These LED strips are fun and glowy. There are 32 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 7-bit PWM precision (so 21-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 2 digital output...

You thought it couldn't get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! You wanted twice the LEDs ? We got it (well, its 1.875 times as many but that's within a margin of error). You wanted thinner strips ? Now only 12.5 mm wide, 10 mm if you remove the strip from the casing. You wanted less noticable strip color - this strip has white-colored flex PCB, which will be less visible against...

You thought it couldn't get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! You wanted twice the LEDs ? We got it (well, it's 1.875 times as many but that's within a margin of error). You wanted thinner strips ? Now only 12.5 mm wide, 10 mm if you remove the strip from the casing. You wanted less noticeable strip color - this strip has black-colored flex PCB, which will be less visible against...

You thought it couldn't get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! These NeoPixel strips have 30 digitally-addressable pixel LEDs per meter and are very affordable and are only 12.5 mm wide, 10 mm if you remove the strip from the casing. This is the strip with white flex PCB, its identical to the black 30 LED/meter except it has a different color mask on the flex strip There are some things...

Make your own little LED strip arrangement with this stick of NeoPixel LEDs. We crammed 8 of the tiny 5050 (5mm x 5mm) smart RGB LEDs onto a PCB with mounting holes and a chainable design. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Each one has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and no...

These LED strips are fun and glowy. There are 30 RGB LEDs per meter, and you can control the entire strip at once with any microcontroller and three transistors. The way they are wired, you will need a 9-12VDC power supply and then ground the R/G/B pins to turn on the three colors. Use any NPN or N-channel MOSFET (although the big powerful kind is good for a large strip) and PWM the inputs for color-mixing. For powering, a good 12V supply is...

You thought it couldn't get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! These NeoPixel strips have 30 digitally-addressable pixel LEDs per meter and are very affordable and are only 12.5 mm wide, 10 mm if you remove the strip from the casing. This is the strip with black flex PCB, its identical to the white 30 LED/meter except it has a different color mask on the flex strip There are some things...

We crammed ALL THE NEOPIXELS into this strip! An unbelievable 144 individually-controllable LED pixels on a flexible PCB. It's completely out of control and ready for you to blink. This strip has a white mask, and an extra heavy flex PCB. These LED strips are even more fun and glowy. There are 144 RGB LEDs per meter , and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set...

By popular demand, we now have a project tutorial for how to make your own programmable, ultra-blinky LED belt. Perfect for parties, raves, parades, weddings, funerals, and bar mitzvahs. Wear it with pride, wear it with blinky! Follow our soldering tutorial to build your own heirloom LED belt, and hand it down to your grandkids. We designed this project to demonstrate how to use the digital LED strip, how to use our Atmega32u4 breakout...

These LED strips are fun and glowy. There are 60 RGB LEDs per meter - twice as many as our other strip, and you can control the entire strip at once with any microcontroller and three transistors. The way they are wired, you will need a 9-12VDC power supply and then ground the R/G/B pins to turn on the three colors. Use any NPN or N-channel MOSFET (although the big powerful kind is good for a large strip) and PWM the inputs for color-mixing. We...

We crammed ALL THE NEOPIXELS into this strip! An unbelievable 144 individually-controllable LED pixels on a flexible PCB. It's completely out of control and ready for you to blink. This strip has a black mask, and an extra heavy flex PCB. These LED strips are even more fun and glowy. There are 144 RGB LEDs per meter , and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set...

These LED strips are fun and glowy. There are 60 warm white LEDs per meter, and you can control the entire strip at once with any microcontroller and a power transistor. The way they are wired, you will need a 9-12VDC power supply and connect directly. If you want to dim the strip, use any NPN or N-channel MOSFET (although the big powerful kind is good for a large strip) and PWM the input. We splurged and got the weatherproof kind with white...

These LED strips are ultra bright, fun and glowy. There are 60 cool white LEDs per meter, and you can control the entire strip at once with any microcontroller and a power transistor. The way they are wired, you will need a 9-12VDC power supply and connect directly. If you want to dim the strip, use any NPN or N-channel MOSFET (although the big powerful kind is good for a large strip) and PWM the input. We splurged and got the weatherproof kind...

BlinkyTape is a very special LED strip, taking the smarts of NeoPixels and combining it with an Arduino-compatible for an all-in-one ready to go design. You don’t have to source your own microcontroller, power supply or connectors. Simply plug in a standard USB battery pack or wall charger, and you’re good to blink. BlinkyTape has 60 independently controllable full-color RGB LEDs, all wrapped up in a weather-resistant silicone case. All this...

This touch controller set is a quick and easy way to control a bunch of our 12V analog RGB LED strip. The box part contains power driver circuitry and an RF receiver. The handheld remote contains a capacitive touch interface and an RF transmitter. By wiring the analog strip to the box you can easily adjust the color from across the room. Since it is RF you don't need line-of-sight like you would with an IR Remote. The box has a few 'programs'...

These ingenious little clips make it easier than ever to use our analog LED strips - no need to solder! The clips snap onto the ends of the LED strip and hold securely. They're not waterproof but you could cover them in heat-shrink to make them weatherproof. You get one piece of three different types: One is a short "joiner" - it can join two strips together. The second type is a long "joiner" - it can join two strips together 6" apart. The...

This touch controller set is a quick and easy way to control a bunch of our 12V analog RGB LED strip. The box part contains power driver circuitry and a capacitive touch interface. By wiring the analog strip to the box you can easily adjust the color with the touch wheel-- perfect for mounting on the wall. The box has a few 'programs' built in, such as rainbow fading and a really obnoxious colorful blinking effect. However, you'll probably end...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...

For those that want to cut, customize, and cap our awesome Digital Addressable RGB LED strips we now have a pack of the little rubber caps. These fit perfectly over the strips, use silicone glue to secure and waterproof them. Comes in a pack of 4 pieces

These nylon clips will let you attach our flexible NeoPixel strips to a wall, moulding, or project. Just side the rubber tubing thru so that the clips are in between two LEDs. Comes in a pack of 5, you also get 10 screws as shown. Silicone Clips and Screws for NeoPixel LED Strips - set of 5 (3:00)

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...