Arduino / Accessories

Half-size breadboard

PRODUCT ID: 64

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the...

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the breadboard as thin as 1.4" (3.5cm) and stick it onto an Arduino protoshield. You can also cut these in half with a saw to create 2 tiny breadboards, or "snap" these breadboards together either...

$5.00

IN STOCK

9 VDC 1000mA regulated switching power adapter - UL listed

PRODUCT ID: 63

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips...

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 9V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC wall power, you'll just need a low cost plug adapter. New! This adapter...

$6.95

IN STOCK

Tiny breadboard

PRODUCT ID: 65

This a tiny little breadboard...half the size of a half-size breadboard! Measures 1.8" x 1.4" (46mm x 36mm ) Perfect for tiny projects and...

This a tiny little breadboard...half the size of a half-size breadboard! Measures 1.8" x 1.4" (46mm x 36mm ) Perfect for tiny projects and for sticking onto the top of Arduino protoshields!

NOTIFY ME

$4.00

OUT OF STOCK

Arduino bootloader-programmed chip (Atmega328P)

PRODUCT ID: 123

This is a preprogrammed Atmega328P chip, useful if you want to make your own Arduino-compatible or repair a damaged chip on an exisiting Arduino UNO,...

This is a preprogrammed Atmega328P chip, useful if you want to make your own Arduino-compatible or repair a damaged chip on an exisiting Arduino UNO, Duemilanove, Diecimila, or NG! This chip is programmed with 'ADAboot', my version of the bootloader that is "quick-start" NG/diecimila/duemilanove/UNO-compatible. This means that there is still a 5-second delay from when you press the reset button to when the Arduino runs the...

NOTIFY ME

$5.95

OUT OF STOCK

9V battery holder with switch & 5.5mm/2.1mm plug

PRODUCT ID: 67

This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm center-positive barrel plug. Use this to battery-power your Arduino (or...

This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm center-positive barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box! Battery & screw not included.

NOTIFY ME

$3.95

OUT OF STOCK

USB Cable - Standard A-B - 3 ft/1m

PRODUCT ID: 62

This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things). 3 feet /...

This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things). 3 feet / 1 meter long Color may vary!

$2.95

IN STOCK

9V battery clip with 5.5mm/2.1mm plug

PRODUCT ID: 80

I found these high-quality battery clips. They're molded plastic so they wont tear like cheap clips, and they cover the battery terminals to...

I found these high-quality battery clips. They're molded plastic so they wont tear like cheap clips, and they cover the battery terminals to prevent shorts. Comes with a 5.5mm/2.1mm center-positive barrel connector, assembled! Battery not included

NOTIFY ME

$2.95

OUT OF STOCK

In-line power switch for 2.1mm barrel jack

PRODUCT ID: 1125

Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed!...

Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an in-line switch that is rated for 125V and 2Amps (its normally used for lamps, we suppose). Since most people will be using it with no more than 12VDC, we...

$2.50

IN STOCK

Plastic mounting plate for breadboard and Arduino - rubber feet!

PRODUCT ID: 275

By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There...

By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half sized breadboard very nicely. THIS DOES NOT FIT THE ARDUINO MEGA. Comes with: 3mm thick plastic plate with engravings2 x 4-40 3/8" machine screws for attaching your Arduino4 x 4-40 hex nuts4 x rubber bumpers, keeps the board from...

$5.00

IN STOCK

Ethernet Cable - 10 ft long

PRODUCT ID: 730

We have so many Internet-connected goodies in the shop, we figured it's time to carry a cable so you can easily connect them up! This cable is 10...

We have so many Internet-connected goodies in the shop, we figured it's time to carry a cable so you can easily connect them up! This cable is 10 feet long, black and has all 8 wires installed. Perfect for use with the BeagleBone, Arduino Uno Ethernet, Arduino Ethernet Shield, NETduino Plus, Patch Shield, PoE Injector cables, IoT Printer pack or any other Ethernet-cable-needing product! This is a 'straight-thru' cable, not a...

$2.95

83 IN STOCK

Half Size Breadboard + 78 Piece 22AWG Jumper Wire Bundle

PRODUCT ID: 3314

This is a cute half-size breadboard with an assortment of small jumper wires, great for prototyping. Breadboard is 2.2" x 3.4" (5.5 cm x...

This is a cute half-size breadboard with an assortment of small jumper wires, great for prototyping. Breadboard is 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. Power rails can be pulled off easily to make the breadboard as thin as 1.4" (3.5cm). The jumper wires are pre-cut and bent in right angles at the ends, so you can choose the appropriate length for your...

NOTIFY ME

$9.95

OUT OF STOCK

Shield stacking headers for Arduino (R3 Compatible)

PRODUCT ID: 85

“How could something so simple be so useful?” We heard once that in the 4th millenium B.C. some guy asked the person who...

“How could something so simple be so useful?” We heard once that in the 4th millenium B.C. some guy asked the person who invented the wheel that question. The person who invented the wheel’s answer, we were told, was something like “well it’s not actually that simple - it required engineering and innovation and this thing called mathematics that probably hasn’t been discovered yet and...

NOTIFY ME

$1.95

OUT OF STOCK

USB cable - USB A to Micro-B - 3 foot long

PRODUCT ID: 592

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long

$2.95

IN STOCK

Half-Size Breadboard with Mounting Holes

PRODUCT ID: 4539

This cute 3.2″ × 2.1″ (82 × 53mm) solderless half-size breadboard has four bus lines and 30 rows of pins, our favorite...

This cute 3.2″ × 2.1″ (82 × 53mm) solderless half-size breadboard has four bus lines and 30 rows of pins, our favorite size of solderless breadboard for projects. You get a whoppin' 400 tie points ! Plug in a Feather or Metro Mini with the rest for sensors or buttons or even a little display. You can pull the power rails off easily to make the breadboard as thin as 1.4" (3.5cm). You can also cut these in...

NOTIFY ME

$5.00

OUT OF STOCK

12V DC 1000mA (1A) regulated switching power adapter - UL listed

PRODUCT ID: 798

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips...

This is a really nice power supply. It's a switching DC supply so its small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 12V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC wall power, you'll just need a low cost plug adapter. New! This...

NOTIFY ME

$8.95

OUT OF STOCK

Adafruit PowerBoost 500 Shield - Rechargeable 5V Power Shield

PRODUCT ID: 2078

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable...

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield goes onto your Arduino and provides a slim rechargeable power pack, with a built in battery charger as well as DC/DC booster. Compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due - basically any Arduino-pinout-shaped Arduino as only the GND and 5V pins are used. You can stack shields...

$19.95

1 IN STOCK

Clear Enclosure for Arduino or Metro

PRODUCT ID: 3597

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it for sure with the Arduino...

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it for sure with the Arduino UNO R3, Adafruit Metro and Adafruit Metro Express. It's clear so you can see all your onboard LEDs and silkscreen labels. There are four small screws you can use to affix the board and some bumpers that go on the bottom. We rather like this case because it's low-profile enough that...

NOTIFY ME

$4.95

OUT OF STOCK

USB Battery Pack - 2200 mAh Capacity - 5V 1A Output

PRODUCT ID: 1959

A smaller-sized rechargeable battery pack for your Raspberry Pi or Raspberry Pi B+ (or Arduino, or Propeller, or anything...

A smaller-sized rechargeable battery pack for your Raspberry Pi or Raspberry Pi B+ (or Arduino, or Propeller, or anything else that works with 5V!). This pack is intended for providing power to an iPhone, cell phone, tablet, etc but we found it does a really good job of powering other miniature computers and micro-controllers. If you want more power we have a 4400mAh version and if you want even more...

$14.95

17 IN STOCK

Plastic Translucent Enclosure for Metro or Arduino - LEGO Compatible

PRODUCT ID: 4490

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it with the Arduino UNO R3,...

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it with the Arduino UNO R3, Adafruit Metro, and Adafruit Metro M4 Express. We rather like this case because it's low-profile enough that you can fit shields on top. There's even a flexi-nub for pressing the reset button! Best of all, it's LEGO brick compatible! So easy, we think this will enable many...

NOTIFY ME

$4.95

OUT OF STOCK

Digital Loggers PLDuino - ATmega2560 + ESP8266 Customizable PLC

PRODUCT ID: 3418

Need an easy-to-use but powerful control solution for more industrial-type projects? Get the controller that does exactly what you want in a sturdy,...

Need an easy-to-use but powerful control solution for more industrial-type projects? Get the controller that does exactly what you want in a sturdy, contained package. Combine Arduino simplicity, ESP8266 WiFi connectivity, and Digital Logger's experience and reliability to customize your own PLC for controlling industrial and robotics projects. Digital Loggers PLDuino is a PLC (Programmable Logic Controller) that is based on the...

NOTIFY ME

$194.95

OUT OF STOCK

White Enclosure for Arduino - Electronics enclosure - 1.0

PRODUCT ID: 271

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box! Here are all the details: Dimensions:...

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box! Here are all the details: Dimensions: 3.6" x 5" x 1.35"Injection molded ABS plasticEnclosure is easy to machine, drill, cut and shape to what you needBrass screw inserts (can be used and reused many times, very durable!)Fits standard Arduinos and 16 x 2 LCDsFits Arduino with Adafruit Protoshield on top with .45"...

$15.00

24 IN STOCK

Clear Enclosure for Arduino - Electronics enclosure - 1.0

PRODUCT ID: 337

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box now available in clear plastic, the...

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box now available in clear plastic, the future! Here are all the details: Dimensions: 3.6" x 5" x 1.35"Injection molded clear plasticEnclosure is easy to machine, drill, cut and shape to what you needBrass screw inserts (can be used and reused many times, very durable!)Fits standard Arduinos and 16 x 2 LCDsFits Arduino with...

$15.00

28 IN STOCK

Adafruit AVR Sticker for Breadboard Arduino-compatibles - 10 pcs

PRODUCT ID: 554

These stickers are a must for anyone making a breadboarded Arduino-compatible. They fit right on top of a DIP ATmega328 (or '168) chip, and...

These stickers are a must for anyone making a breadboarded Arduino-compatible. They fit right on top of a DIP ATmega328 (or '168) chip, and clearly indicate every pin as it would be called in the Arduino IDE. No more looking up the datasheet or schematic! The stickers are made of a tough vinyl, usually used for bumper stickers, so they will not fade, scratch, or wrinkle. The stickers are die cut already into a rounded rectangle that fits on...

$2.95

IN STOCK

Smoke Translucent Enclosure for Arduino - Electronics enclosure - 1.0

PRODUCT ID: 821

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box now available in gray translucent...

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box now available in gray translucent plastic, the future! Here are all the details: Dimensions: 3.6" x 5" x 1.35"Injection molded gray translucent plasticEnclosure is easy to machine, drill, cut and shape to what you needBrass screw inserts (can be used and reused many times, very durable!)Fits standard Arduinos and 16 x 2...

MORE INFO

DISCONTINUED