Cables / Ethernet
-
Panel Mount Ethernet Extension Cable
Product ID: 909This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. We think this would be most useful when putting a Beagle Bone, Raspberry Pi, Arduino Ethernet into a box. The jack half has two mounting 'ears' with 4-40 screws installed, 1" inch / 25mm apart. The ears are flexible so the holes don't have to drilled very...$4.9533 in stock -
Cable Gland - Waterproof RJ-45 / Ethernet connector - RJ-45
Product ID: 827We have some great waterproof and weather-proof items in the adafruit shop, but once you have a project built, you'll want to enclose it. But how to keep an enclosure weather/waterproof while still attaching cables for power, data or sensors? That's where cable glands come in. By installing these over the cable, they form-fit to make a seal, keeping your project box...$7.95In stock -
Passive PoE Injector Cable Set
Product ID: 435Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a mess of wires. There is an official Power-over-Ethernet standard that allows devices and routers to...$5.95In stock -
RJ-45 Ethernet Round Panel Mount Extension Cable - 30cm
Product ID: 4215If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45 Ethernet Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your existing Ethernet kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or...$4.95In stock -
RJ-45 Ethernet Round Panel Mount Adapter Plug
Product ID: 4130If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45 Ethernet Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing Ethernet kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no...$5.95In stock -
PoE Splitter with MicroUSB Plug - Isolated 12W - 5V 2.4 Amp
Product ID: 3785Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different...$10.95In stock -
RJ-45 Terminal Block to Ethernet Socket Adapter
Product ID: 4981If you need to connect an RJ-45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet socket - this adapter will come in very handy! This is an Ethernet (RJ-45) Terminal Block to Socket Adapter. There is a standard RJ-45 Ethernet socket on one end and a terminal block on the other. No soldering required! Just unscrew the terminal blocks and slide in your...$6.9526 in stock -
802.3af PoE Output Data & Power Splitter - 12V 1A
Product ID: 3238Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one cable, and then separates the data (Ethernet) and power (+12VDC regulated) into two different...$9.95In stock -
PoE Splitter with USB Type C - 5V 2A - 100 MB Ethernet
Product ID: 4552Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different...$14.95In stock -
Skinny Ethernet LAN UTP CAT6 Cable - 3mm diameter - 30cm long
Product ID: 5443When you want a super skinny Ethernet / CAT-6 cable, this noodle-y UTP jumper is only 3mm thick at the center so that it can flex around enclosures easily. This cable is 30cm long, about one imperial foot, comes in Adafruit black. CAT6 means it's great for Ethernet-based LANs and other data networks. UTP means the wires are unshielded - much thinner but not great for...$2.50In stock -
5V 1.8A Isolated Output PoE Module - For Raspberry Pi 3 B+ or 4
Product ID: 3848Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! All you need is this handy PoE module, and access to the center-taps on your Ethernet-capable board. Attach the four input wires, and get regulated 5V 1.8A on the other side. Amazing! This version of the PoE module...$15.95In stock -
Ethernet RJ45 Male Plug Terminal Block
Product ID: 2913If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that with an Ethernet Jack - this adapter will come in very handy! No soldering required. Just use a slim screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire and re-tighten. Note that these aren't recommended for actual Ethernet traffic, especially long term...but for...$5.95In stock -
5V 1.5A Output PoE Module - Works with Raspberry Pi 3 B+ or Pi 4
Product ID: 3847Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! All you need is this handy PoE module, and access to the center-taps on your Ethernet-capable board. Attach the four input wires, and get regulated 5V 1.5A on the other side. Amazing! This module works well with the...$8.95In stock -
Ethernet RJ45 Female Socket Push-Terminal Block
Product ID: 2912If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet jack - this adapter will come in very handy! No soldering required. Just push the little buttons and slide in your stranded or solid-core wire. Note that these aren't recommended for actual Ethernet traffic, especially long term...but for basic power/data distribution,...$5.95In stock -
802.3af PoE Output Data & Power Splitter - 5/9/12V
Product ID: 3239Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one cable, and then separates the data (Ethernet) and power (+12VDC regulated) into two different...$24.95Out of stock -
Ethernet Cable - 10 ft long
Product ID: 730We have so many Internet-connected goodies in the shop, we figured it's time to carry a cable so you can easily connect them up! This cable is 10 feet long, black and has all 8 wires installed. Perfect for use with the BeagleBone, Arduino Uno Ethernet, Arduino Ethernet Shield, NETduino Plus, Patch Shield, PoE Injector cables, IoT Printer pack or any other...No longer stocked -
Ethernet Cable - 3 ft long
Product ID: 995We have so many Internet-connected goodies in the shop, we figured it's time to carry a cable so you can easily connect them up! This cable is 3 feet long, comes in Adafruit black and has all 8 wires installed. Perfect for use with the BeagleBone, Arduino Uno Ethernet, Arduino Ethernet Shield, NETduino Plus, Patch Shield, PoE Injector cables, IoT Printer pack or any...No longer stocked -
Ethernet Cable - 5 ft long
Product ID: 994We have so many Internet-connected goodies in the shop, we figured it's time to carry a cable so you can easily connect them up! This cable is 5 feet long, comes in Adafruit black and has all 8 wires installed. Perfect for use with the BeagleBone, Arduino Uno Ethernet, Arduino Ethernet Shield, NETduino Plus, Patch Shield, PoE Injector cables, IoT Printer pack or any...No longer stocked -
Skinny Ethernet LAN UTP CAT6 Cable - 3mm diameter - 1 meter long
Product ID: 5441When you want a super skinny Ethernet / CAT-6 cable, this noodle-y UTP jumper is only 3mm thick at the center, so it can flex around enclosures easily. This cable is 1 meter long, comes in Adafruit black. CAT6 means it's great for Ethernet-based LANs and other data networks. UTP means the wires are unshielded - much thinner but not great for ultra-long lengths (thats...No longer stocked