3V, we suggest sticking a crumpled piece of tin foil in one of the slots.) 20mm coin cells are popular as they are used in keychain lights, so they are easy to...

A simple 2-pin connector that is compatible with the "JST PH 2-pin" connector - perfect for soldering to the bottom of our 3.3V Logic Trinket and 5V Logic Trinket! These mate perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector. Note: This...

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. Comes with one fully assembled and tested coin cell battery holder and a small stick of 0.1" header so...

We've got battery holders for all sorts of needs and projects! Waterproof? Here ya go. With an on/off switch? Easy peasy. Here's our latest addition in classy Adafruit black: 4 x AA Battery Holder with Premium Header Wires. What's so special about 'em? Well you can plug them right into a breadboard! No need to fight with those skinny stripped wires you normally get....

This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm center-positive barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box! Battery & screw not included.

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds one 20mm coin cell (CR2032 is the most popular size) to generate 3V nominal. 20mm coin cells are popular as they are used in keychain lights and remotes and other small topys, so they are easy to get and fairly low cost. And speaking of lights, these battery holder includes...

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. There's two ground pins, one 'switched' power pin, and one pin that is always on....

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector.

We've got battery holders for all sorts of needs and projects! Waterproof? Here ya go. With an on/off switch? Easy peasy. Here's our latest addition in classy Adafruit black: 2 x AA Battery Holder with Premium Header Wires. What's so special about 'em? Well you can plug them right into a breadboard! No need to fight with those skinny stripped wires you normally get....

We've got battery holders for all sorts of needs and projects! Waterproof? Here ya go. With a clicky on/off switch? Easy peasy. Here's our latest addition in classy Adafruit black: 2 x AA Battery Holder with Knife Switch. What's so special about 'em? Well with the knife switch you can easily control the flow of electricity to your project. While there are many...

This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There's two ground pins, one 'switched' power pin, and one pin that is always on. This is compatible with the "JST PH 2-pin" connectors we use...

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. Comes with one fully assembled and tested coin cell battery holder and a small stick of 0.1" header so you can...

Here's yet another addition to our family of AA battery holders. It's a holder for five (5) AA batteries, with 5" wire leads. It's black and has a 2.1mm barrel plug (tip positive). 5 x AA battery packs are best used with Arduino-compatibles and other dev boards with 2.1mm DC jacks and a 5V regulator, because 5V regulators tend to like 1-2V of overhead. 4 x AA battery...

Make a portable power brick with plenty of juice! Use Alkaline AA's for a 9V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 7.5V supply. Either one is good for running electronics that have a 5V voltage regulator (thus requiring a 7V+ supply). Will last about 10 times longer than a 9V Plug is 5.5mm outer diameter, 2.1mm inner diameter, center positive....

This adorable little coin cell battery holder is great for small, portable, or wearable projects. It holds two 20mm coin cell batteries (also known as CR2032) in series to generate 6V nominal. 20mm coin cells are popular as they are used in keychain lights and remotes, so they are easy to get and fairly low-cost. They tend to have about 220mAh capacity. The housing...

Here's another addition to our growing family of AA battery holders. A holder for four (4) AA batteries! It's got an 8" long power cable with a 2.1mm DC jack at the end, and, oh yes, it's in classy Adafruit black. 4 x AA battery packs are best used with development boards with 2.1mm DC jacks and can run with ~4.8V (4 x NiMH) to ~6V (4 x Alkaline). Great for powering...

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. There's two ground pins, one 'switched' power pin, and one pin that is always on. Comes with...

Make a portable power brick with plenty of juice! Use Alkaline AA's for a 12V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 9.6V supply. Either one is good for running electronics that have a 5V voltage regulator (thus requiring a 7V+ supply) or perhaps some motors or solenoids. Perfect for portable Arduinos, motors, solenoids, 12V LED strips, etc. An...

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the...

Here's another addition to our growing family of AA battery holders. A holder for three (3) AA batteries! It's got an 8" long power cable with a 2.1mm DC jack at the end, and, oh yes, it's in classy Adafruit black. This battery holder connects 3 AA batteries together for powering all kinds of projects. Three AA's add up to about 3.6-4.5V, a very similar range to...

We've got battery holders for all sorts of needs and projects! Waterproof? Here ya go. With an on/off switch? Easy peasy. Here's our latest addition: 2x2 AA Battery Holder with Premium Header Wires. What's so special about 'em? Well besides being a nice compact cubic shape, you can plug the wires right into a breadboard! No need to fight with those skinny stripped...

When you need a portable 12V power pack, this big holder will do the job! The holder will store 8 AA batteries end to end, to give approximately 12VDC output with up to 2 amp peak current draw. We like this configuration in particular because it holds the batteries securely, even if being bumped/moved around. This would make a good power source for EL panels, 12V...

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (negative) and the other tab is +3 Volts. This holder is meant to be used with Lithium CR2032...

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the...

This is an interesting kind of battery holder, usually you'll see ones that are designed for holding like AAA's or something. This battery holder is designed to clip into and hold camcorder batteries. Specifically, the common SONY NP-Fxx series of batteries and compatibles, made with cylindrical LiIon cells and 7.4v nominal output. By clipping a battery in, you can...

This is an interesting kind of battery holder, usually you'll see ones that are designed for holding like AAA's or something. This battery holder is designed to clip into and hold camcorder batteries. Specifically, the Panasonic CGR-D28 (7.4V, 3300mAh) and CGA-D54s (7.2V, 5400mAh) Lithium-Ion Battery Packs. We also have a holder for the SONY NP-Fxx series and Canon...

I found these high-quality battery clips. They're molded plastic so they won't tear like cheap clips, and they cover the battery terminals to prevent shorts. Comes with a 5.5mm/2.1mm center-positive barrel connector, assembled! Battery not included.

This is an interesting kind of battery holder, usually you'll see ones that are designed for holding like AAA's or something. This battery holder is designed to clip into and hold camcorder batteries. Specifically, the common Canon LP-E6 rechargeable Lithium-Ion Battery Pack (7.2V, 1800mAh). We also have a holder for the SONY NP-Fxx series and Pansonic...