These LED strips are fun and glowy. There are 32 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 7-bit PWM precision (so 21-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 2 digital...

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear blue LEDs 5mm diameter 465 nm wavelength 3.2-3.8V Forward Voltage, at 20mA current 6000 mcd typical brightness Viewing Angle : ±10 degrees Maximum continuous current: 30mA If...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 1.5 meters long, and has 20 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

Octolively modules are tileable, digital interactive LED surfaces filled with ultrabright LEDs that respond in complex and gentle ways to stimulus provided by human interaction. Each Octolively module is 4 X 8 inches (10.16 X 20.32 cm) in size, and features eight huge (10 mm) ultrabright LEDs, spaced along a two-inch grid. Each Octolively module also has eight infrared proximity sensors-- one for every LED --to detect nearby motion, even in...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor!...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor!...

Need some big indicators? We are big fans of these huge diffused red LEDs. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 diffused red LEDs10mm diameter660 nm wavelength1.85-2.5V Forward Voltage, at 20mA current1000 mcd typical brightnessDatasheet If you need some help using LEDs, please read our "Introduction to using...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor!...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor!...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 21"/53cm long, and has 10 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

What new iteration of NeoPixel strip is this? Roll out the black light and disco ball! It's an Adafruit NeoPixel   Ultraviolet  Strip with 32 LEDs per meter ! Each order comes as a single one meter long strip. If you order multiple meters, you'll get that many individual 1 meter pieces. The strip is made of flexible PCB material, and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters....

Here at Adafruit we never get tired of new and exotic glowing things. Like moths to the flame, we were intrigued by this new LED technology from Nth Light. Instead of having individual LEDs, Nth prints micro LED diodes onto a flexible plastic substrate for a unique look. The  Nth-Light Narrow LED Flexible Strip Light is printed in three basic processes, starting with standard LED wafers. These wafers are then cut into micro LEDs the...

Here at Adafruit we love discovering new and exotic glowing things. Like moths to the flame, we were intrigued by these fresh  Flexible Silicone Neon-Like LED Strips ! They look a lot like neon, but without the need for expensive transformers, glass tubing or inert gasses. Super flexible and bendy, they feature a single-color non-addressable LED strip with a solid chunk of translucent silicone rubber as a diffuser. They look incredible, and...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 1.5 meters long, and has 30 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 21"/53cm long, and has 10 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...