This is an inverter for EL wire and tape, similar to our pocket inverters, except it is a brick that takes 12V input instead of 2 AA batteries. This means its good for 'fixed' installations since you can just plug it into a 12V wall adapter. It's also good for portable projects where you want to have a big battery pack like a 8xAA holder which will last 4-5 times longer than just 2xAA's. It is also more powerful, and can drive...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Aqua, the brightest and best looking EL color we carry. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL...

A small, portable inverter for EL wire. Powers off of 2 AA batteries (not included!), it can drive 1 to 8 feet (about 2.5m) of our high-brightness EL wire for 10 hours. There is a button for selecting steady/blink/off modes. There's a removable clip on the back. Comes with a 2.5mm pitch female JST connector To connect a piece EL wire to this, you'll want a male connector wire The EL inverter requires a 'load' to stabilize itself....

A small, portable inverter for EL wire. Powers off of 4 AAA batteries (not included!), it can drive 3-4 meters (10 to 13 feet) of our high-brightness EL wire OR 1 meter (3 feet) of EL tape OR a 10cmx10cm piece of EL panel for about 7 hours. There is a switch for selecting steady/blink/off modes. Comes with four 2.5mm pitch female JST connectors, standard for all the EL wire and tape we carry. The JST cables snap into the inverter, so if you...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. This EL is pink-coated so that it looks white. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Red. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change...

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is 10 cm x 10 cm (approx: 4" x 4").There's a plastic coating is about 10.4cm x 10.4cm. Its covered in what seems to be PVC, the tape is thus weather-proof -...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid red. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid blue. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot less power! We've got 2.6mm thickness EL...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in White. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid lime green. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't...

A small, portable inverter for EL wire with an audio input! This inverter has a little microphone and will light the connected EL according to the surrounding audio volume. Makes for an easy reactive project. This inverter requires 6V input (it works great with our 4xAA battery holder) and it can drive 2-3 meters (7 to 10 feet) of our high-brightness EL wire OR 1 meter (3 feet) of EL tape OR a 10cmx10cm piece of EL panel continuously for about...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Orange. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid orange. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid yellow. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Pink. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid pink. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in yellow. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in White Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot less power! This particular model is standard...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't...

A little bundle to get you started! This project pack contains: 5 meters (over 16 ft) of welted EL wire piping in Aqua. 5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change the wire up 2...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Aqua Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project, even the batteries! Includes: 10cm x 10cm (approx 4"x4") square panel in Blue Portable 4xAAA inverter powerful enough to drive a single panel 4 x AAA alkaline batteries to power the inverter and panel for 10 hours For more information and technical specifications, check the product links of...

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is 10 cm x 10 cm (approx: 4" x 4"). There's a plastic coating is about 10.4cm x 10.4cm. Its covered in what seems to be PVC, the tape is thus...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Red Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each of...

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project, even the batteries! Includes: 10cm x 10cm (approx 4"x4") square panel in AquaPortable 4xAAA inverter powerful enough to drive a single panel4 x AAA alkaline batteries to power the inverter and panel for 10 hours For more information and technical specifications, check the product links of...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Blue Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Green Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Aqua Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project, even the batteries! Includes: 10cm x 10cm (approx 4"x4") square panel in Aqua Portable 4xAAA inverter powerful enough to drive a single panel 4 x AAA alkaline batteries to power the inverter and panel for 10 hours For more information and technical specifications, check the product links of...