Cables

These little cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits, and have a few handy in our ARM-dev box. We thought you may want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is...

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board to the other....

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can undo without tearing the contacts from the housing. Plugs in nicely all with our...

This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. We think this would be most useful when putting a Beagle Bone, Raspberry Pi, Arduino Ethernet into a box. The jack half has two mounting 'ears' with 4-40 screws installed, 1" inch / 25mm apart. The ears are flexible so the holes don't have to drilled very...

These Female/Male Extension jumper wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors...

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in the middle, try this switched extension cable. Finally, for PCB and breadboard...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and...

This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. We think this would be most handy when putting a Beagle Bone, Raspberry Pi or Mintyboost into a box. The jack half has two mounting 'ears' with 12mm M3 screws installed, 30mm apart. The ears are flexible so the holes don't have to drilled very precisely....

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board...

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Block Breakout. You get a nice solid PCB with an DE-9 socket and two strips of terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. Perfect for when you need a non-standard wiring setup or interfacing to an older...

Wouldn't it be cool to drive a tiny OLED display, read a color sensor, or even just flash some LEDs directly from your computer? Sure you can program an Arduino or Trinket to talk to these devices and your computer, but why can't your computer just talk to those devices and sensors itself? Well, now your computer can talk to devices using the Adafruit FT232H breakout...

These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

This RF adapter cable is super handy for anyone doing RF work. Often times, small electronics save space by having a pick-and-placeable u.FL connector (also called uFL, IPEX, IPAX, IPX, MHF, and AM). But most antennas have SMA or RP-SMA connectors on them. This little cable will bridge the two! This cable is RG178 and is 15cm (5.9") long not including the SMA...

This product is a 3-in-1 cable. By itself, it can act as an extension cord for any 5.5/2.1mm DC power cable. The heavy 24 AWG wires can handle up to 5A. You can also cut it half to make two barrel cables (one plug and one jack). This will allow you to connect a classic 'wall wart' to a breadboard or PCB without having to solder in a bulky power jack. Or you can use...

This cable is a little over 100mm / 4" long and fitted with JST-GH compatible 6-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily, and the wires are even color coded! These would go great with SEN54 or SEN55 all-in-one air quality sensor modules from Sensirion For more...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

Throw out all those Mini and Micro B USB cables you have in a plastic bin - the next generation of USB connectors is here with USB C! You've seen these connectors pop up on all sorts of devices, as the industry moves from micro B or lightning to the new standard. Well, at least until the next standard comes out USB C features a symmetric/reversible connector, more...

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to match up with our STEMMA boards and sensors that have 3-pin connections - and the wires are even color coded! Red is power,...

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together! This is an A-A cable, that...

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USBSerial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the...

As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around a USB Type A hub, computer or laptop. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among...

By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in...

If you've got a computer or laptop with a USB C port, but you're itching to use one of our fancy new Trinkeys, this adapter will do an excellent job at turning that USB Type C port into a USB A port! Works great with any device that has a USB C port. These adapters don't magically give you USB C speeds into a USB 2.x device, and they won't give you the power...

This Simple USB Type C breakout is kinda interesting, it looks similar to this USB Type C SMT Inline Breakout Board, but it's an 'inline' style with pads for soldering to the common USB 1.1/2.0 connections. We see this lil breakout used often in custom keyboards, it's glued or wedged into the enclosure. Unlike our breakout, it doesn't break out all the pads - it just...

When 0.1" is too big, and JST PH's too chunky, the ultra-slim "PicoBlade" is a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. This cable is nice and long, 200mm in fact. It's got both small form factor (won't take up a lot of real estate on your PCB) and friction lock to make easy-breezy connections to your HalloWing or anything...

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box. The jack half has two mounting 'ears' with M3 screws installed, ~1.1" / ~29mm apart. Can be used with box walls 0.125" to 0.25" wide. Depending on your usage you may...

We now have a handy extension cord for JST-XH projects! One end has a JST-XH socket, and the other has a matching plug. Between the two, 500mm of color-coded wire. This solid 2.5mm pitch connector extension cable is great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. The two...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight HDMI plug. Ribbon cable and other adapter not included!...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this USB C Jack to USB C Jack Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with male socket headers on the end For more information about JST PH...

This panel mount cable will allow you to enclose a device that has a USB A port. Perfect for placing your project in a secure box. Both ends have standard USB A, an extension cord if you will. What's special about this, you ask? It's a Snap-In Panel Mount Cable - much easier than a classic panel mount cables, you don't need screws or drills for installation. Cut out...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long

Connect two HDMI devices together and save space with this basic flat HDMI 1.4 cable. It has nice molded grips for easy installation, and is 1 foot long (~30 cm). This cable is absolutely perfect for an LCD Raspberry Pi project. The cable is so thin and flexible that you won't have any loose dangling HDMI cables getting in the way, and you can even fit your Pi behind...

If you'd like to connect a USB-host-capable chip to your USB peripheral, this cable will make the task very simple. There is no converter chip in this cable! It's basically a plain USB cable that's cut in half and with jumper sockets on the power and data lines. Simple to use, does the job when you have something that exposes the D+/D- pins. Red wire connects to 5V...

This panel mount cable will allow you to enclose a device that has a USB Micro B port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Micro B plug connector, and other is a USB C socket with special over-molding. The socket side has two mounting 'ears' with M3 screws installed 20mm...

If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45 Ethernet Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing Ethernet kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY MicroB Male connector. It's a little more elegant because instead of snapping two pieces together the connector press-fits into the overmolding for a modern look. We also carry the slim size in USB-A male and USB-microB female....

What do you do when you want to tinker with GPU hardware, but you don't have a display on hand? This HDMI Dummy Plug is a small device that acts as a display emulator. Once it's plugged into the video output socket on your device or computer, the plug punks the operating system into detecting a connected display, and voilà! Now you have unimpeded access to...

As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around a USB Type A hub, computer or laptop. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among...

If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 10 cm (~4 inches)...

One of the most common converter cables you'll want in your cable collection - this 32" long cable converts a standard 3.5mm stereo jack to pigtail wires. Ground ring is black, middle ring is white and tip is red. Cable is 32"/81cm long from end to end. Right-Angle 3.5mm Stereo Plug to Pigtail Cable (4:49)

This 40-pin FFC / FPC Extender is very simple. It lets you connect two 40-pin 0.5mm pitch FFC (Flexible Flat Cable) / FPC (Flexible Printed Circuit) cables end-to-end and extend the length. For use with 0.3mm thick FPC cables. Note that pin 1 of one cable is connected to pin 40 of the other so you need to use a cable that has contacts on the same side (type A cable)...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and a Grove connector on the other. This cable can be used with STEMMA or STEMMA QT / Qwiic boards to easily connect sensors and drivers from one board to the other. Please note you will have to watch for...

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and STEMMA JST PH connectors on the other. You can sand down the center-nub key on the JST PH side to make it fit in a Grove connector. Chunkier JST PH connectors come with 2mm pitch, and JST SH (also...

If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Right Angle USB Micro B Plug Down only. (We also have the matching 'up'...

Connect this to that with an IDC cable! This cable has 6 pins (2x3) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto either side, they're quite sturdy!

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) HDMI plug. Ribbon cable and other adapter...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with female socket headers on the end For more information about JST PH...

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has...

If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 20 cm (~8 inches)...

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming apart...

As technology changes and adapts, so does Adafruit, and speaking of adapting, this right angle adapter is USB C socket-to-plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB A correctly the first time? Works great with any...

If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB C Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project. The adapter can fit holes 21.5mm to ~27mm, so you can drill in your wood, plastic, or metal with a common hole-saw or bit, no special shapes or filing...

When you want a svelte USB C build, a 'sunken' type connector that straddles the PCBA will let you keep your build super slim. This breakout gives you all the contacts for a USB Type C connector, but lower than the classic 'horizontal' USB-C breakout and a vertical version. USB C features a symmetric/reversible connector, more data pins, and higher current output...

These cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits and have a few handy in our ARM dev box. We thought you might want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is 0.06mm/0.025"...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has header pins, so it could be used to connect to socket...

Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your every-day serial data from a microcontroller to computer. What now? Enter the Adafruit CP2102N Friend! The CP2102N is very similar to the CP2104. Despite having a name with a lower number, its actually considered the...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

If you need to add a panel-mount connection for USB Micro B, but don't have the time or ability to cut a custom oval or square hole, this Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your existing micro-B USB kit. The adapter is about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (L) Micro HDMI plug. Ribbon cable and other adapter...

This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 12V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotation...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

Stretch out your servo connections with this flexible servo extension cord. It has a 3 pin shrouded "male" connection to plug your servo into and then, 50cm later, a 3 pin female connection. It even keeps the common red/black/white color coding. A great add-on to our 16 channel PWM/Servo driver and goes with all the servos we carry.

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different...

If you're messing around with floppy drives, or disk drives, or other devices that are usually powered with a PC motherboard you'll often see these big 'Molex' connectors used to provide power. They are used to give 5V (red), 12V (yellow) and ground (black) and with this connector you can easily wire up your favorite power supply or bench-top power source. We also...

Give your 50 pin, 0.5mm pitch, devices a strrrreeeetch with this extension board. This 50pin FPC extension board has two 50-pin flex connectors, and an extension cable to add ~22cm (20cm cable plus 2cm board) Each order comes with one board a 20cm long, 50-pin 0.5mm pitch FPC cable and board. Works great with our 50pin TFTs, or anything else with the same kind of...

If you need to add a panel-mount connection for DC power, but don't have the time or ability to cut a custom oval or square hole, this Round Panel Mount 5.5mm/2.1mm DC Barrel Jack Extension Cable is the easiest and fastest way to panel-ify your existing project. The outer flange is 30mm in diameter, and the threaded part is 23mm diameter, so you can drill a 1" hole...

This panel mount cable will allow you to enclose a device that has a USB A port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Type A plug connector, and other is a USB C socket with special over-molding. The socket side has two mounting 'ears' with M3 screws installed 20mm apart....

These Female/Male 'Extension' Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on...

Just about all electronics use TTL serial for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. This is a USB to TTL serial cable, with a FTDI FT232RL usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels....

This panel mount cable is great for making USB Type C connections with a panel-mount setup. On the small panel-mount side you get a USB C connector, the other end has power, ground, D+ / D-, and CC1/CC2 lines. We particularly like that the panel mount part is very small, only about half an inch in diameter, and you get a JST PH cable on the other end for quick...

If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required....

This power jack is designed to easily attach to a panel up to 8mm thick (0.315" or 5/16") and fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project enclosure. We like this jack in particular for its long body (so you can use it on thicker wooden panels), sturdy PCB spacer with 3 easy-to-solder eyes and 'forgiving' plastic lip...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around a USB Type A hub, computer or laptop. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT 4-pin JST SH on one end, and Arduino MKR (ESLOV) 5-pin JST SH connectors on the other, with the wires spun around so you can use it to connect STEMMA QT sensors we've got to any of the popular Arduino MKR boards! JST SH (also known as Qwiic)...

These Female/Male 'extension' jumper wires for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on...

Connect this to that when a 22-pin FPC connector is needed. This 20 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on one side will match with pin one on the other. How handy! We're stocking this to fit with the new Raspberry Pi 5 and our RP2350 boards with 22-pin HSTX connectors, but you could, of course, use it for anything that needs...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers!...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) Micro HDMI plug. Ribbon cable and other...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header. The best...

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two #4-40 screws are used to attach the female socket end, 26.9mm apart. Two hex-body standoff-screws are included as shown above and the hex nuts are embedded inside the molded end. Cable is 40cm long...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug/pin connectors on the...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper connector with easy-to-solder tabs. USB DIY Connector Shell - Type Mini-B Plug (4:59)

We have some great waterproof and weather-proof items in the adafruit shop, but once you have a project built, you'll want to enclose it. But how to keep an enclosure weather/waterproof while still attaching cables for power, data or sensors? That's where cable glands come in. By installing these over the cable, they form-fit to make a seal, keeping your project box...

If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that with an Ethernet Jack - this adapter will come in very handy! No soldering required. Just use a slim screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire and re-tighten. Note that these aren't recommended for actual Ethernet traffic, especially long term...but for...

Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 2 meter long (about 6 feet). This is a HDMI 1.3 cable. Works great with a BeagleBone or Raspberry Pi 4 Micro HDMI to HDMI Cable - 2 meter (0:47)

Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a mess of wires. There is an official Power-over-Ethernet standard that allows devices and routers to...

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no longer, simply pick up one of these to solve any rotation needs you have. Inside the miniature plastic tube is a gold plated slip ring for 6 wires. There...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug connectors on the...

If you'd like to make a connection to a board or breakout with Seeed Grove connection, this 100mm long 4-wire cable is fitted with a Grove connector and four bare wires. Please note you will have to watch for voltages on the power/signal pin when using 3V-only sensors, because Grove boards that are 5V logic like many Arduino UNO-compatibles. The colors are: Black for...

This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 12V DC output, at up to 3A (or whatever the power adapter can do) Please note: If your USB...

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Spring Block Adapter. You get a nice solid PCB with a DE-9 socket and one line of push-terminal blocks. Just flick up the little levers and slide in your stranded or solid core wire to quickly assemble your own wiring jigs. No soldering required! Perfect for when you need...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

Check out this handy MicroUSB extension cable, which will make it easy for you to enclose a device that has a B type (micro USB host) port. Great if you need to extend the USB port for your Raspberry Pi, Arduino, Feather or really anything development board. This Micro-B male/female extension cable features a male USB Micro-B plug on one end, and a bulkhead mountable...

This panel mount cable will allow you to enclose a device that has an HDMI port. Perfect for placing your project in a secure box. Both ends have HDMI connectors, an extension cord if you will. What's special about this, you ask? It's a Snap-In Panel Mount Cable - much easier than a classic panel mount cables, you don't need screws or drills for installation. Cut out...

If you have a USB Type C port on your computer over here and you want to connect something over there then this extension cable will do the job right quick! This cable is 2 meters long, with all the pins connecting from one side to the other.

If you need to add a panel-mount connection that extends a micro SD card, this Round Panel Mount MicroSD Adapter Plug is the easiest and fastest way to panel-ify your project. The adapter is about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut,...

Here's an easy solution for keeping your USB C devices free from dust and other unsavory particulates. These squishy Silicone USB C Dust Cover Inserts slip neatly into any computer or device with a USB C socket, from the Adafruit Feather STM32F405 Express to the Raspberry Pi 4. Comes in a pack of ten, so you're set even if you have a computer with a lot of ports, or...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 5V DC output, at up to 3A (or whatever the power adapter can do) Please note: This adapter...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a USB A plug and a USB C socket so your older computer or laptop can catch up to the latest USB Type C. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us...

Connect this to that when a 22-pin FPC connector is needed. This 10 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on one side will match with pin one on the other. How handy! We're stocking this to fit with the new Raspberry Pi 5 and our RP2350 boards with 22-pin HSTX connectors, but you could, of course, use it for anything that needs...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different...

What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more like Tip-Ring-Sleeve. This nifty, gold-plated connector is known by many names, phone plug, phone jack, headphone jack, jack plug, etc. Used to transmit stereo audio signals, these connectors are a mainstay in audio equipment, especially speakers and microphones. For audio,...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

This 9-pin cable is just about 100mm / 4" long and fitted with JST-SH female connectors on both ends. Compared with chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel and are easy to insert and remove. We got these especially for our fantastically spooky Adafruit MONSTER M4SK in case you'd like to split the mask in two and...

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, BeagleBone, or any other Mini-B device into a box! This Mini-B male/female extension cable features a male USB Mini-B plug on one end, and a bulkhead...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (left bend) HDMI plug. Ribbon cable and other adapter...

If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 50 cm (~20 inches)...

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a straight Mini HDMI plug. Ribbon cable and other adapter not...

6" (150mm) long jumper cable of 6 conductors, 0.1" spacing with two 'female'/sockets on either end. Great for wiring up ShiftBrites together! Note: Wire colors may vary.

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one cable, and then separates the data (Ethernet) and power (+12VDC regulated) into two different...

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! We also carry the socket 'mating' version of this cable over here. For more information about JST PH connectors, visit the JST website

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

Stretch out your servo connections with this flexible servo extension cord. It has a 3 pin shrouded "male" connection to plug your servo into and then, 30cm later, a 3 pin female connection. It even keeps the common red/black/white color coding. A great add-on to our 16 channel PWM/Servo driver and goes with all the servos we carry.

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to Micro B plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any computer that...

Quantum superposition is a physics concept that light and matter can be both particle and wave at the same time. This amazing phenomenon can be demonstrated at home when you try to plug in a USB Type A cable in, it's both right-side-up and upside-down at the same time! That's why you have to try at least 3 times to plug it in. The Adafruit Reversible USB Type A Plug...

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Has a nice soft flexible 20-line 0.05" ribbon cable and keyed IDC connectors. Good for JTAG connections, in particular - but is useful for anything really. This cable is 12" long and has 20 pins (2x10) in 0.1" x 0.1" spacing and two sockets crimped on...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

This handy USB extension cable will make it easy for you to enclose a device that has a B type port. We think this would be most handy when putting an Arduino in a box. The jack half has two mounting 'ears' with M3 screws installed, 1.1" / 29mm apart. Can be used with box walls 0.125" to 0.25" wide. If you have a thinner-walled box, simply swap out the M3 screws for...

Turn a micro HDMI port into a 'regular sized' HDMI port with this handy adapter. Works great with the Beagle Bone Black, many cameras with video out, etc. Approximately 7" long. Micro-HDMI to HDMI Socket Adapter Cable (0:27)

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

For big projects, with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. Only problem is that these supplies have connectors that only plug into motherboards or hard drives. That's where this cable comes in. It has a matching 4-pin molex connector to the hard drive/CD-ROM power cables that come out of a power supply so you can use this...

If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 30 cm (~12 inches)...

If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Straight USB Type A Male Plug only. Ribbon cable and other adapter not...

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

Connect this to that with an IDC cable! This cable has 10 pins (2x5) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto either side, they're quite sturdy!

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

This RF adapter cable is super handy for anyone doing RF work. Often times, small electronics save space by having a pick-and-placeable u.FL connector (also called uFL, IPEX, IPAX, IPX, MHF, and AM). But most antennas have SMA or RP-SMA connectors on them. This little cable will bridge the two! This cable is RG178 and is 15cm (5.9") long not including the RP-SMA...

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to Micro B plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any computer that...

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Comes in a classic Adafruit Black, has a nice soft flexible 16-line 0.05" ribbon cable and keyed IDC connectors on both ends. It's perfect for use with our GPIO Expander bonnet or with any of our RGB LED Matrices if you want to chain them together or...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

UPDI stands for Unified Program and Debug Interface, but this board is so smol and cute that we will call it the Unusually Playful Device Interfacer and pat its head when it does a good job. It's designed to make programming modern ATtiny chips very easy because it has 3V or 5V power and logic select, power, and transmit indicator LEDs, and a quick cable for poking...

This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 20V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...

This USB Type C breakout is kinda interesting, it looks similar to our right angle USB C socket breakout, but it's an 'inline' style with pads for soldering to the connections. We think it could be handy for making custom cable harnesses! Unlike our breakout, it also has the true dual-row USB C connector and all pads broken out. It does not have any resistors to set...

This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in another USB device. For example, a Pi Zero or Pi Zero W has a OTG port, as does the Arduino Zero, and anything with an ATSAMD21 that is in USB host mode. Also...

Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your every-day serial data from a microcontroller to computer. What now? Enter the FTDI Friend! The FTDI Friend is a tweaked out FTDI FT232RL chip adapter. Sure, like the well-known FTDI cable, it can provide power to your project...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

This panel mount cable is great for making USB Host or (some) client connections with a panel-mount setup. On the small panel-mount side you get a USB C connector, the other end has power, ground and D+ / D- lines. We particularly like that the panel mount part is very small, only about half an inch diameter, and you get a JST PH cable on the other end for quick...

If you need to add a panel-mount connection for USB B, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required....

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

Do you have a S-Video display, projector or monitor that is not compatible with your HDMI devices? Here's an adapter that will allow you to convert HDMI to S-Video, for older video devices that might not have an HDMI input. S-Video has better performance than plain "RCA" composite NTSC/PAL as it separates the color and light level, so if you have a device that can...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper connector with easy-to-solder tabs. USB DIY Connector Shell - Type A Male Plug (3:13)

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy connections...

This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 15V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...

For big projects with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. The only problem is that these supplies have connectors that only plug into motherboards or hard drives. That's where this cable comes in. It has a matching 4-pin Molex connector to the hard drive/CD-ROM power cables that come out of a power supply so you can use...

Give your 40 pin, 0.5mm pitch, devices a strrrreeeetch with this extension board. This 40pin FPC extension board has two 40-pin flex connectors (both are bottom contact type), and an extension cable to add ~22cm (20cm cable plus 2cm board) Each order comes with one board a 20cm long, 40-pin 0.5mm pitch FPC cable and board. Works great with our 40pin TFTs!

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 3-pin 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect...

If you'd like to connect a USB-capable chip to your USB host, this cable will make the task very simple. There is no converter chip in this cable! Its basically a plain USB cable that's cut in half and with jumper sockets on the power and data lines. Simple to use, does the job when you have something that exposes the D+/D- pins. Red wire connects to 5V power (from...

Add a power switch to any USB-powered project simply by plugging this between the USB power port and the USB cable. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a USB A socket on one end and a USB A plug on the other. In between is an in-line switch that is rated for 2 Amps. The data...

Here's an easy solution for keeping your Mini HDMI ports free from dust and other unsavory particulates. These squishy Silicone Mini HDMI Dust Cover Inserts slip neatly into any computer or device with a Mini HDMI socket. Comes in a pack of ten, so you're set even if you have a display or computer with a lot of ports, or if you lose some. We also have these covers...

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no longer, simply pick up one of these to solve any rotation needs you have. Inside the plastic tube is a gold plated slip ring for 6 wires. There are six...

Here's a handy power cable for the RGB LED Matrix Panels we carry. Easily plug into the back of your RGB matrix and insert or screw the power and ground cables onto either the Matrix Portal or the Matrix Bonnet, or whichever microcontroller-and-add-on you're using for your RGB Matrix project. Works with any/all RGB LED Matrices that are 'HUB75' style. Not for use...

Outdoor enthusiasts rejoice! We now have standard 5.5/2.1mm DC power cable sets in a waterproof variety. These cable sets are ideal for projects that must weather the weather: dust, water, rain, snow, tornado (not volcano proof!). They are a little bulkier than normal DC jacks because of the o-ring and removable over-screw. The o-ring is what makes the waterproof...

No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter will be able to get this-connected-to-that. It supports RS232 serial, TTL UART serial, RS485 and RS422. All with quick-connecting screw terminals so you don't need to do any soldering or use special cables. Just plug directly into a computer's USB A port and use...

This 20-pin FFC / FPC Extender is very simple. It lets you connect two 20-pin 0.5mm pitch FFC (Flexible Flat Cable) / FPC (Flexible Printed Circuit) cables end-to-end and extend the length. For use with 0.3mm thick FPC cables. Note that pin 1 of one cable is connected to pin 20 of the other so you need to use a cable that has contacts on the same side (type A-A...

Not to be confused with ODB, OBD stands for On Board Diagnostics and is used for analyzing and diagnosing vehicles. It's the thing your mechanic plugs into to find out why you've got a blinking engine light. Technically, OBD uses CAN bus and, hey, whaddya know, we've got some CAN-capable microcontroller boards here at Adafruit so this OBD Plug (16-pin) to DE-9 (DB-9)...

This 50-pin FFC / FPC Extender is very simple. It lets you connect two 50-pin 0.5mm pitch FFC (Flexible Flat Cable) / FPC (Flexible Printed Circuit) cables end-to-end and extend the length. For use with 0.3mm thick FPC cables. Note that pin 1 of one cable is connected to pin 50 of the other so you need to use a cable that has contacts on the same side (type A cable)...

As technology changes and adapts, so does Adafruit, and speaking of adapting, this wee microadapter has a USB A jack (e.g. it will plug into a computer with an A port) and a USB C socket so your older computer or laptop can catch up to the latest USB Type C. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe...

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy connections...

As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a Micro B USB jack and a USB C plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Since it uses a new connector, you may have lots of cables and power supplies that...

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no longer, simply pick up one of these to solve any rotation needs you have. Inside the plastic tube is a gold plated slip ring for 12 wires. There are 12...

This USB cable adds a DB9 serial port to your computer or laptop. Works with MacOS X, Linux and Windows. Note that this provides (approximately) +-6V serial (RS232) not 5V serial (TTL), good for old devices like GPS, handhelds, programmers, etc with chunky DB9's on the side. Some cheaper RS232 cables 'cheat' and only give you 0-5V which wont work with some devices -...

This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 9V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...

We're now stocking a very fancy Official Raspberry Pi Micro HDMI to HDMI cable with overmolding and Pi logo! It has nice molded grips for easy installation, and is 1 meter long. Perfect for use with your new Raspberry Pi 4 and playing with dual screen setup (you'll need one per Micro HDMI port) Please note that these molded connectors are a little chunkier than many...

Why are bananas never lonely? Because they hang around in bunches! A lot of power supplies, multimeters, and other benchtop equipment use standard 4mm banana plugs to connect this-to-that. When you need more, we now stock them! These are handy stackable and retractable Banana Plug cables! The retracting plastic protection bit on the end will automagically disappear...

Why are bananas never lonely? Because they hang around in bunches! A lot of power supplies, multimeters, and other benchtop equipment use standard 4mm banana plugs to connect this-to-that. When you need more, we now stock them! These are handy stackable and retractable Banana Plug cables! The retracting plastic protection bit on the end will automagically disappear...

Connect this to that when a 22-pin FPC connector is needed. This 5 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on one side will match with pin one on the other. How handy! We're stocking this to fit with the new Raspberry Pi 5 and our RP2350 boards with 22-pin HSTX connectors, but you could, of course, use it for anything that needs...

While this may appear to be an electronic shuriken, it's actually a Multifunctional USB Digital Tester! This handy (pun intended?) tool can measure voltage, current, power, charge time, and other measurements for USB A, Micro B, and USB C! It features a colorful display that pops up when you plug in a power supply. Each click of the button gives you a different...

One truth about working with A/V is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block RCA connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the RCA (Composite Video, Audio) Male Terminal Block. RCA is one of the most...

This cable looks like a USB micro cable but it isn't! Instead of a USB A Plug, it has a USB A Socket on the end. This cable is designed for use with OTG (On the Go) host devices (like the Arduino Due or many tablets) so you can connect a mouse, keyboard, or any other USB device. You'll still need to have drivers on the device, this cable is just a cable and contains...

We don't really know what to call this thing - it's got a 10 pin IDC cable on one end 6 inches of rainbow ribbon and tipped with 0.1" female socket connectors on the ends. We think this would be handy as a 10-pin JTAG breakout adapter, or maybe some sort of cable re-arranger. Anyhow, it seems useful and we picked up a bunch. Yeah we know it would be awesome if we...

This panel mount cable is great for making USB Host connections with a panel-mount setup. On the rectangular panel-mount side you get a USB Type A connector, the other end has power, ground and D+ / D- lines. We particularly like that the panel mount part is very small and snaps in and you get a wire pigtail cable on the other end for quick integration. What's...

If you need to add a panel-mount connection for HDMI, but don't have the time or ability to cut a custom oval or square hole, this HDMI Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing HDMI kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing...

When you need more distance between you and your eInk display, use this 24-pin 0.5mm pitch FPC cable with an extender adapter to streeeeeeeeeetch it out. The cable is generic, but we recommend it for use with eInk because often folks want to mount the displays elsewhere. Just carefully pry open the connector on the eInk Friend, eInk Feather Friend, etc, and use this...

Do you have a display, television, projector or some other older device that isn't compatible with your HDMI devices? Here's an adapter that will allow you to convert HDMI from your modern computer or game system to NTSC/PAL, for older screens and devices that might not have an HDMI input. This mini HDMI to AV signal converter will convert HDMI video signal or audio...

This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 20V DC output, at up to 3A (or whatever the power adapter can do) Please Note: The adapter...

This cable will let you turn a JST PH 4-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND. Red for V+. White for SDA. Green for SCL. Even though this is a JST PH connector, it will fit into a Seeed Grove connector and...

This here is your standard A-microB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your NETduino, Arduino Leonardo, Raspberry Pi (among other things). Approximately 6.5" long from end to end, its a little more compact than our classic 3' long cable We had these made to our specifications, available in Adafruit Black

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

We used a cable like this in a recent build and decided it's perfect for when you want to make a compact USB-C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging, while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...

We used a cable like this in a recent build and decided it's perfect for when you want to make a compact USB-C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging, while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! All you need is this handy PoE module, and access to the center-taps on your Ethernet-capable board. Attach the four input wires, and get regulated 5V 1.8A on the other side. Amazing! This version of the PoE module...

This 24-pin FFC / FPC Extender is very simple. It lets you connect two 24-pin 0.5mm pitch FFC (Flexible Flat Cable) / FPC (Flexible Printed Circuit) cables end-to-end and extend the length. For use with 0.3mm thick FPC cables. Note that pin 1 of one cable is connected to pin 24 of the other so you need to use a cable that has contacts on the same side (type A cable)...

Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.187" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this...

This handy Panel Mount RCA Cable is perfect for component/composite video and audio and perfect for connecting our Raspberry Pi to RCA component/composite screens. This cable comes with two nice RCA connectors and has two 4-40 mounting screws 20mm apart. The cable is 264mm / 10.4" long.

This super slim, super tiny, and super cute Micro-B to USB on-the-go adapter is so slim, tiny, and cute that we'd pinch its cheeks if it was big enough to have cheeks. At just ~15.5mm long, ~11.3mm wide, and ~2mm, this really is the tiniest little adapter we've probably ever seen. But don't let the size fool you - this is a perfect and easy way to turn a device or...

If you need to connect an RJ-45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet socket - this adapter will come in very handy! This is an Ethernet (RJ-45) Terminal Block to Socket Adapter. There is a standard RJ-45 Ethernet socket on one end and a terminal block on the other. No soldering required! Just unscrew the terminal blocks and slide in your...

The premise of this MicroUSB Plug to 5.5/2.1mm Jack adapter is simple. There's a MicroUSB plug on one end and a 5.5mm/2.1mm DC barrel jack with center positive polarity on the other. This allows you to connect one of our 5V 2 Amp, 5V 4A or 5V 10 Amp adapters to something that expects to connect to 5V USB. We also have a shorty adapter-without-cable version Since this...

If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB B Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project. The adapter is about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are approximately 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header contacts on the other. They fit cleanly next to each other on standard-pitch 0.1" (2.54mm) header....

This cable is easy to understand - you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It's also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It's also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection. Black wire connects to sleeve, white wire...

This cable is not only super-fashionable, with a woven pattern in classic Adafruit black, it's also made for USB C for our modernized breakout boards, Feathers, and more. First, let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible cables, then you might as well have the nicest fabric-bound cable. Perfect for...

Often used for floppy drives, 34 pin IDC cables have a 2x17 array of pins. This cable will let you connect one port to another with a festive rainbow design! Both ends have strain relief and keyed connectors. Perfect for retro archiving projects or whenever you have a 2x17 0.1" header on two sides of a board that need connecting.

Connect a device with a Mini HDMI port to a regular sized HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long (about 5 feet). Perfect for use with your new Raspberry Pi Zero!

Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for woven fabric cables. Like, peep this fully reversible pink/purple Blinka-inspired cable or this mithril-like 3-in-1 Sync and Charge cable. Our latest addition to the collection is this 1 meter long Black Magnetic USB A or USB C to USB C Cable with a Magnetic Type C tip!...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

Connect this to that when a 24-pin FPC connector is needed. This 10 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as D style), which means that pin one on one side will match with pin one on the other side. How handy! We're stocking this to use with our e-Ink/e-Paper boards when they have 'flipped' connectors, but you could, of...

Stretch out your servo connections with this flexible servo to alligator clip cable. It has a 3-pin shrouded "male" connection to plug your servo into and then, 17cm later, three alligator clips - it even keeps the common red/black/white color coding for power/ground/signal as you'd expect! This cable is perfect for connecting a servo to something with clip-pads like...

This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things). 3 feet / 1 meter long Color may vary!

We have some great waterproof and weather-proof items in the adafruit shop, but once you have a project built, you'll want to enclose it. But how to keep an enclosure weather/waterproof while still attaching cables for power, data or sensors? That's where cable glands come in. By installing these over the cable, they form-fit to make a seal, keeping your project box...

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Plug to Terminal Spring Block Adapter. You get a nice solid PCB with a DE-9 plug and one line of push-spring terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. We recommend this adapter when you need a non-standard wiring setup or...

Connect this to that when a 24-pin FPC connector is needed. This 5 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as D style), which means that pin one on one side will match with pin one on the other side. How handy! We're stocking this to use with our e-Ink/e-Paper boards when they have 'flipped' connectors, but you could, of course,...

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit. This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It...

We have some great waterproof and weather-proof items in the adafruit shop, but once you have a project built, you'll want to enclose it. But how to keep an enclosure weather/waterproof while still attaching cables for power, data or sensors? That's where cable glands come in. By installing these over the cable, they form-fit to make a seal, keeping your project box...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable clips. There are options a-plenty! This version is a right angle (right bend) Mini HDMI plug. Ribbon cable and other...

We used a cable like this in a recent build and decided its perfect for when you want to make a compact USB C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...

These 6-wire cables are 162mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 6 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

This handy USB extension cable will make it easy to enclose a device with an A-type (USB host) port. We think this would be most handy when putting a Beagle Bone, Raspberry Pi, or Mintyboost into a box. The jack half has two mounting 'ears' with 8mm M3 screws installed, 30mm apart. The ears are flexible, so the holes don't have to be drilled very precisely. Can be...

This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 9V powered devices with a center-positive 2.1mm DC barrel jack from a USB port. We also have a version that provides 12V, and if you just need a passthough...

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no longer, simply pick up one of these to solve any rotation needs you have. Inside the miniature plastic tube is a gold plated slip ring for 12 wires....

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...