Power / Connectors & Adapters / JST

These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors...

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together! This is an A-A cable, that...

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or...

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This cable is a little over 100mm / 4" long and fitted with JST-GH compatible 6-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily, and the wires are even color coded! These would go great with SEN54 or SEN55 all-in-one air quality sensor modules from Sensirion For more...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has header pins, so it could be used to connect to socket...

If you're a DIY enthusiast who likes to micro-manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. This connector can be used with Qwiic boards and cables, to easily connect...

A simple 2-pin connector that is compatible with the "JST PH 2-pin" connector - perfect for soldering to the bottom of our 3.3V Logic Trinket and 5V Logic Trinket! These mate perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector. Note: This...

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers!...

This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND. Red for V+. White for SDA. Green for SCL. Even though this is a JST PH connector, it will fit into a Seeed Grove connector and...

If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin connector, this cable will do the trick. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the other. Note that the colors we got are somewhat matchy with our '2mm PH' sized STEMMA...

If you'd like to make a connection to a board or breakout with Seeed Grove connection, this 100mm long 4-wire cable is fitted with a Grove connector and four bare wires. Please note you will have to watch for voltages on the power/signal pin when using 3V-only sensors, because Grove boards that are 5V logic like many Arduino UNO-compatibles. The colors are: Black for...

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector.

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector which are compatible with the JST PH 4 pin. These are the horizontal style. You can use these with any of our JST PH 4-Pin compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH compatible)....

Totally 220 pieces, this 2.0mm Pitch Kit with JST-PH Connectors is a must-have for your workstation. You'll have enough sockets and plugs to fuel your maker tendencies for days on end! These connectors are really common in electronics, we use the 2 pin ones for our batteries and battery packs. The 3 pin and 4 pin are used for STEMMA connectors. The 4 pin size is even...

If you're a DIY enthusiast who likes to micro-manage your project's connections, here is a 10-pack of some micro 1mm pitch connectors that are JST SH compatible! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. These connectors can be used with Qwiic boards...

By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in...

If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin connector, this cable will do the trick. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug connectors on the other. Note that the colors we got are somewhat matchy with our '2mm PH' sized STEMMA cables,...

Totaling 560 pieces, this 2.5mm Connector Kit with JST-XH Compatible Connectors is a must-have for your workstation. You'll have enough sockets and headers to fuel your maker tendencies for days on end! These connectors are really common in electronics, we use the 2 pin ones for our arcade quick-connects. Since they are 2.5mm they are very close to and will fit 0.1"...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - which are compatible with the JST PH 4 pin. These are the vertical style. You can use these with any of our JST PH 4-Pin compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH compatibles)....

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector which are compatible with the JST PH 3 pin. These are the horizontal style. You can use these with any of our JST PH 3-Pin compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). We also carry...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector which are compatible with the JST PH 3 pin. These are the vertical style. You can use these with any JST PH 3-Pin or Compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH compatibles). We also...

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards. We use these mostly for EL wire. This is the same connector as is on the inverter. It's useful if you're making a...

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards. This is the matching connector to the inverter. It is required to connect EL wire to the inverter! 0.1" (2.54mm) pitch...