Components & Parts / Sockets/Connectors / Other

What do you do when you want to tinker with GPU hardware, but you don't have a display on hand? This HDMI Dummy Plug is a small device that acts as a display emulator. Once it's plugged into the video output socket on your device or computer, the plug punks the operating system into detecting a connected display, and voilà! Now you have unimpeded access to...

This socket is good for any SOIC/SOP Wide-body 8 pin chip in a 200mil wide body. Simply flip open the latch, insert the chip, and flip down the latch to secure it in place. The chip is held securely against gold 'fingers' (no, stop, Mr. Bond! It's not that Goldfinger!) in the socket. The bottom footprint matches the same SOIC footprint so you can solder this onto an...

This socket is good for any SOIC/SOP Wide-body 16 pin chip in a 300mil wide body. Simply flip open the latch, insert the chip, and flip down the latch to secure it in place. The chip is held securely against gold 'fingers' (no, stop, Mr. Bond! It's not that Goldfinger!) in the socket. The bottom footprint matches the same SOIC footprint so you can solder this onto an...

"Is it not a strange fate that we should suffer so much fear and doubt for so small a thing? So small a thing!!" – Boromir, The Lord of the Rings That Raspberry Pi camera or display (CSI/DSI) connectors can sometimes get damaged, and it would be a shame to have to toss the whole thing! Maybe you got a little over-enthusiastic and She-Hulk'd out on the connector...

We designed this little breakout board after seeing some cool demos for the Raspberry Pi Pico driving an HDMI display. By using some fun 'abuse' of overclocking and the RP2040's PIO system a low-cost microcontroller can have great looking video output. Great for making demos, or just noodling around with digital video generation. This breakout board has no active...

These Banana Plugs not only look great, they're also solder-free and stackable! Banana plugs are often used on test equipment, tools, synthesizers and other electronic patch panels. Each connector is designed with bowed strips to provide secure and uniform contact between the plug and jack. Even after multiple insertions, the non-collapsing design stays true to form....

You may have noticed that our RP2350 Feather has an FPC output connector on the end for accessing the HSTX (High Speed Transmission) peripheral. This new capability, not available on the RP2040, is specifically designed to allow the RP2350 chip drive DVI displays really easily! Historically you could use DVI on the RP2040 by mashing together some overclocking and a...

Totaling 150 connectors and matching plastic sheaths, this Spade Quick Connector Kit is a must-have for your workstation. You'll have enough connectors to fuel your maker tendencies for days on end! Perfect for making wire harnesses to micro switches, arcade buttons and toggle switches. These connectors are really common in electronics, we use with our arcade button...

If you want the look and feel of aeronautical style quick-release connectors, this FGG.0B 4-pin Socket is an elegant and inexpensive alternative to official LEMO-C connectors. Sure, they're not mil-spec but they do work and look great for DIY projects, keyboard builds, robotics, wearables, and more. The connector snaps together smoothly and can disconnect only when...

If you want the look and feel of aeronautical style quick-release connectors, this FGG.0B 4-pin Plug is an elegant and inexpensive alternative to official LEMO-C connectors. Sure, they're not mil-spec but they do work and look great for DIY projects, keyboard builds, robotics, wearables, and more. The connector snaps together smoothly and can disconnect only when the...

This accessory for the Bus Pirate 5 makes it trivial to program bare flash memory chips without clips or soldering. SOP8 150mil and 208mil are the most common and inexpensive flash packages at the moment. After looking at a number of sockets, the folks behind the Bus Pirate 5 decided these bad boys, favorites of the mobile phone repair market, were the way to go....

If you have any LEGO Mindstorm or EV3 sensors/motors/controllers you probably noticed the phone-cable-like connectors that are used to go from accessories to controller boards. However, you can't use every-day phone jacks or cables because the little plastic clip is on the sidenot the center. No need to give up your dreams of interfacing with NXT parts, though! These...

Swapping around your SIM card into different devices? This trio of SIM adapters helps so that you can use one SIM card for various size-needs. Two adapters fit Nano-SIMs (~12mm x ~9mm x ~0.7mm) and one fits Micro-SIMs (~15mm x ~12mm x ~0.8mm). In our two examples we broke down our GSM 2G SIM Card from Ting & Adafruit to it's smallest Nano self. Once in the...

If you want to do more with the BBC micro:bit, getting those pins from the card-edge connector is going to be your first hurdle. Unlike many dev-boards, the micro:bit isn't breadboard-friendly. That makes the 'bit durable and easy to manufacture but means you need a special connector. This surface-mount edge connector is very slim and fully SMT, so it's a breeze to...

If you want the look and feel of aeronautical style quick-release connectors, this FGG.0B 5-pin Plug is an elegant and inexpensive alternative to official LEMO-C connectors. Sure, they're not mil-spec but they do work and look great for DIY projects, keyboard builds, robotics, wearables, and more. The connector snaps together smoothly and can disconnect only when the...

We're big fans of the Intel® Edison Compute Module but the connector's not generic like everyday header, and can be a bit difficult to find. No longer! This 70-pin receptacle header for the Intel Edison connects to the Edison Compute Module and allows breakout boards to be added more easily. If you're in the Edison block business, this is for you It's a tiny...

Add SIM-card capabilities to your next project with this SIM Card Holder. It works great with any Mini-SIM (25mm x 15mm x ~0.8mm) including our GSM 2G SIM Card from Ting & Adafruit. It's not too bad to solder, the pads are pretty large, even though its surface mount. Each order comes with one holder, no SIM card included. To use in your Eagle CAD project, check...

If you want the look and feel of aeronautical style quick-release connectors, this YC-8 5-pin Connector Matching Pair is an elegant and inexpensive alternative. Sure, they're not mil-spec but they do work and look great for DIY projects, keyboard builds, robotics, wearables and more. The connector snaps together smoothly, and can disconnect only when the sleeve is...

If you want the look and feel of aeronautical style quick-release connectors, this YC-8 4-pin Connector Matching Pair is an elegant and inexpensive alternative. Sure, they're not mil-spec but they do work and look great for DIY projects, keyboard builds, robotics, wearables and more. The connector snaps together smoothly, and can disconnect only when the sleeve is...

Discontinued - you can grab this Kitronik Inventor's Kit for the BBC micro:bit - micro:bit Not Included instead! The Kitronik Breadboard Breakout for the BBC micro:bit lets you plug a BBC microbit into a standard 2.54mm pitch breadboard. Two 11-pin headers are used to make connections into the breadboard. Works with micro:bit v1, v2, CLUE, HiFive Inventor and other...