Arduino / Shields

The original Adafruit Motorshield kit is one of our most beloved, so we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work for your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors but added many improvements:...

We've taken our popular Adafruit PN532 breakout board and turned it into a shield - the perfect tool for any 13.56MHz RFID or NFC application. The Adafruit NFC shield uses the PN532 chip-set (the most popular NFC chip on the market) and is what is embedded in pretty much every phone or device that does NFC. This chipset is very powerful, and can pretty much do it...

Here's a handy Arduino shield: we've had a lot of people looking for a dedicated and well-designed data logging shield. We worked hard to engineer an inexpensive but well-rounded design. Not only is it easy to assemble and customize, it also comes with great documentation and libraries. Our latest version of this popular shield has all the features of the popular...

Brand new and better than ever, we've replaced our Adafruit GPS shield kit with this assembled shield that comes with an Ultimate GPS module. This GPS shield works great with any "Arduino shaped" board that has SPI and UART pins available, and is designed to log data to an SD card. Or you can leave the SD card out and use the GPS for a geocaching project, or maybe a...

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this...

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the Blue & White 16x2 LCDs we stock in the shop. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another pin to control the backlight for a total of 7 pins. That's almost half of the pins available on a classic Arduino! With this in...

Make your own Arduino motor party with a motor shield and a fine assortment of motors! New! we've upgraded the shield to our new version 2, with more powerful drivers, and uses fewer pins to boot! Included in this add-on pack is: Adafruit Motor Shield v2 for Arduino. 6 Volt DC hobby motor. Small stepper motor. Standard size servo. Micro size servo. An Arduino is not...

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a total of 9 pins. That's half of the pins available on a classic Arduino!...

You want to make a cool Arduino robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that the Arduino has only a few PWM outputs, and maybe those outputs are conflicting with another shield! What now? You could give up OR you could just get our handy...

This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board and remixed it into an Arduino shield complete with microSD card slot and a 5-way joystick navigation switch and three selection buttons! Since the display uses only 4 pins to communicate and has its own pixel-addressable...

The next generation Proto-ScrewShield is a dual-purpose prototyping shield. Not only does it have a large 0.1" grid prototyping area but it also extends the Arduino pins to sturdy, secure, and dependable screw terminal blocks. You even get a few bonus terminals for extra GND and four 'free' terminals for whatever connections you wish! New! As of June 23, 2014 we now...

Put on your sunglasses before putting this shield onto your 'duino - 40 eye-blistering RGB LEDs adorn the NeoPixel shield for a blast of configurable color. Arranged in a 5x8 matrix, each pixel is individually addressable. Only one pin (Digital #6) is required to control all the LEDs. You can cut a trace and use nearly any other pin if you need some customization. To...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do...

Add some sizzle to your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection and a capacitive touchscreen. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and...

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital pins, 6 to control the LCD and then another 3 to control the RGB backlight for a total of 9 pins. That's half of the pins available on a classic Arduino!...

This prototyping shield is the best out there (well, we think so, at least), and now is even better with Version R3 - updated for the most compatibility with just about all the Arduinos! It works with UNO, Mega, Leonardo, NG, Diecimila, Duemilanove, and compatible Arduinos. Yun's and Arduino Ethernets have a chunky Ethernet jack that gets in the way of stacking, you...

Includes! Adafruit data logger shield for Arduino. 8 GB SD card. Photocell. Through-Hole Resistors - 10K ohm 5% 1/4W - Pack of 25. Temperature sensor (-40 degC to 125 degC). 6 x AA battery holder with 2.1mm jack (unassembled). You'll need 6 AA batteries, a CR1220 coin cell, some wire and soldering tools to assemble the project. For more information, including...

The TinyG project is a high performance, USB based CNC 6-axis controller that supports XYZ linear and ABC rotary axes with 4 motor outputs. It is designed for small CNC applications and other applications that require highly controllable motion control. TinyG is meant to be a complete embedded solution for small or medium motor control. Main Features: Full,...

This shield kit pack will allow you to turn any Arduino into an AVR chip burner! It is specifically designed for people who want to program Atmega328P's to turn them into Arduino bootloader chips using an AVR-ISP sketch, but it can also be used to make a 'standalone' AVR ISP programmer - so that you can program blank chips without a computer! We use this set up in...

Create your very own Arduino-controlled 3-axis CNC machine with the gShield. The gShield for Arduino (formerly known as grblShield) is a complete hardware solution for Dank’s CNC motion control system called grbl. The gShield is compatible with the Uno and other 328p versions of the Arduino development platform. Version 5 is now compatible with running TinyG on...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do...

We really like the range of LCDs we stock in the shop, such as our classic blue & white and the fancy RGB negative and RGB positive. Unfortunately, these LCDs require quite a few digital pins: 6 to control the LCD and then another 3 to control the RGB backlight for a total of 9 pins. That's half of the pins available on a classic Arduino! The 16x2 Character LCD...

This touch-able add on shield for Arduinos will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like touch-reactive tablets and phones, as well as control panels for appliances, which is where...

Would you like to add powerful and easy-to-use Bluetooth® Low Energy to your robot, art or other electronics project? Heck yeah! With BLE now included in modern smart phones and tablets, its fun to add wireless connectivity. So what you really need is the new Adafruit Bluefruit LE Shield for Arduino! The Bluefruit LE Shield makes it easy to add Bluetooth® Low...

Our RGB matrices are dazzling, with their hundreds or even thousands of individual RGB LEDs. Compared to NeoPixels, they've got great density, power usage and the price-per-LED can't be beat. But...(isn't there always a but?) You need to use our special library to control them, and they require a bunch of wires to be plugged in. Tougher than a single-wire connection...

Give your Arduino project a lift with the Adafruit AirLift Shield - a shield that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite Arduino-compatible (like the Metro M4 or the classic Metro 328) that comes with its own set of awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a...

Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer...

Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer...

Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduino 328's that solves this problem. It can play up to 22KHz 12bit uncompressed audio files of any length. It's low cost, available as an easy-to-make kit. It has an onboard DAC, filter and op-amp for high quality output. Audio files are read off of an SD/MMC card, which...

Its a Wave shield party pack! Just add an Arduino to create your own iPod-killer, audio art, sound-effects box... Comes with: Latest Wave shield kit, works with more SD cards and with older NG Arduinos! Unassembled. 8 GB SD card (brand or size may change, but we test one of each kind to verify it works well). Speaker - 3" diameter (77mm), 8 ohm impedence, good...

Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper 'static' displays - that means the image stays on the display even when power is completely disconnected. The...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from creating or developing a WiFi Arduino shield. NO LONGER! The CC3000 hits that sweet...

The Arduino Ethernet Shield R3 (assembled) allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the...

This kit brings the excellent design and tutorials of Parallax to the Arduino world. Make your Arduino the onboard brain of a mobile robot and learn robotics, electronics, and programming with this versatile kit and its accompanying step-by-step lessons. The Board of Education Shield plugs into your own Arduino (not included) and mounts on the popular Boe-Bot robot...

We are excited to add another product to our growing Adafruit Bluefruit line, this time it's the Bluefruit EZ-Link: the best Bluetooth Serial Link device ever made. Like you, we have purchased all sorts of Bluetooth serial link modules, with high expectations - we just wanted something that worked! But nothing ever did exactly what we wanted: there was always some...

This is an extra large proto-shield, specifically designed for the Mega! It comes with PCB, two buttons and a full set of stacking headers. You can stack this shield easily since it comes with extra long female headers The kit includes: 1 x MEGAshield PCB. 2 x tactile switch. 1 x 3-pin male header. 1 x 2x3-pin stacking female header. 1 x 10-pin stacking female...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from creating or developing a WiFi Arduino shield. NO LONGER! The CC3000 hits that sweet...

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield goes onto your Arduino and provides a slim rechargeable power pack, with a built in battery charger as well as DC/DC booster. Compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due - basically any...

Gameduino 2 is a shield that adds a bright 4.3 inch touchscreen, an embedded GPU, headphone jack, accelerometer and microSD slot to your Arduino - or anything else with an SPI interface. Everything you need to create compelling games – right in your hand. Sound output is via an amplified headphone jack. The system supports a selection of built-in samples and...

The patch shield is a cross between a patch panel/bay and a Wingshield. Its designed for times when you want to have remote sensors, or a control panel, or LEDs, or...practically anything where you want to avoid doing a lot of icky wiring! The shield comes with 4 breadboard-friendly satellite headers. To connect, use any off-the-shelf Ethernet cable. On the shield...

Build your very own Arduino-based portable gaming toy with this kit from Tech Will Save Us! The DIY Gamer Kit is an Arduino controlled gaming device. Once you solder the whole thing together, you'll have an 8x8 LED matrix display that serves as the device's screen. From there, just easily upload your game's code onto an Arduino (not included) and play! It's a great...

Think you can do better? Design your own shield on the cheap with this DIY parts kit. You get a 3.2" x 2.5" (~ 8.1cm x 6.3cm) single-sided phenolic board with copper solder pads and mounting holes and a extra-special stacky header set. This one has one magical 8-pin header that has been bent so that you can plug it into the 'not-quite-0.1"-spacing" arduino headers...

Works with the Uno! This prototyping shield is the best out there (well, we think so, at least). It works with UNO, NG, Diecimila and Duemilanove Arduinos. You can use it with a Leonardo but it will not break out the hardware SPI pins (they're only on the ISP connector underneath) or the IOREF/SDA/SCL pins. However, the SDA/SCL pins on the Leonardo are also on...

This is just the PCB for a proto shield. No other parts are included. This shield is designed for the Arduino Uno, NG and Decimila Arduinos. For parts list and instructions, please visit the website

This kit is now discontinued. We've upgraded the Adafruit Motor Shield v1 to v2, with stacking-support and higher-current motor drivers, Please check out the v2 shield - its much better! Here is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects. 2 connections for 5V 'hobby' servos connected to the Arduino's...

The Video Game Shield is an Arduino add-on shield to make your own video games, including graphics, text, sound effects, and music! Using the power of open source, this Shield includes everything you need to make awesome black-and-white video games on your TV. It supports up to two Nintendo Wii Nunchuck controllers for an easy and familiar interface. Do you need to...

We've discontinued this version of the shield (which was expensive and difficult to make) and replaced it with a version 2: its got a better price, uses way fewer pins, is Mega/Leonardo compatible and has a great touchscreen controller built in. Wow! Check it out here. Spice up your Arduino project with a beautiful large touchscreen display shield with built in...

Gameduino is a game adapter for Arduino - or anything else with an SPI interface - built as a single shield that stacks up on top of the Arduino and has plugs for a VGA monitor and stereo speakers. The sound and graphics are definitely old-school, but thanks to the latest FPGA technology, the sprite capabilities are a step above those in machines from the past....

This product has been discontinued, please see our new updated assembled version. Here's a handy Arduino shield: we've had a lot of people looking for a dedicated and well-designed data logging shield. We worked hard to engineer an inexpensive but well-rounded design. Not only is it easy to assemble and customize, it also comes with great documentation and libraries....

GPS shield for Arduino kit with data-logging capability. After building this easy kit, you can create your own geo-locative project. Please note that this shield does not come with a GPS module, they are sold separately (see below) This shield is designed to make GPS projects straight-forward and easy. Plug in a supported GPS module and run any of the example Arduino...

The W5500 Ethernet Shield for Arduino from Seeed Studio is a great way to set up your projects with internet connectivity with just a single chip. Similar to the Arduino Ethernet Shield, but with a newer chipset, this ethernet shield supports both TCP and IP Protocols in TCP, UDP, ICMP, IPv4, ARP, IGMP, and PPoE format. The RJ45 ethernet port is also low enough so...

Arduino has discontinued this shield, please check out the Adafruit WINC1500 shield for a nearly-identical replacement with the same exact module, and the addition of a micro SD card holder and prototyping area. Arduino WiFi Shield 101 is the new IoT enabler shield based on the ATWINC1500 module, developed with ATMEL, that connects your Arduino to the internet...

DISCONTINUED - You can grab Adafruit Bluefruit LE Shield - Bluetooth LE for Arduino instead! 1Sheeld+ is a "Bluetooth LE Tethered" shield for Arduino. Plug it into your Arduino and then run the matching mobile app on your tablet or phone. Once paired, the mobile app that allows the usage of all your smartphones' capabilities such as LCD Screen, Gyroscope, Switches,...