Raspberry Pi / Accessories

Looking for the best heat sink for your Raspberry Pi? Check out this nice and tall 15x15x15mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 or 4 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy....

Looking for a nice way to cool down your Raspberry Pi 3? Check out this 14x14x8 Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface...

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USBSerial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the...

Our all-in-one 5V 2.5 Amp + MicroUSB cable power adapter is the perfect choice for powering single-board computers like Raspberry Pi, BeagleBone, or anything else that's power-hungry! This adapter was specifically designed to provide 5.25V, not 5V, but we still call it a 5V USB adapter. We did this on purpose to solve a problem that occurs often with USB-powered...

Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy....

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flashcards, and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V. Here we've got a 4-channel I2C-safe Bi-directional Logic Level Converter that has open-drain-with-10K-pullups outputs, great for logic...

Looking for another way to keep your project cool? Hook up this 5V Mini Cooling Fan and prevent from overheating! Of course, it's also great for use with any small computer or FPGA or motor driver or anything that needs cooling. We also carry a mini 5V cooling fan with regular JST 2-pin connectors. This fan is nearly identical - it has the same fan body, but the...

The official Raspberry Pi USB-C power supply is here! And of course, we have 'em in classic Adafruit black! Superfast with just the right amount of cable length to get your Pi 4 projects up and running! Best for use with Pi 4 series, Pi 5's want the 5A version. Features: AC 100-240V 50/60Hz input with US plugs. DC 5.1V 3A output. 15.3W maximum output power. 1.5m 18...

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero, or any other single-board computer with the Zero4U! This is a 4-port USB 2.0 hub, almost identical to this one, but without the ferrite bead, standoffs or pogo pins. This might be a preferable format if you want to mount it on the bottom or side-by-side or with...

Looking for another way to keep your Raspberry Pi cool? Hook up this 5V Mini Cooling Fan and prevent your hard-working Pi from overheating! Of course, it's also great for use with any small computer or FPGA or motor driver or anything that needs cooling. Plug the fan directly into your Raspberry Pi's 5V+GND GPIO power pins, as shown, for instant cooling! Place in...

The Raspberry Pi 5 Active Cooler is compatible with the Raspberry Pi 5 and the Raspberry Pi 5 Case. Designed for anyone who wants to push the performance of their Pi, as well as overclockers and other power users, it keeps your Raspberry Pi 5 at a comfortable operating temperature even when under heavy load thanks to both a mini heatsink that goes on top of your CPU...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display, for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 300mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order...

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins, and for those of us who like to hack electronics, they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power...

Do you ever find yourself saying, "Gee whiz I wish I could plug in 4 more USB devices to my tablet, or microcontroller with USB host, or a Pi Zero?" I did - literally every single day. But then I found this Micro USB powered hub and stopped having to repeat myself! This mini USB hub has four USB 2.0 ports each with a max total transmission speed up to 480 MBps. All...

Optimise data transfer speeds on your Raspberry Pi computer with an official Raspberry Pi 32GB microSD card. Rigorously tested to ensure optimal performance on Raspberry Pi computers, these Class A2 microSD cards help ensure you get the smoothest user experience from your device. Pre-formatted to FAT32, so it works out of the packaging with our projects. Ideal for...

This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 5V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero with the Zero4U! This is a 4-port USB hub for Raspberry Pi Zero, and it can be mounted back-to-back onto a Pi Zero. The 4 pogo pins on the back will connect the PP1, PP6, PP22 and PP23 testing pads on your Raspberry Pi Zero – no soldering required! This item...

That new Raspberry Pi 500 computer you just got has a row of 2x20 pin headers on the right side - those are the GPIO (general purpose input/output) pins, and for those of us who like to hack electronics, they are where the real fun lies. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power...

Stop fiddling with micro SD card sockets in the back of your latest gadget during development, and give yourself a little more elbow room with this Small Micro SD Card Extender. This is a great hack for length constraints with 3D printers, single-board computers, data-logging kits and more. Get to your micro SD card in and out without using your fingernails! Insert...

Need to add analog inputs? This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the Raspberry Pi computer because it's fun to have analog inputs but the Pi does not have an ADC. We have a tutorial and code...

If you're looking for the most compact li'l display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit 128x32 PiOLED is your little OLED pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The PiOLED comes with a monochrome 128x32 OLED, with sharp white pixels. The OLED uses...

Need a USB jack for charging or powering a project, but don't want to lug around a computer? This switching supply gives a clean regulated output at up to 1000mA! 110 or 240 input, so it works in any country. The plugs are "US 2-prong" style so you may need a plug adapter, but you can pick one up at any hardware store for a $1 or so. This adapter was specifically...

This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface. It's affordable but sounds great! The NXP UDA1334A is a jack-of-all-I2S-trades: you can use 3.3V - 5V logic levels (a rarity) and can process multiple different formats by setting two pins to high or low. The DAC will process data immediately and give you a...

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. They come in both male and female, and use crafty little retaining nubbins to grip tightly into the holes on the PCB. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer...

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with a Micro SD Card Extender . This simple, but effective device gives you a long flexible cable, a psuedo Micro SD card on one end, and a matching micro SD card socket on the other. Plug in the card half and attach the socket wherever you like. This is a great hack for...

The Raspberry Pi has an on-board audio jack, which is super handy for all kinds of sound effects and speech, just plug and go! However, for when you want better audio for music playback, a USB audio card can greatly improve the sound quality and volume. That's because the on-board audio is generated by a PWM output and is minimally filtered. Don't get us wrong, it's...

Witty Pi is an add-on board that adds real time clock and power management to your Raspberry Pi. It can define your Raspberry Pi’s ON/OFF sequence and significantly reduce energy use. Witty Pi 4 L3V7 is the new member of the fourth generation of Witty Pi, and it is designed to work with 3.7V Lithium (ion or polymer) battery (that’s what L3V7 stands for)...

The quick brown fox jumps over the lazy dog. The quick brown fox jumps over the lazy dog. The quick brown fox - sorry! We were practicing our typing ON THIS NEW AWESOME KEYBOARD. With 88 dedicated keys and 12 function keys, totaling 100 keys altogether, this 'standard size' keyboard is the perfect on-the-go accessory to your Pi or everyday computer when your project...

This short-style white microSD adapter slides in where the SD card goes but is 11mm shorter (excluding the silver lip). This makes it stick out a lot less and makes for a more elegant (and less accident-prone) project. All you have to do is pop in a microSD card for a sleeker look! The outer edge of the SD adapter has a deep groove for a fingernail to pull on for...

If you want a general-purpose USB Power Delivery supply, the official Raspberry Pi 45W USB-C power supply makes for a good quality PD supply that provides high current at a large option of voltages, including 12V which is not always supported, and 5A and 5V which also is a bit rare but makes it great for USB-powering of LEDs and servos/motors. Works wonderfully with...

Witty Pi 4 is an add-on board that adds real-time clock and power management to your Raspberry Pi. It can define your Raspberry Pi’s ON/OFF sequence and significantly reduce energy usage. Witty Pi 4 is the fourth generation of Witty Pi, and it has these hardware resources onboard: Factory calibrated and temperature compensated real-time clock with ±2ppm...

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with an SD Card Extender. This simple, but effective device gives you a long flexible cable, a pseudo-card on one end, and an SD card socket on the other. Plug in the SD card half and attach the socket wherever you like. This is a great hack for length constraints with 3D...

This is a generic USB game controller, which plugs into to provide a two-handed gaming experience for retro gaming, or really any game you want to use a handheld rather than keyboard controller! Use it with your Raspberry Pi or desktop computer while playing emulated games, or as a controller to your CNC machine. It appears as a game-pad device (not keyboard or...

Here's another super handy add-on for your Raspberry Pi computer, perfect for 'head-less' setups! The PiUART adds a USB Type-C to serial connection so you can use any serial port software to connect to the Pi's console. It plugs in and is fast and easy to add whenever you need to connect to your Pi. Two LEDs connect to RX and TX on the serial converter chip so you...

Do you want your cup to runneth over with USB ports? Do you want it to also be filled with the sweet, sweet nectar of an on-off switch? If the answer to either of those questions is yes - or "I never really thought about it that way but I guess so" - then this is the perfect product for you! This USB hub has four USB 2.0 ports each with a max total transmission speed...

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with an SD Card Extender . This simple, but effective device gives you a long flexible cable, a pseudo-card on one end, and an SD card socket on the other. Plug in the SD card half and attach the socket wherever you like. This is a great hack for length constraints with 3D...

Witty Pi is an add-on board for Raspberry Pi that brings real-time clock (RTC) and power management functionalities to your Raspberry Pi. It can define the on/off sequence of your Raspberry Pi, perform power on/off actions based on temperature or voltage thresholds, and significantly reduce overall energy consumption. Witty Pi 5 HAT+ is the fifth generation of the...

Add a good quality, slim chiclet keyboard as well as an optical mouse to your Raspberry Pi, Beagle Bone Black or other mini-computer with this wireless combo set. Best of all, it only uses a single USB port! This combo comes with a sleek black chiclet keyboard and mouse both controlled by a single wireless USB dongle. The keyboard is a full QWERTY keyboard and is...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! All you need is this handy PoE module, and access to the center-taps on your Ethernet-capable board. Attach the four input wires, and get regulated 5V 1.8A on the other side. Amazing! This version of the PoE module...

Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi and Beagle Bone's USB port to add a low cost, but high-reliability wireless link. We tried half a dozen modules to find one that works well with the Pi and Bone without the need of recompiling any kernels: its supported by the Bone's Angstrom installation that comes with...

Add a typing interface to your project with this microcontroller-friendly miniature keyboard. We found the smallest PS/2+USB keyboard available, a mere 8.75" x 4.65" x 0.6" (220mm x 118mm x 16mm)! It's small but usable to make a great accompaniment to either a microcontroller project or a computer such as the Beagle Bone or Raspberry Pi. The keyboard supports either...

This is the 6mm Wide Angle Lens, an add-on for the Raspberry Pi High Quality Camera. It has a wide field of view and a variety of uses, like CCTV applications, or of course, cat photos. Includes a thumbscrew to quickly and easily assemble onto the HQ Camera Board. Wide angle lenses are good for getting shots of a big area, for wildlife cameras, security cameras,...

Witty Pi 4 Mini is an add-on board that adds real time clock (RTC) and power management to your Raspberry Pi. It can define your Raspberry Pi’s ON/OFF sequence, and significantly reduce the energy usage. Witty Pi 4 Mini is the fourth generation of Witty Pi and it has these hardware resources onboard: Factory calibrated and temperature compensated realtime clock...

Add a good quality, slim keyboard to your Raspberry Pi, Beagle Bone Black, or other single-board-computer with this sleek black chiclet keyboard. It's a full QWERTY keyboard with a USB cable and is compatible with all operating systems. We tried many keyboards to find one that felt good for everyday use and didn't take up too much room. This is an every day HID...

The Raspberry Pi USB 3 Hub provides extra connectivity for your USB devices, turning one USB-A port into four. Inside it uses the Infineon CYUSB3340 for 5 Gbit/s USB 3.2 Gen1 support An optional external USB-C power input supports high-power peripherals, you can use the official Raspberry Pi USB C Power Supply for that. For lower-power peripherals, no external power...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! All you need is this handy PoE module, and access to the center-taps on your Ethernet-capable board. Attach the four input wires, and get regulated 5V 1.5A on the other side. Amazing! This module works well with the...

Add a miniature wireless controller to your computer project with this combination keyboard and touchpad. We found the smallest wireless USB keyboard available, a mere 6" x 2.4" x 0.5" (152mm x 59mm x 12.5mm)! It's small but usable to make a great accompaniment to a computer such as the Beagle Bone or Raspberry Pi. The keyboard itself is battery powered (there's a...

Mary Poppins had her TARDIS-like carpet bag. 90s kids had their Pokémon card binders. But we have the next best thing: microSD Holder, a super-slim 8-piece microSD storage card. The most useful thing you didn't know you needed. Each order contains one holder that can keep 10 x microSD cards. If you're working with single board computers like the Raspberry Pi...

Add both WiFi and Bluetooth® to your computer super fast with this Xinghuatian Tech Combination WiFi + Bluetooth® 4.0 USB Adapter! This little two-faced cutie is so versatile! Its Wi-Fi half can be used to make Internet of Things devices cable-free, or we can also take advantage of a single-board Linux computer's USB ports to add a low-cost, high-reliability...

Proudly show off your love for the one and only, Raspberry Pi! This is the official (and approved by the foundation) Raspberry Pi® enamel pin for use with educators, classrooms, workshops, Maker Faires, TechShops, Hackerspaces, Makerspaces, and around the world to reward beginners on their skill building journey!

You are learning to use the small Linux based board, the Raspberry Pi! Adafruit offers a fun and exciting "badges" of achievement for electronics, science and engineering. We believe everyone should be able to be rewarded for learning a useful skill, a badge is just one of the many ways to show and share. This is the "I made something with a Raspberry Pi" badge for...

Power your Raspberry Pi Build HAT projects with the Raspberry Pi Build HAT Power Supply. This 48W power supply will power the Build HAT and connected LEGO Technic motors, as well as your Raspberry Pi computer. Outputs 8V DC (yep, that's the LEGO Technic voltage requirement) at 6A for plenty of power to your robotic project with left-over current that is stepped-down...

Unlock ultimate performance for I/O intensive applications on Raspberry Pi 5 with a Raspberry Pi NVMe SSD. These SSD drives are specified by the Pi Foundation to have the best performance-for-price, and will work perfectly with any M.2 HAT or adapter (we stock many varieties). Features: 256GB capacity. High-performance Raspberry Pi NVMe SSD capable of:50k IOPS* (4kb...

When your Raspberry Pi project requires multiple power supplies, why not check out the new Zero2Go Omini? This multi-input power supply buck-boost converter fits on top of a Raspberry Pi (any sort!) and lets you power it with up to 3 different input ports, so you can keep powered no matter what your battery or power plug situation. Note that although it has the name...

This is the 16mm 10MP Telephoto Lens, an essential for the Raspberry Pi High Quality Camera. It has a wide field of view and a variety of uses, like CCTV applications, or of course, cat photos. Telephoto lenses are great for distance shots - especially good when you need to take photos or videos of far away cats. Includes a thumbscrew to quickly and easily assemble...

Mary Poppins had her TARDIS-like carpet bag. 90s kids had their Pokémon card binders. But we have the next best thing: microSD and SD Card Holder, a super-slim 8-piece microSD storage card. The most useful thing you didn't know you needed. Each order contains one holder that can keep 2 x full sized SD cards plus 4 x microSD cards. If you're working with single...

This is a mouse. A nice, simple mouse. No bells or whistles. Just a mouse. But that doesn't mean it's not the best simple mouse! We compared a few and liked this one quite a bit. It's optical for good resolution and precision, has two buttons for use with any kind of OS, and has a pretty sturdy USB connector. The track wheel has a good spin and click action. The...

The quick brown fox jumps over the lazy dog. The quick brown fox jumps over the lazy dog. The quick brown fox - sorry! We were practicing our typing ON THIS AWESOME KEYBOARD. With slim chiclet keys, this 'normal size' keyboard is the perfect on-the-go accessory to your Pi, BeagleBone, or everyday computer. There's also a trackpad on the right hand side with support...

With any Raspberry Pi project you may reach a step that involves putting our products in out-of-the-way locations, where they act as a bridge between the network and the physical world. But the more out-of-the-way the location, the more challenging it is to get power. PoE offers one solution to this problem, allowing you to send power from Power Sourcing Equipment...

Add a good quality, slim keyboard to your Raspberry Pi, Beagle Bone Black or other mini-computer with this sleek black chiclet keyboard. It's a full QWERTY keyboard with a wireless USB dongle and is compatible with all operating systems. We tried many keyboards to find one that felt good for every-day use and didn't take up too much room. While it's not as small as...

"'There is one who may claim it by right. For this assuredly is the palantír of Orthanc from the treasury of Elendil, set here by the Kings of Gondor. Now my hour draws near. I will take it.'" –Aragorn II Elessar This magnificently Glowing Trackball has the positive qualities of a palantír: communicate with one another across vast distances,...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero, Bonnet, HAT or pHAT. Make sure to carefully read...

We love the Raspberry Pi 4 and 5, with their fancy new USB Type C power connectors. Now we have an even better power supply that can be used with either a Pi 4 or even a Pi 5 with 5V output and 4 Amps of current to handle builds with accessories and displays. This flat square body works best when plugging into a wall socket so it doesn't get knocked out easily, and a...

The official Raspberry Pi PD USB-C power supply is here! Superfast with just the right amount of cable length to get your Pi 5 projects up and running! With true Power Delivery support, this supply can easily supply 5 A of current! Comes in gothy Adafruit Black! Great for use with Pi 4 or Pi 5 Features: AC 100-240V 50/60Hz input with US plugs. DC 5.1V 5A output. 27W...

We love the Raspberry Pi 4 and 5, with their fancy new USB Type C power connectors. Now we have an even better power supply that can be used with either Pi 4 or even a Pi 5 with 5V output, 3A of current to handle builds with accessories and displays. The vertical-style plug wont take up extra ports on your power strip, and the handy on/off switch at the end will cut...

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit Mini PiTFT - 135x240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color...

Optimise data transfer speeds on your Raspberry Pi computer with an official Raspberry Pi 64GB microSD card. Rigorously tested to ensure optimal performance on Raspberry Pi computers, these Class A2 microSD cards help ensure you get the smoothest user experience from your device. Pre-formatted to FAT32, so it works out of the packaging with our projects. Ideal for...

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit Mini PiTFT - 1.3" 240x240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color...

Unlock ultimate performance for I/O intensive applications on Raspberry Pi 5 with a Raspberry Pi NVMe SSD. These SSD drives are specified by the Pi Foundation to have the best performance-for-price, and will work perfectly with any M.2 HAT or adapter (we stock many varieties). Features: 512GB capacity. High-performance Raspberry Pi NVMe SSD capable of:50k IOPS* (4kb...

One can never have enough socks, or USB ports. Add some more USB and Ethernet capability to your Raspberry Pi Zero or, really, any kind of tablet or computer with an OTG connector with this USB 2.0 and Ethernet Hub! This handy combo-hub has 3 USB 2.0 ports, and a AX88772A Ethernet transceiver. This chipset is really common and can be used by any Linux, Mac or Windows...

Sure, you have a keyboard. Maybe it's wireless. Maybe it's even Bluetooth®. But do you have a mini Bluetooth® keyboard? Like Halloween candy, this keyboard is fun-size! If Shakespeare had this wee chiclet keyboard back in the day, he definitely would've remarked, "And though it be but little, it is fierce!" We got one of these with a DIY 'tele-prompter' kit...

This Antenna Kit is made and certified specifically for the Raspberry Pi Compute Module 4's with WiFi - to get better range, especially when the CM4 is in an enclosure! Fitting Instructions Connect the MHF1 connector on the cable to the MHF connector on the Compute Module 4. Screw the toothed washer onto the SMA (male) connector on the cable. then insert this SMA...

This is a mouse. But, hark, it's no generic mouse. It's the Official Raspberry Pi Mouse! It's optical for good resolution and precision, three buttons, and has a sturdy USB connector. The track wheel has a good spin and click action. The right and left click also make a nice satisfying sound which we always enjoy. It's small, but not too small, yet big enough to fit...

Adding shortening to a pie makes it fatter - but this kind of shortening makes your Raspberry Pi a little slimmer! These short-style microSD adapters slide right into the SD card slot, but are 9mm shorter than a standard card. Upgrade to one of these and your Pi will be sleeker, elegant and a lot less accident prone. We have these in green, blue, pink, and black!...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black with the Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

One can never have enough socks or USB ports. Add some more USB and Ethernet capability to your Raspberry Pi or, really, any kind of computer with this USB 2.0 and Ethernet Hub! This handy combo-hub has 3 USB 2.0 ports and an AX88760 Ethernet transceiver. This chipset is really common and can be used by any Linux, Mac, or Windows computer. It's particularly handy for...

One can never have enough socks, or USB ports. Add some more USB and WifI capability to your Raspberry Pi or, really, any kind of computer with this USB 2.0 and WiFi Hub! This handy combo-hub has 3 USB 2.0 ports, and an RTL8188EU WiFi transceiver. This chipset is really common and can be used by any Linux, Mac or Windows computer. It's particularly handy for the...

We love the Raspberry Pi 4 and 5, with their fancy new USB Type C power connectors. Now we have an even better power supply that can be used with either Pi 4 or even a Pi 5 with 5V output, 3A of current to handle builds with accessories and displays. This flat square body works best when plugging into a wall socket so it doesn't get knocked out easily, and a handy...

An affordable, simple solution to mounting a Raspberry Pi Zero to your HQ Camera. Easy to assemble, the plate attaches to your HQ Camera on one side, and your Pi Zero mounts to the other side – spacers and fixings are included in the pack. Comes in Adafruit black and features a bubble level for that perfectly aligned shot, plus a handy thumb section for easy...

Add speedy mega-storage in a jiffy using this 16 GB Class 10 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters! Preformatted to FAT so it works out of the box with our projects. Works great with any device in the Adafruit shop that uses micro-SD cards. Ideal for use with Raspberry Pi, BeagleBone Black and other...

Add a rolling interface with your project with this Panel Mount USB Trackball with Three Buttons that is super easy to use and interface with. Simply plug it into your computer (desktop of single-board-linux type), it will appear as an external mouse with left and right buttons plus a middle button. Perfect for use with an embedded computer setup that needs a pointer...

Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi and Beagle Bone's USB port to add a low cost, but high-reliability wireless link. We tried half a dozen modules to find one that works well with the Pi and Bone without the need of recompiling any kernels: its supported by the Bone's Angstrom/Debian installation that...

Adding shortening to a Pi makes it fatter - but this kind of shortening makes your Pi a little slimmer! This short-style blue microSD adapter slides in where the SD card goes but is 9mm shorter. This makes it stick out a lot less and makes for a more elegant (and less accident-prone) Pi. All you have to do is pop in a microSD card for a sleeker machine! The outer...

Adding shortening to a Pi makes it fatter - but this kind of shortening makes your Pi a little slimmer! This black short-style microSD adapter slides in where the SD card goes but is 9mm shorter. This makes it stick out a lot less and makes for a more elegant (and less accident-prone) Pi. All you have to do is pop in a microSD card for a sleeker machine! The outer...

The IRKey adds an IR remote receiver to any computer, laptop, tablet...any computer with a USB port. This little board slides into any USB A port, and shows up as an every-day USB keyboard. The onboard ATiny85 microcontroller listens for IR remote signals and converts them to keypresses. We bundle this with our remote with 21 buttons so it controls nearly anything...

Give your Pi some reach with this GPIO extender cable, which has two matching connectors on the end of a 12" (300mm) long gray cable. Plug one end into your Pi and the other end will have a boxed male header you can plug in a Pi Plate that is expecting to go onto a Pi. This cable is not compatible with the Raspberry Pi Model B+ Please note! Some electronics do not...

Adding shortening to a Pi makes it fatter - but this kind of shortening makes your Pi a little slimmer! This green short-style microSD adapter slides in where the SD card goes but is 9mm shorter. This makes it stick out a lot less and makes for a more elegant (and less accident-prone) Pi. All you have to do is pop in a microSD card for a sleeker machine! The outer...

Adding shortening to a Pi makes it fatter - but this kind of shortening makes your Pi a little slimmer! This short-style, pink microSD adapter slides in where the SD card goes but is 9mm shorter. This makes it stick out a lot less and makes for a more elegant (and less accident-prone) Pi. All you have to do is pop in a microSD card for a sleeker machine! The outer...

AstroPrint is free, open source software for wirelessly managing 3D printers. It features a mobile friendly user interface that works across multiple devices and screen resolutions. This makes 3D printing easier to manage, eliminating the need for SD cards or manually controlling via USB. Astroprint also works in the cloud, so you can manage prints anywhere through a...

Extra-long and bendy, this is just like your classic Model A or B Pi GPIO cable but 12" (300mm) long and fitted through a tube so that it's a little more flexible in all directions. This cable is not compatible with the Raspberry Pi Model B+ Please note: These cables come with strain-relief clips that make the connector a bit taller than 'classic' GPIO cables. If you...

Adafruit picked these bags for kids (and those of us who are still kids on the inside) to tote their Raspberry Pi projects! They're high quality bubble-textured totes in a red raspberry color. Made by MadPax through an embossing construction process which yields a tough but soft bubbly exterior. This bag has a hang loop on top and comes with a shoulder strap. Red...

[Raspberrypi] A high-power, reliable, USB 2.0 hub ideal for the Raspberry Pi® Fast, Fiesty and Fruity - Comes with a US-plug 5V 3A power supply, plenty of power for your big Pi projects! Tested & endorsed by the Raspberry Pi Foundation! Small enough to fit in your pocket but with enough power to charge mobile phones, run hard drives and other power-hungry...

A massive rechargeable battery pack for your Raspberry Pi (or Arduino, or Propeller, or anything else that uses 5V!). This pack is intended for providing a lot of power to an iPhone, cell phone, tablet, etc but we found it does a really good job of powering other miniature computers and micro-controllers. Inside is a 3300mAh lithium polymer battery, a charging...

The Raspberry Pi open source laptop that you've been waiting for has arrived with the Pi-Top! With this kit you can build your very own "laptop" which at it's core runs off of the famous Raspberry Pi. The laptop case comes with a screen, base top, base bottom, and the Pi-Top Hub PCB to take care of power management, the screen driver, and more for you. Raspberry Pi...

Discontinued - you can grab this Mini Remote Control instead! OSMC is a free and open source media player based on Linux. We love the OSMC RF Remote Control for a Raspberry Pi media center. Each button on this remote is mapped to a unique function within OSMC. The USB receiver makes installation a snap and serves as the receiver for the remote. The RF design means no...

The Raspberry Pi open source laptop that you've been waiting for has arrived with the Pi-Top! With this kit you can build your very own "laptop" which at it's core runs off of the famous Raspberry Pi. This is the GREY Pi-Top! The green version can be found here. The laptop case comes with a screen, base top, base bottom, and the Pi-Top Hub PCB to take care of power...

The pIRkey adds an IR remote receiver to any computer, laptop, tablet...any computer or device with a USB port that can use a keyboard. This little board slides into any USB A port, and shows up as an every-day USB keyboard. The onboard ATSAMD21 microcontroller listens for IR remote signals and converts them to keypresses, mouse movements, or even USB serial output....

This nifty little plastic tool provides you a super simple, super cheap means for adjusting the lens of your Raspberry Pi camera! Simply place the little hole opening snugly over the camera lens – it should set nicely with no need to force. Then turn like a dial to the left or right and adjust the focus to your heart's content! For use with the Raspberry Pi 8MP...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero or pHAT/bonnet/HAT. Make sure to carefully read...

Discontinued - you can grab Raspberry Pi 400 Desktop - Full Computer Kit instead! The Raspberry Pi open-source laptop that you've been waiting for has arrived with the pi-top v2! With this kit you can unleash your inner inventor to create projects and explore technology while using the famous Raspberry Pi. pi-top strives to inspire inventors and creators to seek the...

The Andrea Superbeam Array-PA Microphone is a far-field, 2-microphone array with stereo output and superior quality and performance, designed for hearing and recognizing voices even in noisy environments. We tested it here in the Adafruit factory and it did a great job picking up our voice commands even when the machines were all running. The microphone is designed...

Zero Stem? More like, full stream ahead! This is a neat little PCB shim that transforms your Raspberry Pi Zero into a USB dongle! Super handy when you want to share your computer's Internet connection without messing with extraneous adapters, cables, what have you. Works great with our USB Gadget for Raspberry Pi Zero guide. Once soldered on, the Stem lets you plug...

Looking for another way to keep your Raspberry Pi cool? Hook up Pimoroni's miniature 5V Fan SHIM and prevent your hard-working Pi from overheating! It'll keep your Pi running at top performance and it's stealthy-silent. The software will turn on the fan only when necessary, and has an RGB LED status indicator as well. Designed for use with the high-power Raspberry Pi...

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. This version includes one piece of male header along with some crafty little retaining nubbins to grip tightly into the holes on the PCB. If you need both male and female headers, check out this version!...

We originally stocked these cables for the Raspberry Pi Model A or B computer, but then the B+ and beyond came out and those all have 2x20 pins. So now we've got a ton of these cables just sittin' around. And we wanted to clear out some space for more NEW goodies, so they're going on the clearance rack! Even if you don't have a Pi, these are great ribbon cables, in...

If this keyboard doesn't catch your eye, we don't know what will! It's cool, it's colorful, and it's clicky in the best way, and it'll make you feel like you're operating some kind of retro-futuristic typewriter. It's the Keyboard with Blue-type Mechanical Switches and LED Backlights! With 87 keys and rows that are backlit by LEDs, you'll be hacking, coding and...

Add a slim, lightweight Bluetooth keyboard that is neither too big, nor too small for your computer project! We've found the "just right" Goldilocks-size keyboard, a mere 9.6" x 5.8" x 0.2"! This keyboard has helpful indicator lights for Caps Lock, Bluetooth, Charge, and Power. It makes a great typing interface for a computer, especially for tablets, phones, boards...

We're carrying the Official Raspberry Pi Keyboard! It includes a USB hub with 3 built-in ports (which frees up the USB ports on your Pi! It's a peripheral party!). The keyboard is a full QWERTY keyboard and is compatible with all operating systems. While we love grab-bag, mixed, and assorted things, sometimes it's rather nice to have a matching set of keyboard and...

Discontinued - you can grab this Adafruit MacroPad RP2040 Starter Kit - 3x4 Keys + Encoder + OLED - ADABOX019 Essentials instead! Glow up for keyboards! Pimoroni's Keybow is a solderless mini mechanical keyboard with super satisfying high-quality clicky switches. The per-key RGB lighting shines brilliantly through the clear DSA-profile key caps, so you get all the...

Add a cool touch interface with your project with this Panel Mount USB Trackpad with Three Buttons that is super easy to use and interface with. Simply plug it into your computer (desktop of single-board-linux type), it will appear as an external mouse with left and right buttons plus a middle button. These look like they're laptop replacement parts, but we're not...

Add a cool touch interface with your project with this Panel Mount USB Trackpad with Two Buttons that is super easy to use and interface with. Simply plug it into your computer (desktop of single-board-linux type), it will appear as an external HID trackpad with left and right buttons. Perfect for use with an embedded computer setup that needs a pointer but you don't...

Make your Pi a little slimmer with this microSD card adapter board. It slides in where the SD card goes but is half the length. Pop in a microSD card for a sleeker machine. The microSD card holder is a push-push type so you can push on the edge that sticks out to remove the card when necessary. MicroSD card and Raspberry Pi NOT INCLUDED. Depending on the case from...

Add mega-storage in a jiffy using this 8 GB micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters! Preformatted to FAT so it works out of the box with our projects. Tested and works great with our Wave shield, Data logger shield and GPS shield, and micro-SD adapter as well as any other device in the Adafruit shop that uses...

Mary Poppins had her TARDIS-like carpet bag. 90s kids had their Pokémon card binders. But we have the next best thing: DiMeCard, a super-slim 8-piece microSD storage card. The most useful thing you didn't know you needed. If you're working with single board computers like the Raspberry Pi or BeagleBone - or maybe you're doing a lot of datalogging or...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Like the Raspberry Pi and want to support the Raspberry Pi foundation? All while looking good at it? Adafruit now carries the Official Raspberry Pi shirts! In Adafruit black The Raspberry Pi logo proudly displayed on this classic black t-shirt. This is a high quality heavy cotton t-shirt with a beautifully screen-printed full colour Raspberry Pi logo. 100% Heavy...

Add lots more USB capability to your Raspberry Pi or computer using this powered USB 2.0 hub. It adds a full seven powered ports, all at USB 2.0 speeds so you can use video cameras and other high speed devices (cheaper hubs are v1.1 and not as fast!) The extra sauce with this hub is that you can power it with an external 5V adapter. There's a 2 Amp adapter included,...

Discontinued - you can grab USB WiFi (802.11b/g/n) Module: For Raspberry Pi and more instead! Make your Internet of Things device cable-free by adding super WiFi. Take advantage of the Raspberry Pi and Beagle Bone's USB port to add a low cost, but high-reliability wireless link. We tried half a dozen modules to find ones that work well with the Pi and Bone without...

This cute little dongle is perfect for making your Raspberry Pi cable-free by adding WiFi. Take advantage of the Raspberry Pi's USB port to add a low cost, but high-reliability wireless link. You'll have wireless Internet in 10 minutes! Works great with 802.11b/g/n networks. This is the official Raspberry Pi foundation version, for use with the most recent Raspberry...

This cute little dongle is perfect for making your Raspberry Pi cable-free by adding WiFi. Take advantage of the Raspberry Pi's USB port to add a low cost, but high-reliability wireless link. You'll have wireless Internet in 10 minutes! Works great with 802.11b/g/n networks. This module is supported by Windows 10 IoT (october 2015 release or later) - available now on...