Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero W Basic Pack is the barest of essentials that you'll need to get going with your WiFi-enabled Pi Zero W and make it a complete meal. This pack includes: ...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal.  The Pi Zero W Starter Pack is everything you need to get going with your WiFi-enabled Pi Zero W and make it a complete meal. Note: Due to popular demand, there might be some...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero W Budget Pack is almost everything you need to get going with your WiFi-enabled Pi Zero W and make it a complete meal. Note: Due to popular demand, there might be...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal.  The Pi Zero Stereo W Bonnet Pack  sets you up with the WiFi-enabled Pi Zero W, and our I2S 3W Stereo Speaker Bonnet. This bonnet uses digital sound standard...

If you didn't think that the Raspberry Pi Zero could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero W offers all the benefits of the Pi Zero v1.3, but with one big difference – built-in WiFi! More specifically, this giant upgrade is the addition of a BCM43143 WiFi chip BUILT-IN to your Raspberry Pi Zero – just like the Pi 3! No more pesky WiFi adapters - this Pi is...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero Budget Pack is almost everything you need to get going with your Pi Zero and make it a complete meal. Check out our writeup on the Pi Zero over at the Adafruit Learning...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal.  The Pi Zero Starter Pack is everything you need to get going with your Pi Zero and make it a complete meal. Check out our writeup on the Pi Zero over at the Adafruit Learning System...

Now that we're carrying the Pi Zero,   PaintYourDragon is back with another gorgeous laser-cut masterpiece. This time he's taken a pass at a Pi Protector for Raspberry Pi Zero, not quite a full case, it will keep your Pi Zero safe and svelte. Keep your Raspberry Pi® Zero computer tidy and safe in this lovely clear acrylic enclosure. We designed this  simple protector to be beautiful, easy to assemble and perfect for...

If we could eat headers, we'd have them for breakfast, lunch, and dinner.  But we can't :( So we're making the best of it and selling them! This 2x20-pin strip male header is a great way to add pins to 2x20 0.1" holes in a PCB.  They're also perfect companion piece to our 2x20-pin right-angle female header.

If we could eat headers we'd have them for breakfast, lunch, and dinner.  But we can't :( So we're making the best of it and selling them! This 2x20-pin strip, right-angle female header is a perfect companion piece to our 2x20-pin Dual Male Header.  It's a great way to add right-angle capability to a 2x20 pin circuit board either by attaching the right-angle male headers to the board and having a right-angle female...

What an adorable little pug! Sorry - plug! What an adorable mini HDMI to HDMI plug.  We find this plug adapter really helpful.  It's a great way to convert any mini HDMI plug to a normal HDMI plug and...that's about it! Now you can use any of your classic HDMI cables. Simple.  Useful.  Adorable. Note:  This product may come in black or white.  They are functionally the same.  We cannot control...

This cable looks like a USB micro cable but it isn't! Instead of a USB A Plug, it has a USB A Socket on the end. This cable is designed for use with OTG (On the Go) host devices (like the Arduino Due or many tablets) so you can connect a mouse, keyboard, or any other USB device. You'll still need to have drivers on the device, this cable is just a cable and contains no microcontroller or electronics inside. Approximately 6" long...

This super slim, super tiny, and super cute Micro-B to USB on-the-go adapter is so slim, tiny, and cute that we'd pinch its cheeks if it was big enough to have cheeks.  At just ~15.5mm long, ~11.3mm wide, and ~2mm, this really is the tiniest little adapter we've probably ever seen. But don't let the size fool you - this is a perfect and easy way to turn a device or cable with a USB-A to a USB-micro, great for use with OTG...

Crafted out of four transparent acrylic pieces the  Pibow Zero Case for Raspberry Pi Zero protects your Pi while showing it off to the world! Each layer is laser-cut from colorful, lightweight, and high-quality cast acrylic. All of the primary ports and GPIO pins are accessible (it encloses the micro-SD slot). No tools are necessary for assembly or disassembly and the case comes in at a conveniently lightweight 34g....

Having a discrete, slick, and tidy power supply is always tricky when taking a project on the go...but get ready to roam the earth worry free with the tiny little Pimoroni LiPo Shim ! It aims to give you the most compact power supply possible for all versions of Raspberry Pi. You can either solder the 0.8mm thick PCB directly to the bottom of your GPIO header for a permanent solution or solder on the provided 2x6 0.1" female...

If you have a computer or tablet or device with Mini HDMI output but you want to connect it to a projector, monitor or display with VGA input, you have come to the right place! This nifty adapter cable has a Mini HDMI plug connector at one end and at the other end a DB-15 VGA connector (it has hex nuts that you can remove if you are trying to mate it with a cable that also has hex nuts). There's also an audio jack on the side, this provides...

This is a 16GB microSDHC card that comes with a SD adapter and is pre-programmed to contain Raspbian Stretch Lite - released in November of 2018.   Note: this is not compatible with Raspberry Pi 4 Model B.  You'll want the 16GB Card with NOOBS 3.1! Raspbian is a free operating system based on Debian optimized for the Raspberry Pi hardware. An operating system is the set of basic programs and utilities that make your Raspberry...

Ideal for monitoring conditions in your house, garage, and more, the Pimoroni  Enviro pHAT packs 4 different sensors, letting you measure temperature, pressure, light level, color, 3-axis motion, compass heading, and analog inputs. That's up to 10 different variables! Snap it   on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a comprehensive environment-sensing pHAT powered directly from the Pi....

The Explorer pHAT is the perfect prototyping side-kick for your Raspberry Pi. Based on Pimoroni's popular Explorer Hat Pro, this is a smaller cheaper version designed to fit perfectly on a Raspberry Pi Zero! A heap of useful input and output options have been added that will take your projects to the next level. Great for driving motors, using analog sensors, and interfacing with 5V sensors & systems Though...

The OLED Bonnet Pack for Raspberry Pi Zero  sets you up with the Pi Zero W, and our popular 128x64 OLED Bonnet. It's the big sister to our mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger screen. With the OLED display in the center, we had some space on either side so we added a 5-way joystick and two pushbuttons. The OLED Bonnet is great for when you want to have a control interface for...

Wrap your new little Raspberry Pi Zero in protective and elegant wooden plates with the Zebra Zero ! A simple and versatile installation makes this case one of our favorites. The clever C4 nuts used to hold the case together can accept a screw from either end so if you want to install a PiHAT it can be secured to the nuts on the other side! A straight or right-angle GPIO header can be soldered in from either side of the board too. We also...

Snap the Pimoroni Unicorn pHAT  on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a fun 4x8 RGB LED matrix powered directly from the Pi. The Unicorn pHAT provides a wash of controllable color that is ideal for mood-lighting, 4x8 pixel art, persistence of vision effects, status indications, or just blasting color into your surroundings. 32 fully controllable RGB LEDs (SK6218 - 3.5mm x...

One can never have enough socks, or USB ports. Add some more USB and Ethernet capability to your Raspberry Pi Zero or, really, any kind of tablet or computer with an OTG connector with this USB 2.0 and Ethernet Hub ! This handy combo-hub has 3 USB 2.0 ports, and a AX88772A Ethernet transceiver. This chipset is really common and can be used by any Linux, Mac or Windows computer. It's particularly handy for the Raspberry Pi...

If music be the food of love, play on. But make sure you use this super little pHAT DAC to get the best out of your Raspberry Pi audio! The pHAT DAC provides a super affordable high-quality DAC for the Raspberry Pi. Pumping out 24-bits at 192KHz of audio goodness from the Raspberry Pi's I2S interface on the 2x20 pin GPIO header. Since it's digital audio, it sounds really good, much better than the onboard analog audio. The 3.5mm...

This camera cable is specifically designed to work with the Raspberry Pi Zero - Version 1.3! Just plug it into your Pi Zero's camera port and then the other end into one of the official Pi Cameras for photo & video joy. The Raspberry Pi Zero is NOT included in this product! If you're looking to buy a Raspberry Pi Zero, check out our selection of packs here!  

At first glance, the Pi Zero isn't much.  It just looks like a slimmed down version of the Raspberry Pi we know and love.  But when we started to think of the possibilities - and what a well-chosen set of accessories could add - we realized the appeal.  And then we saw the price...could it be true? Yes! This is the slimmest, most pared down Raspberry Pi to date.  It's kind of like the little cousin to the Pi 2 -...

The Joy Bonnet Pack for Raspberry Pi Zero W sets you up with the Pi Zero W, and our Joy Bonnet  -  our most fun Bonnet ever! This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you install our script onto your Pi, the controls will act like a keyboard, for easy use with any emulator or media player. Note: Due to popular demand, there might be some delay in...

Design your own Bonnet or pHAT, attach custom circuitry and otherwise dress your Pi Zero with this jaunty prototyping Bonnet kit! To add to the Adafruit Bonnet party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with...

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero mini computer. ePaper / eInk is a display technology that mimics the appearance of ink on normal paper. Unlike conventional displays, ePaper reflects light – just like ordinary paper – and is capable of holding text and images indefinitely, even without electricity. Because of this,...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers  from Pimoroni might be just what you need. They come in both male and female, and use crafty little retaining nubbins to grip tightly into the holes on the PCB. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to...

This is a basic, classic Pi Zero enclosure with a black base and a clear top. The case is as minimal as it gets, coming in just two pieces of polycarbonate that snap snugly together. This case will keep your Pi Zero safe and secure while also looking super sleek. You can use all of the connectors on the edges of the Pi: mini HDMI, microSD slot, microUSB power, and microUSB port. There's also a cut out to allow a 2x20-pin header to...

The  Snake Eyes Bonnet  is a  Raspberry Pi accessory  for driving  two 128x128 pixel OLED  or  TFT LCD  displays, and also provides four  analog inputs  for sensors. It's perfect for making cosplay masks, props, spooky sculptures for halloween, animatronics, robots...anything where you want to add a pair of animated eyes! This product is just the Pi Bonnet itself, and some headers so you can...

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero with the  Zero4U ! This is a 4-port USB hub for Raspberry Pi Zero, and it can be mounted back-to-back onto a Pi Zero. The 4 pogo pins on the back will connect the PP1, PP6, PP22 and PP23 testing pads on your Raspberry Pi Zero – no soldering required! This item can only work with the Zero W if a ferrite ring is...

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Pimoroni's Automation pHAT  – the little sibling of the Automation HAT – is the most compact way to take control of and monitor your world! Pimoroni has pulled together a great set of features into this home monitoring and automation controller. With a relay, analog channels, powered...

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little pHAT. It's the neatest way to add audio to your Pi project, and its beautiful artwork evokes an 80s boombox! Pimoroni isn't claiming audiophile sound quality, but it's perfect for fun little projects where you want to add sound output – speech, notification sounds, or light...

Playing retro games is easy on a Raspberry Pi - and that pocket-sized computer is pretty good at it too! All you need is a little help to connect buttons and a joystick up and you can custom design your own arcade console, desktop or stand-up machine, even just a simple controller box. It makes for a fun weekend project that will last all year. This Adafruit Arcade Bonnet is designed to make small emulator projects a little easier to build....

Still searching for the Pi Zero enclosure that works for you? Try out this fully injection molded Raspberry Pi Zero case from ModMyPi! Designed to optimise protection whilst maintaining device useability, this Pi Zero case consists of a 3-part clip together construction with microSD card cover and embossed Raspberry Pi Foundation logo, which acts as a ventilation point for heat extraction. Each case features a top and bottom GPIO...

Hey Mr. DJ! Turn up that Raspberry Pi mix to the  max  with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi . (It's not big enough to be an official HAT, so we called it a bonnet, you see?) It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi computers with a 2x20 connector - A+, B+, Zero, Pi 2, Pi 3, etc. We've tested it out with Raspbian (the official operating system) and...

If you didn't think that the Raspberry Pi Zero W could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero WH  offers all the benefits of the Pi Zero W, but with one big difference – a pre-soldered GPIO header! This upgrade is the addition of a BCM43143 WiFi chip BUILT-IN to your Raspberry Pi Zero – just like the Pi 3! No more pesky WiFi adapters - this Pi is WiFi...

This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in another USB device. For example, a Pi Zero or Pi Zero W has a OTG port, as does the Arduino Zero, and anything with an ATSAMD21 that is in USB host mode. Also great for when you want to attach to a tablet or phone with an OTG...

Here's a snazzy accessory for your Raspberry Pi Zero or Zero W, a color-coded 2x20 header! This Color Coded Header  takes the mystery out of your Raspberry Pi's 2x20 pinout. No longer will you stare in confusion at all 40 pins, trying to count out which one you want to plug your wires into. Peep this handy color coding: Red = 5VYellow = 3VBlack = GNDBlue = Do Not ConnectGreen = GPIO Connecing to your Pi Zero requires a bit...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers  from Pimoroni might be just what you need.  Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero, Bonnet, HAT or pHAT. Make sure to carefully read Pimoroni's guide for fitting hammer headers. The...

A long time ago we made a Pi into a WiFi gateway that also blocked ads but the Pi Hole project does a  way  better job! This kit will make your Pi Zero W act as a DNS ( Domain Name Server ) The kind of device that tells you that  adafruit.com  is known as IP address 104.20.38.240. Except, when Pi Hole DNS is installed, it will do a special trick, when it is asked for the IP address of ads.adserver.com (for example) it will...

If you'd like a compact display, with buttons and a joystick - we've got what you're looking for. The Adafruit 128x64 OLED Bonnet for Raspberry Pi is the big sister to our mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger screen besides. With the OLED display in the center, we had some space on either side so we added a 5-way joystick and two pushbuttons. Great for when you want to have a...

Google AIY Projects brings do-it-yourself artificial intelligence to your maker projects. The  Google AIY Vision Kit  lets you build an image recognition device that can see and identify objects, powered by TensorFlow’s machine learning models. The kit includes all of the components needed to assemble the basic kit that works with the Google Assistant SDK as well as on-device image & vision recognition with TensorFlow using...

Add some easy-listenin' tunes to your Raspberry Pi using this basic audio bonnet. It'll give you stereo line out from a digital I2S converter for a good price, and sounds nice to boot! This bonnet features the UDA1334A I2S Stereo DAC, a perfect match for any I2S-output audio interface. It's affordable but sounds great - music to our ears. It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi...

We've got to hand it to the Pi Foundation - adding a camera port and  built-in WiFi to the already awesome Pi Zero was a brilliant move. Now you can add one of the awesome Raspberry Pi cameras to your Pi Zero W to make a super low-cost, functional camera. This version includes the 8 MegaPixel Pi Camera.  If you're looking for the pack with the NoIR Megapixel camera, click here! Note: Due to popular demand, there might be...

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. We basically took our super-popular DC+Stepper Motor HAT and squeezed it down and made it fully assembled - plug and play ready to go, no soldering required! Raspberry Pi and motors are not included. Works with any and all...

Zero Stem?  More like, full stream ahead! This is a neat little PCB shim that transforms your Raspberry Pi Zero into a USB dongle! Super handy when you want to share your computer's Internet connection without messing with extraneous adapters, cables, what have you. Works great with our USB Gadget for Raspberry Pi Zero guide. Once soldered on, the Stem lets you plug into USB to get power and data over a computer USB port. Use it on the...

The first 'official' Pi Zero case from the Raspberry Pi Foundation is here in Raspberry Pi's sleek pink and white! While we've had our own classic Pi Zero case for a little while now, the Pi Foundation celebrates the release of the Pi Zero W with this impressive, well-designed effort that is definitely what we've come to expect from the folks who made the Raspberry Pi. The case comes in four parts – a pink...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers  from Pimoroni might be just what you need.  Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero or pHAT/bonnet/HAT. Make sure to carefully read Pimoroni's guide for fitting hammer headers. These...

Add a tiny yet convenient power switch to your Pi with Pimoroni's On-Off SHIM ! Pimoroni's SHIMs (Shove Hardware in the Middle) are a new range of boards designed to be small, affordable, and handy. They're just 0.8mm thick (the bare board, not including mounted components) and designed to be soldered straight onto the GPIO pins of your Pi, if you wish, so that you can use them with HATs and pHATs on top. Usage Just plug your...

We've got to hand it to the Pi Foundation - adding a camera port and  built-in WiFi to the already awesome Pi Zero was a brilliant move. Now you can add one of the awesome Raspberry Pi cameras to your Pi Zero W to make a super low-cost, functional camera. This version includes the 8 MegaPixel Pi NoIR Camera.  If you're looking for the pack with a normal 8 Megapixel camera, click here! Note: Due to popular demand, there...

Pocket-sized fun is the name of this game, with the Joy Bonnet  – our most fun Bonnet ever (no we didn't even think that was possible, either!). This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you install our script onto your Pi, the controls will act like a keyboard, for easy use with any emulator or media player. Personally, we found this Bonnet...

Crafted out of four transparent acrylic pieces, the  Pibow Zero W Case for Raspberry Pi Zero W protects your Pi while showing it off to the world! Each layer is laser-cut from colorful, lightweight, and high-quality cast acrylic. All of the primary ports and GPIO pins are accessible (it encloses the micro-SD slot). The case is lightweight and ideal for mounting to any surface. No tools are required for assembly or...

Pimoroni's Button SHIM gives you five handy, physical buttons and an RGB status LED, and it's HAT and pHAT-compatible! Pimoroni's SHIM-format boards are designed to slip neatly onto your Pi's GPIO pins and still allow you to use HATs and pHATs at the same time. Or solder the included female header onto Button SHIM and use it as a standalone board. The buttons and status LED stick out from the top edge of your...

We've got to hand it to the Pi Foundation - adding a camera port to the already awesome Pi Zero was a brilliant move.  Now you can add one of the awesome Raspberry Pi cameras to your zero to make a super low-cost, functional camera. This pack provides everything to get your Raspberry Pi Zero camera up and running.  We've included a: Raspberry Pi Zero V1.3 Warning! This does  NOT  include the new Pi Zero W. ...

The Joy Bonnet Pack for Raspberry Pi Zero WH  sets you up with the fully assembled Pi Zero WH, and our Joy Bonnet  -  our most fun Bonnet ever! This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you install our script onto your Pi, the controls will act like a keyboard, for easy use with any emulator or media player. This pack is plug-and-play, no...

We've got to hand it to the Pi Foundation - adding a camera port to the already awesome Pi Zero was a brilliant move.  Now you can add one of the awesome Raspberry Pi cameras to your zero to make a super low-cost, functional camera. This pack includes the 8 MegaPixel Pi Camera.   If you're looking for the pack with the NoIR Megapixel camera, click here! This pack provides everything to get your Raspberry Pi Zero camera up and...

The Pimoroni Touch pHAT has six capacitive touch buttons, each with a bright white LED, so you can add a touch interface to your Raspberry Pi. While it is shaped and sized to match a Pi Zero, it works great with any Pi with 2x20 connector. You can even use a dry erase pen to write on the pads to label their function. The pHAT features a CAP1166 capacitive touch and LED driver chip that is read over I2C. Each pad has a matching LED that can be...

What if Scroll pHAT had twice times as many pixels and individual pixel brightness control? Scroll pHAT HD , that's what!! Scroll pHAT HD packs 17x7 bright white pixels (119 total) onto a single pHAT, and gives you full PWM brightness control over each pixel. Create beautiful animations and even anti-aliased text by taking advantage of the per-pixel brightness. Use Scroll pHAT HD as a scrolling message display for your tweets, the weather or...

You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet .  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors  What is particularly nice about this Wing is...

Add mega-storage in a jiffy using this 8 GB micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters! Preformatted to FAT so it works out of the box with our projects. Tested and works great with our Wave shield, Data logger shield and GPS shield, and micro-SD adapter as well as any other device in the Adafruit shop that uses (micro)-SD cards! Also perfect for use with Raspberry Pi computers, just burn the...

Wrap your new little Raspberry Pi Zero in protective and elegant wooden plates with the Zebra Zero Plus ! The Zebra Zero Plus includes a breadboard for prototyping making this a nice and full-on prototyping platform for you and your Pi Zero. There's also a GPIO pin header reference chart etched on the back for reference. As is the case with all of our favorite enclosures, all of the pins on the Pi are easily accessible from the top! We also...

Let your Pi talk back with this slick little 11x5 LED matrix Scroll pHAT ! The Scroll pHAT provides a matrix of 55 white LED pixels that is ideal for writing messages, showing graphs, and drawing pictures. Use it to output your IP address, show CPU usage, or just play very-low-rez pong! Though designed to match the format of the Raspberry Pi Zero it is compatible with all 40-pin GPIO Raspberry Pi variants (2/B+/A+). Features: 55 white...

Looking for an unashamedly old school LED matrix display board? Lookie here! The Pimoroni Micro Dot pHAT is made up of six red LED matrices, each 5x7 pixels (for an effective display area of 30x7) plus a decimal point, using the beautiful little Lite-On LTP-305 matrices. Perfect for building a retro scrolling message display, a tiny 30-band spectrum analyzer, or a retro clock. Far out! As with the other pHATs, it works with all of the...

So you've got your Pi 3 with its built-in wireless LAN and Bluetooth, but what about your Pi Zero? Say hello to the IoT pHAT from Red Bear! This Zero-size board provides WiFi (802.11bgn / 2.4GHz) and Bluetooth (v4.1 / BTLE) connectivity direct from the GPIO header. You don’t need to use a dongle plugged into the Pi Zero’s solitary data micro-USB port via a USB OTG adapter. Just snap it   on top of a Raspberry Pi...

PiJack  is a HAT (yes, a proper HAT, not a pHAT!) add-on board for the Raspberry Pi Zero mini computer that makes connecting your Pi Zero to the Internet via Ethernet super simple. If you're fed up with flaky WiFi and want your Pi Zero to be online all the time, then this HAT is for you! PiJack is a neat little board with an Ethernet controller and standard RJ45 connector so you can hook your Pi up to your home or office...

So you've got your Pi 3 with its built-in wireless LAN and Bluetooth, but what about your Pi Zero? Say hello to the IoT pHAT from Red Bear! This Zero-size board provides WiFi (802.11bgn / 2.4GHz) and Bluetooth (v4.1 / BTLE) connectivity direct from the GPIO header. You don’t need to use a dongle plugged into the Pi Zero’s solitary data micro-USB port via a USB OTG adapter. Just snap it   on top of a Raspberry Pi...

Our pirate friends at Pimoroni have taken the I2S mono DAC and amplifier that they used on Speaker pHAT and Picade HAT and added a second one for stereo goodness. pHAT BEAT gives you high-quality, digital, amplified, stereo audio and 16 beautiful little RGB LEDs, in two rows of 8, that are ideal as a VU meter, and 6 buttons to control your audio. There's a nifty little DIP switch on the bottom of the...

AHOY , wanna spell out some LOVE with this COOL Raspberry Pi FOUR letter PHAT ? Pimoroni's Four Letter pHAT has four 14-segment displays that you can use to display text, numbers, and a host of other characters. The LEDs are a beautiful retro green, just like your old digital alarm clock. They're driven by the HT16K33 chip over I2C, which does all the multiplexing for you. While it is shaped and sized to match a Pi Zero, it works great...