LCDs & Displays

Looking for the best LCDs & displays for your projects? Need a screen for your next Arduino project? Or, how about an Adafruit Qualia Retina Display? Check out Adafruit's LCDs & Displays section for LCDs, LEDs, and everything in between. Along with a variety of touchscreens, HDMI displays, eInks and screens from tiny 0.96" OLEDs up to our full color 10" Pixel Qi displays, we also offer unique & useful products like these Adjustable Wire Stands.

Adafruit FeatherWing OLED - 128x64 OLED Add-on For Feather - STEMMA QT / Qwiic

PRODUCT ID: 4650

A Feather board without ambition is a Feather board without FeatherWings! This is the FeatherWing 128x64 OLED : it adds a gorgeous 128x64...

A Feather board without ambition is a Feather board without FeatherWings! This is the FeatherWing 128x64 OLED : it adds a gorgeous 128x64 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight! These displays are small, only about 1.3" diagonal,...

$14.95

IN STOCK

Monochrome 1.3" 128x64 OLED graphic display - STEMMA QT / Qwiic

PRODUCT ID: 938

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of...

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$19.95

IN STOCK

Adafruit PiOLED - 128x32 Monochrome OLED Add-on for Raspberry Pi

PRODUCT ID: 3527

If you're looking for the most compact li'l display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the...

If you're looking for the most compact li'l display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit 128x32 PiOLED is your little OLED pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The PiOLED comes with a monochrome 128x32 OLED, with sharp white pixels. The OLED uses only the I2C pins so you have plenty of GPIO connections...

$14.95 $7.99

IN STOCK

TFT breakout wired to arduino, hand drawing a cursive hello using touchscreen

3.5" TFT 320x480 + Touchscreen Breakout Board w/MicroSD Socket - HXD8357D

PRODUCT ID: 2050

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (3.5" diagonal) bright (6 white-LED backlight)...

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (3.5" diagonal) bright (6 white-LED backlight) and colorful! 480x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display, and double our 2.8" TFT. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen. This...

$39.95

IN STOCK

Angled shot of 1.3" OLED display module.

Monochrome 1.3" 128x64 SH1106G SPI OLED Monochrome Display

PRODUCT ID: 5228

This is a screen for advanced hackers who like the look of the OLED screen we've put into the Adafruit MACROPAD RP2040. This is just the...

This is a screen for advanced hackers who like the look of the OLED screen we've put into the Adafruit MACROPAD RP2040. This is just the raw display module - no PCB or supporting circuitry is included! You'll need to add a 12V boost converter and other components to make it work. Check out the MACROPAD PCB files for a place to start. We're selling this module bare for those who want to integrate it into their own project or...

$6.50

1 IN STOCK

DIY HDMI Cable Parts - Right Angle (R bend) HDMI Plug Adapter

PRODUCT ID: 3549

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to...

$6.50

IN STOCK

Mini HDMI Plug to Standard HDMI Jack Adapter

PRODUCT ID: 2819

What an adorable little pug! Sorry - plug! What an adorable mini HDMI to HDMI plug. We find this plug adapter really helpful....

What an adorable little pug! Sorry - plug! What an adorable mini HDMI to HDMI plug. We find this plug adapter really helpful. It's a great way to convert any mini HDMI plug to a normal HDMI plug and...that's about it! Now you can use any of your classic HDMI cables. Simple. Useful. Adorable. Note: This product may come in black or white. They are functionally the same. We cannot control...

$2.95

94 IN STOCK

Adafruit 1.69" 280x240 Round Rectangle Color IPS TFT Display - ST7789

PRODUCT ID: 5206

Don't be such a square - throw a curve-ball into your electronics with a curved-edge miniature display. Here's a new "round rect"...

Don't be such a square - throw a curve-ball into your electronics with a curved-edge miniature display. Here's a new "round rect" TFT display - it's 1.69" diagonal and has a high-density 220 ppi, 280x240 full color pixels with IPS any-angle viewing. We've seen displays of this caliber used in smartwatches and small electronic devices but they've always been MIPI interface. Finally, we found one that is SPI...

$17.50

IN STOCK

Monochrome 0.96" 128x64 OLED Graphic Display - STEMMA QT

PRODUCT ID: 326

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64...

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$17.50

IN STOCK

HDMI 5" 800x480 Display Backpack - With Resistive Touchscreen

PRODUCT ID: 2260

Its a mini panel-mountable HDMI monitor with a built-in resistive touchscreen! So small and simple, you can use this display with any computer that...

Its a mini panel-mountable HDMI monitor with a built-in resistive touchscreen! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it easy to attach to a case or rail. This backpack features the TFP401 for decoding video, and includes the attached display so its plug-n-play. The TFP401 is a beefy DVI/HDMI decoder from TI. It can take unencrypted video and pipe out the raw 24-bit color pixel...

$74.95

53 IN STOCK

2.2" 18-bit color TFT LCD display with microSD card breakout

PRODUCT ID: 1480

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to...

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 2.2" display has 320x240 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are...

$24.95

IN STOCK

1.8" SPI TFT display, 160x128 18-bit color - ST7735R driver

PRODUCT ID: 618

We just love this little 1.8" TFT display, with true TFT color (up to 18-bits per pixel!), fine 160x128 resolution, two white LED backlight that...

We just love this little 1.8" TFT display, with true TFT color (up to 18-bits per pixel!), fine 160x128 resolution, two white LED backlight that runs on 3.3V and a very easy SPI interface that requires only 4 or 5 digital pins to send pixels to the display. Please note! This is just the raw display, not attached to a PCB or for use with a breadboard. If you want to use this out of the box with no surface mount soldering, check out our fully...

$9.95

IN STOCK

Adafruit Grayscale 1.5" 128x128 OLED Graphic Display - STEMMA QT / Qwiic

PRODUCT ID: 4741

This OLED goes out to all the fans who want more pixels ! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one...

This OLED goes out to all the fans who want more pixels ! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one is a whopping 128x128 pixels and it even has an extra bonus - it can do grayscale pixels! Yep, you get the same crispness of a monochrome OLED but with 16 levels of grayscale. This display is a petite 1.5" diagonal, but very readable due to the high contrast of an OLED display. This display is...

$22.50

IN STOCK

i2c / SPI character LCD backpack

PRODUCT ID: 292

LCD backpacks reduce the number of pins needed to connect to an LCD. LCDs are a fun and easy way to have your microcontroller project talk back to...

LCD backpacks reduce the number of pins needed to connect to an LCD. LCDs are a fun and easy way to have your microcontroller project talk back to you. Character LCDs are common, and easy to get, available in tons of colors and sizes. We've written tutorials on using character LCDs with an Arduino (or similar microcontroller) but find that the number of pins necessary to control the LCD can be restrictive, especially with ambitious projects....

$9.95

IN STOCK

Character LCD with 16x2 characters, with header and potentiometer

Standard LCD 16x2 + extras - white on blue

PRODUCT ID: 181

Standard HD44780 LCDs are useful for creating standalone projects. 16 characters wide, 2 rowsWhite text on blue backgroundConnection port is...

Standard HD44780 LCDs are useful for creating standalone projects. 16 characters wide, 2 rowsWhite text on blue backgroundConnection port is 0.1" pitch, single row for easy breadboarding and wiringPins are documented on the back of the LCD to assist in wiring it upSingle LED backlight included can be dimmed easily with a resistor or PWM and uses much less power than LCD with EL (electroluminescent) backlightsCan be fully controlled with...

$9.95

IN STOCK

MagTag dev board with enclosure pieces, four magnet feet, and lipoly battery

Adafruit MagTag Starter Kit - ADABOX017 Essentials

PRODUCT ID: 4819

The Adafruit MagTag combines the new ESP32-S2 wireless module and a 2.9" grayscale E-Ink display to make a low-power IoT display that can show...

The Adafruit MagTag combines the new ESP32-S2 wireless module and a 2.9" grayscale E-Ink display to make a low-power IoT display that can show data on its screen even when power is removed! The ESP32-S2 is great because it builds on the years of code and support for the ESP32 and also adds native USB support so you can use this board with Arduino or CircuitPython! And of course, the Mag in MagTag stands for magnetic . We...

$44.95

69 IN STOCK

RGB backlight negative LCD 16x2 + extras - RGB on black

PRODUCT ID: 399

This is a fancy upgrade to standard 16x2 LCDs, instead of just having blue and white, or red and black, this LCD has full color RGB characters on a...

This is a fancy upgrade to standard 16x2 LCDs, instead of just having blue and white, or red and black, this LCD has full color RGB characters on a dark/black background! That means you can change the character display colors to anything you want - red, green, blue, pink, white, purple yellow, teal, salmon, chartreuse. This LCD looks strikingly good in person We had these custom made to our specification so that you can use them in existing LCD...

$13.95

IN STOCK

Monochrome 0.91" 128x32 I2C OLED Display - STEMMA QT / Qwiic

PRODUCT ID: 4440

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32...

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$12.50

IN STOCK

Mini HDMI to HDMI Cable - 5 feet

PRODUCT ID: 2775

Connect a device with a Mini HDMI port to a regular sized HDMI port together with this basic HDMI cable. It has nice molded grips for easy...

Connect a device with a Mini HDMI port to a regular sized HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long (about 5 feet). Perfect for use with your new Raspberry Pi Zero!

$5.95

IN STOCK

Front of E-Ink display with monochrome graphic and "2.13 inch E-Ink Monochrome" text

Adafruit 2.13" Monochrome eInk / ePaper Display with SRAM - 250x122 Monochrome with SSD1680

PRODUCT ID: 4197

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a monochromatic eInk display....

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a monochromatic eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight...

$22.50

73 IN STOCK

DIY HDMI Cable Parts - Straight Micro HDMI Plug Adapter

PRODUCT ID: 3556

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Micro HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

$6.50

IN STOCK

Angled shot of Adafruit MagTag development board with ESP32-S2 and E-Ink display.

Adafruit MagTag - 2.9" Grayscale E-Ink WiFi Display

PRODUCT ID: 4800

The Adafruit MagTag combines the new ESP32-S2 wireless module and a 2.9" grayscale E-Ink display to make a low-power IoT display that can show...

The Adafruit MagTag combines the new ESP32-S2 wireless module and a 2.9" grayscale E-Ink display to make a low-power IoT display that can show data on its screen even when power is removed! The ESP32-S2 is great because it builds on the years of code and support for the ESP32 and also adds native USB support so you can use this board with Arduino or CircuitPython! We designed this board to be low-power friendly - with a spot for a 350 or...

$34.95

69 IN STOCK

TFT breakout wired up on breadboard, showing colorful image of friendly owl

Adafruit 1.14" 240x135 Color TFT Display + MicroSD Card Breakout - ST7789

PRODUCT ID: 4383

Say hello to our 1.14" 240x135 Color TFT Display w/ MicroSD Card Breakout – we think it's T - F - T errific! It's the size of your...

Say hello to our 1.14" 240x135 Color TFT Display w/ MicroSD Card Breakout – we think it's T - F - T errific! It's the size of your thumbnail, with glorious 240x135 high res pixel color. This very very small display is only 1.14" diagonal, packed with RGB pixels, for making very small high-density displays. We've been looking for a display like this for a long time - it's so small only 1.14" diagonal but has a...

$14.95

IN STOCK

DIY HDMI Cable Parts - Right Angle (R Bend) Micro HDMI Plug

PRODUCT ID: 3557

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) Micro HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop...

$6.50

IN STOCK

HDMI 5" Display Backpack - Without Touch

PRODUCT ID: 2232

Its a mini panel-mountable HDMI monitor! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it...

Its a mini panel-mountable HDMI monitor! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it easy to attach to a case or rail. This backpack features the TFP401 for decoding video, and includes the attached display so its plug-n-play. The TFP401 is a beefy DVI/HDMI decoder from TI. It can take unencrypted video and pipe out the raw 24-bit color pixel data - HDCP not supported! The 5"...

$59.95

IN STOCK

Bare Television TFT Display with Receiver board and RCA connector

NTSC/PAL (Television) TFT Display - 2.0" Diagonal

PRODUCT ID: 911

Yes, this is an adorable miniature television! The visible display measures only 2.0" diagonal, the TFT comes with a NTSC/PAL driver board. The...

Yes, this is an adorable miniature television! The visible display measures only 2.0" diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-12VDC to the red and black wires, then connect a composite video source to the yellow and black wire. Voila, a television display! There's a little button to adjust the LED backlight brightness (5 levels) - there is no other adjustment available but...

$39.95

IN STOCK

TFT breakout wired to arduino, hand doodling using touchscreen

2.8" TFT LCD with Cap Touch Breakout Board w/MicroSD Socket

PRODUCT ID: 2090

Add some jazz & pizazz to your project with a color capactive touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4...

Add some jazz & pizazz to your project with a color capactive touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a capacitive single-touch touchscreen attached to it already, so you can detect finger presses anywhere on the screen. (We...

$39.95

96 IN STOCK

Character LCD with 20x4 characters, with header and potentiometer

Standard LCD 20x4 + extras - white on blue

PRODUCT ID: 198

Standard HD44780 LCDs are useful for creating standalone projects. 20 characters wide, 4 rowsWhite text on blue backgroundConnection port is...

Standard HD44780 LCDs are useful for creating standalone projects. 20 characters wide, 4 rowsWhite text on blue backgroundConnection port is 0.1" pitch, single row for easy breadboarding and wiringSingle LED backlight with a resistor included, you can power it directly from 5V. If it's too bright for you, it can be dimmed easily with a resistor or PWM and uses much less power than LCD with EL (electroluminescent) backlightsCan be fully...

$17.95

IN STOCK

TFT display with purple flower on screen

Adafruit 1.44" Color TFT LCD Display with MicroSD Card breakout - ST7735R

PRODUCT ID: 2088

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to...

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.44" display has 128x128 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are...

$14.95

IN STOCK

Character LCD with 16x2 characters, with header soldered on

Assembled Standard LCD 16x2 + extras - White on Blue

PRODUCT ID: 1447

Standard HD44780 LCDs are useful for creating standalone projects. This product is similar to our Standard LCD 16x2 display but comes with the...

Standard HD44780 LCDs are useful for creating standalone projects. This product is similar to our Standard LCD 16x2 display but comes with the header soldered on! 16 characters wide, 2 rowsWhite text on blue backgroundConnection port is 0.1" pitch, single row for easy breadboarding and wiringPins are documented on the back of the LCD to assist in wiring it upSingle LED backlight included can be dimmed easily with a resistor or PWM...

$10.95

IN STOCK

Adafruit USB + Serial LCD Backpack Add-On PCB

Adafruit USB + Serial LCD Backpack Add-On with Cable

PRODUCT ID: 781

Adding a character display to your project or computer has never been easier with the new Adafruit USB or TTL serial backpack! This custom-designed...

Adding a character display to your project or computer has never been easier with the new Adafruit USB or TTL serial backpack! This custom-designed PCB can connect to the back of any 16x2 or 20x4 character LCD and does everything you could want: printing text, automatic scrolling, setting the backlight, adjusting contrast, making custom characters, turning on and off the cursor, etc. It can even handle our RGB backlight LCDs with full 8-bit PWM...

$12.95

IN STOCK

Small Liquid Crystal Light Valve - Controllable Shutter Glass

PRODUCT ID: 3627

What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a...

What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a LCD Controllable Black-out Panel)! They're often used for electric welding helmets because they can protect the welder's eyes from the bright sparks. Or – if you aren't a welder – they can be used to provide a "reveal" effect for your...

$2.95

IN STOCK

TFT breakout wired to arduino, hand drawing a heart using touchscreen

3.2" TFT LCD with Touchscreen Breakout Board w/MicroSD Socket - ILI9341

PRODUCT ID: 1743

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is really big (3.2" diagonal) bright (6 white-LED...

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is really big (3.2" diagonal) bright (6 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen. This display has a...

$29.95

IN STOCK

32x32 RGB LED Matrix Panel - 4mm Pitch

PRODUCT ID: 607

Bring a little bit of Times Square into your home with this totally adorable 5 inch square 32 x 32 RGB LED matrix panel. These panels are normally...

Bring a little bit of Times Square into your home with this totally adorable 5 inch square 32 x 32 RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips. We thought they looked really cool so we picked up a few boxes of them from a factory. They have 1024 bright RGB LEDs arranged in a 32x32 grid on the front with 4mm...

$29.95

IN STOCK

Bare rectangular TFT display with flex connector

5.0" 40-pin TFT Display - 800x480 with Touchscreen

PRODUCT ID: 1596

This 5.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need...

This 5.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer electronics, such as miniature TV's, GPS's, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability. This version has a 4-wire...

$39.95

IN STOCK

Angled shot of the Straight HDMI Plug Adapter

DIY HDMI Cable Parts - Straight HDMI Plug Adapter

PRODUCT ID: 3548

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your very...

$6.50

IN STOCK

RGB backlight negative LCD 20x4 + extras - RGB on black

PRODUCT ID: 498

This is a fancy upgrade to standard 20x4 LCDs, instead of just having blue and white, or red and black, this LCD has full color RGB characters on a...

This is a fancy upgrade to standard 20x4 LCDs, instead of just having blue and white, or red and black, this LCD has full color RGB characters on a dark/black background! That means you can change the character display colors to anything you want - red, green, blue, pink, white, purple yellow, teal, salmon, chartreuse. This LCD looks strikingly good in person One nice thing about these LCDs is that they are an elegant upgrade, but you can use...

$24.95

55 IN STOCK

Adafruit 128x64 OLED Bonnet for Raspberry Pi

PRODUCT ID: 3531

If you'd like a compact display, with buttons and a joystick - we've got what you're looking for. The Adafruit 128x64 OLED Bonnet for...

If you'd like a compact display, with buttons and a joystick - we've got what you're looking for. The Adafruit 128x64 OLED Bonnet for Raspberry Pi is the big sister to our mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger screen besides. With the OLED display in the center, we had some space on either side so we added a 5-way joystick and two pushbuttons. Great for when you want to have a...

$22.50

IN STOCK

Adafruit MONSTER M4SK - DIY Electronic Eyes Mask

PRODUCT ID: 4343

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER...

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER M4SK is like the Hallowing but twice as good, with two gorgeous 240x240 pixel IPS TFT displays, driven by a 120MHZ Cortex M4 processor that can pump out those pixels super fast. You'll get the same quality display as our Raspberry Pi Eyes kit but without needing to tote around a full Linux...

$44.95

22 IN STOCK

1.54" 240x240 Color IPS TFT Display

PRODUCT ID: 4421

This is a screen for advanced hackers who like the look of the TFT screen we've put into the TFT Gizmo and Monster M4sk. The 1.54" display...

This is a screen for advanced hackers who like the look of the TFT screen we've put into the TFT Gizmo and Monster M4sk. The 1.54" display has 240x240 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well. This is just the display module! No PCB is included!...

$14.95

IN STOCK

Raspberry Pi computer with E-Ink bonnet attached, displaying weather

Adafruit 2.13" Monochrome E-Ink Bonnet for Raspberry Pi - THINK INK

PRODUCT ID: 4687

Easy e-paper finally comes to Raspberry Pi, with this bonnet that's designed to make it a breeze to add a 2.13" 250x122 crisp...

Easy e-paper finally comes to Raspberry Pi, with this bonnet that's designed to make it a breeze to add a 2.13" 250x122 crisp monochromic eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and...

$19.95

58 IN STOCK

16x32 RGB LED matrix panel with colorful text lit up

Medium 16x32 RGB LED matrix panel - 6mm Pitch

PRODUCT ID: 420

Bring a little bit of Times Square into your home with this 16 x 32 RGB LED matrix panel. These panels are normally used to make video walls, here in...

Bring a little bit of Times Square into your home with this 16 x 32 RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips. We thought they looked really cool so we picked up a few boxes of them from a factory. They have 512 bright RGB LEDs arranged in a 16x32 grid on the front. On the back there is a PCB with two IDC...

$24.95

IN STOCK

Monochrome 0.91" OLED module with white text

Monochrome 128x32 SPI OLED graphic display

PRODUCT ID: 661

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32...

$17.50

50 IN STOCK

HDMI 4 Pi: 7" Display no Touchscreen 800x480 - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1934

Make a lovely video setup with a 7" screen at 800x480 resolution . For this model, we tried to get an inexpensive 800x480 display that was still...

Make a lovely video setup with a 7" screen at 800x480 resolution . For this model, we tried to get an inexpensive 800x480 display that was still high quality and would be good for embedded computing usage. The visible display measures 7" diagonal and is a 'raw TTL' display, the model has an extra-bright backlight that looks much better than other 7" TFTs we've tested. We include a driver board with HDMI, VGA and...

$74.95

9 IN STOCK

2.8" TFT LCD with Touchscreen Breakout Board w/MicroSD Socket - ILI9341

PRODUCT ID: 1770

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight)...

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen. We also have a version of this...

$29.95

IN STOCK

OLED Breakout Board - 16-bit Color 1.5" w/microSD holder

PRODUCT ID: 1431

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our big 1.5" color OLED displays are...

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our big 1.5" color OLED displays are perfect when you need a small display with vivid, high-contrast 16-bit color. The visible portion of the OLED measures 1.5" diagonal and contains 128x128 RGB pixels, each one made of red, green and blue OLEDs. Each pixel can be set with 16-bits of resolution for a large range of colors. Because...

$39.95

58 IN STOCK

DIY HDMI Cable Parts - Straight HDMI Socket Adapter

PRODUCT ID: 3551

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight HDMI socket . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your very...

$6.50

IN STOCK

Adafruit 1.3" 240x240 Wide Angle IPS TFT Display

PRODUCT ID: 4520

This is a screen for advanced hackers who like the look of the TFT screen we've put into the Adafruit CLUE and Adafruit Mini PiTFT 1.3". The...

This is a screen for advanced hackers who like the look of the TFT screen we've put into the Adafruit CLUE and Adafruit Mini PiTFT 1.3". The 1.3" display has 240x240 16-bit full-color pixels and is an IPS display, so the color looks great up to 80 degrees off-axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well. This is just the display module! No...

$12.50

IN STOCK

Adafruit HalloWing M0 Express

PRODUCT ID: 3900

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Are you the kind of person who doesn't like taking down the skeletons and...

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Are you the kind of person who doesn't like taking down the skeletons and spiders until after January? Well, we've got the development board for you. This is electronics at its most spooky! The Adafruit HalloWing is a skull-shaped ATSAMD21 board with a ton of extras built in to make for an adorable wearable, badge, development kit, or the engine...

$34.95

90 IN STOCK

RA8875 Driver Board for 40-pin TFT Touch Displays with loose header

RA8875 Driver Board for 40-pin TFT Touch Displays - 800x480 Max

PRODUCT ID: 1590

Have you gazed longingly at large TFT displays - you know what I'm talking about here, 4", 5" or 7" TFTs with up to 800x480...

Have you gazed longingly at large TFT displays - you know what I'm talking about here, 4", 5" or 7" TFTs with up to 800x480 pixels. Then you look at your Arduino. You love your Arduino (you really do!) but there's no way it can control a display like that, one that requires 60Hz refresh and 4 MHz pixel clocking. Heck, it doesn't even have enough pins. I suppose you could move to ARM core processors with TTL display...

$39.95

IN STOCK

TFT breakout wired up on breadboard, showing colorful image of friendly robot

2.0" 320x240 Color IPS TFT Display with microSD Card Breakout

PRODUCT ID: 4311

This gorgeous IPS display breakout is the best way to add a small, colorful and bright display to any project, with excellent visibility from any...

This gorgeous IPS display breakout is the best way to add a small, colorful and bright display to any project, with excellent visibility from any angle. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 2.0" display has 320x240 color pixels. Unlike the low cost "Nokia...

$19.95

66 IN STOCK

DIY HDMI Cable Parts - Straight Mini HDMI Plug Adapter

PRODUCT ID: 3552

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Mini HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

$6.50

IN STOCK

Assembled backpack on LCD with purple backlight and text "USB/Serial LCD Backpack"

USB + Serial Backpack Kit with 16x2 RGB backlight negative LCD - RGB on Black

PRODUCT ID: 784

Adding a character display to your project or computer has never been easier with the new Adafruit USB or TTL serial backpack! This custom-designed...

Adding a character display to your project or computer has never been easier with the new Adafruit USB or TTL serial backpack! This custom-designed PCB sits on the back of our 'standard' character LCD (16x2 or 20x4 sized) and does everything you could want: printing text, automatic scrolling, setting the backlight, adjusting contrast, making custom characters, turning on and off the cursor, etc. It can even handle our RGB backlight LCDs...

$24.95

IN STOCK

Adafruit TFT FeatherWing - 3.5" 480x320 Touchscreen for Feathers

PRODUCT ID: 3651

Spice up your Feather project with a beautiful 3.5" touchscreen display shield with built in microSD card socket. This TFT display is 3.5"...

Spice up your Feather project with a beautiful 3.5" touchscreen display shield with built in microSD card socket. This TFT display is 3.5" diagonal with a bright 6 white-LED backlight. You get a massive 480x320 pixels with individual 16-bit color pixel control. It has way more resolution than a black and white 128x64 display, and twice as much as our 2.4" TFT FeatherWing. As a bonus, this display comes with a resistive touchscreen...

$39.95

56 IN STOCK

TFP401 HDMI/DVI Decoder to 40-Pin TTL Breakout - With Touch

PRODUCT ID: 2219

It's a mini HDMI decoder board! So small and simple, you can use this board as an all-in-one display driver for TTL displays, or perhaps decoding...

It's a mini HDMI decoder board! So small and simple, you can use this board as an all-in-one display driver for TTL displays, or perhaps decoding HDMI/DVI video for some other project. This breakout features the TFP401 for decoding video, and for the touch version, an AR1100 USB resistive touch screen driver. The TFP401 is a beefy DVI/HDMI decoder from TI. It can take unencrypted video and pipe out the raw 24-bit color pixel data - HDCP not...

$29.95

IN STOCK

Front of E-Ink display with monochrome graphic and "1.54 inch E-Ink Monochrome" text

Adafruit 1.54" Monochrome eInk / ePaper Display with SRAM - 200x200 with SSD1681

PRODUCT ID: 4196

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a eInk display. Chances are...

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight readable. It really...

$24.95

61 IN STOCK

2.8" TFT Display - 240x320 with Capacitive Touchscreen

PRODUCT ID: 2770

Add some jazz & pizzazz to your project with a color capacitive touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4...

Add some jazz & pizzazz to your project with a color capacitive touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a capacitive single-touch touchscreen attached to it already, so you can detect finger presses anywhere on the...

$37.95

20 IN STOCK

Circuit Playground TFT Gizmo - Bolt-on Display + Audio Amplifier

PRODUCT ID: 4367

Extend and expand your Circuit Playground projects with a bolt on TFT Gizmo that lets you add a lovely color display in a sturdy and reliable...

Extend and expand your Circuit Playground projects with a bolt on TFT Gizmo that lets you add a lovely color display in a sturdy and reliable fashion. This PCB looks just like a round TFT breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Once attached you'll get a 1.54" 240x240 IPS display with backlight control, two 3-pin STEMMA connectors for attaching NeoPixel strips or servos, and a...

$19.95

IN STOCK

Adafruit 1.54" 240x240 Wide Angle TFT LCD Display with MicroSD - ST7789

PRODUCT ID: 3787

We've been looking for a display like this for a long time - it's only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel...

We've been looking for a display like this for a long time - it's only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like our 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We've seen displays of this caliber used in smartwatches and small electronic devices but they've always been MIPI interface. Finally, we found one that is...

$24.95

IN STOCK

Adafruit 2.4" TFT LCD with Touchscreen Breakout w/MicroSD Socket - ILI9341

PRODUCT ID: 2478

Add some jazz & pizzazz to your project with a color touchscreen LCD. This TFT display is 2.4" diagonal with a bright (4 white-LED)...

Add some jazz & pizzazz to your project with a color touchscreen LCD. This TFT display is 2.4" diagonal with a bright (4 white-LED) backlight and it's colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen. If you need a larger...

$29.95

95 IN STOCK

Adafruit 1.3" Color TFT Bonnet for Raspberry Pi - 240x240 TFT + Joystick Add-on

PRODUCT ID: 4506

If you'd like a compact color display, with buttons and a joystick - we've got what you're looking for. The Adafruit 1.3" Color TFT...

If you'd like a compact color display, with buttons and a joystick - we've got what you're looking for. The Adafruit 1.3" Color TFT Bonnet for Raspberry Pi is the big sister to our mini PiTFT add-ons. This bonnet has 240x240 color pixels in an IPS TFT display controlled over SPI. This display is super small, only about 1.3" diagonal, but since it is an IPS display, it's very readable with high contrast and...

$17.50

37 IN STOCK

Adafruit 1.3" 240x240 Wide Angle TFT LCD Display with MicroSD - ST7789

PRODUCT ID: 4313

We've been looking for a display like this for a long time - it's so small only 1.3" diagonal but has a high density 260 ppi, 240x240...

We've been looking for a display like this for a long time - it's so small only 1.3" diagonal but has a high density 260 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like our 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We've seen displays of this caliber used in smartwatches and small electronic devices but they've always been MIPI interface. Finally, we found one...

$16.95

IN STOCK

2.9" Flexible 296x128 Monochrome eInk / ePaper Display - UC8151D Chipset

PRODUCT ID: 4262

Woah, the cyber-future is here! Flexible E-Ink has been demo'd at high tech events for years but now you can actually get your paws on it. This...

Woah, the cyber-future is here! Flexible E-Ink has been demo'd at high tech events for years but now you can actually get your paws on it. This display is true E-Ink / E-Paper, once an image is displayed it will stay even once you remove all power. The image is also high contrast and very daylight readable. It really does look just like printed paper! This flexible display sports a 2.9" monochrome (black and white) display ....

$24.95

11 IN STOCK

Adafruit 2.9" Grayscale eInk / ePaper Display FeatherWing - 4 Level Grayscale

PRODUCT ID: 4777

Easy e-paper comes to your Feather with this breakout that's designed to make it a breeze to add a monochrome eInk display....

Easy e-paper comes to your Feather with this breakout that's designed to make it a breeze to add a monochrome eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight...

$22.50

IN STOCK

Adafruit eInk Breakout Friend with large E-Ink display attached, wired to Feather

Adafruit eInk Breakout Friend with 32KB SRAM

PRODUCT ID: 4224

Add some bi-stability to your life with an Adafruit EInk Breakout Friend - your fun pal who's happy to lend a hand when you want to work with...

Add some bi-stability to your life with an Adafruit EInk Breakout Friend - your fun pal who's happy to lend a hand when you want to work with EInk/E-Paper displays. Luckily for us, just about every small-medium size EInk display made these days has a standard 24-pin connection. This breakout will add all the power supply support circuitry and level shifting so you can attach your favorite display (up to tri-color 4.2") and wire it up to...

$8.50

IN STOCK

Adafruit 2.23" Monochrome OLED Bonnet for Raspberry Pi

PRODUCT ID: 4567

If you're looking for a bright, readable OLED display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you...

If you're looking for a bright, readable OLED display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit 2.23" Monochrome OLED Bonnet for Raspberry Pi is your chonky OLED pal, ready to snap onto any and all Raspberry Pi computers, to give you a vivid display. The Bonnet comes with a 2.13" diagonal monochrome 128x32 OLED, with sharp white pixels. The OLED the I2C pins plus...

$22.50

75 IN STOCK

Adafruit 1.8" Color TFT Shield w/microSD and Joystick - v 2

PRODUCT ID: 802

This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout...

This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board and remixed it into an Arduino shield complete with microSD card slot and a 5-way joystick navigation switch and three selection buttons! Since the display uses only 4 pins to communicate and has its own pixel-addressable frame buffer, it can be used easily to add a display & interface without...

$34.95

49 IN STOCK

Adjustable Bent-Wire Stand for up to 7 Tablets and Small Screens

Adjustable Bent-Wire Stand - up to 7" Tablets and Small Screens

PRODUCT ID: 1679

This handy bent-wire display stand was originally designed to hold up 7" tablets but the rubberized design is great for general purpose...

This handy bent-wire display stand was originally designed to hold up 7" tablets but the rubberized design is great for general purpose electronics & TFT holding. We use it to hold up our HDMI displays while connected to a Pi - even though it is meant for 7" we found that its fine for 5" to 10" TFTs since they're not as heavy as a tablet. You can adjust the angle and collapse it for travel. iPad mini, screen and...

$4.95

IN STOCK

Shot of a work station shelf populated with electronic tools and a clear glass head filled with glowing LED strips. The eInk clock sits below reading the time, temperature, and humidity.

Bluetooth eInk Display Clock with Temperature Humidity Sensor - LYWSD02

PRODUCT ID: 5023

Here is a jolly cute Bluetooth-enabled sensor-and-digital-clock to monitor your room's temperature and humidity. Only 110mm x 55mm, we dig its...

Here is a jolly cute Bluetooth-enabled sensor-and-digital-clock to monitor your room's temperature and humidity. Only 110mm x 55mm, we dig its medium-size form factor and minimal design. The shell is made of durable ABS material. Upfront you get a 3.5" x 1.25" (87mm x 32mm) eInk display. These sensors are sold to work with the Mijia "Mi Home" App (iOS and Android) - they...

$29.95

IN STOCK

2.13" Flexible Monochrome eInk / ePaper Display - 212x104 Monochrome

PRODUCT ID: 4243

Woah, the cyber-future is here! Flexible E-Ink has been demo'd at high tech events for years but now you can actually get your paws on it. This...

$17.50

7 IN STOCK

Monochrome 2.7 128x64 OLED Graphic Display Module showing white text

Monochrome 2.7" 128x64 OLED Graphic Display Module Kit

PRODUCT ID: 2674

If you've been diggin' our monochome OLEDs but need something bigger, this display will delight you. These displays are 2.7" diagonal,...

If you've been diggin' our monochome OLEDs but need something bigger, this display will delight you. These displays are 2.7" diagonal, and very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is...

$49.95

IN STOCK

Qualia Bare Driver Board for LP097QX1 Display

PRODUCT ID: 1716

The Qualia Retina driver board is a work of art (it was designed by resident engineer KTOWN). It's used in the Adafruit Qualia 9.7"...

The Qualia Retina driver board is a work of art (it was designed by resident engineer KTOWN). It's used in the Adafruit Qualia 9.7" DisplayPort Monitor Kit and we use the really awesome LT3754 as a 12-channel constant current driver with individual backlight string channel control. This gives the backlight perfect consistency over any usage or temperature range. A ATtiny85 handles the backlight dimming and soft on/off, so you can PWM...

$79.95

2 IN STOCK

Circuit Playground 200x200 Tri-Color E-Ink Gizmo - E-Ink Display + Audio Amplifier

PRODUCT ID: 4869

Extend and expand your Circuit Playground projects with a bolt-on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and...

Extend and expand your Circuit Playground projects with a bolt-on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and reliable fashion. This PCB looks just like a round E-Ink breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper...

$21.95

36 IN STOCK

16x24 Red LED Matrix Panel - Chainable HT1632C Driver

PRODUCT ID: 555

These LED panels take care of all the work of making a big matrix display. Each panel has six 8x8 red matrix modules, for a 16x24 matrix. The panel...

These LED panels take care of all the work of making a big matrix display. Each panel has six 8x8 red matrix modules, for a 16x24 matrix. The panel has a HT1632C chip on the back with does all the multiplexing work for you and has a 3-pin SPI-like serial interface to talk to it and set LEDs on or off (you cannot set the LED to be individually dimmed, as in 'grayscale'). There's a few extras as well, such as being able to change the...

$24.95

64 IN STOCK

40-pin TFT Friend - FPC Breakout with LED Backlight Driver

PRODUCT ID: 1932

This breakout board is something we designed in-house to help us work with 'dot-clock' 40-pin TFT displays that require the RGB pixel data to...

This breakout board is something we designed in-house to help us work with 'dot-clock' 40-pin TFT displays that require the RGB pixel data to be clocked in continuously. These displays have 40-pin Flex PCB (FPC) cables and often require a boost converter for the backlight LED, which makes them annoying to breadboard. To make them breadboardable, we stuck a 40-pin FPC and a FAN5333-based backlight driver with adjustable current onto a...

$9.95

IN STOCK

Adafruit 2.9" Tri-Color eInk / ePaper Display FeatherWing - Red Black White

PRODUCT ID: 4778

Easy e-paper comes to your Feather with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are...

Easy e-paper comes to your Feather with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight readable. It...

$24.95

15 IN STOCK

DIY HDMI Cable Parts - Straight Micro HDMI Socket Adapter

PRODUCT ID: 3559

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Micro HDMI socket . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

$6.50

5 IN STOCK

LG LP097QX1 - iPad 3/4 Retina Display

PRODUCT ID: 1751

These are the same glorious 2048x1536 retina-blasting, ultra-high pixel density, IPS displays you may have seen in iPad 3 or 4's. This product...

These are the same glorious 2048x1536 retina-blasting, ultra-high pixel density, IPS displays you may have seen in iPad 3 or 4's. This product comes with only the brand new 9.7" diagonal TFT display module, no driver thunderbolt connector! We also sell a Qualia driver and a full kit with our Adafruit Qualia 9.7" DisplayPort Monitor Kit. This part is for advanced users, we suggest our monitor kit for most people. This display will...

$99.95

24 IN STOCK

DIY HDMI Cable Parts - Right Angle (R bend) Mini HDMI Plug

PRODUCT ID: 3553

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) Mini HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop...

$6.50

IN STOCK

HDMI 7" 800x480 Display Backpack - With Touchscreen

PRODUCT ID: 2407

Its a mini panel-mountable HDMI monitor with a built-in touchscreen! So small and simple, you can use this display with any computer that has HDMI...

Its a mini panel-mountable HDMI monitor with a built-in touchscreen! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it easy to attach to a case or rail. This backpack features the TFP401 for decoding video, and includes the attached display so its plug-n-play. The TFP401 is a beefy DVI/HDMI decoder from TI. It can take unencrypted video and pipe out the raw 24-bit color pixel data - HDCP...

$89.95

IN STOCK

OLED Breakout Board - 16-bit Color 0.96" w/microSD holder

PRODUCT ID: 684

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our new 0.96" color OLED displays are...

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our new 0.96" color OLED displays are perfect when you need an ultra-small display with vivid, high-contrast 16-bit color. The visible portion of the OLED measures 0.96" diagonal and contains 96x64 RGB pixels, each one made of red, green and blue OLEDs. Each pixel can be set with 16-bits of resolution for a large range of colors....

$29.95

68 IN STOCK

DIY HDMI Cable Parts - Right Angle (L Bend) Micro HDMI Plug

PRODUCT ID: 3558

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (L) Micro HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft...

$6.50

IN STOCK

Assembled Pycom WiPy 3.0 with Headers - MicroPython IoT Expansion Board

PRODUCT ID: 4815

Pycom's WiPy 3.0 – a tiny MicroPython-enabled WiFi & Bluetooth IoT development platform. With a 1KM WiFi range, state...

Pycom's WiPy 3.0 – a tiny MicroPython-enabled WiFi & Bluetooth IoT development platform. With a 1KM WiFi range, state of the art Espressif ESP32 chipset, and dual processor, the WiPy is all about taking the Internet of Things to the next level. Create and connect your things everywhere. Fast. Now comes pre-soldered , so no need to power up your soldering station! We also have some without headers...

$29.95

3 IN STOCK

Pimoroni HDMI 8" IPS LCD Screen Kit - 1024x768

PRODUCT ID: 4338

Make a gorgeous video set up with this high-resolution 8", IPS, 1024x768, plug-n-play HDMI screen kit with a display driver board...

Make a gorgeous video set up with this high-resolution 8", IPS, 1024x768, plug-n-play HDMI screen kit with a display driver board that's perfect for building into projects like arcade cabinets. The display's 4:3 aspect ratio makes it a great upgrade for retro gaming builds. Or simply use it as a big ol' dazzling display for your Raspberry Pi, or any computer with HDMI output. Comes with a cable and little...

$74.95

33 IN STOCK

Pimoroni Inky pHAT - 3 Color eInk Display - Yellow/Black/White

PRODUCT ID: 3933

What's that, you say? Pimoroni has another new super sweet tri-color e-paper display? Oh feast your eyes! This Inky pHat...

What's that, you say? Pimoroni has another new super sweet tri-color e-paper display? Oh feast your eyes! This Inky pHat in Yellow/Black/White is a petite 212x104 pixel three-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the...

$26.50

26 IN STOCK

7.0" 40-pin TFT Display - 800x480 without Touchscreen

PRODUCT ID: 2353

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, and an LED backlight. Its great for when you need a lot of space for graphics....

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, and an LED backlight. Its great for when you need a lot of space for graphics. These screens are commonly seen in consumer electronics, such as miniature TV's, GPS's, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability. This version does not have touchscreen attached It's exactly the same TFT...

$49.50

8 IN STOCK

24-pin eInk / ePaper Extension Cable connecting Featherwing to Tri-color display

24-pin eInk / ePaper Extension Cable 0.5mm Pitch - 25cm Long

PRODUCT ID: 4230

When you need more distance between you and your eInk display, use this 24-pin 0.5mm pitch FPC cable with an extender adapter to streeeeeeeeeetch it...

When you need more distance between you and your eInk display, use this 24-pin 0.5mm pitch FPC cable with an extender adapter to streeeeeeeeeetch it out. The cable is generic, but we recommend it for use with eInk because often folks want to mount the displays elsewhere. Just carefully pry open the connector on the eInk Friend , eInk Feather Friend , etc, and use this cable instead. Then connect the (not included) extender adapter between the...

$1.50

IN STOCK

Adafruit 2.13" Monochrome eInk / ePaper Display FeatherWing - 250x122 Monochrome with SSD1680

PRODUCT ID: 4195

Easy e-paper finally comes to your Feather, with this breakout that's designed to make it a breeze to add a monochrome eInk display. Chances...

Easy e-paper finally comes to your Feather, with this breakout that's designed to make it a breeze to add a monochrome eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight readable....

$22.50

IN STOCK

HDMI 7" 800x480 Display Backpack - Without Touch

PRODUCT ID: 2406

Its a mini panel-mountable HDMI monitor! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it...

$79.95

95 IN STOCK

Resistive Touchscreen Overlay - 7 diagonal

Resistive Touchscreen Overlay - 7" diag. 165mm x 105mm - 4 Wire

PRODUCT ID: 1676

If you already have a 7" TFT that is about 165mm x 105mm in size (with a visible area equal to or smaller than ~152mm x 91mm), you can put this...

If you already have a 7" TFT that is about 165mm x 105mm in size (with a visible area equal to or smaller than ~152mm x 91mm), you can put this glass resistive overlay over it to add a resistive touch screen. Note the 7" is the 'nominal' size - which fits many TFT's called 7" displays. Check the inner/outer dimensions in the technical specs to compare against your display. To use, first remove the protective plastic...

$14.95

IN STOCK

Acrylic Stand for 16x2 Character LCD

PRODUCT ID: 1365

Here is a mini-kit to get your 16x2 LCD standing up straight on your table. Made of 3mm black acrylic pieces, with 4 x 1" nylon screws & 4 x...

Here is a mini-kit to get your 16x2 LCD standing up straight on your table. Made of 3mm black acrylic pieces, with 4 x 1" nylon screws & 4 x nylon hex nuts, it goes together in a jiffy and looks super-spiffy! This product is designed specifically for our 16x2 USB/Serial backpacks. Our OLED 16x2 displays and RGB backlight positive and negative LCDs have slightly smaller screw holes so you'll have to drill them out to...

$4.95

IN STOCK

OLED Breakout Board - 16-bit Color 1.27" w/microSD holder

PRODUCT ID: 1673

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our 1.27" color OLED displays are...

We love our black and white monochrome displays but we also like to dabble with some color now and then. Our 1.27" color OLED displays are perfect when you need a small display with vivid, high-contrast 16-bit color. The visible portion of the OLED measures 1.27" diagonal and contains 128x96 RGB pixels, each one made of red, green and blue OLEDs. Each pixel can be set with 16-bits of resolution for a large range of colors. Because the...

$34.95

54 IN STOCK

Adafruit eInk Feather Friend with 32KB SRAM

PRODUCT ID: 4446

Easy e-paper finally comes to your Feather with this Adafruit EInk Feather Friend that's designed to make it a breeze to add an eInk...

Easy e-paper finally comes to your Feather with this Adafruit EInk Feather Friend that's designed to make it a breeze to add an eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight...

$8.95

19 IN STOCK

Adafruit 2.7" Tri-Color eInk / ePaper Display with SRAM - Red Black White

PRODUCT ID: 4098

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances...

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight readable....

$32.50

6 IN STOCK

Pi Supply PaPiRus Zero ePaper/eInk pHAT v1.2

PRODUCT ID: 3335

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero...

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero mini computer. ePaper / eInk is a display technology that mimics the appearance of ink on normal paper. Unlike conventional displays, ePaper reflects light – just like ordinary paper – and is capable of holding text and images indefinitely, even without electricity. Because of this,...

$34.95

15 IN STOCK

HDMI 4 Pi - 10.1" Display 1280x800 IPS - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1287

Yes, this is a beautiful bright 10.1" TFT display with incredibly high resolution and great angle-visibility! We tried to get the thinnest,...

Yes, this is a beautiful bright 10.1" TFT display with incredibly high resolution and great angle-visibility! We tried to get the thinnest, brightest, highest resolution display that would be good for embedded computing usage. The visible display measures 10" diagonal and is a 'raw' display as is used in a tablet, ultra thin with some mounting tabs around the edge. We include a driver board with HDMI, VGA and Composite inputs....

$144.95

89 IN STOCK

NTSC/PAL (Television) TFT Display - 1.5" Diagonal

PRODUCT ID: 910

Yes, this is an adorable miniature television! The visible display measures only 1.5" diagonal, the TFT comes with a NTSC/PAL driver board. The...

Yes, this is an adorable miniature television! The visible display measures only 1.5" diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-12VDC to the red and black wires, then connect a composite video source to the yellow and black wire. Voila, a television display! There's a little button to adjust the LED backlight brightness (5 levels) - there is no other adjustment available but...

$39.95

IN STOCK

DIY HDMI Cable Parts - Right Angle (L Bend) Mini HDMI Plug

PRODUCT ID: 3554

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (left bend) Mini HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop...

$6.50

33 IN STOCK

Monochrome 2.42" 128x64 OLED Graphic Display Module Kit

PRODUCT ID: 2719

If you've been diggin' our monochrome OLEDs but need something bigger, this display will delight you! These displays are 2.42"...

If you've been diggin' our monochrome OLEDs but need something bigger, this display will delight you! These displays are 2.42" diagonal , and very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to...

$39.95

IN STOCK

Pimoroni HDMI 10" IPS LCD Screen Kit - 1024x768

PRODUCT ID: 4337

Make a gorgeous video set up with this high-resolution 10", IPS, 1024x768, plug-n-play HDMI screen kit with a display driver board...

Make a gorgeous video set up with this high-resolution 10", IPS, 1024x768, plug-n-play HDMI screen kit with a display driver board that's perfect for building into projects like arcade cabinets. The display's 4:3 aspect ratio makes it a great upgrade for retro gaming builds. Or simply use it as a big ol' dazzling display for your Raspberry Pi, or any computer with HDMI output. Comes with a cable and...

$139.95

11 IN STOCK

Slim HDMI Cable - 900mm / 3 feet long

PRODUCT ID: 2421

Connect two HDMI devices together and save space with this slim, high quality HDMI cable. It has nice molded grips for easy installation and is...

Connect two HDMI devices together and save space with this slim, high quality HDMI cable. It has nice molded grips for easy installation and is 914mm long (~3 feet). Sporting a teeny 4mm diameter this cable stays out of your way! We also have slim HDMI cables at 450mm long and 1820mm long.

$12.50 $9.95

IN STOCK

E-Ink display connected to Feather, with image of friendly snake

Adafruit 2.13" HD Tri-Color eInk / ePaper Display FeatherWing - 250x122 RW Panel with SSD1680

PRODUCT ID: 4814

Easy e-paper comes to your Feather, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are...

Easy e-paper comes to your Feather, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight readable. It really...

$24.95

74 IN STOCK

Pimoroni Inky Tri-Color wHAT display refereshing itself

Pimoroni Inky wHAT (ePaper/eInk/EPD) - Red/Black/White

PRODUCT ID: 4143

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic paper...

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic paper displays to 4.2" glorious inches! Say hellooo to Inky wHAT ! You get 5x the number of pixels (400x300!) to use as an e-reader or maybe a weather display / calendar. Everything comes fully-assembled, so there's no soldering required! The display is securely plonked down to the Inky wHAT...

$64.95

15 IN STOCK

Large 3V Analog Panel Meter

PRODUCT ID: 3989

Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read...

Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read quickly. This Large 3V Panel Meter is about handheld-size, with one screw to open up the panel and replace the backing paper, if you like. Even though it's designed for analog signals, you can use it with digital signals too! Simply send it a PWM signal from a 3V logic microcontroller....

$9.95

11 IN STOCK

Large 5V Analog Panel Meter

PRODUCT ID: 3990

Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read...

Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read quickly. This Large 5V Analog Panel Meter is about handheld-size, with one screw to open up the panel and replace the backing paper, if you like. Even though it's designed for analog signals, you can use it with digital signals too! Simply send it a PWM signal from a 5V logic...

$9.95

47 IN STOCK

Adafruit 1.54" Tri-Color eInk / ePaper 200x200 Display with SRAM - SSD1681 Driver

PRODUCT ID: 4868

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances...

$19.95

IN STOCK

10.1" 1366x768 Display IPS + Speakers - HDMI/VGA/NTSC/PAL

PRODUCT ID: 2261

Yes, this is an adorable HDMI television with incredibly high resolution and built in 3.5W stereo speakers ! We tried to get the best possible...

Yes, this is an adorable HDMI television with incredibly high resolution and built in 3.5W stereo speakers ! We tried to get the best possible HDMI/VGA display with high-res, high-contrast visibility. The visible display measures 10.1" (25.7cm) diagonal, and the TFT comes in an enclosure with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect a 9 to 12VDC adapter to the 2.1mm center-positive DC jack (not...

$189.95

IN STOCK

NTSC/PAL (Television) TFT Display - 2.5" Diagonal

PRODUCT ID: 912

Yes, this is an adorable small television! The visible display measures only 2.5" (6.35cm) diagonal, the TFT comes with a NTSC/PAL driver board....

Yes, this is an adorable small television! The visible display measures only 2.5" (6.35cm) diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-12VDC to the red and black wires, then connect a composite video source to the yellow and black wire. Voila, a television display! There's one little button to adjust the LED backlight brightness up and down. There is no other...

$44.95

96 IN STOCK

Adjustable Bent-Wire Stand for 8-10 inch Tablets and Displays

Adjustable Bent-Wire Stand for 8-10" Tablets and Displays

PRODUCT ID: 1753

This handy bent-wire stand was originally designed to hold tablets from 8-10 inches but the rubberized design is great for general purpose...

This handy bent-wire stand was originally designed to hold tablets from 8-10 inches but the rubberized design is great for general purpose electronics & TFT holding. We use it to hold up our HDMI displays while connected to a Pi. You can adjust the angle and collapse it for travel. iPad, screen and Mho's Resistance not included :)

$4.95

43 IN STOCK

2.8" TFT Display with Resistive Touchscreen

PRODUCT ID: 1774

This is a screen for advanced hackers who like the look of the TFT screen we've put into the PiTFT, TFT shield v2 and 2.8" TFT breakout....

This is a screen for advanced hackers who like the look of the TFT screen we've put into the PiTFT, TFT shield v2 and 2.8" TFT breakout. This display has 320x240 pixels and is driven with the ILI9341 chipset. This is just the display module! No PCB is included! You can talk to this chip with SPI (4 or 3 wire), 8 bit parallel, or 16 bit parallel. It also can be put into "dot clock mode" for raw TTL signal in but we have never...

$17.95

IN STOCK

HDMI 4 Pi: 7" Display w/Touchscreen 1024x600 w/ Mini Driver

PRODUCT ID: 2396

Make a lovely, touchscreen video setup with a 7" screen at 1024x600 resolution with a resistive touchscreen overlay! For this...

Make a lovely, touchscreen video setup with a 7" screen at 1024x600 resolution with a resistive touchscreen overlay! For this model, we tried to get an inexpensive 1024x600 display that was still high quality and would be good for embedded computing usage. The visible display measures 7" diagonal. We matched this version with a small driver board that can be powered with a USB port. The driver board only has an...

$84.95

5 IN STOCK

Adafruit 2.13" 250x122 Tri-Color eInk / ePaper Display with SRAM - SSD1680 Driver

PRODUCT ID: 4947

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances...

$19.95

IN STOCK

Adafruit 2.7" Tri-Color eInk / ePaper Shield with SRAM - Red Black White

PRODUCT ID: 4229

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances...

$39.95

16 IN STOCK

Adafruit 2.9" Red/Black/White eInk Display Breakout - THINK INK

PRODUCT ID: 1028

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances...

$34.95

70 IN STOCK

HDMI 4 Pi: 5" Display w/Touch and Mini Driver - 800x480 HDMI

PRODUCT ID: 2109

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution and it has a resistive touchscreen overlay. And yes it comes with...

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution and it has a resistive touchscreen overlay. And yes it comes with an equally cute little driver board and USB-enabled 40-pin to 50-pin touchscreen adapter board. We tried to get the smallest display that would be good for embedded computing usage and at a good price. We also chose our favorite 5" touchscreen then paired it with a small USB powered driver...

$79.95

3 IN STOCK

HDMI 4 Pi: 7" Display & Audio 1024x600 w/Touchscreen

PRODUCT ID: 2397

"Give me the works!" That's what we said when we put together this 7" screen at 1024x600 resolution, with...

"Give me the works!" That's what we said when we put together this 7" screen at 1024x600 resolution, with a resistive touchscreen overlay AND with HDMI stereo speaker support ! For this model, we tried to get an inexpensive 1024x600 touchscreen display that was still high quality and would be good for embedded computing usage. The visible display measures 7" diagonal and is a 'raw TTL'...

$99.95

1 IN STOCK

HDMI 4 Pi - 7" Display 1280x800 (720p) IPS - HDMI/VGA/PAL/NTSC

PRODUCT ID: 1033

Yes, this is an adorable small HDMI television with incredibly high resolution! We tried to get the smallest possible HDMI/VGA display with high-res,...

Yes, this is an adorable small HDMI television with incredibly high resolution! We tried to get the smallest possible HDMI/VGA display with high-res, high-contrast visibility. The visible display measures only 7" (17.8cm) diagonal, and the TFT comes in an enclosure with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect the included 12VDC adapter to the 2.1mm center-positive DC jack, then connect a digital...

$159.95

12 IN STOCK

HDMI 4 Pi: 7" Display (no Touch) w/Mini Driver - 800x480 HDMI

PRODUCT ID: 1933

Yes, this is a 7" TFT display with WVGA 800x480 resolution and a cute little driver board. We tried to get the best medium-size display that...

Yes, this is a 7" TFT display with WVGA 800x480 resolution and a cute little driver board. We tried to get the best medium-size display that would be good for embedded computing usage and at a good price. And we also tried to match it with a small driver board that can be powered from a USB port. The visible display measures 7" diagonal and is a 'raw' TTL display as is used in portable electronics. The driver board only has an...

$69.95

41 IN STOCK

Adafruit TFT 50pin to 40pin with AR1100 Touchscreen Adapter

Adafruit TFT 50pin to 40pin + AR1100 Touchscreen Adapter

PRODUCT ID: 3305

This is a very special adapter, specifically used for adapting our RTD266X driver boards that have 50-pin TFT connectors to use 40-pin TFTs. Please...

This is a very special adapter, specifically used for adapting our RTD266X driver boards that have 50-pin TFT connectors to use 40-pin TFTs. Please note the adapter cannot be used the other way around! As an addition, we add in an AR1100 resistive touch controller. Resistive touch screens are incredibly popular as overlays to TFT and LCD displays. If you want to connect one to a computer you need something to handle the analog to digital...

$14.95

10 IN STOCK

3.2" TFT Display with Resistive Touchscreen

PRODUCT ID: 4278

This is a screen for advanced hackers who like the look of the TFT screen we've put into the PyPortal, PiTFT Plus, and TFT breakout. This display...

This is a screen for advanced hackers who like the look of the TFT screen we've put into the PyPortal, PiTFT Plus, and TFT breakout. This display has 320x240 pixels and is driven with the ILI9341 chipset. This is just the display module! No PCB is included! You can talk to this chip with SPI (4 or 3 wire), 8 bit parallel, or 16 bit parallel. It also can be put into "dot clock mode" for raw TTL signal in but we have never done this...

$29.95

97 IN STOCK

Monochrome OLED Graphic Display Module showing blue text

Monochrome 2.3" 128x32 OLED Graphic Display Module Kit

PRODUCT ID: 2675

If you've been diggin' our monochome OLEDs but need something bigger, this display will delight you. These displays are 2.3" diagonal,...

If you've been diggin' our monochome OLEDs but need something bigger, this display will delight you. These displays are 2.3" diagonal, and very readable due to the high contrast of an OLED display. This display is made of 128x32 individual blue OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why...

$39.95

83 IN STOCK

Adafruit Qualia 9.7 inch DisplayPort Monitor on table showing an image of LED puppets

Adafruit Qualia 9.7" DisplayPort Monitor - 2048x1536 Resolution

PRODUCT ID: 1652

Add a glorious 2048x1536 retina-blasting, ultra-high pixel density, IPS display to any computer with a Thunderbolt/DisplayPort port. This product...

Add a glorious 2048x1536 retina-blasting, ultra-high pixel density, IPS display to any computer with a Thunderbolt/DisplayPort port. This product comes with a new 9.7" diagonal TFT display module (the same one used in the iPad 3 & 4), along with our custom made driver board, a stand-up monitor enclosure kit, 10' DisplayPort cable and 9V power adapter. The driver board is a work of art (it was designed by resident engineer KTOWN) -...

$224.95

7 IN STOCK

7.0" 40-pin TFT Display - 800x480 with Touchscreen

PRODUCT ID: 2354

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need...

This 7.0" TFT screen has lots of pixels, 800x480 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer electronics, such as miniature TV's, GPS's, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability. This version has a 4-wire...

NOTIFY ME

$47.50

OUT OF STOCK

NOTIFY ME

USB + Serial Backpack Kit with 16x2 RGB backlight positive LCD - Black on RGB

PRODUCT ID: 782

Adding a character display to your project or computer has never been easier with the new Adafruit USB or TTL serial backpack! This custom-designed...

NOTIFY ME

$24.95

OUT OF STOCK

NOTIFY ME

4.3" 40-pin TFT Display - 480x272 with Touchscreen

PRODUCT ID: 1591

This 4.3" TFT screen has lots of pixels, 480x272 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need...

This 4.3" TFT screen has lots of pixels, 480x272 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer electronics, such as miniature TV's, GPS's, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability. This is a "raw...

NOTIFY ME

$29.95

OUT OF STOCK

NOTIFY ME

Keyboard FeatherWing - QWERTY Keyboard + 2.6" LCD

PRODUCT ID: 4818

From the folks at Solder Party comes the Keyboard FeatherWing , an easy way to add a handheld QWERTY keyboard and a...

From the folks at Solder Party comes the Keyboard FeatherWing , an easy way to add a handheld QWERTY keyboard and a 2.6” color display (+ more) to your project! Nice hand-held size and great for typing with your thumbs, early 2000s-style. The keyboard itself does not contain an MCU/CPU/SoC that you can program; you will need a board compatible with the Adafruit Feather Ecosystem. Once you plug it into the...

NOTIFY ME

$67.50

OUT OF STOCK

NOTIFY ME

Adafruit Mini Color TFT with Joystick FeatherWing

PRODUCT ID: 3321

Add a dazzling color display to your Feather project with this Adafruit Mini Color TFT with Joystick FeatherWing . It has so much stuff going...

Add a dazzling color display to your Feather project with this Adafruit Mini Color TFT with Joystick FeatherWing . It has so much stuff going on, we could not fit any more parts on the PCB! There's a 0.96" 160x80 Color TFT Display with 16-bit full color capability. And, so you can make a proper UI we added a 5-way navigation switch and two push buttons. The joystick can go left, right, up, down and 'in' for selection. Two...

NOTIFY ME

$24.95

OUT OF STOCK

NOTIFY ME

RGB backlight positive LCD 16x2 + extras - black on RGB

PRODUCT ID: 398

This is a fancy upgrade to standard 16x2 LCDs, instead of just having blue and white, or red and black, this LCD has black characters on a full color...

This is a fancy upgrade to standard 16x2 LCDs, instead of just having blue and white, or red and black, this LCD has black characters on a full color RGB-backlight background! That means you can change the background color to anything you want - red, green, blue, pink, white, purple yellow, teal, salmon, chartreuse, or just leave it off for a neutral background. This LCD is the most daylight readable character LCD we have and is very beautiful...

NOTIFY ME

$12.95

OUT OF STOCK

NOTIFY ME

1.8" Color TFT LCD display with MicroSD Card Breakout - ST7735R

PRODUCT ID: 358

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to...

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.8" display has 128x160 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are...

NOTIFY ME

$19.95

OUT OF STOCK

NOTIFY ME

Adafruit HalloWing M4 Express - ORANGE HALLOWEEN EDITION!

PRODUCT ID: 4300

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we...

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we UPPED our -skull-shaped development board game, and re-spinned (re-spun?) the HalloWing M0 into the HalloWing M4 with MORE of everything that makes this the spoooookiest dev board. New! For October 2019, we're got limited edition halloween-orange HallowingM4's - Same exact electronics and...

NOTIFY ME

$39.95

OUT OF STOCK

NOTIFY ME

TFP401 HDMI/DVI Decoder to 40-Pin TTL Breakout - Without Touch

PRODUCT ID: 2218

It's a mini HDMI decoder board! So small and simple, you can use this board as an all-in-one display driver for TTL displays, or perhaps decoding...

NOTIFY ME

$24.95

OUT OF STOCK

NOTIFY ME

Large Liquid Crystal Light Valve - Controllable Shutter Glass

PRODUCT ID: 3330

What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a...

NOTIFY ME

$7.50

OUT OF STOCK

NOTIFY ME

DIY HDMI Cable Parts - Straight Mini HDMI Socket Adapter

PRODUCT ID: 3555

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Mini HDMI socket . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to craft your...

NOTIFY ME

$6.50

OUT OF STOCK

NOTIFY ME

TFT FeatherWing - 2.4" 320x240 Touchscreen For All Feathers

PRODUCT ID: 3315

A Feather board without ambition is a Feather board without FeatherWings! Spice up your Feather project with a beautiful 2.4" touchscreen...

A Feather board without ambition is a Feather board without FeatherWings! Spice up your Feather project with a beautiful 2.4" touchscreen display shield with built in microSD card socket. This TFT display is 2.4" diagonal with a bright 4 white-LED backlight. You get 240x320 pixels with individual 16-bit color pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display comes with a...

NOTIFY ME

$34.95

OUT OF STOCK

NOTIFY ME

DIY HDMI Cable Parts - Right Angle (L Bend) HDMI Plug Adapter

PRODUCT ID: 3550

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (left bend) HDMI plug . Ribbon cable and other adapter not included! Check out all of the options we have in the shop to...

NOTIFY ME

$6.50

OUT OF STOCK

NOTIFY ME

5.0" 40-pin 800x480 TFT Display without Touchscreen

PRODUCT ID: 1680

This 5.0" TFT screen has lots of pixels, 800x480 to be exact, and an LED backlight. Its great for when you need a lot of space for graphics....

This 5.0" TFT screen has lots of pixels, 800x480 to be exact, and an LED backlight. Its great for when you need a lot of space for graphics. These screens are commonly seen in consumer electronics, such as miniature TV's, GPS's, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability. This version does not have touchscreen attached It's exactly the same TFT...

NOTIFY ME

$29.95

OUT OF STOCK

NOTIFY ME

7" Display 1280x800 (720p) IPS + Speakers - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1667

Yes, this is an adorable small HDMI television with incredibly high resolution and built in 3W stereo speakers ! We tried to get the smallest...

Yes, this is an adorable small HDMI television with incredibly high resolution and built in 3W stereo speakers ! We tried to get the smallest possible HDMI/VGA display with high-res, high-contrast visibility. The visible display measures only 7" (17.8cm) diagonal, and the TFT comes in an enclosure with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect a 9 to 12VDC adapter to the 2.1mm center-positive DC jack (not...

NOTIFY ME

$169.95

OUT OF STOCK

NOTIFY ME

NTSC/PAL (Television) TFT Display - 3.5" Diagonal

PRODUCT ID: 913

Yes, this is an adorable small television! The visible display measures only 3.5" (8.9cm) diagonal, the TFT comes with a NTSC/PAL driver board....

Yes, this is an adorable small television! The visible display measures only 3.5" (8.9cm) diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-12VDC to the red (+) and black (-) wires, then connect a composite video source to the RCA connectors. Voila, a television display! There's three little buttons that let you enter a menu system for adjusting brightness, color and contrast. The...

NOTIFY ME

$44.95

OUT OF STOCK

NOTIFY ME

RGB backlight positive LCD 20x4 + extras - black on RGB

PRODUCT ID: 499

This is a fancy upgrade to standard 20x4 LCDs, instead of just having blue and white, or red and black, this LCD has black characters on a full color...

This is a fancy upgrade to standard 20x4 LCDs, instead of just having blue and white, or red and black, this LCD has black characters on a full color RGB background! That means you can change the display background color to anything you want - red, green, blue, pink, white, purple yellow, teal, salmon, chartreuse. This LCD looks strikingly good in person. This LCD is the most daylight readable character LCD we have and is very beautiful and easy...

NOTIFY ME

$24.95

OUT OF STOCK

NOTIFY ME

10.1" Display & Audio 1280x800 IPS - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1694

Make a lovely audio/video setup with a 10.1" IPS screen with HDMI stereo speaker support. For video, we have a beautiful bright 10.1" TFT...

Make a lovely audio/video setup with a 10.1" IPS screen with HDMI stereo speaker support. For video, we have a beautiful bright 10.1" TFT display with incredibly high resolution and great angle-visibility! We tried to get the thinnest, brightest, highest resolution display that would be good for embedded computing usage. The visible display measures 10" diagonal and is a 'raw' display as is used in a tablet, ultra thin...

NOTIFY ME

$174.95

OUT OF STOCK

NOTIFY ME

pyboard Color LCD Skin with Resistive Touch - LCD160CR v1.1

PRODUCT ID: 3498

The color LCD skin is a module that fits right onto the pyboard. It provides a 160x128 pixel, 16-bit graphical LCD display with backlight, as well as...

The color LCD skin is a module that fits right onto the pyboard. It provides a 160x128 pixel, 16-bit graphical LCD display with backlight, as well as a resistive touch sensor covering the entire screen. The screen has 160x128 pixels of 16-bit color, has a backlight with a software-controllable intensity, and a resistive touch sensor which can detect a single force-based touch anywhere on the screen. The display has a custom controller which...

NOTIFY ME

$39.95

OUT OF STOCK

NOTIFY ME

HDMI 4 Pi: 5" Display (no Touch) w/Mini Driver - 800x480 HDMI

PRODUCT ID: 1928

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution and a cute little driver board. We tried to get the smallest display that...

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution and a cute little driver board. We tried to get the smallest display that would be good for embedded computing usage and at a good price. And we also tried to match it with a small driver board that can be powered from a USB port. The visible display measures 5" diagonal and is a 'raw' TTL display as is used in portable electronics. The driver board only has...

NOTIFY ME

$59.95

OUT OF STOCK

NOTIFY ME

HDMI 4 Pi: 7" Display no Touchscreen 1024x600- HDMI/VGA/NTSC/PAL

PRODUCT ID: 2299

Make a lovely video setup with a 7" screen at 1024x600 resolution . For this model, we tried to get an inexpensive 1024x600 display that was...

Make a lovely video setup with a 7" screen at 1024x600 resolution . For this model, we tried to get an inexpensive 1024x600 display that was still high quality and would be good for embedded computing usage. The visible display measures 7" diagonal and is a 'raw TTL' display. We include a driver board with HDMI, VGA and Composite inputs. The setup is very easy to use - simply connect a 5-12VDC adapter to the 2.1mm...

NOTIFY ME

$74.95

OUT OF STOCK

NOTIFY ME

HDMI 4 Pi: 7" Display w/Touchscreen 1024x600- HDMI/VGA/NTSC/PAL

PRODUCT ID: 2395

Make a lovely, touchscreen video setup with a 7" screen at 1024x600 resolution with a resistive touchscreen overlay ! For this...

Make a lovely, touchscreen video setup with a 7" screen at 1024x600 resolution with a resistive touchscreen overlay ! For this model, we tried to get an inexpensive 1024x600 touchscreen display that was still high quality and would be good for embedded computing usage. The visible display measures 7" diagonal. We include a driver board with HDMI, VGA and Composite inputs. We also include one of our...

NOTIFY ME

$89.95

OUT OF STOCK

NOTIFY ME

HDMI 4 Pi 5" Display not Touchscreen 800x480 - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1678

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution ( NOT TOUCHSCREEN ). We tried to get the smallest display that would be...

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution ( NOT TOUCHSCREEN ). We tried to get the smallest display that would be good for embedded computing usage and at a good price. The visible display measures 5" diagonal and is a 'raw' TTL display as is used in portable electronics. We include a driver board with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect a 5-12V DC...

NOTIFY ME

$64.95

OUT OF STOCK

NOTIFY ME

HDMI 4 Pi: 7" Display & Audio 1024x600 - HDMI/VGA/NTSC/PAL

PRODUCT ID: 2301

Yes, this is a 7" TFT display with 1024x600 resolution with audio-over-HDMI capability! We tried to get the best medium-size display that...

Yes, this is a 7" TFT display with 1024x600 resolution with audio-over-HDMI capability! We tried to get the best medium-size display that would be good for embedded computing usage and at a good price. We include a driver board with HDMI, VGA and Composite inputs as stereo 4 ohm at 3W output speaker driving capability. The visible display measures 7" diagonal and is a 'raw TTL' display. The set up is very easy to use...

NOTIFY ME

$84.95

OUT OF STOCK

NOTIFY ME

Nokia 5110/3310 monochrome LCD + extras

PRODUCT ID: 338

These displays were used in old Nokia 5110/3310 cell phones (before the smart-phone fad turned every cell phone into a TV). It's a 84x48...

These displays were used in old Nokia 5110/3310 cell phones (before the smart-phone fad turned every cell phone into a TV). It's a 84x48 pixel monochrome LCD display. These displays are small, only about 1.5" diagonal, but very readable and come with a white backlight. This display is made of 84x48 individual pixels, so you can use it for graphics, text or bitmaps. These displays are inexpensive, easy to use, require only a few...

NOTIFY ME

$10.00

OUT OF STOCK

NOTIFY ME

HDMI 4 Pi: 7" Display no Touchscreen 1024x600 w/ Mini Driver

PRODUCT ID: 2300

Yes, this is a 7" TFT display with 1024x600 resolution and a cute little driver board. We tried to get the best medium-size display that...

Yes, this is a 7" TFT display with 1024x600 resolution and a cute little driver board. We tried to get the best medium-size display that would be good for embedded computing usage and at a good price. And we also tried to match it with a small driver board that can be powered from a USB port. The visible display measures 7" diagonal and is a 'raw' TTL display as is used in portable electronics. The driver board only has an...

NOTIFY ME

$69.95

OUT OF STOCK

NOTIFY ME

TFT breakout wired up on breadboard, showing colorful image

Adafruit 0.96" 160x80 Color TFT Display w/ MicroSD Card Breakout - ST7735

PRODUCT ID: 3533

Say hello to our 0.96" 160x80 Color TFT Display w/ MicroSD Card Breakout – we think it's T - F - T errific! It's the size of your...

Say hello to our 0.96" 160x80 Color TFT Display w/ MicroSD Card Breakout – we think it's T - F - T errific! It's the size of your thumbnail, with glorious 160x80 pixel color. This very very small display is only 0.96" diagonal, packed with RGB pixels, for making very small high-density displays. This lovely little display breakout is a great way to add a small, colorful and bright display to any project. Since the display...

NOTIFY ME

$14.95

OUT OF STOCK

NOTIFY ME

Adafruit 1.5" Red/Black/White eInk Display Breakout

Adafruit 1.54" 152x152 Tri-Color eInk / ePaper Display with SRAM - 152x152 with IL0373

PRODUCT ID: 3625

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances...

$22.50

48 IN STOCK

Pimoroni Inky wHAT (ePaper/eInk/EPD) - Black/White

PRODUCT ID: 4142

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic...

MORE INFO

DISCONTINUED

MORE INFO

Mini enclosed TFT Television wired up to Raspberry Pi, showing off desktop screen.

NTSC/PAL (Television) TFT Display - 4.3" Diagonal

PRODUCT ID: 946

Yes, this is an adorable small television! The visible display measures only 4.3" (11cm) diagonal, the TFT comes with a NTSC/PAL driver board,...

Yes, this is an adorable small television! The visible display measures only 4.3" (11cm) diagonal, the TFT comes with a NTSC/PAL driver board, enclosure and stand. The display is very easy to use - simply connect 12VDC to the 2.1mm center-positive DC jack (or use the cable and connect to the red and black wires), then connect a composite video source to one of the RCA cable. Voila, a television display! There's three little buttons in...

MORE INFO

DISCONTINUED

MORE INFO

Enclosed TFT Television wired up to Raspberry Pi, showing off desktop screen.

NTSC/PAL (Television) TFT Display - 7" Diagonal

PRODUCT ID: 947

Yes, this is an adorable small television! The visible display measures only 7" (17.8cm) diagonal, the TFT comes with a NTSC/PAL driver board,...

Yes, this is an adorable small television! The visible display measures only 7" (17.8cm) diagonal, the TFT comes with a NTSC/PAL driver board, enclosure and stand. The display is very easy to use - simply connect the included 12VDC adapter to the 2.1mm center-positive DC jack, then connect a composite video source to one of the RCA cable. Voila, a television display! There's some little buttons on the front that let you enter a menu...

MORE INFO

DISCONTINUED

MORE INFO

HDMI 4 Pi: 7" Display 1280x800 IPS - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1931

Make a lovely video setup with a 7" IPS screen at 1280x800. Here we have a beautiful bright 7" TFT display with incredibly high resolution...

Make a lovely video setup with a 7" IPS screen at 1280x800. Here we have a beautiful bright 7" TFT display with incredibly high resolution and great angle-visibility! We tried to get the thinnest, brightest, highest resolution display that would be good for embedded computing usage. The visible display measures 7" diagonal and is a 'raw LVDS' display as is used in a tablet which makes it ultra thin and very bright. We...

MORE INFO

DISCONTINUED

MORE INFO

NTSC/PAL (Television) Video Glasses

PRODUCT ID: 1452

You are from the future with these futuristic video glasses. Or at least, an 80's version of the future. Wearing these turns your vision into what...

You are from the future with these futuristic video glasses. Or at least, an 80's version of the future. Wearing these turns your vision into what appears to be a 52" television a few feet away. These are basic video glasses, they do work well, taking standard NTSC/PAL video in and projecting a 320x240 display onto your eyeballs. They're not terribly comfortable for long term use as they're a bit heavy, but we think these would be best used for...

MORE INFO

DISCONTINUED

MORE INFO

SHARP Memory Display Breakout next to quarter

SHARP Memory Display Breakout - 1.3" 96x96 Silver Monochrome

PRODUCT ID: 1393

The 96x96 resolution SHARP Memory LCD is no longer made, but we have a higher-resolution 168x144 display available in the shop at...

The 96x96 resolution SHARP Memory LCD is no longer made, but we have a higher-resolution 168x144 display available in the shop at https://www.adafruit.com/product/3502 The 1.3" SHARP Memory LCD display is a cross between an eInk (e-paper) display and an LCD. It has the ultra-low power usage of eInk and the fast-refresh rates of an LCD. This model has a matt silver background, and pixels show up as little mirrors for a silver-reflective...

MORE INFO

DISCONTINUED

MORE INFO

Graphic ST7565 Positive LCD (128x64) with RGB backlight + extras - ST7565

PRODUCT ID: 250

This graphical display looks great, costs less! The dark gray pixels are visible in daylight, and there's also a full RGB LED backlight, which...

This graphical display looks great, costs less! The dark gray pixels are visible in daylight, and there's also a full RGB LED backlight, which you can control with PWM to make any color you can imagine. Four mounting holes and a blank 11 pin 2mm-pitch labeled breakout on the side - we just soldered some wire to each hole as shown in the photos, its very easy. (The LCDs have no wires soldered in when we ship them) Bonus! We're including a...

MORE INFO

DISCONTINUED

MORE INFO

Graphic ST7565 Negative LCD (128x64) with RGB backlight + extras - ST7565

PRODUCT ID: 438

This graphical display looks fantastic, at a great price! This display will add the ultimate cool to your project, with a black negative display that...

This graphical display looks fantastic, at a great price! This display will add the ultimate cool to your project, with a black negative display that has a full RGB LED backlight. You can control with PWM to make any color you can imagine, and it will look stunning with the black inverted (negative) background. Four mounting holes and a blank 11 pin 2mm-pitch labeled breakout on the side - we just soldered some wire to each hole as shown in the...

MORE INFO

DISCONTINUED

MORE INFO

RePaper - 2.7" Graphic eInk Development Board - SM027

PRODUCT ID: 1346

Ever since the Kindle eReader came out, we've been wanting a nice small graphical eInk display that is easy to use with a microcontroller. And...

Ever since the Kindle eReader came out, we've been wanting a nice small graphical eInk display that is easy to use with a microcontroller. And finally our desires have been fulfilled with the rePaper 2.7" development board from Pervasive Displays! We're excited to offer this very interesting display breakout for hackers who want to start playing with small eInk displays. This kit comes with a driver board that is powered from 3V and...

MORE INFO

DISCONTINUED

MORE INFO

RePaper - 2.0" Graphic eInk Development Board - SG020

PRODUCT ID: 1316

Ever since the Kindle eReader came out, we've been wanting a nice small graphical eInk display that is easy to use with a microcontroller. And...

Ever since the Kindle eReader came out, we've been wanting a nice small graphical eInk display that is easy to use with a microcontroller. And finally our desires have been fulfilled with the rePaper 2.0" development board from Pervasive Displays! We're excited to offer this very interesting display breakout for hackers who want to start playing with small eInk displays. This kit comes with a driver board that is powered from 3V and...

MORE INFO

DISCONTINUED

MORE INFO

Analog panel meter with range of 0 to 50 uA

Analog panel meter - 50uA

PRODUCT ID: 252

Analog panel meters are not as blingy as LEDs but they add a touch of elegance and are easier to read quickly. This one is fairly large and is easy...

Analog panel meters are not as blingy as LEDs but they add a touch of elegance and are easier to read quickly. This one is fairly large and is easy to open up the front with two screws and replace the gauge. There's a 'zero adjust' as well. The back has four 3mm (4-40) screws, 6.5cm apart, so its easy to attach to a box or enclosure Size: 3.125" (8 cm) square, 1.25" thick (the panel is 0.5", the coil sticks out another...

MORE INFO

DISCONTINUED

MORE INFO

RePaper - 1.44" Graphic eInk Development Board - SG020

PRODUCT ID: 1347

Ever since the Kindle eReader came out, we've been wanting a nice small graphical eInk display that is easy to use with a microcontroller. And...

Ever since the Kindle eReader came out, we've been wanting a nice small graphical eInk display that is easy to use with a microcontroller. And finally our desires have been fulfilled with the rePaper 1.44" development board from Pervasive Displays! We're excited to offer this very interesting display breakout for hackers who want to start playing with small eInk displays. This kit comes with a driver board that is powered from 3V...

MORE INFO

DISCONTINUED

MORE INFO

RCA coupler - Male to Male

PRODUCT ID: 951

This coupler is kind of like a really short RCA cable. We think its perfect for use with our NTSC/PAL displays since they already have a cable. So...

This coupler is kind of like a really short RCA cable. We think its perfect for use with our NTSC/PAL displays since they already have a cable. So instead of a long cable from the display to something like the Raspberry Pi, just pop one of these in between!

MORE INFO

DISCONTINUED

MORE INFO

20x2 Character Vacuum Fluorescent Display lit up with text "20x2 char. SPI VFD. Adafruit heart Arduino"

20x2 Character VFD (Vacuum Fluorescent Display) - SPI interface - 20T202DA2JA

PRODUCT ID: 347

One up your plain old character LCD with a gorgeous VFD! These displays look and act just like character LCDs but are way glowier, and are very...

One up your plain old character LCD with a gorgeous VFD! These displays look and act just like character LCDs but are way glowier, and are very readable even from a distance. As a bonus, you only need 3 digital pins to control it as it is a SPI/serial interface not parallel. We have a datasheet for the module and the datasheet for the controller chip (with much more detail in case you need it) These are often used at point of sale machines (at...

MORE INFO

DISCONTINUED

MORE INFO

2.8" TFT Touch Shield for Arduino - 2.8"

PRODUCT ID: 376

We've discontinued this version of the shield (which was expensive and difficult to make) and replaced it with a version 2: its got a better...

We've discontinued this version of the shield (which was expensive and difficult to make) and replaced it with a version 2: its got a better price, uses way fewer pins, is Mega/Leonardo compatible and has a great touchscreen controller built in. Wow! Check it out here. Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.8" diagonal) bright (4...

MORE INFO

DISCONTINUED

MORE INFO

Pixel Qi 10" Display with Controller- 1024x600 HDMI/VGA/NTSC/PAL

PRODUCT ID: 1303

We're really excited to offer the revolutionary Pixel Qi display, a full color screen that can also be used in daylight. The Qi has three modes -...

We're really excited to offer the revolutionary Pixel Qi display, a full color screen that can also be used in daylight. The Qi has three modes - backlit color, backlit grayscale and daylight grayscale. In normal office/indoor use you'll want to go with keeping the backlight on to reveal the color layer. The screen works just like any other 10" TFT with fast refresh (not like slow e-ink). When a bright light shines on it, the...

MORE INFO

DISCONTINUED

MORE INFO

HDMI 4 Pi - 5.6" Display 1280x800 (720p) Kit - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1666

Yes, this is a super-sharp 5.6" TFT display with incredibly high resolution - it has 270 PPI! We tried to get the smallest & highest...

Yes, this is a super-sharp 5.6" TFT display with incredibly high resolution - it has 270 PPI! We tried to get the smallest & highest resolution display that would be good for embedded computing usage. The visible display measures 5.6" diagonal and is a 'raw' LVDS display as is used in a tablet, ultra thin with some mounting tabs around the edge. We include a driver board with HDMI, VGA and Composite inputs. The display is...

MORE INFO

DISCONTINUED

MORE INFO

5.6" Display & Audio 1280x800 (720p) Kit - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1695

Make a lovely audio/video setup with a 5.6" 720p screen with HDMI stereo speaker support. For video, we have a super-sharp 5.6" TFT display...

Make a lovely audio/video setup with a 5.6" 720p screen with HDMI stereo speaker support. For video, we have a super-sharp 5.6" TFT display with incredibly high resolution - it has 270 PPI! We tried to get the smallest & highest resolution display that would be good for embedded computing usage. The visible display measures 5.6" diagonal and is a 'raw' LVDS display as is used in a tablet, ultra thin with some mounting...

MORE INFO

DISCONTINUED

MORE INFO

Monochrome 128x32 I2C OLED graphic display

PRODUCT ID: 931

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32...

MORE INFO

DISCONTINUED

MORE INFO

PaPiRus 2.7" eInk Display HAT for Raspberry Pi from Pi Supply

PRODUCT ID: 3420

The PaPiRus Screen HAT from Pi Supply is an ePaper / eInk screen HAT designed for the Raspberry Pi. Think of it as the older sibling of the...

The PaPiRus Screen HAT from Pi Supply is an ePaper / eInk screen HAT designed for the Raspberry Pi. Think of it as the older sibling of the PaPiRus Zero. ePaper / eInk is a display technology that mimics the appearance of ink on normal paper. Unlike conventional displays, ePaper reflects light – just like ordinary paper – and is capable of holding text and images indefinitely, even without electricity. Because of this, ePaper...

MORE INFO

DISCONTINUED

MORE INFO

Circuit Playground 152x152 Tri-Color E-Ink Gizmo - E-Ink Display + Audio Amplifier

PRODUCT ID: 4428

Discontinued - you can grab Circuit Playground 200x200 Tri-Color E-Ink Gizmo instead! Extend and expand your Circuit Playground projects...

Discontinued - you can grab Circuit Playground 200x200 Tri-Color E-Ink Gizmo instead! Extend and expand your Circuit Playground projects with a bolt on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and reliable fashion. This PCB looks just like a round E-Ink breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Chances are you've seen one of those...

MORE INFO

DISCONTINUED

MORE INFO

2.2" 18-bit color TFT LCD display with microSD card breakout - HX8340BN

PRODUCT ID: 797

This TFT was discontinued! We have another 2.2" TFT in the shop, so check that out if you need a 2.2" display for your project. Please note...

This TFT was discontinued! We have another 2.2" TFT in the shop, so check that out if you need a 2.2" display for your project. Please note it does not use the same wiring or controller so it is not a drop-in replacement for this TFT. This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 3-wire SPI to communicate and has its own pixel-addressable frame...

MORE INFO

DISCONTINUED

MORE INFO

Front of large graphical LCD with loose header and potentiometer

Graphic KS0108 LCD 128x64 + extras - white on blue

PRODUCT ID: 188

A big, bold, beautiful blue LCD with white back-lit pixels. This LCD is the graphical upgrade to those popular 16x2 LCDs, but allows full graphical...

A big, bold, beautiful blue LCD with white back-lit pixels. This LCD is the graphical upgrade to those popular 16x2 LCDs, but allows full graphical control. Blue background with 128 x 64 'monochrome' white pixelsLow power white LED back-lightThe LCD is driven by on-board 5V parallel interface chipset KS0108 and KS0107. They are extremely common and well documentedExisting Arduino library over at the wiki use 'pin out B'PCB is...

MORE INFO

DISCONTINUED

MORE INFO

32x32 RGB LED Matrix showing a planetoid graphic

PIXEL Guts Kit - Bluetooth Controlled 32x32 RGB LED Matrix Kit - V2.5

PRODUCT ID: 1357

Control a 32x32 LED matrix with your Android, PC, Mac, Linux, Raspberry Pi, or BeagleBone Black with the Pixel Guts Kit V2.5 ! Simply use...

Control a 32x32 LED matrix with your Android, PC, Mac, Linux, Raspberry Pi, or BeagleBone Black with the Pixel Guts Kit V2.5 ! Simply use PIXEL’s free apps and send images, GIF animations, scrolling text, Twitter feeds, and your own pixel art creations in minutes, no soldering or coding required! As an added bonus, the 180+ works of original pixel art commissioned for the Kickstarter project comes included too. PIXEL has two modes:...

MORE INFO

DISCONTINUED

MORE INFO

Adafruit 2.1" Red/Black/White eInk Display Breakout

Adafruit 2.13" Tri-Color eInk / ePaper Display with SRAM - Red Black White

PRODUCT ID: 4086

Discontinued - you can grab Adafruit 2.13" 250x122 Tri-Color eInk / ePaper Display with SRAM - SSD1680 Driver instead! Easy...

Discontinued - you can grab Adafruit 2.13" 250x122 Tri-Color eInk / ePaper Display with SRAM - SSD1680 Driver instead! Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that...

MORE INFO

DISCONTINUED

MORE INFO

Wired up 16x2 OLED with blue on black text "Hello World! Adafruit <3 OLED"

Blue Character OLED 16x2

PRODUCT ID: 823

When you need low power, ultra-high contrast and any-angle readability, you can't beat these great looking character OLEDs. They are pin/shape...

When you need low power, ultra-high contrast and any-angle readability, you can't beat these great looking character OLEDs. They are pin/shape compatible with 'standard' HD44780 LCDs. The code is slightly different (they're more timing sensitive) so we have our own Arduino library that plays better with the OLEDs than the standard LiquidCrystal library. Best of all, no backlight or contrast control is required, so they're...

MORE INFO

DISCONTINUED

MORE INFO

Front of large graphical LCD with black screen

MONOCHRON KS0108 Graphic LCD - white on black

PRODUCT ID: 253

A big, bold, beautiful, black LCD with white back-lit pixels. This LCD is the graphical upgrade to those popular 16x2 LCDs, but allows full graphical...

A big, bold, beautiful, black LCD with white back-lit pixels. This LCD is the graphical upgrade to those popular 16x2 LCDs, but allows full graphical control. This LCD is used in the MONOCHRON kit, we had to custom order these to get the black color so they are more expensive than the more common blue & white ones. Black background with 128 x 64 'monochrome' white pixelsLow power white LED back-lightThe LCD is driven by on-board 5V...

MORE INFO

DISCONTINUED

MORE INFO

HDMI 4 Pi: 7" Display & Audio 1280x800 IPS - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1726

Make a lovely audio/video setup with a 7" IPS screen with HDMI stereo speaker support. For video, we have a beautiful bright 7" TFT display...

Make a lovely audio/video setup with a 7" IPS screen with HDMI stereo speaker support. For video, we have a beautiful bright 7" TFT display with incredibly high resolution and great angle-visibility! We tried to get the thinnest, brightest, highest resolution display that would be good for embedded computing usage. The visible display measures 7" diagonal and is a 'raw LVDS' display as is used in a tablet which makes it...

MORE INFO

DISCONTINUED

MORE INFO

Adafruit 2.13" Tri-Color eInk / ePaper Display FeatherWing - 212 x 104 pixels - Z16 Panel wit

PRODUCT ID: 4128

Easy e-paper finally comes to your Feather, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are...

Easy e-paper finally comes to your Feather, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The image is also high contrast and very daylight readable. It...

MORE INFO

DISCONTINUED

MORE INFO

Hand touching 4.3 inch LCD Capacitive Touchscreen Display Cape for BeagleBone

4.3" LCD Capacitive Touchscreen Display Cape for BeagleBone

PRODUCT ID: 3396

Add a 4.3” TFT LCD Display with capacitive touch to your BeagleBone! The Element 14 LCD Display Cape offers a high...

Add a 4.3” TFT LCD Display with capacitive touch to your BeagleBone! The Element 14 LCD Display Cape offers a high luminance, cap-touch panel display function. This 4.3” Touchscreen Display Cape connects directly to your BeagleBone (White, Black, or Wireless) to provide a full color touchscreen display solution. The display features a vivid 4.3” LED backlit 480 x 272 TFT LCD with capacitive overlay for...

MORE INFO

DISCONTINUED

MORE INFO

Hand holding TFT screen with finger swiping between two photos

Microtouch - AVR development board with 2.8" TFT Touch Screen

PRODUCT ID: 330

We've not made the Microtouch for many years - check out the PyPortal for a similar device that also includes WiFi and a Cortex M4 processor!...

We've not made the Microtouch for many years - check out the PyPortal for a similar device that also includes WiFi and a Cortex M4 processor! Sure, the latest "iTouchy" gadgets are pretty cool. But who wants a locked down device? Why not build your own touch-screen device , with your own apps, all on open source hardware and using open source tools? OK, it can't play MP3s, but it does have a 320x240 TFT color display with...

MORE INFO

DISCONTINUED

MORE INFO

HDMI 4 Pi: 5" Display (w/Touch) 800x480 - HDMI/VGA/NTSC/PAL

PRODUCT ID: 2110

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution and it has a resistive touchscreen overlay . This display comes...

Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution and it has a resistive touchscreen overlay . This display comes with a driver board with HDMI, VGA, and Composite inputs and USB-enabled 40-pin to 50-pin touchscreen adapter board. We tried to get the smallest display that would be good for embedded computing usage and at a good price. We also chose our favorite 5" touchscreen then paired it with a...

MORE INFO

DISCONTINUED

MORE INFO

2.8 1color TFT LCD with touchscreen breakout board showing colorful lines

2.8" 18-bit color TFT LCD with touchscreen breakout board - ILI9325

PRODUCT ID: 335

This screen has been discontinued, but we have a nearly identical replacement, the 2.8" ILI341 touchscreen breakout which as both 8-bit and SPI...

This screen has been discontinued, but we have a nearly identical replacement, the 2.8" ILI341 touchscreen breakout which as both 8-bit and SPI interface modes as well as a MicroSD card socket all in the same form factor so check it out! Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320...

MORE INFO

DISCONTINUED

MORE INFO

Monochrome 1.54" 128x64 OLED Graphic Display Module Kit

PRODUCT ID: 2720

Discontinued - you can grab Monochrome 1.3" 128x64 OLED graphic display - STEMMA QT / Qwiic instead! If you've been diggin'...

Discontinued - you can grab Monochrome 1.3" 128x64 OLED graphic display - STEMMA QT / Qwiic instead! If you've been diggin' our monochrome OLEDs but need something bigger, this display will delight you! These displays are 1.54" diagonal , and very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one turned on or off by the...

MORE INFO

DISCONTINUED

MORE INFO

128x64 Graphic VFD (Vacuum Fluorescent Display) - SPI interface

PRODUCT ID: 773

For blue-glow lovers, this is a graphical VFD with 128x64 bit resolution and a stunning high-brightness/high-contrast look. This module would be a...

For blue-glow lovers, this is a graphical VFD with 128x64 bit resolution and a stunning high-brightness/high-contrast look. This module would be a great addition to any project where readability is a must - you can read it in daylight, and at any angle. The VFD module supports both 8-bit parallel and SPI modes of communication. The SPI protocol allows to write and read pixels so no RAM is required to buffer the display (most 128x64 SPI displays...

MORE INFO

DISCONTINUED

MORE INFO