Tools / Test Equipment / Fixtures and Probes

The Pogo Pin Probe Clip with 6 pins in a 2.54 / 0.1" pitch spacing is a great way to test and connect with pin-point accuracy without soldering! It's sort of like an alligator clip with an array of built-in springy pogo pins - so you can connect to a PCB with classic 0.1" spaced pad holes, without soldering or a special adapter cable. The clip is constructed from PCB...

Doesn't this fixture clamp look like a character in a Pixar movie? If you just drew two little eyes on it then you could just imagine it hopping around on nifty, adorable little adventures that are heartwarming and...sorry, we got carried away. This fixture clamp is a great way to hold a printed circuit board in place while you're testing or programming. It comes...

*Ka-thunk* Pin down that PCB with our Toggle Clamp, a sturdy and reliable way to quickly press and release with precision! A pogo-pin bed is a great way to connect and test boards without any soldering, but you have to somehow get that PCB aligned right and evenly pressed down on each pogo. After much experimenting, we settled on this toggle clamp and we use it all...

Kelvin clips are used whenever you need to get a measurement right at the contact points of a circuit or component. Even though these are grippy clips, each side of the clip is electrically insulated. So you can use it to grab onto a part (as seen above) and perform measurements. These can also be used in circuit if needed. The clip is bare and comes with two jaw...

*Ka-thunk* Pin down that PCB with our Toggle Clamp, a sturdy and reliable way to quickly press and release with precision! A pogo-pin bed is a great way to connect and test boards without any soldering, but you have to somehow get that PCB aligned right and evenly pressed down on each pogo. After much experimenting, we settled on this toggle clamp and we use it all...

Totaling 420 pieces, this White Nylon M2.5 Screw Set is a must-have smörgåsbord for your workstation. You'll have more than enough screws, nuts, and hex standoffs to construct your maker projects for days on end! M2.5 screws fit nearly all of the Adafruit breakout/development board mounting holes (2.5mm or 0.1" drill holes). These screws work handsomely...

Testing and debugging is a challenging step in board manufacturing. It can be super tricky on a fully populated PCB. So how can you test connections when you have an assortment of components blocking your probe? These Basic Micro SMT Test Hooks have solderable tabs on one end so you can attach a wire, and on the business end, a spring-actuated double-hook.They easily...

*Ka-thunk* Pin down that little PCB with our Toggle Clamp, a sturdy and reliable way to quickly press and release with precision! A pogo-pin bed is a great way to connect and test boards without any soldering, but you have to somehow get that PCB aligned right and evenly pressed down on each pogo. After much experimenting, we settled on this toggle clamp and we use...

Totaling 420 pieces, this M3 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end! M3 size screws fit a number of Adafruit breakout/dev board standoffs. Since they are nylon you can file them down easily, and they don't conduct electricity or interfere with...

The Pogo Pin Probe Clip is a great way to test and connect with pin-point accuracy without soldering! It's sort of like an alligator clip with a built-in springy pogo pin - so you can connect to any PCB pad for 'scoping, analyzing, or multimetering. The clip is strong enough to grip onto a PCB but has a soft grip so it won't mar or damage circuits. The 'tongue' is a...

The Pogo Pin Probe Clip with 2x5 0.05" pitch SWD spacing is a great way to test and connect with pin-point accuracy without soldering! It's sort of like an alligator clip with an array of built-in springy pogo pins - so you can connect to a PCB with classic 'SWD' pad holes, without soldering or a special adapter cable. The clip is constructed from PCB sections, with...

Testing is an important step in board manufacturing. And it can be super tricky on a fully populated PCB. So how can you test connections when you have an assortment of components blocking your probe? These "mini loop type" Small PCB Test Points easily snap in to your project, and they're ideal for ultra-low profile surface-mount testing! They will attach to J hooks,...

Testing is an important step in board manufacturing. And it can be super tricky on a fully populated PCB. So how can you test connections when you have an assortment of components blocking your probe? These "mini loop type" Small PCB Test Points easily snap in to your project, and they're ideal for ultra-low profile surface-mount testing! They will attach to J hooks,...

This luxurious accessory will make your Bus Pirate 5 a joy to use. This keyed and locking probe cable made of premium soft and flexible silicone-coated wire connects to the Bus Pirate 10-pin main header. The ends are 2.54mm Dupont connectors that fit many different types of probe hooks, as well as custom-milled breadboard adapter pins. Silicone covered wires means it...

Totaling 380 pieces, this M2.5 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end! M2.5 size screws fit almost all of the Adafruit breakout/dev board mounting holes (2.5mm or 0.1" drill holes). Works great with many Feathers, Adafruit breakout boards, Pi HATs and plates, and...

This cable will make it super easy to use our plug-and-play STEMMA QT boards and controllers with chips, breakouts, and other devices that are I2C compatible but don't come with a STEMMA QT socket already on 'em. On one end you get a Qwiic / STEMMA QT connector (technically known as a JST SH 4-pin plug) into 4 individual wires with 'micro hook' ends. The hooks are...

When alligator clips and even scope probes are too large, IC hooks come to the rescue! These fine clips are very nice, and come in a set of 9 colors (black, brown, red, orange, yellow, green, blue, violet, gray). They provide a nice strong grip on SOICs, TQFPs, anything with 0.6mm pin pitch or larger. The hook is made of strong gold-plated 'piano wire', and there are...

The Computer Repair Screw and Standoff Kit contains all those bits and pieces that get lost whenever installing stuff into your computer or electronics devices: the screws, standoffs, washers and more that are used for the chassis, fan, motherboard and component extras. They may also be used by other electronic devices around your home. Particularly useful if you are...

Testing is an important step in board manufacturing. And it can be super tricky on a fully populated PCB. So how can you test connections when you have an assortment of components blocking your probe? These "mini loop type" Small PCB Test Points easily snap in to your project, and they're ideal for ultra-low profile surface-mount testing! They will attach to J hooks,...