Raspberry Pi / Cables

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 24" / 610mm long We have cables in 2", 4", 8", 12", and 18" long so you can have the perfect fit. Each order comes with one cable, Pi...

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two #4-40 screws are used to attach the female socket end, 26.9mm apart. Two hex-body standoff-screws are included as shown above and the hex nuts are embedded inside the molded end. Cable is 40cm long (about 16 inches). This is a HDMI 1.4 cable.

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics, they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails. This cable is not compatible with the Raspberry Pi Model B or Model A! If...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display, for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 300mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 1 meter long. We have cables in a ton of sizes so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 200mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in...

Every time someone posts on the Adafruit forums and says they need to have a really long cable for their Pi Camera (CSI) or Pi Display (DSI), we say, "Oh you mean like some sort of CSI/DSI cable extender thingy? Yeah we don't have one of those in stock yet" But that time is over! Now we can say, "Yes we have a CSI/DSI Cable Extender Thing y in stock!" And we point them here. This Thingy is very simple, it lets you connect...

Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 2 meter long (about 6 feet). This is a HDMI 1.3 cable. Works great with a BeagleBone or Raspberry Pi 4 Micro HDMI to HDMI Cable - 2 meter (0:47)

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 2 meters long. We have cables in a ton of sizes so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but...

Connect two HDMI devices together and save space with this basic flat HDMI 1.4 cable. It has nice molded grips for easy installation, and is 1 foot long (~30 cm). This cable is absolutely  perfect  for an LCD Raspberry Pi project. The cable is so thin and flexible that you won't have any loose dangling HDMI cables getting in the way, and you can even fit your Pi behind the screen.

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable ! Comes in a classic Adafruit Black, has a nice soft flexible 16-line 0.05" ribbon cable and keyed IDC connectors on both ends. It's perfect for use with our GPIO Expander bonnet or with any of our RGB LED Matrices if you want to chain them together or extend the cable a little farther This cable is 12" long and...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 18" / 457mm long We have cables in 2", 4", 8", 12", and 24" long so you can have the perfect fit. Each order comes with one cable, Pi...

"Is it not a strange fate that we should suffer so much fear and doubt for so small a thing? So small a thing!!" – Boromir , The Lord of the Rings That Raspberry Pi camera or display (CSI/DSI) connectors can sometimes get damaged, and it would be a shame to have to toss the whole thing! Maybe you got a little over-enthusiastic and She-Hulk'd out on the connector arms and broke it. We understand, it happens! Here's a...

This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in another USB device. For example, a Pi Zero or Pi Zero W has a OTG port, as does the Arduino Zero, and anything with an ATSAMD21 that is in USB host mode. Also great for when you want to attach to a tablet or phone with an OTG...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0, but with a twist! Literally! Instead of the cable coming straight out from the connector, there's a right angle bend. We thought this might make a good pair for a Raspberry Pi Model A or B as the cable doesn't stick out as far. We got cables with extra-beefy 24 AWG power wires, and 28 AWG data lines, so it's particularly good for power-hungry devices like...

ON...off...ON...off...ON...off...ON...off...WE CAN'T STOP CLICKING THIS ON-OFF SWITCH! It has such a satisfying click and it works so well.  Plus, it's just about perfect for charging your Raspberry Pi - either Model B, A+, B+, or Pi 2.  Just hook up the standard USB end to a 5V 1A USB port power supply or 5V 2A USB port power supply and the Micro B end to a Raspberry Pi and you have a Pi with a switch. This...

This A/V RCA Cable for Raspberry Pi is a great way to turn your Pi 3, 2, A+ or B+'s output into a full on composite video and audio device.  Simply connect the cable to your Raspberry Pi's 3.5mm jack and the other side into whatever device you're looking to connect to and get full RCA visuals and sound. We're big fans of RCA connectors.  They're one of our favorite plugs that everyone has a fond memory of using....

Use this 25 cm long cable with our 40-pin FPC to 2x20 IDC Plug and Socket adapter PCBs to extend your Raspberry Pi's GPIO capabilities. Note you'll have to keep an eye on where Pin 1 is on the ribbon cable, on the adapter PCBs, and your HAT or Bonnet of choice. Works great with any two of the following: 40-pin FPC to Straight 2x20 IDC Male Plug Header40-pin FPC to Right Angle 2x20 IDC Male Plug Header Adapter40-pin...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 100mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in...

That new Raspberry Pi 400 computer you just got has a row of 2x20 pin headers on the right side - those are the GPIO (general purpose input/output) pins, and for those of us who like to hack electronics, they are where the real fun lies. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails. Unlike the 'classic' Raspberry Pi computers, you can't really...

Do you have a S-Video display, projector or monitor that is not compatible with your HDMI devices? Here's an adapter that will allow you to convert HDMI to S-Video, for older video devices that might not have an HDMI input. S-Video has better performance than plain "RCA" composite NTSC/PAL as it separates the color and light level, so if you have a device that can take either S-Video or NTSC/PAL composite, you're better...

We're now stocking a very fancy Official Raspberry Pi Micro HDMI to HDMI cable with overmolding and Pi logo! It has nice molded grips for easy installation, and is 1 meter long. Perfect for use with your new Raspberry Pi 4 and playing with dual screen setup (you'll need one per Micro HDMI port) Please note that these molded connectors are a little chunkier than many classic HDMI cables.  

This is your standard USB A-Plug to Micro-USB cable. It's 2 meters long so you'll have plenty of cord to work with for those longer extensions.  Perfect for connecting to your Raspberry Pi, Arduino Leonardo/Micro, FONA or Trinket (among other things). It's got extra beefy 24 AWG power wires so it works great for high power (1-2 Amp) computer powering. If you want something a little shorter, check out our 3'...

Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 3.5mm Stereo Plug. It's a pretty common size and is super useful in most headphones or basic audio...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 50mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in...

Connect two HDMI devices together and save space with this slim, high quality HDMI cable. It has nice molded grips for easy installation and is 450mm long (~1.5 feet). Sporting a teeny 4mm diameter this cable stays out of your way! We also have slim HDMI cables at 914mm long and 1820mm long.

This handy Panel Mount RCA Cable is perfect for component/composite video and audio and perfect for connecting our Raspberry Pi to RCA component/composite screens. This cable comes with two nice RCA connectors and has two mounting screws 20mm apart. The cable is 264mm / 10.4" long.

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a 40-pin FPC to Straight 2x20 IDC Female Socket Header Adapter Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply plug the socket side into the Raspberry Pi. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the 40-pin flex connector. You can use any 40-pin 0.5mm FPC...

Oof - you got a Raspberry Pi Model A+ or B+ that you want to have work with some old kit or plate or breakout or something and it uses the classic 26-pinout. Very frustrating, it is...unless you have this ingenious 'downgrade' GPIO cable. It has a 40-pin socket on one end, but only the first 26 pins have a cable and the other end matches any sort of Cobbler or PermaPi or what-have-you. Cable is 6" long, and pin #1 is marked with a...

Connect two HDMI devices together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1 meter long (about 3 feet). This is a HDMI 1.3 cable. We're now stocking a very fancy Official Raspberry Pi cable with overmolding and a Pi logo. Please note that these molded connectors are a little chunkier than classic HDMI cables  

This basic cable comes with two 3.5mm (1/8" headphone jack size) stereo connectors. It's fairly straight forward, you'll commonly need these to connect two audio devices together. Cable is 6 ft long.

Do you have a display, television, projector or some other older device that isn't compatible with your HDMI devices? Here's an adapter that will allow you to convert HDMI from your modern computer or game system to NTSC/PAL, for older screens and devices that might not have an HDMI input. This mini HDMI to AV signal converter will convert HDMI video signal or audio signal to CVBS (either NTSC or PAL selectable) composite video...

This 50-pin FFC / FPC Extender is very simple. It lets you connect two 50-pin 0.5mm pitch FFC (Flexible Flat Cable) / FPC (Flexible Printed Circuit) cables end-to-end and extend the length. Note that pin 1 of one cable is connected to pin 50 of the other so you need to use a cable that has contacts on the same side (type A cable) Carefully pry the two ears of the connectors, plug the cables with contacts pointing up, and then push the ears...

Connect two HDMI devices together and save space with this slim, high quality HDMI cable. It has nice molded grips for easy installation and is 1820mm long (~6 feet). Sporting a teeny 4mm diameter this cable stays out of your way! We also have slim HDMI cables at 450mm long and 914mm long.

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a  40-pin FPC to Right Angle 2x20 IDC Female Socket Header  Adapter Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply plug the socket side into the Raspberry Pi. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the 40-pin flex connector. You can use...

That new Raspberry Pi® Model A or B computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails. This cable is not compatible with the Raspberry Pi Model B+ If you want...

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a  40-pin FPC to Straight 2x20 IDC Male Plug Header  Adapter Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply insert the plug side into an optional Socket Riser Header to add to the HAT or Bonnet. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the...

Your cell phone charges off of USB, but can you really trust that charging station at the airport? Now you can control when to allow data in or out of your device with this little USB extension cable. You can plug it onto the end of any USB data/sync cable you have: mini-USB, micro-USB, Apple Lightning, or any other proprietary type. Voila! Your cable's data lines can now be switched on or off. Not only is it great for privacy and security...

If you have a computer or tablet or device with HDMI output but you want to connect it to a projector, monitor or display with VGA input, you have come to the right place! This nifty adapter cable has a classic HDMI plug connector at one end and at the other end a DB-15 VGA connector (it has hex nuts that you can remove if you are trying to mate it with a cable that also has hex nuts). There's also an audio jack on the side, this provides...

Connect two HDMI devices together and save space with this slim, high quality HDMI cable. It has nice molded grips for easy installation and is 914mm long (~3 feet). Sporting a teeny 4mm diameter this cable stays out of your way! We also have slim HDMI cables at 450mm long and 1820mm long.

Do you have an an older VGA-output computer, game system, or other device, that you want to hook up to your fancy new HDMI monitor? This converter will take a VGA signal and convert it to every-day HDMI so it will work with your computer monitor, display, television, projector, etc. This high-definition video converter will convert analog stereo audio signal and analog RGBHV from the DB-15 plug and combine them together into digital HDMI...

Seamlessly transmit high-quality stereo audio with this  3.5mm Male/Male Stereo Cable.  Ideal for "passing the AUX cord," or connecting audio devices such as smartphones, tablets, MP3 players, car stereos, portable speakers or any other 3.5mm (otherwise known as "1/8 inch") outputs.

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a 40-pin FPC to Right Angle 2x20 IDC Male Plug Header Adapter. Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply insert the plug side into an optional Socket Riser Header to add to the HAT or Bonnet. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the 40-pin flex...

This is a nice solution to wanting to use PS/2 devices (such as our capacitive touch pad or magstripe readers). It's also handy if you want to connect a keyboard and mouse to a Raspberry Pi or Beagle Bone without taking up two USB ports. Inside is a full translation chip - a small USB microcontroller that will translate the PS/2 into "USB Keyboard" and "USB Mouse" We tested this with a Pi, Bone, Linux, Windows and Mac...

If you have a computer or tablet or device with Mini HDMI output but you want to connect it to a projector, monitor or display with VGA input, you have come to the right place! This nifty adapter cable has a Mini HDMI plug connector at one end and at the other end a DB-15 VGA connector (it has hex nuts that you can remove if you are trying to mate it with a cable that also has hex nuts). There's also an audio jack on the side, this provides...

At first glance this appears to be an ordinary A to micro B USB cable. Plug it in to your device and power supply, and you get a colorful glitter of dozens of little LEDs embedded in the length of the cable. Can be used for data and charging. The LEDs are luminous but not  too  bright. Perfect for vampire makers, candy ravers, or maybe night owls who misplace their devices in the thick of night!

At first glance this appears to be an ordinary A to micro B USB cable. Plug it in to your device and power supply, and you get a colorful glitter of dozens of little LEDs embedded in the length of the cable. Can be used for data and charging. The LEDs are luminous but not too bright. Perfect for vampire makers, candy ravers, or maybe night owls who misplace their devices in the thick of night!

Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 3.5mm TRRS Plug with four poles. TRRS stands for Tip, Ring, Ring, Sleeve. It has four total conductors -...

Here is a gorgeous metal-covered audio cable straight from Blade Runner/cyberpunk heaven. And we have them in a couple different colors! They're a step up from plain rubber/ABS cables, with a sleek metal-wound cover. This cable comes with two 3.5mm (1/8" headphone jack size) stereo connectors. Fairly straight forward, you'll commonly need these to connect two audio devices together, whether it's a NeoTrellis project or...

Is the flex cable for your Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display too short? Or maybe it's cluttering your workspace, and you want something more compact.  Whatever your Pi Camera needs, we have a variety of cable lengths for your Raspberry Pi Camera Board or Raspberry Pi NoIR Camera Board. They're super easy to install - just open the connector on the Pi and slip one in....

Give your Pi some reach with this GPIO extender cable, which has two matching connectors on the end of a 12" (300mm) long gray cable. Plug one end into your Pi and the other end will have a boxed male header you can plug in a Pi Plate that is expecting to go onto a Pi. This cable is not compatible with the Raspberry Pi Model B+ Please note! Some electronics do not like having a 12" long cable involved where they are expecting a short...

Oooh it's so soft! And that beautiful pattern! If you have to have visible cables then you might as well have the nicest fabric bound cable with a eye-catching snake-like pattern.  That's why we now carry this standard A to micro-B USB cable for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino Leonardo/Micro, Raspberry Pi, NETduino, (among other things). Basically: have something with a microUSB port? This...

This cable comes with two nice gold-plated RCA connectors. Perfect for use with component/composite video and audio, such as the YBox kit, Propeller Quick-proto for Quickstart board, and of course a Raspberry Pi® ! Cable is 6 ft long and has 75 ohm impedance.

One of the most common converter cables you'll want in your cable collection - this 6 foot long cable converts a standard 3.5mm stereo jack to two color-coded mono RCA coaxial jacks. You'll want this to convert a 'headphone' or 'line out' jack to your TV or stereo audio in panel. Perfect for use with component/composite video and audio, such as the Raspberry Pi® ! Cable is 6 ft long.

This coupler is kind of like a really short RCA cable. We think its perfect for use with our NTSC/PAL displays since they already have a cable. So instead of a long cable from the display to something like the Raspberry Pi, just pop one of these in between!

Do you have an older electronic device that isn't compatible with your HDMI equipment? Here's an adapter that will allow you to convert your older composite AV-output devices on modern TVs and monitors. Perfect for reviving or re-using your older pieces of equipment that might not have an HDMI output (like an old computer or game system). This plug-and-play adapter takes 3-wire composite input: NTSC or PAL video on...