Cables / Cable Assemblies

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming apart...

This product is a 3-in-1 cable. By itself, it can act as an extension cord for any 5.5/2.1mm DC power cable. The heavy 24 AWG wires can handle up to 5A. You can also cut it half to make two barrel cables (one plug and one jack). This will allow you to connect a classic 'wall wart' to a breadboard or PCB without having to solder in a bulky power jack. Or you can use...

By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in...

Outdoor enthusiasts rejoice! We now have very useful 4-wire polarized cable sets in a waterproof variety. These cable sets are ideal for projects that must weather the weather: dust, water, rain, snow, tornado (not volcano proof!). Each cable has 4 color-coded conductors (red, black, white yellow) that match between the sides, for easy wiring and connectors are...

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in the middle, try this switched extension cable. Finally, for PCB and breadboard...

These little cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits, and have a few handy in our ARM-dev box. We thought you may want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is...

You'll find these handy 2-pin 0.1" spacing pig-tails to be quite helpful when wiring up your project. The connector end snaps cleanly into 0.1" spaced header (and fits neatly side by side on 0.1" spacing as well). We think this would be especially useful when paired with our PWM driver breakout, to control 16 PWM LEDs that are wired, but there are probably a dozen...

Connect this to that with an IDC cable! This cable has 6 pins (2x3) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto either side, they're quite sturdy!

We don't really know what to call this thing - it's got a 10 pin IDC cable on one end 6 inches of rainbow ribbon and tipped with 0.1" female socket connectors on the ends. We think this would be handy as a 10-pin JTAG breakout adapter, or maybe some sort of cable re-arranger. Anyhow, it seems useful and we picked up a bunch. Yeah we know it would be awesome if we...

For big projects, with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. Only problem is that these supplies have connectors that only plug into motherboards or hard drives. That's where this cable comes in. It has a matching 4-pin molex connector to the hard drive/CD-ROM power cables that come out of a power supply so you can use this...

These 6-wire cables are 162mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 6 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

FPC cables are super thin and flexible. They're often used in electronics when a a round cable would be too bulky, especially if you're dealing with 50 contacts like this one! This cable has 50 pins, 0.5mm pitch, and is 250mm long. It pairs well with our 50 pin 0.5mm pitch breakout board. 50-pin 0.5mm Pitch FPC Flex Cable - 250mm / 10" long (14:35)

These 5-wire cables are 168mm (6.6") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 5 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from...

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers from one board to the other....

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can undo without tearing the contacts from the housing. Plugs in nicely all with our...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board...

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together! This is an A-A cable, that...

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

We now have a handy extension cord for JST-XH projects! One end has a JST-XH socket, and the other has a matching plug. Between the two, 500mm of color-coded wire. This solid 2.5mm pitch connector extension cable is great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. The two...

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to match up with our STEMMA boards and sensors that have 3-pin connections - and the wires are even color coded! Red is power,...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with male socket headers on the end For more information about JST PH...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and STEMMA JST PH connectors on the other. You can sand down the center-nub key on the JST PH side to make it fit in a Grove connector. Chunkier JST PH connectors come with 2mm pitch, and JST SH (also...

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Has a nice soft flexible 20-line 0.05" ribbon cable and keyed IDC connectors. Good for JTAG connections, in particular - but is useful for anything really. This cable is 12" long and has 20 pins (2x10) in 0.1" x 0.1" spacing and two sockets crimped on...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with female socket headers on the end For more information about JST PH...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has header pins, so it could be used to connect to socket...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits and have a few handy in our ARM dev box. We thought you might want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is 0.06mm/0.025"...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

If you'd like to make a connection to a board or breakout with Seeed Grove connection, this 100mm long 4-wire cable is fitted with a Grove connector and four bare wires. Please note you will have to watch for voltages on the power/signal pin when using 3V-only sensors, because Grove boards that are 5V logic like many Arduino UNO-compatibles. The colors are: Black for...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

Connect this to that when a 22-pin FPC connector is needed. This 20 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on one side will match with pin one on the other. How handy! We're stocking this to fit with the new Raspberry Pi 5 and our RP2350 boards with 22-pin HSTX connectors, but you could, of course, use it for anything that needs...

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers!...

If you're messing around with floppy drives, or disk drives, or other devices that are usually powered with a PC motherboard you'll often see these big 'Molex' connectors used to provide power. They are used to give 5V (red), 12V (yellow) and ground (black) and with this connector you can easily wire up your favorite power supply or bench-top power source. We also...

Connect this to that when a 24-pin FPC connector is needed. This 5 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as D style), which means that pin one on one side will match with pin one on the other side. How handy! We're stocking this to use with our e-Ink/e-Paper boards when they have 'flipped' connectors, but you could, of course,...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Comes in a classic Adafruit Black, has a nice soft flexible 16-line 0.05" ribbon cable and keyed IDC connectors on both ends. It's perfect for use with our GPIO Expander bonnet or with any of our RGB LED Matrices if you want to chain them together or...

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! We also carry the socket 'mating' version of this cable over here. For more information about JST PH connectors, visit the JST website

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy connections...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

When 0.1" is too big, and JST PH's too chunky, the ultra-slim "PicoBlade" is a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. This cable is nice and long, 200mm in fact. It's got both small form factor (won't take up a lot of real estate on your PCB) and friction lock to make easy-breezy connections to your HalloWing or anything...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 3-pin 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect...

When you need more distance between you and your eInk display, use this 24-pin 0.5mm pitch FPC cable with an extender adapter to streeeeeeeeeetch it out. The cable is generic, but we recommend it for use with eInk because often folks want to mount the displays elsewhere. Just carefully pry open the connector on the eInk Friend, eInk Feather Friend, etc, and use this...

Connect this to that when a 22-pin FPC connector is needed. This 5 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on one side will match with pin one on the other. How handy! We're stocking this to fit with the new Raspberry Pi 5 and our RP2350 boards with 22-pin HSTX connectors, but you could, of course, use it for anything that needs...

This cable will let you turn a JST PH 4-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND. Red for V+. White for SDA. Green for SCL. Even though this is a JST PH connector, it will fit into a Seeed Grove connector and...

This 9-pin cable is just about 100mm / 4" long and fitted with JST-SH female connectors on both ends. Compared with chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel and are easy to insert and remove. We got these especially for our fantastically spooky Adafruit MONSTER M4SK in case you'd like to split the mask in two and...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.187" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this...

Not to be confused with ODB, OBD stands for On Board Diagnostics and is used for analyzing and diagnosing vehicles. It's the thing your mechanic plugs into to find out why you've got a blinking engine light. Technically, OBD uses CAN bus and, hey, whaddya know, we've got some CAN-capable microcontroller boards here at Adafruit so this OBD Plug (16-pin) to DE-9 (DB-9)...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

Why are bananas never lonely? Because they hang around in bunches! A lot of power supplies, multimeters, and other benchtop equipment use standard 4mm banana plugs to connect this-to-that. When you need more, we now stock them! These are handy stackable and retractable Banana Plug cables! The retracting plastic protection bit on the end will automagically disappear...

Often used for floppy drives, 34 pin IDC cables have a 2x17 array of pins. This cable will let you connect one port to another with a festive rainbow design! Both ends have strain relief and keyed connectors. Perfect for retro archiving projects or whenever you have a 2x17 0.1" header on two sides of a board that need connecting.

Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for woven fabric cables. Like, peep this fully reversible pink/purple Blinka-inspired cable or this mithril-like 3-in-1 Sync and Charge cable. Our latest addition to the collection is this 1 meter long Black Magnetic USB A or USB C to USB C Cable with a Magnetic Type C tip!...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

Connect this to that when a 24-pin FPC connector is needed. This 10 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as D style), which means that pin one on one side will match with pin one on the other side. How handy! We're stocking this to use with our e-Ink/e-Paper boards when they have 'flipped' connectors, but you could, of...

Why are bananas never lonely? Because they hang around in bunches! A lot of power supplies, multimeters, and other benchtop equipment use standard 4mm banana plugs to connect this-to-that. When you need more, we now stock them! These are handy stackable and retractable Banana Plug cables! The retracting plastic protection bit on the end will automagically disappear...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

Connect this to that when a 24-pin FPC connector is needed. This 25 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as D style), which means that pin one on one side will match with pin one on the other side. How handy! We're stocking this to use with our e-Ink/e-Paper boards when they have 'flipped' connectors, but you could, of...

Stretch out your servo connections with this flexible servo to premium male header jumper cable. It has a 3-pin shrouded "male" connector to plug the servo into and then, 17cm later, three separated jumper wire ends that plug into a breadboard or some header. It's excellent for when you want to quickly and easily connect a servo to an existing dev board with sockets,...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on both ends - perfect for 'chaining' boards...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug/pin connectors on the...

For big projects with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. The only problem is that these supplies have connectors that only plug into motherboards or hard drives. That's where this cable comes in. It has a matching 4-pin Molex connector to the hard drive/CD-ROM power cables that come out of a power supply so you can use...

FPC cables are super thin and flexible. They're often used in electronics when a round cable would be too bulky, especially if you're dealing with 26 contacts like this one! This cable has 26 pins, 1mm pitch, and is 20cm long. We use it to connect to laptop floppy drives but you may have other uses for this cable! One could also cut it into a smaller number of pads...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy connections...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. Can also be used with any STEMMA breakouts! This cable has a JST PH 4-pin on one side and alligator clips on the...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

This product's about as simple as a cup of lemonade on a hot summer day. And, like lemonade, it's just three components! This board is a sewable adapter with a 3-pin JST wiring adapter. It's a perfect way to add a simple link between things like our Flora NeoPixels and more complicated products like our NeoPixel Rings. There are three holes on the board that are...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

Outdoor enthusiasts rejoice! We now have standard 5.5/2.1mm DC power cable sets in a waterproof variety. These cable sets are ideal for projects that must weather the weather: dust, water, rain, snow, tornado (not volcano proof!). They are a little bulkier than normal DC jacks because of the o-ring and removable over-screw. The o-ring is what makes the waterproof...

6" (150mm) long jumper cable of 6 conductors, 0.1" spacing with two 'female'/sockets on either end. Great for wiring up ShiftBrites together! Note: Wire colors may vary.

These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

Connect this to that with an IDC cable! This cable has 10 pins (2x5) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto either side, they're quite sturdy!

This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board to the other....

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and...

This cable is a little over 100mm / 4" long and fitted with JST-GH compatible 6-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily, and the wires are even color coded! These would go great with SEN54 or SEN55 all-in-one air quality sensor modules from Sensirion For more...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and a Grove connector on the other. This cable can be used with STEMMA or STEMMA QT / Qwiic boards to easily connect sensors and drivers from one board to the other. Please note you will have to watch for...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

Connect this to that when a 22-pin FPC connector is needed. This 10 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on one side will match with pin one on the other. How handy! We're stocking this to fit with the new Raspberry Pi 5 and our RP2350 boards with 22-pin HSTX connectors, but you could, of course, use it for anything that needs...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT 4-pin JST SH on one end, and Arduino MKR (ESLOV) 5-pin JST SH connectors on the other, with the wires spun around so you can use it to connect STEMMA QT sensors we've got to any of the popular Arduino MKR boards! JST SH (also known as Qwiic)...

Here's a handy power cable for the RGB LED Matrix Panels we carry. Easily plug into the back of your RGB matrix and insert or screw the power and ground cables onto either the Matrix Portal or the Matrix Bonnet, or whichever microcontroller-and-add-on you're using for your RGB Matrix project. Works with any/all RGB LED Matrices that are 'HUB75' style. Not for use...

Once in a while, we find products with center negative DC power jacks, and they really make us mad because who keeps around both positive and negative polarity versions of every voltage? Now, hopefully, USB Power Delivery will solve this long term, but until then, this 2.1mm DC polarity reversal adapter will have to do! Usage is simple: plug into any 2.1mm or 2.5mm /...

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug connectors on the...

These cables can be used with Qwiic or STEMMA QT boards to easily connect sensors and drivers from one board to the other. This variety of cables gives you the option of breadboarding with headers, using capacitive touch with alligator clips, and more. Compared with the chunkier JST-PH, these are 1mm pitch instead of 2mm, but still have a nice latching feel, while...

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

Ostensibly this extension cord was originally designed to allow PlayStation game players to be able to sit across the room from their game system, but what we are using it for is to connect to PS controllers and accessories without soldering directly to cables or cutting the connectors off. Since the connector is proprietary, it isn't like you can get a socket or...

This 2.5" SATA III to USB 3.0 Adapter Cable allows you to connect a standard 2.5" hard drive (HDD or SSD) to your computer. SATA III is like, a souped-up electronic energy drink, letting you backup files with a data rate up to 6Gbps. It's perfect for adding mega-amounts of storage to your single board computer, like a Raspberry Pi or BeagleBone. Simply plug the drive...

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards. This is the matching connector to the inverter. It is required to connect EL wire to the inverter! 0.1" (2.54mm) pitch...

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards. We use these mostly for EL wire. This is the same connector as is on the inverter. It's useful if you're making a...

Discontinued - you can grab Silicone Cover Stranded-Core Ribbon Cable - 4 Wires 1 Meter Long - 30 AWG Black instead! This supple, slippery silicone wire has 4 conductors, 24AWG each sealed in a full silicone casing. It's heavy duty so you can pass tons of current but soft and flexible so its good for wearables. We think this would be a good pair for our LED strips....

Connect this to that with an IDC cable! This cable has 10 pins (2x5) in 0.1"x0.1" spacing. This is a shorter version of the cable we've carried for AVR programming, we use this for chaining together 16x24 LED matrix panels or GertBots About 1.5" long with two sockets crimped onto either side, they're quite sturdy!

This cable product is no longer sold individually. We now only have them in set pairs for the same price! Get them here. This 4-wire cable is 20cm long and has a JST SM type connector receptacle on the end. It mates with the JST SM plug cable and is good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of...

Discontinued - you can grab Retractable Stacking Banana Plug Cable - Black 0.5 meter long instead! We're always digging around for various test lines to use with our power supply - whether we're checking current draw of our Feather, or trying out new LED samples. We picked up one of these and its so handy we use it all the time now. It's compact and has three of the...

The RockBLOCK 9603 Accessory Cable is terminated with a simple 10-pin Molex-style connector at one end and male jumper wires at the other. This accessory cable will help speed up your development time, meaning you no longer need to terminate and crimp your own connector for the RockBLOCK 9603. If you're going to connect the RockBLOCK 9603 to anything other than your...