Raspberry Pi / Raspberry Pi B+, Pi 2, & Pi 3 / Pi HATs and Plates

It's 10 PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS, so you can add precision time and location to your Raspberry Pi Model Pi 3, Pi Zero, A+, B+, or Pi 2, 3, 4, & 5. Here's the low-down on the GPS module: -165 dBm sensitivity, 10 Hz updates, 99 search channels. GPS +...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM...

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Raspberry Pi and motors are not included. Works with any and all Raspberry Pi computers with 2x20 connection port. Since the Raspberry Pi does not have...

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high-speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all, it plugs right in on top of your Model A+ or B+ and...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED,...

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like touch-reactive tablets and phones, as well as control panels for appliances, which is where...

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what normally would go out the HDMI port come up on a nice little flat screen. *Its not technically...

"These go to eleven." 11 millimeters that is! Our Black Plated M/F Brass Standoffs are engineered specifically to keep your Pi HAT snug on your Pi while also keeping the two boards separated, in particular, the HDMI port. These standoffs can also be screwed into each other allowing stacking multiple HATs on to one Pi! They're the perfect companion for any Pi Hat...

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what normally would go out the HDMI port come up on a nice little flat screen. * Its not...

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories with extra tall headers properly secured while also keeping the two boards separated. These standoffs can also be screwed into each other just like the 11mm versions (made for...

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto any modern Raspberry Pi computer with 2x20 headers It's harder to use than the Thru-Hole type headers, because you have to do some SMT soldering, but for the slickest, slimmest fit, this header is recommended! Note that because the connectors go out...

Control the same hardware as used in space... build your very own Astro Pi with the new Raspberry Pi Sense HAT! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘Astro Pi’. The Sense HAT has several integrated circuit based sensors can be used for many different types of experiments, applications, and...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible with Raspberry Pi 3 B+...

Cyber-warriors, listen up here! We’ve got with some zero-day unreleased hardware we just dumpster-dived. Now you can crack kodes, and write skripts with style, thanks to the CYBERDECK HAT for Raspberry Pi 400 & 500 from Adafruit zaibatsu. This is the same hardware Kevin Mitnick used when he popped Sidewinder! Ok, maybe not, but it will definitely let you...

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. We basically took our super-popular DC+Stepper Motor HAT and squeezed it down and made it fully assembled - plug and play ready to go, no soldering...

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Take control of and monitor your world with Pimoroni's Automation HAT -- an ultimate jack-of-all-trades Raspberry Pi HAT! With relays, analog channels, powered outputs, and buffered inputs (all 24V tolerant), this home monitoring and automation...

The SparkFun Qwiic pHAT V2.0 for Raspberry Pi provides you with the quickest and easiest way to enter into SparkFun’s Qwiic or STEMMA QT ecosystem while still using that Raspberry Pi that you’ve come to know and love. The Qwiic pHAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic/QT connectors on the HAT. Since...

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter SparkFun’s Qwiic / STEMMA QT ecosystem when using that Raspberry Pi that you’ve come to know and love. The Qwiic HAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic connectors on the HAT. Since the Qwiic system allows for...

The Raspberry Pi Build HAT (Hardware Attached on Top) is a new add-on board for your Raspberry Pi. It connects to the 40-pin GPIO header and can be used to control up to four LEGO Technic motors and sensors from the LEGO Education SPIKE Portfolio. The cool design of the Build HAT means that all the components are on the bottom, leaving room on the top of the board...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT or pHAT on your Raspberry Pi Model Zero, 5, 4, 3, 2, A+, or B+ (any Pi with a 2x20 connector). The Pimoroni Mini Black HAT Hack3r is ideal for debugging your (p)HAT projects or combining a (p)HAT with other circuits. Features: HAT & pHAT spec...

A versatile motor, servo, and audio driver HAT for Raspberry Pi. Bring your mechanical inventions, creations, and contraptions to life! Inventor HAT Mini helps transform a Raspberry Pi computer into a robot, prop, kinetic sculpture, creepy automaton, or any other exciting moving thing. Want to drive a couple of fancy motors with encoders (or hook up standard motors...

The Rainbow HAT from Pimoroni has a buffet of sensors, inputs, and displays to explore Android Things™. Use it as a weather station, a clock, a timer or stopwatch, a mood light, or endless other things. Pimoroni collaborated with the Android Things™ team at Google to create this great add-on board that features displays, sensors, sound, and lots of LEDs!...

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2/3/Pi 4 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. Currently the Matrix driving software library does not support the...

Is this not the cutest little display for the Raspberry Pi? It features a 2.4" display with 320x240 16-bit color pixels and a resistive touch overlay. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! It's designed to fit nicely onto the...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected...

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry Pi. Mini proto area for adding components. Add standard male or female headers for breadboard like...

Discontinued - you can grab the Pimoroni Unicorn HAT HD instead! Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi. Unicorn HAT provides a wash of controllable color that is ideal for mood-lighting, 8x8 pixel art, persistence of vision effects, status indications, or just blasting...

Discontinued - you can grab this Leap Motion Controller 2 instead! Control your Raspberry Pi 3, 2, A+, B+, or Zero with a flick of the wrist! The Pimoroni Skywriter HAT senses the position of your fingers in the air above. Using Pimoroni's Python API you can read off the positional data (x, y, z) and common gestures like flick left, tap, and double tap. Electrical...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT on your Raspberry Pi Model Pi 3, 2, A+, or B+. The Pimoroni Black HAT Hack3r is ideal for debugging your HAT projects or combining a HAT with other circuits. Features: HAT spec landing area with PCB standoffs. Includes 40 pin GPIO ribbon cable. All...

Discontinued - you can grab this Pimoroni Inventor HAT Mini for Raspberry Pi - PIM672 instead! The Explorer HAT Pro is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer Pro from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors,...

The Explorer HAT is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features: 4x buffered 5V tolerant inputsHook up...

Raspberry Pi - meet your new musical B.F.F! With the Pimoroni Piano HAT you can control hardware synthesizers and software synths or play some really beautiful music in Python. Surprise everyone with your creativity, maybe even yourself! This HAT comes with 16 touch sensitive buttons, up and down octave controls, and 13 piano keys from C to shining C! Each button on...

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female header. This header allows you to plug your Raspberry Pi HAT onto a Raspberry Pi A+, B+ or Pi 2. We also carry various through-hole versions but this is for when you really need to have all the space available, such as on our 3.5" PiTFT

The Pimoroni Display-O-Tron HAT is an upgraded HAT version of our Display-O-Tron 3000! The Display-O-Tron is a lovely 16x3 character LCD display with capacitive touch pads, GPIO breakout pins, and a six-zone RGB backlight (twice as bright as the older Display-O-Tron 3000)! The capacitive touch pad is ideal for navigating on-screen menus or inputting data and there...

The Pan-Tilt HAT from Pimoroni lets you mount and control a pan-tilt module right on top of your Raspberry Pi. The HAT and its on-board microcontroller let you independently drive the two servos (pan and tilt), as well as driving up to 24 regular LED (with PWM control) or NeoPixel RGB (or RGBW) LEDs. There's also a handy slot through which you can route the servo,...

Over one hundred RGB LEDs, all individually-controllable, and four tactile buttons. It's the ultimate pocket-sized rainbow generator for Raspberry Pi! Unicorn HAT Mini is a 17x7 matrix of RGB LEDs that can be controlled, both in terms of color and brightness, to display animations, text, simple images, and more. The four tactile buttons add tonnes of utility to...

For when two (mini) HATs are better than one! A nifty prototyping tool for connecting multiple mini HATs (a.k.a. Bonnets, pHATs, Zero-HATs, etc!) to one Pi. This HAT gives your Pi two sets of GPIO pins - very useful for attaching two mini HATs (or a HAT and a mini HAT) at the same time, great for prototyping, debugging, or for connecting a mini HAT to other...

Automate your world with Automation HAT Mini! Monitor and control up to 24V systems and see their status on the gorgeous full-colour display. Don't be fooled by its size... Automation HAT Mini packs a whole bunch of functionality in. It has a relay, 3x buffered inputs 3x outputs, and 3x analog inputs, all 24V-tolerant. Last but not least, it has a beautiful 0.96"...

If you're building a Raspberry Pi project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most cases. However, WiFi does not have a long range and also requires both investment (through your ISP) and setup (routers, access points, network security schemes). If you're deploying your project somewhere more remotely,...

Discontinued - you can grab Raspberry Pi PoE+ HAT instead! Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the...

Pimoroni's GFX HAT is a shiny new LCD Display with RGB Backlight and Touch Buttons! This is a seriously snazzy LCD that can display complex graphics for all your headless Pi games and animations. While the LCD is monochrome 128x64 pixels, the backlight can be set to different RGB colors to indicate You also get six capacitive touch buttons for input and navigation,...

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's pHAT Stack! This expansive breakout PCB offers 6 sets of 2x20 pin headers - one for connecting to your Pi and the other 5 for a plethora of HATs, pHATs or bonnets. The combinations are endless... It's perfect for your projects, displaying temperatures, times, etc. and becomes...

Unicorn HAT HD crams 256 RGB LEDs, in a 16x16 = 256 LED matrix, onto a single HAT. High-definition rainbow goodness! You can still use it for all of the same things as the regular Unicorn HAT, but with four times as many pixels it makes much more complex animations possible, including scrolling text, and even low resolution videos. The bundled ninja diffuser makes...

Pimoroni's Nano HAT Hacker gives you full access to all 40 pins on your Pi, broken out at the top. It's a super-skinny 0.8mm PCB, so you can solder it right onto the pins on your Pi and still have enough height on a standard header to fit a HAT or pHAT on top. This item used to be called the "Pico HAT Hacker", the name is now "Nano" to reduce confusion with the...

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT. It's the best, easiest way to make a super-sweet arcade system using any Raspberry Pi. Simply pop it onto your Pi, plug your Pi power supply into the USB-C connector on the Picade HAT (it back-powers your Pi through the GPIO, so no need for a separate power...