Cables / Cable Assemblies / JST

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in the middle, try this switched extension cable. Finally, for PCB and breadboard...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors...

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and...

By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in...

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together! This is an A-A cable, that...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with female socket headers on the end For more information about JST PH...

These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or...

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to match up with our STEMMA boards and sensors that have 3-pin connections - and the wires are even color coded! Red is power,...

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and STEMMA JST PH connectors on the other. You can sand down the center-nub key on the JST PH side to make it fit in a Grove connector. Chunkier JST PH connectors come with 2mm pitch, and JST SH (also...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the...

These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming apart...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug connectors on the...

This cable will let you turn a JST PH 4-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND. Red for V+. White for SDA. Green for SCL. Even though this is a JST PH connector, it will fit into a Seeed Grove connector and...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

If you'd like to make a connection to a board or breakout with Seeed Grove connection, this 100mm long 4-wire cable is fitted with a Grove connector and four bare wires. Please note you will have to watch for voltages on the power/signal pin when using 3V-only sensors, because Grove boards that are 5V logic like many Arduino UNO-compatibles. The colors are: Black for...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug/pin connectors on the...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the...

These 6-wire cables are 162mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 6 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

These 5-wire cables are 168mm (6.6") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 5 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

This product's about as simple as a cup of lemonade on a hot summer day. And, like lemonade, it's just three components! This board is a sewable adapter with a 3-pin JST wiring adapter. It's a perfect way to add a simple link between things like our Flora NeoPixels and more complicated products like our NeoPixel Rings. There are three holes on the board that are...

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can undo without tearing the contacts from the housing. Plugs in nicely all with our...

This cable is a little over 100mm / 4" long and fitted with JST-GH compatible 6-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily, and the wires are even color coded! These would go great with SEN54 or SEN55 all-in-one air quality sensor modules from Sensirion For more...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with male socket headers on the end For more information about JST PH...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and a Grove connector on the other. This cable can be used with STEMMA or STEMMA QT / Qwiic boards to easily connect sensors and drivers from one board to the other. Please note you will have to watch for...

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! We also carry the socket 'mating' version of this cable over here. For more information about JST PH connectors, visit the JST website

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers!...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 3-pin 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. Can also be used with any STEMMA breakouts! This cable has a JST PH 4-pin on one side and alligator clips on the...