Breakout Boards / WiFi

This 4" / 100mm long flexible uFL 2.4GHz antenna has approx 4DBi gain and a 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless receiver/transmitter such as the Adafruit CC3000s! Antenna comes with a uFL (a.k.a u.FL / IPX / IPEX) connector, so no more need for additional adapters to get your IoT cloud flying high!

This 8"/200mm long swivel dipole antenna has 5dBi of gain and 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless receiver/transmitter such as: 2.4GHz Wi-Fi (802.11b/g/n). 2.4GHz XBee. Bluetooth®. Other 2.4GHz transceivers. Antenna comes with the industry standard RP-SMA connector that is found on nearly all WiFi devices. If...

This 4"/100mm long swivel dipole antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless receiver/transmitter such as: 2.4GHz Wi-Fi (802.11b/g/n). 2.4GHz XBee. Bluetooth®. Other 2.4GHz transceivers. Antenna comes with the industry standard RP-SMA connector that is found on nearly all WiFi devices. If...

Give your Feather project a lift with the Adafruit AirLift FeatherWing - a FeatherWing that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite Feather (like the Feather M4) that comes with its own set of awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a best friend, the ESP32....

Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! The ESP8266 processor from Espressif is an 80 MHz microcontroller with a full WiFi front-end (both as client and access point) and TCP/IP stack with DNS support as well. While this chip has been very popular, its also been very difficult to use. Most of the low...

Give your plain ol' microcontroller project a lift with the Adafruit AirLift - a breakout board that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite microcontroller (like the ATmega328 or ATSAMD51), awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a best friend, the ESP32....

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. It's an...

Give your Arduino project a lift with the Adafruit AirLift Shield - a shield that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite Arduino-compatible (like the Metro M4 or the classic Metro 328) that comes with its own set of awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a...

Connect your Arduino to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work, so we...

Squeeeeze down your next ESP32 project to its bare-bones essential with the Adafruit HUZZAH32 Breakout. This breakout is basically the 'big sister' of our HUZZAH 8266, but instead of an ESP8266 it has the '32! We've pared down our popular Feather ESP32, removing the battery charger and USB-serial converter. You just get a regulator, some protection diodes, two...

Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer...

Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer...

Connect your Arduino to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work, so we...

Give your ItsyBitsy project a lift with the Adafruit AirLift Bitsy Add-On - a daughterboard that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite ItsyBitsy (like the Itsy' M4) that comes with its own set of awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a best friend, the...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an...

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an...

This interesting module is a lot of fun for hobbyists and students who are interested in experimenting with the ESP8266 WiFi chipset. We bought a bunch of these modules, updated the firmware to the much-easier-to-use v0.924 and wrote some Arduino code to grab a webpage. We do not have a detailed tutorial at this time, this chipset/module is for the curious and...

ESP32-S2 Saola-1 is a small-sized ESP32-S2 based development board produced by Espressif. Just about all of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2 Saola-1 on a breadboard - we recommend two breadboards 'side-by-side' since the Saola is a bit wide...

Quantify the world! The Sensor Kit from Particle is a curated mix of awesome sensors and electrical components specifically selected by the engineers on the Particle Team. If you want to measure temperature, sense loudness, measure distances, capture motion, or detect noxious gases, the Sensor Kit has you covered. Whether you’re building a connected robot or...

Quantify the world! The Sensor Kit from Particle is a curated mix of awesome sensors and electrical components specifically selected by the engineers on the Particle Team. If you want to measure temperature, sense loudness, measure distances, capture motion, or detect noxious gases, the Sensor Kit has you covered. Whether you’re building a connected robot or...

Discontinued - you can grab the Adafruit ESP32 Feather V2 - 8MB Flash + 2 MB PSRAM - STEMMA QT instead! Woohoo, it's time for a Particle Mesh party! And the Particle Argon is bringing it with a mix of Bluetooth Low Energy and Wi-Fi, your two most favorite 2.4GHz wireless protocols. The Argon is a powerful Wi-Fi enabled development kit that can act as either a...

Discontinued - you can grab Particle Argon Kit - nRF52840 with Bluetooth® Low Energy and WiFi instead! Warning: Particle is deprecating a Xenon / Mesh support. With a little effort these boards can be converted/reprogrammed and make for great little CircuitPython or Arduino-compatible boards, and but they will no longer be supported by the Particle Cloud service....

Woohoo, it's time for a Particle Mesh party! And the Particle Argon is bringing it with a mix of Mesh networking and and Wi-Fi, your two most favorite 2.4GHz wireless protocols. The Argon is a powerful Wi-Fi enabled development kit that can act as either a standalone Wi-Fi endpoint or Wi-Fi enabled gateway for Particle Mesh networks. It is based on the Nordic...

As of January 17, 2023 - the Boron LTE is now powered by EtherSIM, Particle's new globally available, self-optimizing SIM with no data plans or device fees. Particle's Free Plan supports up to 100 devices, cellular data, and fully-featured platform access with no time limit. Woohoo, it's time for a Particle Mesh party! And the Particle Boron LTE is bringing it with a...

Warning: Particle is deprecating a Xenon / Mesh support. With a little effort these boards can be converted/reprogrammed and make for great little CircuitPython or Arduino-compatible boards, and but they will no longer be supported by the Particle Cloud service. Woohoo, it's time for a Particle Mesh party! And the Particle Xenon is the most basic element (ha!) for...

The Electron is a small cellular IoT board made by Particle. This tiny development kit has everything you need for creating 3G cellular connected products. Includes a prepaid, no contract data plan and instant web access to your Electron with wireless programming. Kit includes: Microcontroller. Particle SIM card with service in more than 100 countries worldwide. 3...

Locate your stuff! The Asset Tracker Kit from Particle contains all of the pieces you need to build a Cellular + GPS location tracker for your most prized possessions. In addition to a GPS Shield, the Asset Tracker Kit comes with a weatherproof enclosure, so it’ll keep your electronics safe from the dust, dirt, and moisture of the great outdoors. Keep your...

Locate your stuff! The Asset Tracker Kit from Particle contains all of the pieces you need to build a Cellular + GPS location tracker for your most prized possessions. In addition to a GPS Shield, the Asset Tracker Kit comes with a weatherproof enclosure, so it’ll keep your electronics safe from the dust, dirt, and moisture of the great outdoors. Keep your...

Discontinued - you can grab Particle Boron LTE Kit - nRF52840 with LTE Cellular Modem instead! Locate your stuff! The Asset Tracker Kit from Particle contains all of the pieces you need to build a GSM + GPS location tracker for your most prized possessions. In addition to a GPS Shield, the Asset Tracker Kit comes with a weatherproof enclosure, so it’ll keep...

The ESP-WROVER-KIT from Espressif supports the most distinguishing features of the ESP32. Whether you need external SRAM for IoT applications, or an LCD+camera interface, it has you covered! The ESP-WROVER-KIT is a newly-launched development board built around ESP32. This board comes with an ESP32 module already. The version of this kit now comes with the...

The Electron is a small cellular IoT board made by Particle. This tiny development kit has everything you need for creating 3G cellular connected products. Includes a prepaid, no contract data plan and instant web access to your Electron with wireless programming. Kit includes: Microcontroller. Particle SIM card with service in more than 100 countries worldwide. 3...

The Electron is a small cellular IoT board made by Particle. This tiny development kit has everything you need for creating 2G cellular connected products. Includes a prepaid, no contract data plan and instant web access to your Electron with wireless programming. Kit includes: Microcontroller. Particle SIM card with service in more than 100 countries worldwide. 3...

This WiPy 3.0 compatible Expansion Board v3.1 brings additional functionality to your IoT project. Simply insert the WiPy 3.0 into the headers and enjoy all the extra features! This is compatible with WiPy 2.0, WiPy 3.0, LoPy, LoPy4, SiPy, FiPy and GPy! Specifications: USB and LiPo battery powered. Custom PIC USB to serial converter with automatic bootloader mode....

Arduino has discontinued this shield, please check out the Adafruit WINC1500 shield for a nearly-identical replacement with the same exact module, and the addition of a micro SD card holder and prototyping area. Arduino WiFi Shield 101 is the new IoT enabler shield based on the ATWINC1500 module, developed with ATMEL, that connects your Arduino to the internet...

The Particle Photon Kit includes a Photon with headers, a shiny white half-size solderless breadboard, a USB-micro cable, and a couple of extra surprises (two resistors, an LED, and a photocell) to help you start building your Internet of Things projects right away. Your Particle Photon comes with access to the Particle Cloud, a free cloud service. The Particle Cloud...

The Photon is a $19 tiny Wi-Fi development kit for creating connected projects and products for the Internet of Things. It's easy to use, it's powerful, and it's connected to the cloud. The tools that make up the Photon's ecosystem (and come along with the board) are designed to let you build and create whether you're an embedded engineer, web developer, Arduino...

Discontinued - you can grab this Adafruit ESP32 Feather V2 - 8MB Flash + 2 MB PSRAM - STEMMA QT instead! The Photon is a $19 tiny Wi-Fi development kit for creating connected projects and products for the Internet of Things. It's easy to use, it's powerful, and it's connected to the cloud. The tools that make up the Photon's ecosystem (and come along with the board)...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from creating or developing a WiFi Arduino shield. NO LONGER! The CC3000 hits that sweet...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from carrying any general purpose microcontroller-friendly WiFi boards. NO LONGER! The...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from creating or developing a WiFi Arduino shield. NO LONGER! The CC3000 hits that sweet...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from carrying any general purpose microcontroller-friendly WiFi boards. NO LONGER! The...