This is a FTDI FT232RL usb/serial chip embedded in a cable that has a 6-pin socket at the end. These are perfect for use with a Boarduino, Meggy's, or other Arduino clones, and Fuzeboxen. Useful whenever you want to communicate with a TTL serial device, such as an XPort, GPS, XBee or SIM module through a breakout board. The version we have is the 3.3V. The data signals are at 3V and the power line provides 5V. We suggest this for any product...

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 9V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC wall power, you'll just need a low cost plug adapter. New! This adapter is now CE /...

The YBox2 is a DIY networked set-top box. Connect it to your TV and you can design customized content to be delivered direct from the Internet. This project is great for people who want a new platform to experiment with. The video and Internet cores are ready to go and easy to work with. We have some example widgets that demonstrate the YBox2's capability, and the whole project is open source so you can start hacking your own. If you've ever...

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just passes the 'raw data' along. Check the TSOP38238 datasheet for more details We have a detailed tutorial with example code and wiring diagrams showing how to...

Useful for larger electronic projects, including the YBox2 kit

Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, connect one pin to ground (either one) and the other pin to a square wave out from a timer or microcontroller. For the loudest tones, stay around 4 KHz, but works quite well from 2KHz to 10KHz. For extra loudness, you can connect both pins to a microcontroller and swap which pin is high or low...

Diffused 5mm tri-color LED with separate red, green and blue LED chips inside! Nice indicator, and fun to color-swirl. 60 degree viewing angle. We like diffused RGB LEDs because they color mix inside instead of appearing as 3 distinct LEDs. These are Common-Anode type which means you connect one pin to 5V or so and then tie the other three legs to ground through a resistor. We carry and use CA more than CC because multi-LED driver chips (such...

Introducing the Propeller Activity Board! Do more with eight cores. Harnessing the power of the 8-core Propeller microcontroller is now easier than ever before! With built-in sockets and pre-written C libraries, Parallax provides the resources for you to bring your project from idea to reality. The Propeller Activity Board gives you direct access to the most popular Propeller peripherals, including: XBee socket — control or receive data from...

The QuickStart is an evaluation board for the 8-Core Parallax Propeller. As an open-source reference design the QuickStart board provides basic Propeller circuitry. Developers may use our PCB layout files as their own to speed their project towards completion. As a project board the QuickStart is fully expandable and provides unimpeded access to all I/O pins through an expansion header but includes some button inputs and LEDs to demonstrate...

This cable comes with two nice gold-plated RCA connectors. Perfect for use with component/composite video and audio, such as the YBox kit, Propeller Quick-proto for Quickstart board, and of course a Raspberry Pi® ! Cable is 6 ft long and has 75 ohm impedance.