-
Product ID: 954
The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USBSerial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the...
-
Product ID: 70
Just about all electronics use TTL serial for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. This is a USB to TTL serial cable, with a FTDI FT232RL usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels....
-
Product ID: 592
This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long
-
Product ID: 908
This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. We think this would be most handy when putting a Beagle Bone, Raspberry Pi or Mintyboost into a box. The jack half has two mounting 'ears' with 12mm M3 screws installed, 30mm apart. The ears are flexible so the holes don't have to drilled very precisely....
-
Product ID: 62
This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things). 3 feet / 1 meter long Color may vary!
-
Product ID: 937
This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box. The jack half has two mounting 'ears' with M3 screws installed, ~1.1" / ~29mm apart. Can be used with box walls 0.125" to 0.25" wide. Depending on your usage you may...
-
Product ID: 18
This USB cable adds a DB9 serial port to your computer or laptop. Works with MacOS X, Linux and Windows. Note that this provides (approximately) +-6V serial (RS232) not 5V serial (TTL), good for old devices like GPS, handhelds, programmers, etc with chunky DB9's on the side. Some cheaper RS232 cables 'cheat' and only give you 0-5V which wont work with some devices -...
-
Product ID: 936
This handy USB extension cable will make it easy for you to enclose a device that has a mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, USB Boarduino, etc into a box! The jack half has two mounting 'ears' with M3 screws installed, ~28.5mm apart. Can be used with box walls 0.125" to 0.25" wide. If you have...
-
Product ID: 907
This handy USB extension cable will make it easy for you to enclose a device that has a B type port. We think this would be most handy when putting an Arduino in a box. The jack half has two mounting 'ears' with M3 screws installed, 1.1" / 29mm apart. Can be used with box walls 0.125" to 0.25" wide. If you have a thinner-walled box, simply swap out the M3 screws for...
-
Product ID: 1620
Add a power switch to any USB-powered project simply by plugging this between the USB power port and the USB cable. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a USB A socket on one end and a USB A plug on the other. In between is an in-line switch that is rated for 2 Amps. The data...
-
Product ID: 898
This here is your standard A-microB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your NETduino, Arduino Leonardo, Raspberry Pi (among other things). Approximately 6.5" long from end to end, its a little more compact than our classic 3' long cable We had these made to our specifications, available in Adafruit Black
-
Product ID: 1318
This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0, but with a twist! Literally! Instead of the cable coming straight out from the connector, there's a right angle bend. We thought this might make a good pair for a Raspberry Pi Model A or B as the cable doesn't stick out as far. We got cables with extra-beefy 24 AWG power wires, and 28 AWG data...
-
Product ID: 899
This here is your standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Teensy, USB Lipo charger (among other things). The cable is approximately 6" long - a little more compact than our classic 3' long cable We had these made to our specifications, available in Adafruit Black
-
Product ID: 1197
Mini or Micro? Mini or Micro??? Mini AND Micro! This is a handy USB cable, it's compact so you can toss it into your toolkit, and has both Mini-B and Micro-B connector. Now you can hook up your LiPo Charger or a Arduino Micro/Leonardo/Raspberry Pi using the same cable, sweet! Approximately 8" long from end to end, its a little more compact than our classic 3' long...
-
Product ID: 974
This flexible USB swivel adapter will extend your USB port out of the way. Useful when you want to attach a 'bulky' USB device without blocking a secondary port. We thought this would be handy for BeagleBone or Raspberry Pi users. Rotates 180 degrees in two axes, with a very nice solid construction.
-
Product ID: 1099
This cable looks like a USB micro cable but it isn't! Instead of a USB A Plug, it has a USB A Socket on the end. This cable is designed for use with OTG (On the Go) host devices (like the Arduino Due or many tablets) so you can connect a mouse, keyboard, or any other USB device. You'll still need to have drivers on the device, this cable is just a cable and contains...
-
Product ID: 988
This little dongle will let you connect one of our 5V 2Amp or 5V 10Amp adapters to something that expects to connect to USB. The premise is simple - one end has a USB A female jack and the other has a 'standard' 5.5mm OD/2.1mm ID barrel jack with center positive polarity. It does not have any resistors or other connections inside for the data lines so this won't work...
-
Product ID: 2379
ON...off...ON...off...ON...off...ON...off...WE CAN'T STOP CLICKING THIS ON-OFF SWITCH! It has such a satisfying click and it works so well. Plus, it's just about perfect for charging your Raspberry Pi - either Model B, A+, B+, or Pi 2. Just hook up the standard USB end to a 5V 1A USB port power supply or 5V 2A USB port power supply and the Micro B end to a Raspberry...
-
Product ID: 2185
This is your standard USB A-Plug to Micro-USB cable. It's 2 meters long so you'll have plenty of cord to work with for those longer extensions. Perfect for connecting to your Raspberry Pi, Arduino Leonardo/Micro, FONA or Trinket (among other things). It's got extra beefy 24 AWG power wires so it works great for high power (1-2 Amp) computer powering. If you want...
-
Product ID: 2727
The premise of this MicroUSB Plug to 5.5/2.1mm Jack adapter is simple. There's a MicroUSB plug on one end and a 5.5mm/2.1mm DC barrel jack with center positive polarity on the other. This allows you to connect one of our 5V 2 Amp, 5V 4A or 5V 10 Amp adapters to something that expects to connect to 5V USB. We also have a shorty adapter-without-cable version Since this...
-
Product ID: 2264
Wouldn't it be cool to drive a tiny OLED display, read a color sensor, or even just flash some LEDs directly from your computer? Sure you can program an Arduino or Trinket to talk to these devices and your computer, but why can't your computer just talk to those devices and sensors itself? Well, now your computer can talk to devices using the Adafruit FT232H breakout...
-
Product ID: 5978
Throw out all those Mini and Micro B USB cables you have in a plastic bin - the next generation of USB connectors is here with USB C! You've seen these connectors pop up on all sorts of devices, as the industry moves from micro B or lightning to the new standard. Well, at least until the next standard comes out USB C features a symmetric/reversible connector, more...
-
Product ID: 5030
If you've got a computer or laptop with a USB C port, but you're itching to use one of our fancy new Trinkeys, this adapter will do an excellent job at turning that USB Type C port into a USB A port! Works great with any device that has a USB C port. These adapters don't magically give you USB C speeds into a USB 2.x device, and they won't give you the power...
-
Product ID: 6069
If you need to add a compact panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB C Small Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project. The adapter can fit holes 12mm to 18mm, so you can drill in your wood, plastic, or metal with a common hole-saw or bit, no special...
-
Product ID: 4055
This panel mount cable will allow you to enclose a device that has a USB A port. Perfect for placing your project in a secure box. Both ends have standard USB A, an extension cord if you will. What's special about this, you ask? It's a Snap-In Panel Mount Cable - much easier than a classic panel mount cables, you don't need screws or drills for installation. Cut out...
-
Product ID: 4053
This panel mount cable will allow you to enclose a device that has a USB A port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Type A plug connector, and other is a USB C socket with special over-molding. The socket side has two mounting 'ears' with M3 screws installed 20mm apart....
-
Product ID: 4056
This panel mount cable will allow you to enclose a device that has a USB Micro B port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB Micro B plug connector, and other is a USB C socket with special over-molding. The socket side has two mounting 'ears' with M3 screws installed 20mm...
-
Product ID: 5450
This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 12V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotation...
-
Product ID: 4261
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this USB C Jack to USB C Jack Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes...
-
Product ID: 4449
If you'd like to connect a USB-host-capable chip to your USB peripheral, this cable will make the task very simple. There is no converter chip in this cable! It's basically a plain USB cable that's cut in half and with jumper sockets on the power and data lines. Simple to use, does the job when you have something that exposes the D+/D- pins. Red wire connects to 5V...
-
Product ID: 3318
Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, BeagleBone, or any other Mini-B device into a box! This Mini-B male/female extension cable features a male USB Mini-B plug on one end, and a bulkhead...
-
Product ID: 4474
As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around a USB Type A hub, computer or laptop. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among...
-
Product ID: 3561
If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 20 cm (~8 inches)...
-
Product ID: 4218
If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB C Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project. The adapter can fit holes 21.5mm to ~27mm, so you can drill in your wood, plastic, or metal with a common hole-saw or bit, no special shapes or filing...
-
Product ID: 5879
UPDI stands for Unified Program and Debug Interface, but this board is so smol and cute that we will call it the Unusually Playful Device Interfacer and pat its head when it does a good job. It's designed to make programming modern ATtiny chips very easy because it has 3V or 5V power and logic select, power and transmit indicator LEDs, and a quick cable for poking...
-
Product ID: 4105
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Right Angle USB Micro B Plug Down only. (We also have the matching 'up'...
-
Product ID: 4472
As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around a USB Type A hub, computer or laptop. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among...
-
Product ID: 6050
When you want a svelte USB C build, a 'sunken' type connector that straddles the PCBA will let you keep your build super slim. This breakout gives you all the contacts for a USB Type C connector, but lower than the classic 'horizontal' USB-C breakout and a vertical version. USB C features a symmetric/reversible connector, more data pins, and higher current output...
-
Product ID: 1826
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY MicroB Male connector. It's a little more elegant because instead of snapping two pieces together the connector press-fits into the overmolding for a modern look. We also carry the slim size in USB-A male and USB-microB female....
-
Product ID: 3560
If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 10 cm (~4 inches)...
-
Product ID: 4199
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has...
-
Product ID: 5335
Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your every-day serial data from a microcontroller to computer. What now? Enter the Adafruit CP2102N Friend! The CP2102N is very similar to the CP2104. Despite having a name with a lower number, its actually considered the...
-
Product ID: 4473
As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around a USB Type A hub, computer or laptop. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among...
-
Product ID: 3258
Check out this handy MicroUSB extension cable, which will make it easy for you to enclose a device that has a B type (micro USB host) port. Great if you need to extend the USB port for your Raspberry Pi, Arduino, Feather or really anything development board. This Micro-B male/female extension cable features a male USB Micro-B plug on one end, and a bulkhead mountable...
-
Product ID: 4217
If you need to add a panel-mount connection for USB Micro B, but don't have the time or ability to cut a custom oval or square hole, this Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your existing micro-B USB kit. The adapter is about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or...
-
Product ID: 4432
As technology changes and adapts, so does Adafruit, and speaking of adapting, this right angle adapter is USB C socket-to-plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB A correctly the first time? Works great with any...
-
Product ID: 4259
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required....
-
Product ID: 6071
This panel mount cable is great for making USB Host or (some) client connections with a panel-mount setup. On the small panel-mount side you get a USB C connector, the other end has power, ground and D+ / D- lines. We particularly like that the panel mount part is very small, only about half an inch diameter, and you get a JST PH cable on the other end for quick...
-
Product ID: 3563
If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 50 cm (~20 inches)...
-
Product ID: 6153
This panel mount cable is great for making USB Type C connections with a panel-mount setup. On the small panel-mount side you get a USB C connector, the other end has power, ground, D+ / D-, and CC1/CC2 lines. We particularly like that the panel mount part is very small, only about half an inch in diameter, and you get a JST PH cable on the other end for quick...
-
Product ID: 5994
No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter cable will be able to get this-connected-to-that. It supports RS232 serial, TTL UART serial, RS485 and RS422. All with quick-connecting screw terminals so you don't need to do any soldering or use special cables. Just plug directly into a computer's USB A or C...
-
Product ID: 4448
If you'd like to connect a USB-capable chip to your USB host, this cable will make the task very simple. There is no converter chip in this cable! Its basically a plain USB cable that's cut in half and with jumper sockets on the power and data lines. Simple to use, does the job when you have something that exposes the D+/D- pins. Red wire connects to 5V power (from...
-
Product ID: 3610
This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in another USB device. For example, a Pi Zero or Pi Zero W has a OTG port, as does the Arduino Zero, and anything with an ATSAMD21 that is in USB host mode. Also...
-
Product ID: 5461
As technology changes and adapts, so does Adafruit, and speaking of adapting, this wee microadapter has a USB A jack (e.g. it will plug into a computer with an A port) and a USB C socket so your older computer or laptop can catch up to the latest USB Type C. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe...
-
Product ID: 6070
If you need to add a panel-mount connection that extends a micro SD card, this Round Panel Mount MicroSD Adapter Plug is the easiest and fastest way to panel-ify your project. The adapter is about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut,...
-
Product ID: 6068
If you need to add a compact panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB Micro B Small Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project. The adapter can fit holes 12mm to 18mm, so you can drill in your wood, plastic, or metal with a common hole-saw or bit, no special...
-
Product ID: 4331
Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit. This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It...
-
Product ID: 6032
This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 12V DC output, at up to 3A (or whatever the power adapter can do) Please note: If your USB...
-
Product ID: 4993
Here's an easy solution for keeping your USB C devices free from dust and other unsavory particulates. These squishy Silicone USB C Dust Cover Inserts slip neatly into any computer or device with a USB C socket, from the Adafruit Feather STM32F405 Express to the Raspberry Pi 4. Comes in a pack of ten, so you're set even if you have a computer with a lot of ports, or...
-
Product ID: 6030
This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 5V DC output, at up to 3A (or whatever the power adapter can do) Please note: This adapter...
-
Product ID: 4109
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Straight USB Type A Male Plug only. Ribbon cable and other adapter not...
-
Product ID: 1387
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper connector with easy-to-solder tabs. USB DIY Connector Shell - Type A Male Plug (3:13)
-
Product ID: 5893
UPDI stands for Unified Program and Debug Interface, but this board is so smol and cute that we will call it the Unusually Playful Device Interfacer and pat its head when it does a good job. It's designed to make programming modern ATtiny chips very easy because it has 3V or 5V power and logic select, power, and transmit indicator LEDs, and a quick cable for poking...
-
Product ID: 3878
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to Micro B plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any computer that...
-
Product ID: 4216
If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this USB B Round Panel Mount Extension Cable is the easiest and fastest way to panel-ify your project. The adapter is about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or...
-
Product ID: 5452
This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 20V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...
-
Product ID: 4212
If you need to add a panel-mount connection for USB B, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required....
-
Product ID: 1388
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper connector with easy-to-solder tabs. USB DIY Connector Shell - Type A Socket (4:59)
-
Product ID: 4175
As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a USB A plug and a USB C socket so your older computer or laptop can catch up to the latest USB Type C. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us...
-
Product ID: 5995
No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter will be able to get this-connected-to-that. It supports RS232 serial, TTL UART serial, RS485 and RS422. All with quick-connecting screw terminals so you don't need to do any soldering or use special cables. Just plug directly into a computer's USB A port and use...
-
Product ID: 3562
If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 30 cm (~12 inches)...
-
Product ID: 284
Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your every-day serial data from a microcontroller to computer. What now? Enter the FTDI Friend! The FTDI Friend is a tweaked out FTDI FT232RL chip adapter. Sure, like the well-known FTDI cable, it can provide power to your project...
-
Product ID: 3879
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to Micro B plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any computer that...
-
Product ID: 6372
We used a cable like this in a recent build and decided it's perfect for when you want to make a compact USB-C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging, while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...
-
Product ID: 4299
As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a Micro B USB jack and a USB C plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Since it uses a new connector, you may have lots of cables and power supplies that...
-
Product ID: 2910
This super slim, super tiny, and super cute Micro-B to USB on-the-go adapter is so slim, tiny, and cute that we'd pinch its cheeks if it was big enough to have cheeks. At just ~15.5mm long, ~11.3mm wide, and ~2mm, this really is the tiniest little adapter we've probably ever seen. But don't let the size fool you - this is a perfect and easy way to turn a device or...
-
Product ID: 5449
This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 9V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...
-
Product ID: 6073
This panel mount cable is great for making USB Host connections with a panel-mount setup. On the rectangular panel-mount side you get a USB Type A connector, the other end has power, ground and D+ / D- lines. We particularly like that the panel mount part is very small and snaps in and you get a wire pigtail cable on the other end for quick integration. What's...
-
Product ID: 4232
While this may appear to be an electronic shuriken, it's actually a Multifunctional USB Digital Tester! This handy (pun intended?) tool can measure voltage, current, power, charge time, and other measurements for USB A, Micro B, and USB C! It features a colorful display that pops up when you plug in a power supply. Each click of the button gives you a different...
-
Product ID: 6033
This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 20V DC output, at up to 3A (or whatever the power adapter can do) Please Note: The adapter...
-
Product ID: 1389
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper connector with easy-to-solder tabs. USB DIY Connector Shell - Type Mini-B Plug (4:59)
-
Product ID: 5329
If your computer has a USB A port still, and you want a small, cable-less way to connect our modern USB C devices, this little dongle will do the job nicely. It's quite simple - you've got your USB A plug on one side, a C plug on the other. Since C is reversible, you can always plug in your board upright.
-
Product ID: 6370
We used a cable like this in a recent build and decided it's perfect for when you want to make a compact USB-C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging, while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...
-
Product ID: 6324
This cable is not only super-fashionable, with a woven pattern in classic Adafruit black, it's also made for USB C for our modernized breakout boards, Feathers, and more. First, let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible cables, then you might as well have the nicest fabric-bound cable. Perfect for...
-
Product ID: 3589
Here's another super handy add-on for your Raspberry Pi computer, perfect for 'head-less' setups! The PiUART adds a USB Type-C to serial connection so you can use any serial port software to connect to the Pi's console. It plugs in and is fast and easy to add whenever you need to connect to your Pi. Two LEDs connect to RX and TX on the serial converter chip so you...
-
Product ID: 6371
We used a cable like this in a recent build and decided it's perfect for when you want to make a compact USB-C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging, while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...
-
Product ID: 5520
Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for woven fabric cables. Like, peep this fully reversible pink/purple Blinka-inspired cable or this mithril-like 3-in-1 Sync and Charge cable. Our latest addition to the collection is this 1 meter long Black Magnetic USB A or USB C to USB C Cable with a Magnetic Type C tip!...
-
Product ID: 5521
We picked up this adapter to 'MagSafe'-ify our laptop and found it so handy we figured we'd stock it in the shop as well. This is a right-angle Type C adapter, capable of handling 120W of power, so its perfect for laptop charging scenarios, but also has data lines so you can use it for any other sort of devices. Plug your USB C power (or data!) cable into the one...
-
Product ID: 5568
Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your everyday serial data from a microcontroller to computer. What now? Enter the Adafruit CH9102F Friend, a version of our popular USB-Serial 'friend' breakouts that uses the affordable (and available) CH9102F - a 'near...
-
Product ID: 6031
This convenient adapter lets you plug a USB Type C 3.1 5V cable into something with a 5.5mm / 2.1mm DC barrel socket. Works great with any device or cable with 5.5mm / 2.1mm DC barrel socket. Since USB C is reversible you can flip it for a left angle or right angle. You'll get 9V DC output, at up to 3A (or whatever the power adapter can do) Please note: If your USB...
-
Product ID: 6004
This handy USB extension cable will make it easy to enclose a device with an A-type (USB host) port. We think this would be most handy when putting a Beagle Bone, Raspberry Pi, or Mintyboost into a box. The jack half has two mounting 'ears' with 8mm M3 screws installed, 30mm apart. The ears are flexible, so the holes don't have to be drilled very precisely. Can be...
-
Product ID: 6367
We used a cable like this in a recent build and decided its perfect for when you want to make a compact USB C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...
-
Product ID: 2778
This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 12V powered devices with a center-positive DC barrel jack from a USB port. We also have a version that provides 9V, and if you just need a passthough...
-
Product ID: 4364
Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit. This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It...
-
Product ID: 6077
If you'd like to connect a USB C connector to your favorite garment to make a fun wearable tech project, then try out the array of sewable connectors we have. This is a Type C connector that is oriented in a horizontal position to the sewable base it's housed on with red and black wires running through the bottom. The jack is molded into a rubber that can be hand or...
-
Product ID: 4106
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Straight USB Micro B Male Plug only. Ribbon cable and other adapter not...
-
Product ID: 4110
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Straight USB Type A Female Socket only. Ribbon cable and other adapter not...
-
Product ID: 6273
This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 28V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...
-
Product ID: 6265
This USB C PD to 2.1mm Cable with Selectable Voltage Button will help you get the most out of your USB C Power Delivery wall warts by letting you select any of the available voltages to power a device that expects a 5.5mm outer diameter / 2.1mm inner diameter DC plug. Now you can get rid of all those wall adapters you have stashed in the plastic bin in the basement!...
-
Product ID: 5216
If you have a USB Type C port on your computer over here and you want to connect something over there then this extension cable will do the job right quick! This cable is 2 meters long, with all the pins connecting from one side to the other.
-
Product ID: 4536
As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a 2.1mm barrel jack socket and a USB C plug - you could use this to power a USB C device from a common wall adapter. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Plug...
-
Product ID: 4052
This panel mount cable will allow you to enclose a device that has a USB A port, and also converts it to a modern USB C connector at the same time. Perfect for placing your project in a secure box! One end is a USB A plug connector, and other is a USB C socket with special over-molding. What's special about this, you ask? It's a Snap-In Panel Mount Cable - much...
-
Product ID: 6368
We used a cable like this in a recent build and decided it's perfect for when you want to make a compact USB-C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging, while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...
-
Product ID: 4669
Here's one of the easiest capture solutions for getting HDMI data into your computer or Raspberry Pi, really any system with a USB port.. Use this capture device to convert a video signal from a camera (or another device) into a digital format your computer can recognize. Its trivially easy to use: connect one end to an HDMI output up to 1080p. Connect the other end...
-
Product ID: 2777
This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc) and it will give you a higher DC voltage! It's a handy way to power 9V powered devices with a center-positive 2.1mm DC barrel jack from a USB port. We also have a version that provides 12V, and if you just need a passthough...
-
Product ID: 5524
This is a magnetic USB Type C plug! They pair with the Black Woven USB A or Type-C to Type-C Cable with Magnetic Tip . Plug your USB C power (or data!) cable into one end, then insert the little magnetic nub into your device's charging port. Now you basically have a quick-detach USB C connector with a magnetic alignment. Easy to plug in whenever, no worries if the...
-
Product ID: 5220
If you have a USB Type C port on your computer over here and you want to connect something over there then this extension cable will do the job right quick! This cable is 1 meter long, with all the pins connecting from one side to the other.
-
Product ID: 5457
This cable is kinda fascinating - it has an integrated boost converter, so you can plug it into any USB port (from a computer, battery pack, etc), and it will give you a higher DC voltage! It's a handy way to power a 9V or 12V device. Unlike our other 'USB booster' cables, this one comes with a fancy lil display and a switch so you can select between 9V or 12V output...
-
Product ID: 6268
This USB Type C Sync Data Cable with On/Off Switch cable is great when you don't want to plug-and-unplug a device to turn it on and off. It's a true USB C to C cable, with power, data and power delivery (USB C PD) lines connected so it can be used for high voltages/currents as well as data syncing. When switched ON it acts as a normal cable. When OFF the power line...
-
Product ID: 5501
This unusual cable is sort of the 'ultimate' in USB type C Power Delivery (PD) hacking: good for experienced hardware hackers who are comfortable with a cable that can shape-shift from one setting to the other. Instead of having to juggle multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power...
-
Product ID: 4104
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a USB Right Angle Micro B Plug Up only. (We also have the 'down' version...
-
Product ID: 4696
Perhaps your smart phone, tablet, or even your Raspberry Pi 4, charges off of USB, but can you really trust that charging station at the airport? Now you can control when to allow data in or out of your device with this specially-designed USB cable.Voila! Your cable's data lines can now be switched on or off. USB C is the latest industry-standard connector for...
-
Product ID: 5328
Turn any USB Type C device into a pluggable USB key with this 'plug to plug' adapter. Works with Windows / Linux computer/laptops with a USB type C port. This adapter doesn't work with Macbook laptops due to a mistake in the design: The CC1/CC2 pins should only be connected once but they are connected both times - that means that Power Delivery chips get confused and...
-
Product ID: 4108
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Straight USB Type C Male Plug only. Ribbon cable and other adapter not...
-
Product ID: 1827
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY USB-A Male connector. It's a little more elegant because instead of snapping two pieces together the connector press-fits into the overmolding for a modern look. We also carry the slim size in Micro-B Male and USB-microB female....
-
Product ID: 6369
We used a cable like this in a recent build and decided its perfect for when you want to make a compact USB C-to-C connection in an enclosure. The metal plugs are durable and easy to grip for plugging and unplugging while the ribbon cable is flexible and short. Also great for going through slots or fitting through closed drawers/windows/doors. We verified that this...
-
Product ID: 6116
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this USB C plug to USB Printer B socket Round Panel Mount Cable is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no...
-
Product ID: 1829
As an addition to our other USB DIY shells, we have a 'micro B female' in a panel-mount-like connector. This isn't true panel mount but you could glue the black plastic shell into your project and then press-fit in the micro B connector. The 5-pins are much easier to solder than a surface mount connector We have other DIY "USB shells" are available in USB A plug,...
-
Product ID: 6269
This USB Type C Sync Data Cable with On/Off Switch cable is great when you don't want to plug-and-unplug a device to turn it on and off. It's a true USB C to C cable, with power, data and power delivery (USB C PD) lines connected so it can be used for high voltages/currents as well as data syncing. When switched ON it acts as a normal cable. When OFF the power line...
-
Product ID: 4111
This cable is not only super-fashionable, with a woven pink and purple Blinka-like pattern, it's also fully reversible! That's right, you will save seconds a day by not having to flip the cable around. First let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible cables, then you might as well have the nicest...
-
Product ID: 6278
Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for colorful cables that make our projects look like Transformers. Like, peep this fully reversible pink/purple Blinka-inspired cable. Or the USB C to USB C Cable w/ 100W Watt Display - 1 meter Black Woven. Our latest addition to the collection is this mechatronic...
-
Product ID: 4214
If you need to add a panel-mount connection for Micro USB, but don't have the time or ability to cut a custom oval or square hole, this USB A Jack to Micro USB B Jack Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit,...
-
Product ID: 3438
Your cell phone charges off of USB, but can you really trust that charging station at the airport? Now you can control when to allow data in or out of your device with this little USB extension cable. You can plug it onto the end of any USB data/sync cable you have: mini-USB, micro-USB, Apple Lightning, or any other proprietary type. Voila! Your cable's data lines...
-
Product ID: 4260
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this USB C jack to USB Micro B jack Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special...
-
Product ID: 4907
If you're a DIY enthusiast who'd like to update your power only project's connection to the latest USB standard, here is a 10-pack of USB C power only jack connectors! They're sturdy metal with 4 through-hole mounting tabs. It's really hard to rip these off a PCB. In an SMT line, you can just paste over the through-hole slots, and the pads will solder in place. We...
-
Product ID: 5523
This is a magnetic USB micro b plug! They pair with the Black Woven USB A or Type-C to Type-C Cable with Magnetic Tip . Plug your microUSB power (or data!) cable into one end, then insert the little magnetic nub into your device's charging port. Now you basically have a quick-detach microUSB connector with a magnetic alignment. Easy to plug in whenever, no worries if...
-
Product ID: 6279
Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for colorful cables that make our projects look like Transformers. Like, peep this fully reversible pink/purple Blinka-inspired cable. Or the USB C to USB C Cable w/ 100W Watt Display - 1 meter Black Woven. Our latest addition to the collection is this mechatronic...
-
Product ID: 3030
Double up on your micro USB capabilities with the Micro B USB 2-Way Splitter Cable. This splitter is great for reducing cable clutter and freeing up port space. It takes a single Micro B connection (with data and power) and gives you two outputs. The longer cable has data and power brought to it. The shorter cable is only power. You can also use it just for power...
-
Product ID: 5789
Everyone has that "good charger" in the house, the one that seems to get your phone from 4% to 100% in record time. But it's a bit of a mystery, isn't it? Why does one charger work great while another doesn't seem to budge at all? It has to do with whether that charger supports USB Type C Power Delivery (PD) and, of course, the supply's output current ability and the...
-
Product ID: 6029
Everyone has that "good charger" in the house, which seems to get your phone from 4% to 100% in record time. But it's a bit of a mystery, isn't it? Why does one charger work great while another doesn't seem to budge at all? It has to do with whether that charger supports USB Type C Power Delivery (PD) and, of course, the supply's output current ability and the length...
-
Product ID: 5446
This USB Type C cable adds a DB-9 (DE-9) serial port to your computer or laptop. Works with MacOS X, Linux, and Windows. Note that this provides (approximately) +-6V serial (RS232) not 5V serial (TTL), good for old devices like GPS, handhelds, programmers, etc with chunky DB9's on the side. Some cheaper RS232 cables 'cheat' and only give you 0-5V which won't work...
-
Product ID: 4107
If you love DIY cable-rigging, then these USB adapters are right up your alley! Making custom USB cables has never been easier. Just grab one of our ribbon cables, then swap and switch any of our USB adapters on each end using the flex cable clips. There are options a-plenty! This version is a Straight USB Micro B Jack only. Ribbon cable and other adapter not...
-
Product ID: 5788
Everyone has that "good charger" in the house, the one that seems to get your phone from 4% to 100% in record time. But it's a bit of a mystery isn't it? Why does one charger work great while another doesn't seem to budge at all. It has to do with whether that charger supports USB Quick Charge, and of course the output current ability and the length and quality of...
-
Product ID: 4213
If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this Micro USB B Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required....
-
Product ID: 6075
If you'd like to connect a DC Jack to your favorite garment to make a fun wearable tech project, then try out the array of sewable connectors we have. This is a 5.5/2.1mm DC Jack that is oriented in a horizontal position to the sewable base it's house on with red and black wires running through the bottom. The jack is molded into a rubber that can be hand or...
-
Product ID: 6118
This one goes out to all the A/V professionals, broadcast engineers, and black box fans in the audience! This handy HDMI and USB Type-C Panel Mount Extension cable will make it easy to extend your project, which needs both power/data over USB and a video output or input signal over classic HDMI connectors. You get plenty of extra cable, too, 1 meter of each, for...
-
Product ID: 6076
If you'd like to connect a Micro-B connector to your favorite garment to make a fun wearable tech project, then try out the array of sewable connectors we have. This is a Micro-B connector that is oriented in a horizontal position to the sewable base it's housed on with red and black wires running through the bottom. The jack is molded into a rubber that can be hand...
-
Product ID: 4342
Ready Players 1 and 2? Double up on your MakeCode gaming with a Sync Cable! We got this Micro B USB to Micro B USB cable specially made to connect you and your frenemy for co-op fun or player-versus-player showdowns. Works with our PyBadges and PyGamer - we connected the JACDAC pin to the 'extra' ID pin of the Micro B cable so data can pass back and forth. It's one...
-
Product ID: 2789
The premise of this MicroUSB to 5.5/2.1mm DC Barrel Jack Adapter is simple. There's a MicroUSB plug on one end and a 5.5mm/2.1mm DC barrel jack with center positive polarity on the other. This allows you to connect one of our 5V 2 Amp, 5V 4A or 5V 10 Amp adapters to something that expects to connect to 5V USB. We also have a cable-version of this, but this one is...
-
Product ID: 4009
At first glance this appears to be an ordinary A to micro B USB cable. Plug it in to your device and power supply, and you get a colorful glitter of dozens of little LEDs embedded in the length of the cable. Can be used for data and charging. The LEDs are luminous but not too bright. Perfect for vampire makers, candy ravers, or maybe night owls who misplace their...
-
Product ID: 4844
This ordinary-looking USB cable actually has a surprise trick up its rubber sleeve. It's kinda like a 'miniature KVM' (minus the video part, and only one USB port). The mechanical switch connects to the D+ and D- pins on the two USB A host ports. So when you switch back and forth, the USB peripheral connects from one to the other. So, suppose you're working with...
-
Product ID: 4932
If you're a DIY enthusiast who'd like to update your project's connection to the latest USB standard, here is a 10-pack of USB C plug connectors! They can be pick-and-placed onto your design, and then plugged directly into a USB C port. For mechanical connection, there's four SMT tabs - use plenty of solder to keep these secure, they aren't as good as through-hole...
-
Product ID: 4008
At first glance this appears to be an ordinary A to micro B USB cable. Plug it in to your device and power supply, and you get a colorful glitter of dozens of little LEDs embedded in the length of the cable. Can be used for data and charging. The LEDs are luminous but not too bright. Perfect for vampire makers, candy ravers, or maybe night owls who misplace their...
-
Product ID: 5356
This USB micro B "JIG" Dummy Plug is a small, handy device for those interested in debugging their smartphones or other devices that use the ID pin #4 for a special signal. This plug has a 300K resistor from the ID pin to ground, which can be used to resuscitate Samsung S4, S5, S6 and possibly others by putting into an emergency repair mode. It's also useful for...
-
Product ID: 993
This handy USB extension cable will make it easy for you to extend your USB cable when it won't reach. The connectors are gold plated for years of reliability. We use these handy cables all over our factory and homes. Cable is standard "Adafruit black". Cable length: 10 feet (3 meters)
-
Product ID: 4198
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has...
-
Product ID: 5045
As technology changes and adapts, so does Adafruit, and speaking of adapting, check this Right Angle Black Woven USB-C to USB-A Cable. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Works great with any device or cable that has a USB C port. This cable is a...
-
Product ID: 5451
This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 15V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...
-
Product ID: 5044
This cable is not only super-fashionable, with a woven pink and purple Blinka-like pattern, it's also made for USB C for our modernized breakout boards, Feathers and more. If you want something just like it but for Micro B, we have a B version here. First, let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible...
-
Product ID: 6065
On our first Pentium 120 tower (purchased at PCs for Everyone on Thorndike st in Cambridge Mass) came with two DE-9 serial ports on the back: COM1 and COM2. Perfect for connecting a mouse and maybe a modem. Nowadays, long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your...
-
Product ID: 5031
Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for woven fabric cables. Like, peep this fully reversible pink/purple Blinka-inspired cable or this mithril-like 3-in-1 Sync and Charge cable. Our latest addition to the collection is this 1 meter long Adafruit Black Woven USB Cable with USB Type A to Right Angle USB Type C....
-
Product ID: 5153
This cable is not only super-fashionable, with a woven pink and purple Blinka-like pattern, it's also made for USB C for our modernized breakout boards, Feathers, and more. If you want something just like it but for Micro B, we have a B version here. First, let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible...
-
Product ID: 900
This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP, or USB Boarduino (among other things). 6" long from end to end, its a little more compact than our classic 3' long cable We had these made to our specifications, available in Adafruit Black
-
Product ID: 260
This here is your standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Teensy v2, USB Lipo charger w/Mini B connector, among other things. Approximately 3 feet / 1 meter long Color may vary!
-
Product ID: 971
This is a nice solution to wanting to use PS/2 devices (such as our capacitive touch pad or magstripe readers). It's also handy if you want to connect a keyboard and mouse to a Raspberry Pi or Beagle Bone without taking up two USB ports. Inside is a full translation chip - a small USB microcontroller that will translate the PS/2 into "USB Keyboard" and "USB Mouse" We...
-
Product ID: 1514
For charging nearly any kind of portable gadget, this 3-in-1 cable can handle it. Great for use with a Mintyboost, or our USB power packs (or just powering your projects). One USB-A jack splits into three connectors: Micro USB, iPhone/iPad/iPod 30pin (for older iDevices) and the newer Lightning (newer iDevices). Approximately 6" long from end to end, it's a little...
-
Product ID: 2008
Oooh it's so soft! And that beautiful pattern! If you have to have visible cables then you might as well have the nicest fabric bound cable with a eye-catching snake-like pattern. That's why we now carry this standard A to micro-B USB cable for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino Leonardo/Micro, Raspberry Pi, NETduino, (among other things)....
-
Product ID: 1513
Linguine? Rice sticks? Soba? Whatever your favorite noodle may be, you will be pleasantly reminded whenever using this noodle-shaped cable. This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0 - but in a slim profile and classic Adafruit Black. Perfect for connecting a PC to your Arduino Leonardo/Micro, Raspberry Pi, NETduino, (among other things)....
-
Product ID: 2676
Close your eyes... Now feel your Wireless troubles drift slowly away... Wouldn't it be great if you could replace your wireless project with wires? These USB Signal Extenders may be able to do that for you! The extenders can take power and data from USB (1.0 and 2.0, 3.0 not supported) and transmit them along an ethernet cable of up to 150ft and then back into USB....
-
Product ID: 1470
Whether you're flying high, driving far, or out on the town with your friends, you'll never be without a charged phone again. You leave the house with your keys, phone, wallet, and CHARGECARD, the jumper cable for your phone. Features: Standard USB Charge/Sync Anywhere. 2.5mm Thick Durable, Flexible Plastic. Flexible Link for 360º Plug Movement. Plug Snaps Hold...
-
Product ID: 1472
Whether you're flying high, driving far, or out on the town with your friends, you'll never be without a charged phone again. You leave the house with your keys, phone, wallet, and CHARGECARD, the jumper cable for your phone. Features: Standard USB Charge/Sync Anywhere. 2.5mm Thick Durable, Flexible Plastic. Flexible Link for 360º Plug Movement. Plug Snaps Hold...
-
Product ID: 1473
The Thinnest USB Cable for iPhone 4/4s! ChargeCard fits in your wallet, so it's with you when you need it, and out of the way when you don't. Features: Standard USB plug for power and data transfer. Credit card sized, and only 0.1" thck. Rubber tongue allows full range of motion. USB plug snaps securely in place. CHARGECARD Ultra-thin USB Cable for iPhone 4/4S (30...
-
Product ID: 4715
Here's one of the easiest capture solutions for bringing old school audio and video into your computer or Raspberry Pi, really any system with a USB port... Use this capture device to convert an analog NTSC or PAL video signal from an older device into a digital format your computer can recognize. It's trivially easy to use: connect and match up the audio and either...
-
Product ID: 1390
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper connector with easy-to-solder tabs. USB DIY Connector Shell - Type Micro-B Plug (3:13)
-
Product ID: 1825
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY Mini-B Male Plug connector. It's a little more elegant because instead of snapping two pieces together the connector press-fits into the overmolding for a modern look. We also carry the slim size in USB-A male, microB male, and...
-
Product ID: 1828
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside This is the 'slim' version of the DIY USB-A Female connector. It's a little more elegant because instead of snapping two pieces together the connector press-fits into the overmolding for a modern look. We also carry the slim size in USB-A male, miniB plug, microB...
-
Product ID: 3087
Put USB to work in your designs with USB Complete: The Developer's Guide! This book bridges the gap between the technical specifications and the real world of designing and programming devices that connect over the Universal Serial Bus. This is Ladyada's favorite protocol book, and is great at explaining USB at a low level. As the most versatile computer interface...
-
Product ID: 3419
This here is a handy A male to A female USB extension cable. This handy USB extension cable will make it easy for you to extend your USB cable when it won't reach, but with a twist - literally! Instead of the cable coming straight out from the connector, there's a right angle bend on the male end. We use these handy cables all over our factory and homes. Cable is...
-
Product ID: 4910
Discontinued - you can grab this HDMI Input to USB 2.0 Video Capture Adapter instead! Here's one of the easiest capture solutions for getting HDMI data into any system with a USB-C port. Use this capture device to convert a video signal from a camera (or another device) into a digital format your computer can recognize. It's trivially easy to use: connect one end to...
-
Product ID: 3388
This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting any development board, microcontroller, mobile phone, or other device to your computer or charger. "Standard?" you might say... nothing gets past the astute eye of an Adafruit customer! Why yes, that is an LCD display embedded in the cable! This is basically like a USB cable...
-
Product ID: 3439
Your cell phone charges off of USB, but can you really trust that charging station at the airport? Now you can control when to allow data in or out of your device with this little USB extension cable. It can be used with any device that has a micro USB port, which is like just about anything except for Apple devices. Voila! Your cable's data lines can now be switched...
-
Product ID: 4148
This cable is super-fashionable with a woven pink and purple Blinka-like pattern! First let's talk about the cover and over-molding. We got these in custom colors, and if you have to have visible cables, then you might as well have the nicest fabric-bound cable with a eye-catching python pattern. Perfect for connecting to your PyPortal, Circuit Playground Express,...
-
Product ID: 3564
If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or socket adapters on each end using the flex cable clips. There are options a-plenty! This is the 100 cm (~40 inches)...