Raspberry Pi / Raspberry Pi B+, Pi 2, & Pi 3

Raspberry Pi 3 - Model B+ - 1.4GHz Cortex-A53 with 1GB RAM

PRODUCT ID: 3775

The Raspberry Pi 3 Model B is the most popular Raspberry Pi computer made, and the Pi Foundation knows you can always make a good thing better ! And...

The Raspberry Pi 3 Model B is the most popular Raspberry Pi computer made, and the Pi Foundation knows you can always make a good thing better ! And what could make the Pi 3 better? How about a faster processor, 5 GHz WiFi, and updated Ethernet chip with PoE capability? Good guess - that's exactly what they did! The Raspberry Pi 3 Model B+ is the latest product in the Raspberry Pi 3 range, boasting an updated 64-bit quad core...

$35.00

IN STOCK

Raspberry Pi 3 - Model B - ARMv8 with 1G RAM

PRODUCT ID: 3055

Did you really think the Raspberry Pi would stop getting better? At this point, we sound like a broken record, extolling on the new Pi’s myriad...

Did you really think the Raspberry Pi would stop getting better? At this point, we sound like a broken record, extolling on the new Pi’s myriad improvements like we’re surprised that the folks at the Raspberry Pi Foundation are continuously making their flagship board better. Still, we’ll say it again - the Raspberry Pi team have outdone themselves. The Raspberry Pi 3 Model B is out and it is AMAZING. Note: This...

$35.00

OUT OF STOCK

GPIO Stacking Header for Pi A+/B+/Pi 2/Pi 3 - Extra-long 2x20 Pins

PRODUCT ID: 2223

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins. The female header part...

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra long 10mm pins, compared with our plain version which is the same base height but has 3mm header pins instead. With 10mm you can have a HAT that has extra pins to stack another HAT on top!...

$2.50

IN STOCK

GPIO Header for Raspberry Pi A+/B+/Pi 2/Pi 3 - 2x20 Female Header

PRODUCT ID: 2222

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header. The female header part is about 8.5mm tall, good for small...

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 10mm header pins instead. With 3mm you don't have to cut the really long pins, so its ideal for basic Pi HAT design You'll get one header per...

$1.50

IN STOCK

Stacking Header for Pi A+/B+/Pi 2/Pi 3 - 2x20 Extra Tall Header

PRODUCT ID: 1979

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The...

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The female header part has extra spaces to make it 23mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. The stacky pin part is also extra-long, 10mm, so that when a standard 1.5mm thickness PCB is installed, there will be 8.5mm remaining, plenty to plug into. You'll get...

$2.95

IN STOCK

Adafruit PiRTC - PCF8523 Real Time Clock for Raspberry Pi

PRODUCT ID: 3386

This is a great battery-backed real time clock (RTC) that allows your Raspberry Pi project to keep track of time if the power is lost. Perfect for...

This is a great battery-backed real time clock (RTC) that allows your Raspberry Pi project to keep track of time if the power is lost. Perfect for data-logging, clock-building, time-stamping, timers and alarms, etc. Equipped with PCF8523 RTC, it works great with the Raspberry Pi and has native kernel support. Works perfectly with any Raspberry Pi (or similar single board linux computer) including the Pi 1, Pi 2, Pi 3, Pi Zero, A+, B+...

$5.95

IN STOCK

GPIO Header for RaspberryPi A+/B+/Pi 2/Pi 3 - Tall 2x20 Female Header

PRODUCT ID: 1992

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make...

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 10mm height instead. With 3mm you don't have to cut the really long pins, so its ideal for basic Pi plate design...

$2.95

IN STOCK

Brass M2.5 Standoffs for Pi HATs - Black Plated - Pack of 2

PRODUCT ID: 2336

"These go to eleven." 11 millimeters that is! Our Black Plated M/F Brass Standoffs are engineered specifically...

"These go to eleven." 11 millimeters that is! Our Black Plated M/F Brass Standoffs are engineered specifically to keep your Pi HAT snug on your Pi while also keeping the two boards separated, in particular the HDMI port. These standoffs can also be screwed into each other allowing stacking multiple HATs on to one Pi! They're the perfect companion for any Pi Hat combo. Each order comes with two...

$0.75

OUT OF STOCK

Break-away 0.1" 2x20-pin Strip Dual Male Header

PRODUCT ID: 2822

If we could eat headers, we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and...

If we could eat headers, we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip male header is a great way to add pins to 2x20 0.1" holes in a PCB. They're also perfect companion piece to our 2x20-pin right-angle female header.

$0.95

IN STOCK

Assembled Pi T-Cobbler Plus - GPIO Breakout - Pi A+, B+, Pi 2, Pi 3, Zero

PRODUCT ID: 2028

This is the assembled version of the Pi T-Cobbler Plus. It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2,Pi 3! (Any Pi with 2x20...

This is the assembled version of the Pi T-Cobbler Plus. It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2,Pi 3! (Any Pi with 2x20 connector) The Raspberry Pi has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all...

$7.95

IN STOCK

2x20 Socket Riser Header for Raspberry Pi HATs and Bonnets

PRODUCT ID: 4079

Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins . You can plug this into your Raspberry Pi GPIO...

Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins . You can plug this into your Raspberry Pi GPIO port and then plug a HAT or Bonnet or Phat on top. Especially useful for Bonnets that have slim headers on the bottom, but you want them to clear some of the components on the Pi, or fit into a case nicer. The header body is a standard 8.5mm. The pins are 6mm tall, so they're securely plug...

$1.95

IN STOCK

Adafruit Raspberry Pi Camera Board Case with 1/4" Tripod Mount

PRODUCT ID: 3253

This is a basic, classic Adafruit Raspberry Pi Camera Board Enclosure with a black base and a clear top. The case is as minimal as it...

This is a basic, classic Adafruit Raspberry Pi Camera Board Enclosure with a black base and a clear top. The case is as minimal as it gets, coming in just two pieces of polycarbonate that snap snugly together. This case will keep your Pi Camera safe and secure while also looking super sleek. Works with Pi Camera v1 and v2. The enclosure was designed by Mike Doell – just like our elegant, beautiful, and...

$2.95

IN STOCK

GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2/Pi 3 - (40 pins)

PRODUCT ID: 1988

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose...

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails. This cable is not compatible with the Raspberry Pi Model B or Model A! If...

$2.95

IN STOCK

Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

PRODUCT ID: 2348

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it...

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Raspberry Pi and motors are not included. Works with any and all Raspberry Pi computers with 2x20 connection port. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip ...

$22.50

48 IN STOCK

Raspberry Pi 3 Model B Starter Pack - Includes a Raspberry Pi 3

PRODUCT ID: 3058

Gotta say - this new Pi 3 is fly. All the cool kids are going to have it - but all the coolest kids are also going to have a big pack of super...

Gotta say - this new Pi 3 is fly. All the cool kids are going to have it - but all the coolest kids are also going to have a big pack of super cool accessories. We've hand chosen these accessories as the perfect accompaniment to your new Raspberry Pi 3 - Model B. It's everything you need to get going with a high quality power supply, Raspbian 8G NOOBs SD card (newly updated to work on the Pi 3), lovely case, handy...

$84.95

OUT OF STOCK

GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

PRODUCT ID: 2243

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the through-hole...

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the through-hole version of the SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header. This header is for super-slim through-hole designs. It's a custom-made, 2x20 short female header that can be used to plug a Raspberry Pi HAT onto a B+, A+, or Pi 2. It's...

$1.95

71 IN STOCK

Raspberry Pi Model B+ 512MB RAM

PRODUCT ID: 1914

OMG OMG OMG, did you hear? There's a Raspberry Pi called the Model B+ and check it out...more USB ports, more GPIO, better power supply,...

OMG OMG OMG, did you hear? There's a Raspberry Pi called the Model B+ and check it out...more USB ports, more GPIO, better power supply, four mounting holes, less sticky-out SD card! Yep, that's right, the fantastic engineers at Raspberry Pi HQ have blessed us with a new design. They've taken all the feedback over the last 3 years and rolled out a nice updated Pi with many fixes and extras...all at the same price! Take a deep...

$29.95

OUT OF STOCK

Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit

PRODUCT ID: 2345

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2 or Pi 3 with the Adafruit RGB Matrix HAT. This HAT plugs into your...

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2 or Pi 3 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. This HAT is our finest to date, full of some really great circuitry. Let me break it down for you: Simple design - plug in power, plug in...

$24.95

89 IN STOCK

Adafruit Perma-Proto HAT for Pi Mini Kit - No EEPROM

PRODUCT ID: 2310

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2 or Pi 3 (any Pi with a 2x20 connector) with this...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2 or Pi 3 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the...

$4.95

IN STOCK

Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

PRODUCT ID: 2327

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. For use...

$17.50

OUT OF STOCK

Adafruit PiRTC - Precise DS3231 Real Time Clock for Raspberry Pi

PRODUCT ID: 4282

This is the best battery-backed real time clock (RTC) you can get that allows your Raspberry Pi project to keep track of time if the power is lost....

This is the best battery-backed real time clock (RTC) you can get that allows your Raspberry Pi project to keep track of time if the power is lost. Perfect for data-logging, clock-building, NTP servers, time-stamping, timers and alarms, etc. Equipped with a genuine DS3231 RTC, it works great with the Raspberry Pi and has native kernel support. The datasheet for the DS3231 explains that this part is an "Extremely Accurate...

$14.95

46 IN STOCK

Adafruit Raspberry Pi B+ / Pi 2 / Pi 3 Case - Smoke Base - w/ Clear Top

PRODUCT ID: 2258

It took awhile to perfect - but that's okay since we can now safely say that the Adafruit case for Raspberry Pi Model B+ / Pi 2 /...

It took awhile to perfect - but that's okay since we can now safely say that the Adafruit case for Raspberry Pi Model B+ / Pi 2 / Pi 3 is The Single Greatest Raspberry Pi Model B+ Case Ever. This enclosure was designed by Mike Doell - just like our elegant, beautiful, and functional Pi Case for Raspberry Pi Model B. Made of ultra-durable, super-glossy polycarbonate, it is both good looking and tough enough...

$7.95

IN STOCK

Adafruit Pi T-Cobbler Plus Kit Breakout for 2x20 Raspberry Pi - RasPi A+, B+, Pi 2, Pi 3, Zero

PRODUCT ID: 1989

The Raspberry Pi A+/B+/Pi 2/Pi 3/Zero has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And...

The Raspberry Pi A+/B+/Pi 2/Pi 3/Zero has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Pi's 40 pins. That's why we now carry the Adafruit Pi T-Cobbler Plus Kit - Breakout + Cable for Raspberry Pi. This Cobbler...

$7.50

IN STOCK

Raspberry Pi PoE Hat

PRODUCT ID: 3953

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible with Raspberry Pi 3 B+ that has PoE pins and Raspberry Pi 4. For people with neither Pi 3 B+'s...

$20.00

IN STOCK

Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2/Pi 3 - Mini Kit

PRODUCT ID: 2324

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate...

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model Pi 3, Pi Zero, A+, B+, or Pi 2 & 3 Here's the low-down on the GPS module: -165 dBm sensitivity, 10 Hz updates, 66 channelsOnly 20mA current drawBuilt in Real Time Clock (RTC) - slot in a CR1220 backup...

$44.95

15 IN STOCK

Assembled Pi Cobbler Plus - Breakout Cable - for Pi B+/A+/Pi 2/Pi 3/Pi 4

PRODUCT ID: 2029

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY...

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s / Pi 2's / Pi 3 / Pi 4's 40 pins. That's why we now carry the Adafruit Assembled Pi...

$6.95

IN STOCK

SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

PRODUCT ID: 2187

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's...

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's harder to use than the Thru-Hole type headers, but for the slickest, slimmest fit, this header is recommended!

$1.95

4 IN STOCK

Adafruit PiTFT 2.2" HAT Mini Kit - 320x240 2.2" TFT - No Touch

PRODUCT ID: 2315

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240...

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top of your Model A+ or B+ and fits into our case quite nicely. It's designed to plug directly onto the...

$24.95

61 IN STOCK

Brass M2.5 Standoffs 16mm tall - Black Plated - Pack of 2

PRODUCT ID: 2337

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered...

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories with extra tall headers properly secured while also keeping the two boards separated. These standoffs can also be screwed into each other just like the 11mm versions (made for PiHATs). Each order comes with two standoffs and two hex...

$1.25

IN STOCK

SmartiPi Touch 2 - Stand for Raspberry Pi 7" Touchscreen Display - Compatible with Pi 4

PRODUCT ID: 4377

Here is an updated, excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say...

Here is an updated, excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to the improved SmartiPi Touch 2 which has a ton of new goodies like Pi 4 compatibility, various front-pieces for adding LEGO brick compatibility, and even a fan and mount! The 7" Display is secured into the case with four screws, and your Raspberry Pi is enclosed in a compartment on...

$27.99

43 IN STOCK

IDC Breakout Helper - 2x20 (40 pin)

PRODUCT ID: 2270

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular...

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2 (40 pins). It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so...

$2.25

IN STOCK

Adafruit GPIO Reference Card for Raspberry Pi Model B+/Pi 2/Pi 3

PRODUCT ID: 2263

This board makes connecting wires to the Raspberry Pi GPIO incredibly easy. It's a reference board that makes it really easy to see if...

This board makes connecting wires to the Raspberry Pi GPIO incredibly easy. It's a reference board that makes it really easy to see if you're connecting your wires correctly. We liked the Pi GPIO Reference Board from Low Voltage Labs so much that we worked with them to license their design! We made some changes to the Low Voltage version - including grouping the pins into categories like I2C, IO, UART, SPI, and power....

$2.50

IN STOCK

Pimoroni Pico HAT Hacker

PRODUCT ID: 3577

Pimoroni's Pico HAT Hacker gives you full access to all 40 pins on your Pi, broken out at the top. It's a super-skinny 0.8mm PCB, so you can...

Pimoroni's Pico HAT Hacker gives you full access to all 40 pins on your Pi, broken out at the top. It's a super-skinny 0.8mm PCB, so you can solder it right onto the pins on your Pi and still have enough height on a standard header to fit a HAT or pHAT on top. There are handy labels for all of the pins, with BCM pin numbering on one side, and more descriptive labels on the other to show where the I2C, UART, SPI, PWM, and I2S pins...

$2.50

IN STOCK

0.1" 2x20-pin Strip Right Angle Female Header

PRODUCT ID: 2823

If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and...

If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip, right-angle female header is a perfect companion piece to our 2x20-pin Dual Male Header. It's a great way to add right-angle capability to a 2x20 pin circuit board either by attaching the right-angle male headers to the board and having a right-angle female...

$1.50

IN STOCK

2x20 pin IDC Box Header - Raspberry Pi A+/B+/Pi 2/Pi 3

PRODUCT ID: 1993

This handy 2x20 IDC Box Header is the matching connector for our 40-pin GPIO Cable. By soldering this onto perf board you can run a GPIO cable from...

This handy 2x20 IDC Box Header is the matching connector for our 40-pin GPIO Cable. By soldering this onto perf board you can run a GPIO cable from your Pi A+/B+/Pi 2/Pi 3 to the socket. This is the same socket that comes with our Pi Cobbler Plus or Pi T-Cobbler Plus but without the PCBs or anything This socket only works for the Raspberry Pi Model A+/B+/Pi 2/Pi 3 GPIO cables. It does not work with the Raspberry Pi Model B GPIO...

$0.75

OUT OF STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Orange

PRODUCT ID: 2250

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your favorite sports team, or even...

$5.00

IN STOCK

Raspberry Pi 3 Model B Starter Pack (Without Raspberry Pi)

PRODUCT ID: 3241

Gotta say - this new Pi 3 is fly. All the cool kids are going to have it - but all the coolest kids are also going to have a big pack of super...

$49.95

33 IN STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Clear

PRODUCT ID: 2253

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Ever - we decided to make it even better by adding ...

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your favorite sports team, or...

$5.00

IN STOCK

Adafruit Capacitive Touch HAT for Raspberry Pi - Mini Kit - MPR121

PRODUCT ID: 2340

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing...

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like touch-reactive tablets and phones, as well as control panels for appliances, which is where you may have used it before. This HAT allows you to create electronics that can...

$14.95

72 IN STOCK

Adafruit PiTFT 2.4" HAT Mini Kit - 320x240 TFT Touchscreen

PRODUCT ID: 2455

Is this not the cutest little display for the Raspberry Pi? It features a 2.4" display with 320x240 16-bit color pixels and a resistive touch...

Is this not the cutest little display for the Raspberry Pi? It features a 2.4" display with 320x240 16-bit color pixels and a resistive touch overlay. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! It's designed to fit nicely onto the Pi Model Zero, A+, B+, Pi 2, Pi 3 - any Pi with a 2x20 connector. This...

$34.95

11 IN STOCK

Adafruit DC & Stepper Motor Bonnet for Raspberry Pi

PRODUCT ID: 4280

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as...

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. We basically took our super-popular DC+Stepper Motor HAT and squeezed it down and made it fully assembled - plug and play ready to go, no soldering required! Raspberry Pi and motors are not included. Works with any and all...

$22.50

30 IN STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Smoke Gray

PRODUCT ID: 2256

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Ever - we decided to make it even better by adding ...

$5.00

IN STOCK

Pi-EzConnect Terminal Block Breakout HAT

PRODUCT ID: 2711

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has...

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry PiMini proto area for adding componentsAdd standard male or female headers for breadboard like functionalityPower (both 5V and 3.3V) as well as ground connections...

$19.95

78 IN STOCK

Downgrade GPIO Ribbon Cable for Pi A+/B+/Pi 2/Pi 3 - 40p to 26p

PRODUCT ID: 1986

Oof - you got a Raspberry Pi Model A+ or B+ that you want to have work with some old kit or plate or breakout or something and it uses the classic...

Oof - you got a Raspberry Pi Model A+ or B+ that you want to have work with some old kit or plate or breakout or something and it uses the classic 26-pinout. Very frustrating, it is...unless you have this ingenious 'downgrade' GPIO cable. It has a 40-pin socket on one end, but only the first 26 pins have a cable and the other end matches any sort of Cobbler or PermaPi or what-have-you. Cable is 6" long, and pin #1 is marked with a...

$2.95

3 IN STOCK

Raspberry Pi Sense HAT - For the Pi 3 / 2 / B+ / A+

PRODUCT ID: 2738

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT ! The Raspberry Pi Sense HAT is...

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT ! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘Astro Pi’. The Sense HAT has several integrated circuit based sensors can be used for many different types of experiments, applications, and even games. And it's being used in conjunction with the Raspberry Pi Foundation...

$39.95

IN STOCK

Pimoroni Raspberry Pi 7" Touchscreen Display Case - Noir

PRODUCT ID: 2033

Noir is the new black! With this Noir Raspberry Pi 7" Touchscreen Display Case you can protect your lovely Pi Foundation...

Noir is the new black! With this Noir Raspberry Pi 7" Touchscreen Display Case you can protect your lovely Pi Foundation PiTFT - 7" Touchscreen Display for Raspberry Pi! Three unique layers provide support and protection to the back of the display, leaving your touchscreen entirely unimpeded and all Raspberry Pi ports totally accessible. This case is also constructed with 2 sturdy legs to hold your...

$14.95

44 IN STOCK

Stacking Header for Raspberry Pi - 2x13 Extra Tall

PRODUCT ID: 1112

Stack multiple plates, breakouts etc onto your Raspberry Pi with this custom-made extra-tall and extra-long 2x13 female header. The female header...

Stack multiple plates, breakouts etc onto your Raspberry Pi with this custom-made extra-tall and extra-long 2x13 female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. The stacky pin part is also extra-long, 9.7mm, so that when a standard 1.5mm thickness PCB is installed, there will be 8mm remaining, plenty to plug into. You'll get one header per...

$1.95

IN STOCK

Adafruit Perma-Proto 40-Pin Raspberry Pi Breadboard PCB Kit - with 2x20 Header

PRODUCT ID: 4354

We put a PermaProto full-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi!...

We put a PermaProto full-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4,...

$7.95

IN STOCK

Adafruit DPI TFT Kippah for Raspberry Pi

PRODUCT ID: 2454

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit ! This...

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit ! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what normally would go out the HDMI port come up on a nice little flat screen. * Its not technically a HAT due to the lack of an on-board EEPROM, but its the...

$13.95

27 IN STOCK

Adafruit Perma-Proto HAT for Pi Mini Kit - With EEPROM

PRODUCT ID: 2314

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with which...

$7.50

18 IN STOCK

Pimoroni Automation HAT for Raspberry Pi

PRODUCT ID: 3289

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Take control of and...

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Take control of and monitor your world with Pimoroni's Automation HAT -- an ultimate jack-of-all-trades Raspberry Pi HAT! With relays, analog channels, powered outputs, and buffered inputs (all 24V tolerant), this home monitoring and automation controller allows you to hook up a plethora of goodies to...

$29.95

7 IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Smoke Gray

PRODUCT ID: 2244

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Clear

PRODUCT ID: 2257

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Ever - we decided to make it even better by adding ...

$3.00

IN STOCK

Faceplate and Buttons Pack for 2.8" PiTFTs - Raspberry Pi B+ / Pi 2

PRODUCT ID: 2807

Complete your Pi setup with our custom designed faceplate specifically designed to fit your 2.8" PiTFT and Adafruit Pi B+ / Pi 2 case base!...

Complete your Pi setup with our custom designed faceplate specifically designed to fit your 2.8" PiTFT and Adafruit Pi B+ / Pi 2 case base! This Faceplate and Buttons Pack is a simple way to enclose your 2.8" PiTFT and Pi safely and in style. The faceplate replaces the normal 'top' of an Adafruit Pi case, with a sleek black bezel and button pads. This pack works with the Raspberry Pi Model B+ / Pi 2 / Pi 3, and...

$4.95

IN STOCK

Microsoft IoT Pack for Raspberry Pi 3 - w/ Raspberry Pi 3

PRODUCT ID: 2733

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an...

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an IoT enabled device. A collaboration between Microsoft's IoT division and Adafruit, this pack's the best way to get started using both Windows 10 on your Pi and to start doing some popular projects with the internet of things. Check...

$114.95

OUT OF STOCK

Pimoroni Pan-Tilt HAT for Raspberry Pi - without pan-tilt module

PRODUCT ID: 3353

The Pan-Tilt HAT from Pimoroni lets you mount and control a pan-tilt module right on top of your Raspberry Pi. The HAT and its on-board...

The Pan-Tilt HAT from Pimoroni lets you mount and control a pan-tilt module right on top of your Raspberry Pi. The HAT and its on-board microcontroller let you independently drive the two servos (pan and tilt), as well as driving up to 24 regular LED (with PWM control) or NeoPixel RGB (or RGBW) LEDs. There's also a handy slot through which you can route the servo, LED, and camera cables. The module pans and tilts through 180...

$14.95

8 IN STOCK

Microsoft IoT Pack for Raspberry Pi 3 - No Pi

PRODUCT ID: 2702

The Microsoft Internet of Things Pack for Raspberry Pi 3 is the best way to get started using Windows 10 and your Raspberry Pi as an IoT...

$75.00

46 IN STOCK

Adafruit Perma-Proto 40-Pin Raspberry Pi Half-Size PCB Kit - with 2x20 Header

PRODUCT ID: 4353

We put a PermaProto half-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi!...

We put a PermaProto half-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the 40-Pin PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with extra prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4,...

$5.95

54 IN STOCK

Adafruit DPI TFT Kippah for Raspberry Pi with Touch Support

PRODUCT ID: 2453

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit ! This...

$19.95

8 IN STOCK

Pi Foundation Raspberry Pi B+ / Pi 2 / Pi 3 Case

PRODUCT ID: 2604

The first 'official' case from the Raspberry Pi Foundation is here in Raspberry Pi's sleek pink and white! While we've had our...

The first 'official' case from the Raspberry Pi Foundation is here in Raspberry Pi's sleek pink and white! While we've had our own set of cases for awhile now, the Pi foundation's first foray into the case world is an impressive, well-designed effort and definitely what we've come to expect from the folks who made the Raspberry Pi. The case comes in five parts so you can snap in sides or tops according to how...

$9.95

IN STOCK

Pimoroni pHAT Stack for Raspberry Pi

PRODUCT ID: 3742

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's pHAT Stack! This...

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's pHAT Stack! This expansive breakout PCB offers 6 sets of 2x20 pin headers - one for connecting to your Pi and the other 5 for a plethora of HATs, pHATs or bonnets. The combinations are endless... It's perfect for your projects, displaying temperatures, times, etc. and becomes really useful when combined...

$16.95

36 IN STOCK

SmartiPi Touch 2 Back Cover (For SmartiPi 2 Only) - Large 35mm

PRODUCT ID: 4378

Need a smart solution for covering the back of your SmartiPi Touch display stand? This simple cover from SmartiPi screws into the back VESA...

Need a smart solution for covering the back of your SmartiPi Touch display stand? This simple cover from SmartiPi screws into the back VESA mounts on the SmartiPi Touch with the four included screws. It allows you to protect HAT boards and other electronic components that you might want for your project. It's made of ABS plastic and will have to be cut, drilled, or modified for your application. The case also helps protect the...

$7.99

32 IN STOCK

Adafruit Pi Protector for Raspberry Pi Model B+ / Pi 2 / Pi 3 B+

PRODUCT ID: 2292

You've seen the A+ pocket protector - cometh the hour for the full size Pi version. Introducing PaintYourDragon's last-cut masterpiece part...

You've seen the A+ pocket protector - cometh the hour for the full size Pi version. Introducing PaintYourDragon's last-cut masterpiece part ii: Adafruit Pi Protector for Raspberry Pi ! It's not quite a full case, however it will keep your Pi B+ safe and svelte. Keep your Raspberry Pi computer tidy and safe in this lovely clear acrylic enclosure. We designed this simple protector to be beautiful, easy to assemble...

$7.50

81 IN STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Blue

PRODUCT ID: 2252

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / 3 Case Ever - we decided to make it even better by adding ...

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / 3 Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your favorite sports team, or...

$5.00

IN STOCK

Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB Kit

PRODUCT ID: 1171

We put a PermaProto quarter-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It...

We put a PermaProto quarter-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always...

$4.95

IN STOCK

Adafruit Pi Box Plus - Enclosure for RasPi Model B+/Pi 2/ Pi 3

PRODUCT ID: 1985

PaintYourDragon is back with another gorgeous laser-cut masterpiece. This time he's taken a pass at updating the classic Adafruit Pi Box for...

PaintYourDragon is back with another gorgeous laser-cut masterpiece. This time he's taken a pass at updating the classic Adafruit Pi Box for the Raspberry Pi Model B+ / Pi 2 / Pi 3 Model B and Pi 3 Model B+ only. Keep your Raspberry Pi® Model B+ computer safe and sound in this lovely clear acrylic enclosure. We designed this case to be beautiful, easy to assemble and perfect for any use (but especially for those who...

$12.50

87 IN STOCK

8 Channel LoRa Gateway HAT with LoRa and GPS Antenna - SX1301 - Pi Not Included

PRODUCT ID: 4284

If you're building a Raspberry Pi project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most...

If you're building a Raspberry Pi project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most cases. However , WiFi does not have a long range and also requires both investment (through your ISP) and setup (routers, access points, network security schemes). If you're deploying your project somewhere more remotely, without WiFi or a strong cellular network, like a rural area, you'll...

$149.95

58 IN STOCK

SmartiPi Touch 2 Back Cover (For SmartiPi 2 Only) - Small 15mm

PRODUCT ID: 4379

Need a smart solution for covering the back of your SmartiPi Touch 2 display stand? This simple cover from SmartPi screws into the back VESA...

Need a smart solution for covering the back of your SmartiPi Touch 2 display stand? This simple cover from SmartPi screws into the back VESA mounts on the SmartiPi Touch 2 with the four included screws. It allows you to protect HAT boards and other electronic components that you might want for your project. It's made of ABS plastic and will have to be cut, drilled, or modified for your application. The case also helps protect the...

$7.99

35 IN STOCK

Pimoroni Explorer HAT Pro for Raspberry Pi

PRODUCT ID: 2427

The Explorer HAT Pro is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer Pro from Pimoroni there are a heap of...

The Explorer HAT Pro is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer Pro from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features : 4x buffered 5V tolerant inputs Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V...

$22.95

66 IN STOCK

Pibow Coupé - Enclosure for Raspberry Pi 2 / B+ / Pi 3 / Pi 3 B

PRODUCT ID: 2083

"Whoa! Is that a credit-card sized computer inside a sleek, hot-chili red body?" they'll all be saying, head's turned toward...

"Whoa! Is that a credit-card sized computer inside a sleek, hot-chili red body?" they'll all be saying, head's turned toward your Raspberry Pi. "It looks so fast," they'll remark admiringly. "It's like a sports car for your Pi!" Humbly, you'll reply, "Oh that? It's just the Pibow Coupé - the brand new case from the folks at Pimoroni!" This fast looking Coupe...

$11.95

15 IN STOCK

PiTFT Pibow+ Kit for Pi 2 / B+ / Pi 3 B+

PRODUCT ID: 2779

What's better than our 2.8" 320x240 and 3.5" 480x320 PiTFT Pluses? How about a custom-designed enclosure for said PiTFTs, in a...

What's better than our 2.8" 320x240 and 3.5" 480x320 PiTFT Pluses? How about a custom-designed enclosure for said PiTFTs, in a handsome midnight-blue? Crafted out of eleven unique layers, each laser-cut from colourful high-quality cast acrylic and once stacked they securely contain a Raspberry Pi 2, Model B+, Pi 3, or Pi 3 B+ while leaving the primary ports accessible. Weighing only 92 grams the case is...

$19.95

23 IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Blue

PRODUCT ID: 2248

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

IN STOCK

Pimoroni Mini Black HAT Hack3r - Fully Assembled

PRODUCT ID: 3182

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT or pHAT on your...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT or pHAT on your Raspberry Pi Model Zero, 3, 2, A+, or B+ (any Pi with a 2x20 connector). The Pimoroni Mini Black HAT Hack3r is ideal for debugging your (p)HAT projects or combining a (p)HAT with other circuits. Features: HAT & pHAT spec landing area with PCB standoffsIncludes 40 pin GPIO ribbon cableAll GPIO pins...

$14.95

63 IN STOCK

Raspberry Pi Arcade Cabinet Pack

PRODUCT ID: 3272

Couldn't get one of those Nintendo Mini Classic consoles? No problem, we've got you covered with this no-solder no-tools required kit! Video...

Couldn't get one of those Nintendo Mini Classic consoles? No problem, we've got you covered with this no-solder no-tools required kit! Video games are one of the most popular applications for the Raspberry Pi (and one of the best gifts to get over the holidays). Play NES, Sega, MAME, SNES, Atari and more! Thanks to the easy-to-use Raspberry Pi and some clever software, you can recreate the classic arcade experience at home. Adafruit will...

$59.95

13 IN STOCK

Raspberry Pi Media Center Kit - Includes Pi Model 3 B+

PRODUCT ID: 3158

Have you always wanted to binge-watch Battlestar Galactica on a single-board computer? We have - and that's why we put together this...

Have you always wanted to binge-watch Battlestar Galactica on a single-board computer? We have - and that's why we put together this Raspberry Pi Media Center kit for Raspberry Pi! Based around the OSMC media center, this kit includes everything you need to get going on building your own Raspberry Pi media center. OSMC is a free and open source media center that's built for the people, by the people. It's really...

$99.95

1 IN STOCK

ARM-based IoT Kit for Cloud IoT Core - No Pi

PRODUCT ID: 3593

The Arm-based Internet of Things Pack for Raspberry Pi 3 is another great addition to our family of IoT packs. If you want to start using...

The Arm-based Internet of Things Pack for Raspberry Pi 3 is another great addition to our family of IoT packs. If you want to start using your Raspberry Pi as an IoT-enabled device, then this kit is for you. You might not know it, but Arm-based chips are everywhere . From mobile devices to supercomputer, from medical instruments to agricultural sensors, and from base stations to servers; Arm technologies each 80% of the global...

$74.95

11 IN STOCK

Pimoroni Picade X HAT USB-C for Raspberry Pi - PIM462

PRODUCT ID: 3402

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT . It's the best, easiest way to make a...

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT . It's the best, easiest way to make a super-sweet arcade system using any Raspberry Pi. Simply pop it onto your Pi, plug your Pi power supply into the USB-C connector on the Picade HAT (it back-powers your Pi through the GPIO, so no need for a separate power supply), wire up your controls to the terminal blocks,...

$19.95

25 IN STOCK

Pimoroni Unicorn Hat - 8x8 RGB LED Shield for Raspberry Pi A+/B+

PRODUCT ID: 2288

Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi....

Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi. Unicorn HAT provides a wash of controllable color that is ideal for mood-lighting, 8x8 pixel art, persistence of vision effects, status indications, or just blasting colour into your surroundings. 64 RGB LEDs (WS2812B) each wtih 24-bit RGB colorPython API (NeoPixel compatible!)EEPROM with...

$29.95

4 IN STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Red

PRODUCT ID: 2334

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$5.00

IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Orange

PRODUCT ID: 2246

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Red

PRODUCT ID: 2335

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

49 IN STOCK

Element14 Desktop Enclosure Kit for Raspberry Pi Computers

PRODUCT ID: 4131

Element14's Pi Desktop Enclosure Kit gives you the gear to convert your Raspberry Pi into a mini desktop computer! The sleek, minimal enclosure...

Element14's Pi Desktop Enclosure Kit gives you the gear to convert your Raspberry Pi into a mini desktop computer! The sleek, minimal enclosure is designed with an expansion controller that plugs into your Pi to give it all the extras you've been missing. It comes intelligent on/off power switch and RTC. It even has an mSATA SSD socket and controller so you can plug in a large storage drive to create a media center or network storage...

$49.95

21 IN STOCK

Computer Add-On Pack for Raspberry Pi

PRODUCT ID: 2129

Turn your Raspberry Pi into a real computer with this computer add-on pack! Look, we're not advocating that you throw out your Macbook Pro....

Turn your Raspberry Pi into a real computer with this computer add-on pack! Look, we're not advocating that you throw out your Macbook Pro. But we do think it's really cool that, with just a few accessories, you can convert your credit-card sized computer into a grown up pocket computer. We don't include a monitor but do include an HDMI cable so you can connect it to whatever you have on-hand OR you can pick up one of our...

$22.95

IN STOCK

Pimoroni Unicorn HAT HD

PRODUCT ID: 3580

Unicorn HAT HD crams 256 RGB LEDs, in a 16x16 = 256 LED matrix, onto a single HAT. High-definition rainbow goodness! You can still use it for all of...

Unicorn HAT HD crams 256 RGB LEDs, in a 16x16 = 256 LED matrix, onto a single HAT. High-definition rainbow goodness! You can still use it for all of the same things as the regular Unicorn HAT, but with four times as many pixels it makes much more complex animations possible, including scrolling text, and even low resolution videos. The bundled ninja diffuser makes the pixels look extra shiny by providing some subtle diffusion, blurring the...

$34.95

27 IN STOCK

Pimoroni Skywriter HAT - 3D Gesture Sensor for Raspberry Pi

PRODUCT ID: 2325

Control your Raspberry Pi 3, 2, A+, B+, or Zero with a flick of the wrist! The Pimoroni Skywriter HAT senses the position...

Control your Raspberry Pi 3, 2, A+, B+, or Zero with a flick of the wrist! The Pimoroni Skywriter HAT senses the position of your fingers in the air above. Using Pimoroni's Python API you can read off the positional data (x, y, z) and common gestures like flick left, tap, and double tap. Electrical near-field 3D/gesture sensing4-layer PCB for best sensing performanceSenses from up to 5cm awayFull 3D position data...

$20.95

58 IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Purple

PRODUCT ID: 2303

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

59 IN STOCK

Faceplate and Buttons Pack for 2.4" PiTFT HAT - Raspberry Pi A+

PRODUCT ID: 2808

Complete your Pi setup with our custom designed faceplate specifically designed to fit your 2.4" PiTFT HAT and Adafruit Pi A+ case...

Complete your Pi setup with our custom designed faceplate specifically designed to fit your 2.4" PiTFT HAT and Adafruit Pi A+ case base! This Faceplate and Buttons Pack is a simple way to enclose your 2.4" PiTFT and Pi safely and in style. The faceplate replaces the normal 'top' of an Adafruit Pi case, with a sleek black bezel and button pads. This pack works with the Raspberry Pi Model A+, and 2.4" PiTFT...

$4.95

IN STOCK

Pimoroni Rainbow HAT for Android Things™ and Raspberry Pi

PRODUCT ID: 3354

The Rainbow HAT from Pimoroni has a buffet of sensors, inputs, and displays to explore Android Things™. Use it as a weather station, a clock, a...

The Rainbow HAT from Pimoroni has a buffet of sensors, inputs, and displays to explore Android Things™. Use it as a weather station, a clock, a timer or stopwatch, a mood light, or endless other things. Pimoroni collaborated with the Android Things™ team at Google to create this great add-on board that features displays, sensors, sound, and lots of LEDs! It's the perfect introduction to developing Android Things applications on...

$24.95

IN STOCK

Raspberry Pi Media Center Kit for Raspberry Pi3 - No Pi Included

PRODUCT ID: 3114

Have you always wanted to binge-watch Battlestar Galactica on a single-board computer? We have! And that's why we put together this...

Have you always wanted to binge-watch Battlestar Galactica on a single-board computer? We have! And that's why we put together this Raspberry Pi Media Center kit for Raspberry Pi Model 3's! Based around the OSMC media center, this kit includes everything you need to get going on building your own Raspberry Pi media center. OSMC is a free and open source media center that's built for the people, by the people....

$64.95

1 IN STOCK

Pimoroni Piano HAT

PRODUCT ID: 2695

Raspberry Pi - meet your new musical B.F.F! With the Pimoroni Piano HAT you can control hardware synthesizers and software...

Raspberry Pi - meet your new musical B.F.F! With the Pimoroni Piano HAT you can control hardware synthesizers and software synths or play some really beautiful music in Python. Surprise everyone with your creativity, maybe even yourself! This HAT comes with 16 touch sensitive buttons, up and down octave controls, and 13 piano keys from C to shining C! Each button on Piano HAT can be...

$19.95

11 IN STOCK

Raspberry Pi DIY Camera Pack

PRODUCT ID: 3275

If the holidays promise anything, it’s almost certainly a deluge of photographs. Instead of taking out your smartphones, why not build your own...

If the holidays promise anything, it’s almost certainly a deluge of photographs. Instead of taking out your smartphones, why not build your own camera? With one of Adafruit’s best selling screens and an official Raspberry Pi camera, you’ll be ready to set up your very own digital camera in no time at all. You’ll be immortalizing all those great memories and get to show off your maker skills in the process. The included...

$89.95

9 IN STOCK

ARM-based IoT Kit for Cloud IoT Core - w/ Raspberry Pi 3

PRODUCT ID: 3594

The Arm-based Internet of Things Pack for Raspberry Pi 3 is another great addition to our family of IoT packs. If you want to start using...

$114.95

OUT OF STOCK

Ninja Pibow - Enclosure for Raspberry Pi Model B+ / Pi 2 / Pi 3

PRODUCT ID: 2081

Clad your Pi in Ninja Black with this Pibow Enclosure for the Raspberry Pi 2, Pi 3 Model B, or RaspberryPi 1 Model B+! The Ninja Pibow is a night...

Clad your Pi in Ninja Black with this Pibow Enclosure for the Raspberry Pi 2, Pi 3 Model B, or RaspberryPi 1 Model B+! The Ninja Pibow is a night black case for your Raspberry Pi computer. It's crafted out of high quality acrylic layers with a transparent top and base. It's smooth, slick, and durable and because of its black color, blends surreptitiously into any room. You simply stack the layers around...

$17.95

12 IN STOCK

Timber Pibow - Enclosure for Raspberry Pi Model B+ Computers

PRODUCT ID: 2082

Clad your B+ in elegant wood with this Pibow Enclosure for the Raspberry Pi! The Timber Pibow is a spruce-cut case for your Raspberry Pi...

Clad your B+ in elegant wood with this Pibow Enclosure for the Raspberry Pi! The Timber Pibow is a spruce-cut case for your Raspberry Pi computer. It' s crafted out of high quality wood with a transparent top and base. It's smooth, slick, and durable and because of its wood finish, matches your kitchen table, hardwood, floors, or plant-lined living room. You simply stack the layers around your Raspberry Pi...

$22.50

75 IN STOCK

Raspberry Pi 2 or Model B+ Starter Pack (Without Raspberry Pi)

PRODUCT ID: 2126

You're going to work hard with your Raspberry Pi 2 Model B or Raspberry Pi 1 Model B+. You're going to have to solder, code, and Linux...

You're going to work hard with your Raspberry Pi 2 Model B or Raspberry Pi 1 Model B+. You're going to have to solder, code, and Linux your Maker heart out. That's why we've tried to make it as easy as possible to start - by combining the Raspberry Pi with what we think are the best beginners' Pi accessories into one easy to use kit. We've hand chosen these accessories as the perfect accompaniment to your...

$59.95

33 IN STOCK

Computer Starter Kit for Raspberry Pi 3 (Pi Not Included)

PRODUCT ID: 1805

Want to create your own computer but unsure of where to start? Our Computer Kit for Raspberry Pi might be just the thing you need to get your gears...

Want to create your own computer but unsure of where to start? Our Computer Kit for Raspberry Pi might be just the thing you need to get your gears in motion! This kit provides you with a keyboard, mouse, power supply, Pi enclosure, HDMI cable, and an SD card with the necessary operating system out of which you can operate. The creation of your computer begins here! Kit includes: 1 x HDMI Cable - 1 meter1 x 16GB Card with NOOBS...

$50.00

IN STOCK

Computer Starter Kit for Raspberry Pi 3 (Includes Raspberry Pi!)

PRODUCT ID: 1806

Want to create your own computer but unsure of where to start? Our Computer Kit for Raspberry Pi 3 might be just the thing you need to get your gears...

Want to create your own computer but unsure of where to start? Our Computer Kit for Raspberry Pi 3 might be just the thing you need to get your gears in motion! This kit provides you with a keyboard, mouse, power supply, Pi enclosure, HDMI cable, and an SD card with the necessary operating system out of which you can operate. The creation of your computer begins here! Kit includes: 1 x HDMI Cable - 1 meter1 x 8GB MicroSD Card with...

$84.95

OUT OF STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Various Colors

PRODUCT ID: 2285

Now that we have The Single Greatest Raspberry Pi Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match...

Now that we have The Single Greatest Raspberry Pi Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+, Pi 2's or Pi 3's case based on your mood, your favorite sports...

1 IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Various Colors

PRODUCT ID: 2286

Now that we have The Single Greatest Raspberry Pi Model B+ Case Ever - we decided to make it even better by adding COLORS!!!!! Mix...

Now that we have The Single Greatest Raspberry Pi Model B+ Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your favorite sports team, or even your...

1 IN STOCK

Raspberry Pi 3 Model B Starter Pack

PRODUCT ID: 3334

Gotta say - this new Pi 3 is fly. All the cool kids are going to have it - but all the coolest kids are also going to have a big pack of super...

1 IN STOCK

ARM-based IoT Kit for Cloud IoT Core

PRODUCT ID: 3609

The Arm-based Internet of Things Pack for Raspberry Pi 3 is another great addition to our family of IoT packs. If you want to start using...

1 IN STOCK

Adafruit Half-size Perma-Proto Raspberry Pi Breadboard PCB Kit

PRODUCT ID: 1148

We put a PermaProto half sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has...

We put a PermaProto half sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always...

$5.95

10 IN STOCK

Adafruit Perma-Proto Raspberry Pi Breadboard PCB Kit

PRODUCT ID: 1135

We put a PermaProto full sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has...

We put a PermaProto full sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x13 connectors such as the Pi 1 Model B! We also stock a...

$7.95

30 IN STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Yellow

PRODUCT ID: 2249

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$5.00

IN STOCK

SmartiPi Touch Back Cover - Small

PRODUCT ID: 3569

Need a smart solution for covering the back of your SmartiPi Touch display stand? This simple cover from SmartPi screws into the back VESA...

Need a smart solution for covering the back of your SmartiPi Touch display stand? This simple cover from SmartPi screws into the back VESA mounts on the SmartiPi Touch with the four included screws. It allows you to protect HAT boards and other electronic components that you might want for your project. It's made of ABS plastic and will have to be cut, drilled, or modified for your application. The case also helps protect the...

$9.95

59 IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Green

PRODUCT ID: 2254

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

41 IN STOCK

Pi Model B+ / Pi 2 / Pi 3 Case Base - Pink

PRODUCT ID: 2255

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$5.00

IN STOCK

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Yellow

PRODUCT ID: 2245

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

$3.00

58 IN STOCK

SmartiPi Touch - Stand for Raspberry Pi 7" Touchscreen Display

PRODUCT ID: 3187

Here is an excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to...

Here is an excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to the SmartiPi Touch . The 7" Display is secured into the case with four screws and the Raspberry Pi is enclosed in the compartment on the back of the case. A simple door covers the Pi in the compartment allowing for the display ribbon cable to connect to the Raspberry Pi DSI port. You can...

DISCONTINUED

SmartiPi Touch Stand with Lego Compatible Front

PRODUCT ID: 3576

Here is an excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to...

Here is an excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to the SmartiPi Touch with Lego Compatible Front – the Lego-friendly version of the standard SmartiPi Touch. The 7" Display is secured into the case with four screws and the Raspberry Pi is enclosed in the compartment on the back of the case. A...

DISCONTINUED

SmartiPi Touch Back Cover - Large

PRODUCT ID: 3570

Need a smart solution for covering the back of your SmartiPi Touch display stand? This simple cover from SmartiPi screws into the back VESA...

DISCONTINUED

Rainbow Pibow - Enclosure for Raspberry Pi 2 / Model B+/ Pi 3

PRODUCT ID: 2084

Clad your B+ in the colors of the rainbow with this Pibow Enclosure for the Raspberry Pi 2, Pi 3 Model B, or RaspberryPi 1 Model B+ and...

Clad your B+ in the colors of the rainbow with this Pibow Enclosure for the Raspberry Pi 2, Pi 3 Model B, or RaspberryPi 1 Model B+ and RaspberryPi 3 Model B+! The Rainbow Pibow is a colorful case for your Raspberry Pi computer. It's crafted out of high quality acrylic layers with a transparent top and base. It's smooth, slick, and durable and because of its multi-color finish, stands out in almost any...

DISCONTINUED

Anidees Black Case w/ Smokey Top for Raspberry Pi B+/Pi 2/Pi 3

PRODUCT ID: 2347

Now that you have your Raspberry Pi Model B+ Pi 2 or Pi 3- it's a good idea to protect it. And while our beautifully...

Now that you have your Raspberry Pi Model B+ Pi 2 or Pi 3- it's a good idea to protect it. And while our beautifully designed B+ / Pi 2 Case is great for showing off your Pi, you might want an enclosure that's a bit more luxurious. Luckily, there's the Raspberry Pi B+ / Pi 2 / Pi 3 - Unibody Black Case with Smokey Top by Anidees. While it works with a Pi 3, the metal case may attenuate the built...

DISCONTINUED

Raspberry Pi 1 Model B+ Starter Pack - Includes a Raspberry Pi 1

PRODUCT ID: 2125

You're going to work hard with your Raspberry Pi B+. You're going to have to solder, code, and Linux your Maker heart out....

You're going to work hard with your Raspberry Pi B+. You're going to have to solder, code, and Linux your Maker heart out. That's why we've tried to make it as easy as possible to start - by combining the Raspberry Pi B+ with what we think are the best beginners' Pi B+ accessories into one easy to use kit. We've hand chosen these accessories as the perfect accompaniment to your new Raspberry Pi Model B+....

DISCONTINUED

CODER Pack for Raspberry Pi 2 Model B

PRODUCT ID: 1538

Coder is a free, open source project from Google that turns a Raspberry Pi 2 model B into a simple platform that educators and parents can use to...

Coder is a free, open source project from Google that turns a Raspberry Pi 2 model B into a simple platform that educators and parents can use to teach the basics of building for the web. New coders can craft small projects in HTML, CSS, and Javascript, right from the web browser. This pack has all you need to get started! As of Feb 9, 2015, this pack comes with the Raspberry Pi 2 model B and Coder v8! Each order comes with: Raspberry Pi 2...

DISCONTINUED

Pimoroni Black HAT Hack3r Kit

PRODUCT ID: 2339

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT on your Raspberry Pi...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT on your Raspberry Pi Model Pi 3, 2, A+, or B+. The Pimoroni Black HAT Hack3r is ideal for debugging your HAT projects or combining a HAT with other circuits. Features: HAT spec landing area with PCB standoffsIncludes 40 pin GPIO ribbon cableAll GPIO pins labelled with function, BCM pin number, physical pin numberRubber...

DISCONTINUED

SmartiPi - Building Block Compatible Case - Raspberry Pi B+ Pi2 - Gray

PRODUCT ID: 2447

Now that you have your Raspberry Pi Model B+ or Pi 2 - it's a good idea to protect it. And while our beautifully designed...

Now that you have your Raspberry Pi Model B+ or Pi 2 - it's a good idea to protect it. And while our beautifully designed B+ / Pi 2 Case is great for showing off your Pi, you might want an enclosure that's a bit more versatile. Luckily, there's the SmartiPi Kit - Removable building block such as LEGO® compatible case for Raspberry Pi B+ / Pi 2 by Smarticase! This case comes in a basic two piece...

DISCONTINUED

AstroBox pack - Includes Raspberry Pi 2, Model B

PRODUCT ID: 2391

Slice, store, and print your 3D files from any web enabled device with the AstroBox pack ! AstroPrint is free, open source software for...

Slice, store, and print your 3D files from any web enabled device with the AstroBox pack ! AstroPrint is free, open source software for wirelessly managing 3D printers. It features a mobile friendly user interface that works across multiple devices and screen resolutions. This pack will have you wirelessly interfacing with your 3D printer in no time! The AstroBox makes 3D printing easier to manage, eliminating the need for...

DISCONTINUED

Pimoroni Explorer HAT for Raspberry Pi

PRODUCT ID: 2426

The Explorer HAT is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer from Pimoroni there are a heap of...

The Explorer HAT is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features: 4x buffered 5V tolerant inputs Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V...

DISCONTINUED

Adafruit Pi Cobbler + Kit- Breakout Cable for Pi B+/A+/Pi 2/Pi 3

PRODUCT ID: 1990

The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use...

The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s 40 pins. That's why we now carry the Adafruit Pi Cobbler Plus - Breakout and Cable for Raspberry Pi B+. It's an add on...

DISCONTINUED

Kano Computer Kit Complete

PRODUCT ID: 3728

Do you gravitate towards more visual, hands-on projects? Have you ever wanted to build your own tablet but never knew where to begin? Now's...

Do you gravitate towards more visual, hands-on projects? Have you ever wanted to build your own tablet but never knew where to begin? Now's your chance! With the award-winning Kano Complete Computer Kit and storybook, you’ll not only build your own powerful computer, you’ll understand how you brought it to life! Kano's kit comes with a Raspberry Pi 3, an HD screen, wireless keyboard, DIY...

DISCONTINUED

Pimoroni GFX HAT - 128x64 LCD Display - RGB Backlight and 6 Touch Button

PRODUCT ID: 3935

Pimoroni's GFX HAT is a shiny new LCD Display with RGB Backlight and Touch Buttons! This is a seriously snazzy LCD that can display complex...

Pimoroni's GFX HAT is a shiny new LCD Display with RGB Backlight and Touch Buttons! This is a seriously snazzy LCD that can display complex graphics for all your headless Pi games and animations. While the LCD is monochrome 128x64 pixels, the backlight can be set to different RGB colors to indicate You also get six capacitive touch buttons for input and navigation, so you can use this as a controller too. The cool capacitive touch...

DISCONTINUED

Adafruit VESA Mount Plus for Raspberry Pi

PRODUCT ID: 2534

The basic Adafruit VESA mount got a facelift! Introducing the Adafruit VESA Mount Plus for the Raspberry Pi 3, Pi 2, Model B+, and Model A+!...

The basic Adafruit VESA mount got a facelift! Introducing the Adafruit VESA Mount Plus for the Raspberry Pi 3, Pi 2, Model B+, and Model A+! Designed by PaintYourDragon, this is a very versatile mount with support for 75mm and 100mm. Mount your Pi computer to the back of most HDMI monitors! The VESA mount is cut out of clear 3mm acrylic so you can see the LEDs. This case is for Raspberry Pi Model B+ / A+ / Pi 2 / Pi 3 only! Not...

DISCONTINUED

Pimoroni Display-O-Tron HAT

PRODUCT ID: 2694

The Pimoroni Display-O-Tron HAT is an upgraded HAT version of our Display-O-Tron 3000! The Display-O-Tron is a lovely 16x3 character LCD display...

The Pimoroni Display-O-Tron HAT is an upgraded HAT version of our Display-O-Tron 3000! The Display-O-Tron is a lovely 16x3 character LCD display with capacitive touch pads, GPIO breakout pins, and a six-zone RGB backlight (twice as bright as the older Display-O-Tron 3000)! The capacitive touch pad is ideal for navigating on-screen menus or inputting data and there are some pretty common GPIO pins added for those of...

DISCONTINUED

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Pink

PRODUCT ID: 2247

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

DISCONTINUED

C4Labs Bel-Aire Case - Enclosure for Raspberry Pi 2 & Model B+

PRODUCT ID: 2710

Flaunt your board and wrap it in style with the Bel-Aire Case - Enclosure for Raspberry Pi Model B+ / Pi 2 . The cool hot-rod design turns...

Flaunt your board and wrap it in style with the Bel-Aire Case - Enclosure for Raspberry Pi Model B+ / Pi 2 . The cool hot-rod design turns your humble little Raspberry Pi into a fiery new centerpiece that's really worth displaying! This laser-cut birch enclosure has been designed specifically for the Raspberry Pi 2 and model B+ and has been purposely crafted to provide full access to all power ports. The newly revised...

DISCONTINUED

Raspberry Pi Foundation Starter Kit with Pi 3

PRODUCT ID: 3277

To celebrate the sale of their ten millionth Raspberry Pi, the Raspberry Pi Foundation for the first time has put together their own...

To celebrate the sale of their ten millionth Raspberry Pi, the Raspberry Pi Foundation for the first time has put together their own idea of what the perfect bundle would look like, creating the official Raspberry Pi Starter Kit . This kit provides you with a keyboard, mouse, power supply, Pi enclosure, HDMI cable, and an SD card with the necessary operating system out of which you can operate. Great for...

DISCONTINUED

The Raspberry Leaf for Model B+/A+/Pi 2/Pi 3 (Two Pack)

PRODUCT ID: 2196

Have you ever tried making a connection from your Raspberry Pi B+ to a breadboard and had trouble finding the pin you need because nothing is...

Have you ever tried making a connection from your Raspberry Pi B+ to a breadboard and had trouble finding the pin you need because nothing is labelled? Have you made mistakes matching a diagram of the pinout to the actual pins? Are you not making enough connections to use our amazing Pi T-Cobbler? Try the Raspberry Leaf ! The Raspberry Leaf is a piece of high quality glossy paper that's cut and drilled to to pop over the GPIO pins of your...

DISCONTINUED

Pi Powered Times Square Traveler Pack

PRODUCT ID: 3273

Some people might want to make the trek to NYC. But for those who want to skip out on the crowds and the cold, why not bring a little bit of the Big...

Some people might want to make the trek to NYC. But for those who want to skip out on the crowds and the cold, why not bring a little bit of the Big Apple into your home with this Times Square Traveler Pack? These screens are the very same that line the billboards of NYC. With Adafruit’s best selling RGB Matrix HAT, anyone can take a shot at creating a beautiful scrolling display to rival those found in Times Square. The included...

DISCONTINUED

Pi Model B+ / Pi 2 / Pi 3 Case Base - Green

PRODUCT ID: 2251

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding COLORS!!!!!...

DISCONTINUED

Pibow Coupé Flotilla - Enclosure for Pi 2/B+/Pi 3

PRODUCT ID: 2619

"Blimey! There's a flotilla off the port bow! Man the crow's nest and batten down the mizzenmast," we yelled when a box of these...

"Blimey! There's a flotilla off the port bow! Man the crow's nest and batten down the mizzenmast," we yelled when a box of these came in. Then we opened the box and realized they were just Raspberry Pi cases from our good friends at Pimoroni! The Pibow Coupé Flotilla is the nautical blue version of the fantastically red Coupé. Like most pibow cases, this case is laser cut from high-quality...

DISCONTINUED

Raspberry Pi B+ / Pi 2 / Pi 3 Frosted White Enclosure

PRODUCT ID: 1997

Now that you have the precious - your Raspberry Pi Model B+ - it's a good idea to protect it. And while our beautifully...

Now that you have the precious - your Raspberry Pi Model B+ - it's a good idea to protect it. And while our beautifully designed Pi Box is great for showing off your B+, you might want a case that's a bit more inconspicuous. Luckily, there's the Raspberry Pi B+ / Pi 2 Frosted Enclosure from MCM. This case comes in two piece construction, base and cover, with a smooth ABS plastic finish. This...

DISCONTINUED

Particle IoT Starter Pack for Raspberry Pi - Includes Pi 3

PRODUCT ID: 3312

Particle has partnered with Adafruit to put together this kit that makes IoT easy as Pi! Connect your Raspberry Pi 3 to the Particle Cloud with this...

Particle has partnered with Adafruit to put together this kit that makes IoT easy as Pi! Connect your Raspberry Pi 3 to the Particle Cloud with this Particle Pi Starter Kit. The Raspberry Pi is already the world's most popular low-cost computer, and a powerful development tool for building connected projects. This starter pack contains the essentials of our Raspberry Pi 3 Starter Pack with added sensors that will open up your Pi to a...

DISCONTINUED

Raspberry Pi 2 Model B Starter Pack - Includes a Raspberry Pi 2

PRODUCT ID: 2380

Why not trick out your fresh new board with some accessories? The Pi 2 is a big deal - a big, big deal. It has an upgraded ARMv7 multicore...

Why not trick out your fresh new board with some accessories? The Pi 2 is a big deal - a big, big deal. It has an upgraded ARMv7 multicore procssor and a full Gigabyte of RAM - meaning you're going to see ~2x the performance on processor-upgrade only and 4x on average for mutliple-core procssors. That's up to like 7.5x increase in speed without taking into account the 1 Gig of RAM. Should you be excited? Yes....

DISCONTINUED

Pi Model B+ / Pi 2 / Pi 3 Case Base - Purple

PRODUCT ID: 2304

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding ...

DISCONTINUED

Extra-tall SMT GPIO Header for Raspberry Pi HAT - 2x20 Extra Tall Female Header

PRODUCT ID: 2714

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female...

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female header. This header allows you to plug your Raspberry Pi HAT onto a Raspberry Pi A+, B+ or Pi 2. We also carry various through-hole versions but this is for when you really need to have all the space available, such as on our 3.5" PiTFT

DISCONTINUED

Raspberry Pi B+ / Pi 2 / Pi 3 Black Enclosure

PRODUCT ID: 1998

Now that you have the precious - your Raspberry Pi - it's a good idea to protect it. And while our beautifully...

Now that you have the precious - your Raspberry Pi - it's a good idea to protect it. And while our beautifully designed Pi Box is great for showing off your B+, you might want a case that's a bit more inconspicuous. Luckily, there's the Raspberry Pi B+ / Pi 2 / Pi 3 Black Enclosure from MCM. This case comes in two piece construction, base and cover, with a smooth ABS plastic finish....

DISCONTINUED

Raspberry Pi 2 - Model B v1.2 - ARM Cortex-A53 with 1G RAM

PRODUCT ID: 2358

Didn't think the Raspberry Pi could get any better? You're in for a big surprise! The Raspberry Pi 2 Model B is out and it's amazing!...

Didn't think the Raspberry Pi could get any better? You're in for a big surprise! The Raspberry Pi 2 Model B is out and it's amazing! With an upgraded ARM Cortex-A53 quad-core processor, Dual Core VideoCore IV Multimedia coprocessor, and a full Gigabyte of RAM, this pocket computer has moved from being a 'toy' to a real desktop PC! The first upgrade was a move from the BCM2835 (single core ARMv6) to BCM2836...

DISCONTINUED

UniPi+ - Unibody aluminum case for Raspberry Pi - Model B+ / Pi 2 / Pi 3

PRODUCT ID: 2198

Give your Raspberry Pi B+ / Pi 2 / Pi 3 a Unibody with the UniPi case. Made in the U.S.A. by Pazdan LLC Tool & Die from solid Aluminum, this...

Give your Raspberry Pi B+ / Pi 2 / Pi 3 a Unibody with the UniPi case. Made in the U.S.A. by Pazdan LLC Tool & Die from solid Aluminum, this case protects your B+ from damage and looks great in your modern/designer apartment! Some nice bonus design features allow this case to be wall mounted or stackable (like a stack of tuna fish tins.) The Pi Holder case is milled by Pazdan LLC Tool & Die Machine Shop on CNC machines and comes...

DISCONTINUED

Anidees Silver Case w/ Crystal Top for Raspberry Pi B+/Pi 2/Pi 3

PRODUCT ID: 2346

Now that you have your Raspberry Pi Model B+ Pi 2 or Pi 3 - it's a good idea to protect it. And while our...

Now that you have your Raspberry Pi Model B+ Pi 2 or Pi 3 - it's a good idea to protect it. And while our beautifully designed B+ / Pi 2 Case is great for showing off your Pi, you might want an enclosure that's a bit more luxurious. Luckily, there's the Raspberry Pi B+ / Pi 2 / Pi 3 - Unibody Silver Case with Glass Top by Anidees. While it works with a Pi 3, the metal case may attenuate the...

DISCONTINUED