LEDs / Accessories

This is a beefy switching supply, for when you need a lot of power! It can supply 12V DC up to 5 Amps, running from 110V or 220V power (the plug it comes with is for US/Canada/Japan but you can use any plug adapter for your country, or just replace the cable with a standard 'figure-8' cable). The output connects to a 2.1mm DC plug. There's a green indicator light to...

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming apart...

This little remote control would be handy for controlling a robot or other project from across the room. It has 21 buttons and a layout we thought was handy: directional buttons and number entry buttons. The remote uses the NEC encoding type and sends data codes 0 thru 26 (it skips #3, #7, #11, #15, #19 and #23) to address #0. You can use this to control something...

6" (150mm) long jumper cable of 6 conductors, 0.1" spacing with two 'female'/sockets on either end. Great for wiring up ShiftBrites together! Note: Wire colors may vary.

Connect this to that without soldering using these quick terminal blocks. They allow connecting of two sets of four wires together using just a flat-head screwdriver. These are UL rated to carry up to 15 Amps, so they're great for high current LED strips! Can be used with wires from 14AWG to 22 AWG

Keep your 5mm LEDs in place with these chromed metal LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening, cork it with the plastic end, and screw on the washer for a secure grip. We have LED holders in a bevy of sizes: 10mm (plastic, beveled). 8mm (plastic, wide beveled). 8mm...

Keep your 5mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into place. We have these holders in different sizes: 10mm (beveled). 8mm (beveled). 5mm (beveled). 3mm (beveled). Comes as a pack of 5, and no...

Keep your 5mm LEDs in place with these chromed metal LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening, cork it with the plastic end, and screw on the washer for a secure grip. We have LED holders in a bevy of sizes: 10mm (plastic, beveled). 8mm (plastic, wide beveled). 8mm...

Keep your 5mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into place. We have these holders in different sizes: 10mm (beveled). 8mm (beveled). 5mm (flat). 3mm (beveled). Comes as a pack of 5, and no...

Keep your 10mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into place. We have these holders in different sizes: 8mm (beveled). 5mm (beveled). 5mm (flat). 3mm (beveled). Comes as a pack of 5, and no...

These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from...

nice whoppin' rectangular slab of some lovely black acrylic to add some extra diffusion to your LED Matrix project. This material is 2.6mm (0.1") thick and is made of special cast acrylic that makes it perfect for glowy projects, especially matrices or NeoPixels. Unlike smoke or other-tinted acrylic, this material sharpens the pixels and reduces the glare. You get a...

A nice whoppin' slab of some lovely black acrylic to add some extra diffusion to your LED Matrix project. This material is 2.6mm (0.1") thick and is made of special cast acrylic that makes it perfect for glowy projects, especially matricies or NeoPixels. Unlike smoke or other-tinted acrylic, this material sharpens the pixels, and reduces the glare. You get a great...

*pew* *pew*! This board is like a little ray gun for infrared light, with two high powered LED outputs. When controlled with the onboard N-Channel FET driver, you'll be blasting 100mA-200mA of current pulsing through each LED for 10+ meters of range! This is the easiest way to get great IR emitter range without wiring up a bunch of parts. By using a 2mm pitch STEMMA...

Yay, a plastic tube! No, we jest. This is no ordinary plastic tube, but rather a side-lighting fiber optic tube. This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive...

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have total reflection, you can get a nifty lighting effect from...

These ingenious little clips make it easier than ever to use our analog RGB LED strips - no need to solder! The clips snap onto the ends of the LED strip and hold securely. They're not waterproof but you could cover them in heat-shrink to make them weatherproof. You get one piece of three different types: One is a short "joiner" - it can join two strips together. The...

For those that want to cut, customize, and cap our awesome Digital Addressable RGB LED strips we now have a pack of the little rubber caps. These fit perfectly over the strips, use silicone glue to secure and waterproof them. Comes in a pack of 4 pieces

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have total reflection, you can get a nifty lighting effect from...

This is a beefy switching supply, for when you need a lot of power! It can supply 5V DC up to 10 Amps, running from 110V or 220V power (the plug it comes with is for US/Canada/Japan but you can use any plug adapter for your country, or just replace the cable with a standard computer/appliance power cord) The output connects to a 2.1mm DC plug. There's a green LED...

Keep your 5mm LEDs in place with these chromed metal LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening, cork it with the plastic end, and screw on the washer for a secure grip. We have LED holders in a bevy of sizes: 10mm (plastic, beveled). 8mm (plastic, wide beveled). 8mm...

Yay, a plastic tube! No, we jest. This is no ordinary plastic tube, but rather a side-lighting fiber optic tube. This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive...

Connect this to that with an IDC cable! This cable has 10 pins (2x5) in 0.1"x0.1" spacing. This is a shorter version of the cable we've carried for AVR programming, we use this for chaining together 16x24 LED matrix panels or GertBots About 1.5" long with two sockets crimped onto either side, they're quite sturdy!

Discontinued - you can grab 8mm Plastic Bevel LED Holder - Pack of 5 instead! Keep your 8mm LEDs in place with these beautiful chromed metal LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening, cork it with the plastic end, and screw on the washer for a secure grip onto a flat...

Keep your 3mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into place. We have these holders in different sizes: 10mm (beveled). 8mm (beveled). 5mm (beveled). 5mm (flat). Comes as a pack of 5, and no...

Keep your 8mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into place. Please Note: our 8mm NeoPixel LEDs are just a smidge large (for whatever reason) and so they wont snap into place, you could use a...

This cable product is no longer sold individually. We now only have them in set pairs for the same price! Get them here. This 4-wire cable is 20cm long and has a JST SM type connector receptacle on the end. It mates with the JST SM plug cable and is good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of...

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have total reflection, you can get a nifty lighting effect from...

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have total reflection, you can get a nifty lighting effect from...

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have total reflection, you can get a nifty lighting effect from...

Change your face with this unique LED mask, like it's the return of the classic Nicholas Cage/John Travolta action classic, Face/Off! Be whomever you want. This Face Changing mask uses the same LED panels from Lumen Couture's matrix line of dresses and hoodies, allowing you to fully transform your face. Comfy eye sockets and ergonomic design allow for long term wear....