Components & Parts / Buttons

Slim clicky momentary switches are standard input "buttons" on electronic projects. These are half the width of classic 6mm tactile switches so they line up better on a breadboard, just plug them into every-other row. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The two pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. These buttons are bigger than the 6mm ones we carry, and come in a pack of 15. Each button comes with a candy-colored square cap that snaps on. You get three of each...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a green plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 20, they're pretty handy so you'll want to keep them around. You can find an EAGLE cad package for these in switch-omron:B3F-10XX

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a blue plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the blue...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. These buttons are bigger than the 6mm ones we carry, and come in a pack of 15. Each button comes with a candy-colored round cap that snaps on. You get three of each...

OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a white plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a red plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the red...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED...

A button is a button, and a switch is a switch, but this LED illuminated arcade buttons is in a class of its own. It's similar in size to an arcade button (and will fit in holes drilled for 'standard' 30mm buttons) but has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic, and a lamp holder fits inside. These were originally designed for...

Medium-sized clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 10, they're pretty handy so you'll want to keep them around. You can find an EAGLE cad package for these in...

Quick connector wire sets will make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.11" quick-connects pre-crimped onto 20cm long wires. The wires are then terminated together in a JST 2.5mm/0.1" spaced 2-pin connector (we don't have the exact part number yet for the connector but you can just use 0.1" header) Of course you can cut this off if you don't have use for...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built-in, we're confident that sticking a diffused LED...

A button is a button, and a switch is a switch, but this LED illuminated arcade buttons is in a class of its own. Its the same size as a 'standard' 30mm arcade but has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic, and a lamp holder fits inside. These were originally designed for 'incandescent' lamps but is easy to use with an LED,...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED...

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat red plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has...

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat white plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...

OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat green plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built-in, we're confident that sticking a diffused LED...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED...

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat blue plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...

Push once to turn on, push again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's breadboard friendly and more fun than a power switch. Can reliably handle up to 500mA and up to 50V. This is a really satisfying switch. The leads are not on a perfect 0.1" grid so for use with a breadboard just bend the leads out just a tad and snap into a solderless breadboard or perfboard.

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat yellow plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...

Super-tall clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. These are extra tall which are useful when putting your project in an enclosure and you want the buttons to stick out. They come in a pack of 10,...

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

Push once to turn one side on, push again to turn the other side on! It's basically a push-button toggle switch that connects and disconnects the middle pin from either of the two side switches with every click. This clicky switch makes a great power switch or mode toggler. We like this switch because it's easy to embed in a seam for easily powering up/off multi-wire wearable and fabric projects. Can reliably handle up to 3A and up to...

OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built-in, we're confident that sticking a diffused LED...

OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!

A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...

OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle! 16mm Panel Mount Momentary Pushbutton -...

OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!

Push once to turn one side on, push again to turn off, push again to turn the other side on, one last push and its off again! It's basically a push-button toggle switch that connects and disconnects the middle pin from either of the two side switches with every click. This clicky switch makes a great power switch or mode toggler. We like this switch because it's breadboard friendly and more fun than a power switch. Can reliably handle up...

These chrome-plated metal buttons are tough without sacrificing style. They're momentary push buttons so when you press it the ‘normally-open’ contact shorts to the common contact. When you release it, the contacts open up again.   We have blue, green, red, white, and RGB variants. Check out the product pages for more information!

Push once to turn on, push again to turn off, push again to turn the other side on, one last push and it's off again! It's basically a push-button toggle switch that connects and disconnects. This clicky Mini On/Off Button switch makes a great power switch or mode toggler. They're often referred to as 'flashlight' switches because you see them used in small flashlights. Can reliably handle up to 500mA and up to 12VDC. This is...

A new tiny squishy delight! This Black Rubber Joystick Nubbin Cap is the perfect add-on to any of your projects with a 5-way navigation joystick, like our Adafruit Mini Color TFT with Joystick FeatherWing or Adafruit 128x64 OLED Bonnet for Raspberry Pi. Fits perfectly on classic 5-way navigation joysticks like this one. It's solid, sturdy, and presses on firmly. We especially dig the cute directional etching. Pop it onto a...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...

Put your project in stealth mode with these silent Soft Tactile Switch Buttons .   T actile switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 10, they're pretty handy so you'll want to keep them...

This Mini Illuminated Momentary Power Button is an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to add a tactile switch and a colorful universal power symbol to your project.  The tact switch is about the same size as 6mm tactile switches and can snap into a breadboard. There are an additional two pins that connect to the anode and cathode of a small LED that shines through the top. Note...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have  LEDs built right in!  That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have  LEDs built right in!  That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a ~30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have  LEDs built right in!  That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...

This Mini Illuminated Momentary Power Button it an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to add a tactile switch and a colorful universal power symbol to your project.  The tact switch is about the same size as 6mm tactile switches and can snap into a breadboard. There are an additional two pins that connect to the anode and cathode of a small LED that shines through the top. Note...

You know those party platters you see at fancy events, where there's like sliced carrots on one side, and chunks of cheese on another, all divided up lovely? OK this is the exact same thing but for 6mm tactile buttons. You will never feel constrained by button colors again with this button party, lots of colors, in a handy carry case. Little clicky switches are standard input "buttons" on electronic projects. These work best in a...

Put your project in stealth mode with these super slim, super tiny, and silent   Mini Soft Touch Push-button Switches .   They're less 'clicky' than tactile switches, they have a rubbery elastomer that feels good to press. No dangly spider-leg-pins to solder as these buttons are SMD. We see these often in little game arcade pad layouts due to their small size and soft feel. They come in a pack of 10, and they're pretty...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have  LEDs built right in!  That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...

Punch in your secret key (or Jenny's number) into this numeric matrix keypad. This keypad has 16 buttons, arranged in a telephone-line 4x4 grid. The keys are connected into a matrix, so you only need 8 microcontroller pins (4-columns and 4-rows) to scan through the pad. Check the tutorials tab for links to an Arduino library and example code. We include some header so you can plug this into a breadboard with ease, some light...

By popular demand, we now have latching rugged metal push buttons with a full color RGB LED ring light! These chrome-plated metal buttons are rugged, but certainly not lacking in flair. Simply drill a 16mm hole into any material up to 1/4" thick and you can fit these in place – there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a plastic RGB LED...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...

Add some steely elegance to your project with these Metal Ball Tactile Buttons . They've got a nice industrial shine to them along with a light blue underbelly. Not only do they look good, but they're also good if you have an actuator that will be pressing the button at an angle! Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...

These Reese's Piece's lookin' bits fit perfectly on top of tactile buttons with 2.4mm square tops and give a satisfying 8mm diameter surface area for your fingers to press. You get 10 candy-colored round caps. You get two of each color: red, yellow, white, gray , and Adafruit black . Snap these onto a tactile switch body (not included) to customize your PyGamer, or anything else with 2.4mm-square-top tactile switches.  

This product is really annoying to have to write a description for because it's really something you have to touch to understand! Instead of a hard plastic actuator-button, these have a soft molded silicone button top. The underlying switch is still a clicky dome-switch but you have this nice soft grippy button for your fingers. It's incredibly satisfying to press and adds a nice upgrade to what is normally a plain tactile switch. We use...

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have  LEDs built right in!  That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and they require a 30mm diameter hole for mounting. Thus, they are sometimes referred to as 30mm...

Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. Each button comes with a candy-colored round cap snapped on. You get one of each color-- blue,...

Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.25" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this off if there's no use for it. If you need a...

Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.187" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this off if there's no use for it. If you need a...

By popular demand, we now have  latching rugged metal push buttons  with a full color  RGB LED ring  light! These chrome-plated metal buttons are rugged, but certainly not lacking in flair. Simply drill a 16mm hole into any material up to 1/4" thick and you can fit these in place – there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator,...

By popular demand, we now have rugged metal buttons with a full color RGB LED ring light! These chrome-plated metal buttons are rugged, but certainly not lacking in flair. This is a 22mm On/Off version of the RGB pushbutton. Simply drill a 22mm hole into any material up to 1/4" thick and you can fit these in place – there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal...

By popular demand, we now have rugged metal buttons with a full color RGB LED ring light! These chrome-plated metal buttons are rugged, but certainly not lacking in flair. This is a 19mm On/Off version of the RGB pushbutton. Simply drill a 19mm hole into any material up to 0.45" thick and you can fit these in place – there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal...

This wiring loom from Pimoroni has all the cables and connectors you'll need to connect a joystick, arcade buttons, and illuminated button to Picade X HAT. It's ideal for DIY arcade cabinet builds and retro gaming. The loom consists of four separate sets of wires (26AWG), all 35cm long : 5-pin female connector to 5-pin male Dupont connector 12 x spade connectors (2.8mm) to 6x 2-pin male Dupont...

These chrome-plated metal buttons are tough without sacrificing style. They're on/off switch buttons – when you press it the 'normally-open' contact shorts to the common contact and the button stays 'pressed'. When you press it a second time, the button springs open, and the contacts open up again. We have blue, green, red, white, and RGB variants. Check out the product pages for more information!

We've got plenty of round and square buttons, but these  LED Illuminated Triangle Pushbuttons  are welcome to the party. These make us think of 1960s or 70s Sci-Fi control board buttons. As  everyone  knows, triangular buttons are the  most retro-futuristic  of all button shapes. Get 6 of them together for a cool hexagonal arrangement, or just have one triangle at a time. These buttons are medium-sized, large...