Coin Cell

20mm Coin Cell Breakout Board (CR2032)

PRODUCT ID: 1870

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy...

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. Comes with one fully assembled and tested coin cell battery holder and a small stick of 0.1" header so you can solder it on and plug into a breadboard. Coin cell battery is...

$2.50

IN STOCK

2 x 2032 Coin Cell Battery Holder - 6V output with On/Off switch

PRODUCT ID: 783

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most popular size) in...

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most popular size) in series to generate 6V nominal. (If you want only 3V, we suggest sticking a crumpled piece of tin foil in one of the slots.) 20mm coin cells are popular as they are used in keychain lights, so they are easy to get, and fairly low cost. They tend to have about 220mAh capacity so this holder would...

NOTIFY ME

$1.95

OUT OF STOCK

20mm Coin Cell Breakout w/On-Off Switch (CR2032)

PRODUCT ID: 1871

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout...

Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. There's two ground pins, one 'switched' power pin, and one pin that is always on. Comes with one fully assembled and tested breakout plus a small...

$3.50

78 IN STOCK

Sewable CR2032 Battery Holder

PRODUCT ID: 653

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in...

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (negative) and the other tab is +3 Volts. This holder is meant to be used with Lithium CR2032 (20mm diameter, 3.2mm thick) sized coin batteries. These are almost always 3V at...

$1.95

IN STOCK

12mm Coin Cell Breakout w/ On-Off Switch

PRODUCT ID: 1867

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for...

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. There's two ground pins, one 'switched' power pin, and one pin that is always on. Comes with one fully assembled and tested breakout plus a small stick of...

NOTIFY ME

$2.75

OUT OF STOCK

12mm Coin Cell Breakout Board

PRODUCT ID: 1868

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy connecting....

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar. Comes with one fully assembled and tested coin cell battery holder and a small stick of 0.1" header so you can solder it on and plug into a breadboard. We also have a version with an...

$1.95

4 IN STOCK