Cables / USB Cables / USB Micro B

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box. The jack half has two mounting 'ears' with M3 screws installed, ~1.1" / ~29mm apart. Can be used with box walls 0.125" to 0.25" wide. Depending on your usage you may...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long

This panel mount cable will allow you to enclose a device that has a USB Micro B port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Micro B plug connector, and other is a USB C socket with special over-molding. The socket side has two mounting 'ears' with M3 screws installed 20mm...

Check out this handy MicroUSB extension cable, which will make it easy for you to enclose a device that has a B type (micro USB host) port. Great if you need to extend the USB port for your Raspberry Pi, Arduino, Feather or really anything development board. This Micro-B male/female extension cable features a male USB Micro-B plug on one end, and a bulkhead mountable...

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to Micro B plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any computer that...

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to Micro B plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any computer that...

As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a Micro B USB jack and a USB C plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Since it uses a new connector, you may have lots of cables and power supplies that...

This here is your standard A-microB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your NETduino, Arduino Leonardo, Raspberry Pi (among other things). Approximately 6.5" long from end to end, its a little more compact than our classic 3' long cable We had these made to our specifications, available in Adafruit Black

This is your standard USB A-Plug to Micro-USB cable. It's 2 meters long so you'll have plenty of cord to work with for those longer extensions. Perfect for connecting to your Raspberry Pi, Arduino Leonardo/Micro, FONA or Trinket (among other things). It's got extra beefy 24 AWG power wires so it works great for high power (1-2 Amp) computer powering. If you want...

Turn any USB Type C device into a pluggable USB key with this 'plug to plug' adapter. Works with Windows / Linux computer/laptops with a USB type C port. This adapter doesn't work with Macbook laptops due to a mistake in the design: The CC1/CC2 pins should only be connected once but they are connected both times - that means that Power Delivery chips get confused and...

Double up on your micro USB capabilities with the Micro B USB 2-Way Splitter Cable. This splitter is great for reducing cable clutter and freeing up port space. It takes a single Micro B connection (with data and power) and gives you two outputs. The longer cable has data and power brought to it. The shorter cable is only power. You can also use it just for power...

This is a magnetic USB micro b plug! They pair with the Black Woven USB A or Type-C to Type-C Cable with Magnetic Tip . Plug your microUSB power (or data!) cable into one end, then insert the little magnetic nub into your device's charging port. Now you basically have a quick-detach microUSB connector with a magnetic alignment. Easy to plug in whenever, no worries if...

Ready Players 1 and 2? Double up on your MakeCode gaming with a Sync Cable! We got this Micro B USB to Micro B USB cable specially made to connect you and your frenemy for co-op fun or player-versus-player showdowns. Works with our PyBadges and PyGamer - we connected the JACDAC pin to the 'extra' ID pin of the Micro B cable so data can pass back and forth. It's one...

If you'd like to connect a Micro-B connector to your favorite garment to make a fun wearable tech project, then try out the array of sewable connectors we have. This is a Micro-B connector that is oriented in a horizontal position to the sewable base it's housed on with red and black wires running through the bottom. The jack is molded into a rubber that can be hand...

At first glance this appears to be an ordinary A to micro B USB cable. Plug it in to your device and power supply, and you get a colorful glitter of dozens of little LEDs embedded in the length of the cable. Can be used for data and charging. The LEDs are luminous but not too bright. Perfect for vampire makers, candy ravers, or maybe night owls who misplace their...

At first glance this appears to be an ordinary A to micro B USB cable. Plug it in to your device and power supply, and you get a colorful glitter of dozens of little LEDs embedded in the length of the cable. Can be used for data and charging. The LEDs are luminous but not too bright. Perfect for vampire makers, candy ravers, or maybe night owls who misplace their...

This USB micro B "JIG" Dummy Plug is a small, handy device for those interested in debugging their smartphones or other devices that use the ID pin #4 for a special signal. This plug has a 300K resistor from the ID pin to ground, which can be used to resuscitate Samsung S4, S5, S6 and possibly others by putting into an emergency repair mode. It's also useful for...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting any development board, microcontroller, mobile phone, or other device to your computer or charger. "Standard?" you might say... nothing gets past the astute eye of an Adafruit customer! Why yes, that is an LCD display embedded in the cable! This is basically like a USB cable...

Linguine? Rice sticks? Soba? Whatever your favorite noodle may be, you will be pleasantly reminded whenever using this noodle-shaped cable. This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0 - but in a slim profile and classic Adafruit Black. Perfect for connecting a PC to your Arduino Leonardo/Micro, Raspberry Pi, NETduino, (among other things)....

Your cell phone charges off of USB, but can you really trust that charging station at the airport? Now you can control when to allow data in or out of your device with this little USB extension cable. It can be used with any device that has a micro USB port, which is like just about anything except for Apple devices. Voila! Your cable's data lines can now be switched...

This cable is super-fashionable with a woven pink and purple Blinka-like pattern! First let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible cables, then you might as well have the nicest fabric-bound cable with a eye-catching python pattern. Perfect for connecting to your PyPortal, Circuit Playground Express,...