Power / LiIon & LiPoly

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can undo without tearing the contacts from the housing. Plugs in nicely all with our...

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in the middle, try this switched extension cable. Finally, for PCB and breadboard...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 500mAh for a total of about 1.9 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries. The batteries come pre-attached with a 2-pin JST-PH...

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together! This is an A-A cable, that...

Oh so handy, this little lipo charger is so small and easy to use you can keep it on your desk or mount it easily into any project! Simply plug it via any USB C cable into a USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit....

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 1200mAh for a total of about 4.5 Wh. If you need a larger battery, we also have a 2500mAh+ model The batteries come pre-attached with a 2-pin JST-PH connector as shown and include...

PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, you'll be able to keep your power-hungry project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V...

By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery, we also have a 1200mAh model The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of ~100mAh for a total of about 0.4 Wh. If you need a larger battery, we have a full range of bigger cells The batteries come pre-attached with a high quality 2-pin JST-PH connector as...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 350mAh for a total of about 1.3 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries. The batteries come pre-attached with a 2-pin JST-PH...

Oh so adorable, this is the tiniest little lipo charger, so handy you can keep it any project box! Its also easy to use. Simply plug in the gold plated contacts into any USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit. When...

This charger is the only one you need to keep all your Lithium Polymer (LiPoly) or Lithium Ion (LiIon) rechargeable batteries topped up. No matter the power source at your disposal! The Adafruit Universal USB / DC / Solar Lithium Ion/Polymer Charger can use USB, DC or Solar power, with a wide 5-10V input voltage range! The charger chip is super smart, and will reduce...

Need a big battery for your project? This lithium-ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage, and over-current protection. Each cell can provide 1A of current for about 4 hours so all together the peak current you can...

We're always on the look out for better ways to make projects portable: being able to charge your battery in the most convenient manner will let projects run no matter what power is available. The Adafruit bq25185 USB / DC / Solar Charger Board uses the new bq25185 is a nifty charger chip which has a lot of flexibility for different kinds of batteries (LiPoly, LiIon...

Oh so handy, this little lipo charger is so small and easy to use you can keep it on your desk or mount it easily into any project! Simply plug it via any MicroUSB cable into a USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit....

We're always on the look out for better ways to make projects portable: being able to charge your battery in the most convenient manner will let projects run no matter what power is available. Then we added a power supply chip with it to let you run your project without a separate board. The result is the Adafruit bq25185 USB / DC / Solar Charger with 5V Boost Board!...

Lithium-ion (also known as 'liion' or 'li-ion') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 10,050mAh (a.k.a 10 Ah) for a total of about 37 Wh. If you don't need as much power, we also have several mAh variations of LiPoly & LiIons. This pack uses higher-density 18650 cells...

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers!...

A simple 2-pin connector that is compatible with the "JST PH 2-pin" connector - perfect for soldering to the bottom of our 3.3V Logic Trinket and 5V Logic Trinket! These mate perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector. Note: This...

This is a Lithium Ion and Lithium Polymer battery charger based on the MCP73833. It uses a USB mini-B for connection to any computer or 'USB wall adapter'. Charging is performed in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-voltage trickle charge to keep the battery topped-up. The fast-charge current is...

We're always on the look out for better ways to make projects portable: being able to charge your battery in the most convenient manner will let projects run no matter what power is available. Then we added a power supply chip with it to let you run your project without a separate board. The result is the Adafruit bq25185 USB / DC / Solar Charger with 3.3V Buck...

Need a massive battery for your project? This lithium-ion pack is made of 3 balanced 2200mAh cells for a total of 6600mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage, and over-current protection. Each cell can provide 0.5C of current (1.1 A per) so all together the peak current you can...

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector.

Oh so handy, this little lipo charger is so small and easy to use you can keep it on your desk or mount it easily into any project! Simply plug it via any MiniUSB cable into a USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit....

Here's a great accessibility tool for removing Lipoly batteries with a JST connector from your board. Maybe you've got bigger hands or a gorgeous nail set, or perhaps you're nervous you might She-Hulk out and rip your battery from the wires. This 3D-printed JST PH Puller slips over the JST connector and pops it off with ease. Deceptively easy to use. Simply line up...

Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This charger is a very unique design, perfect for outdoor projects, or DIY iPod chargers. We've spent over a year testing and tinkering with this charger to come up with a plug and play solution to charging batteries with the sun and we're really pleased...

This small, palm-sized battery power meter has a small display that shows off how much juice is left in your single Lithium Ion/Polymer rechargeable battery. The color display has four levels of power indication once battery capacity becomes 100%, 75%, 50%, and 25%. When power is below 25%, only the red battery frame lights up. The design is pretty basic, it's just...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2000mAh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 400mAh for a total of about 1.9 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries. The batteries come pre-attached with a genuine 2-pin 25mm...

Need a big battery for your project? This lithium-ion battery contains a 2200mAh and a protection circuit that provides over-voltage, under-voltage, and over-current protection. Yet, it is slim and easy to fit into many project cases. This cell can provide 2C of peak current (4400mA). Note that these batteries are not designed to sustain such high loads, we suggest...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 350mAh for a total of about 1.3 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries The batteries come pre-attached with a genuine 2-pin JST-PH...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 420mAh for a total of about 1.55 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries The batteries come pre-attached with a genuine 2-pin JST-PH...

PowerBoost 500C is the perfect power supply for your portable project! With a built-in battery charger circuit, you'll be able to keep your project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects. If you need a 1A...

Lithium-ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light, and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 150mAh for a total of about 0.6 Wh. If you need a larger battery, we have a full range of bigger cells The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown...

Is your QT Py all alone, lacking a friend to travel the wide world with? When you were a kid you may have learned about the "buddy" system, well this product is kinda like that! A board that will watch your QT Py's back and give it the power and support to wander out past your USB port. This little lipo charger is designed to fit onto the back of any QT Py board, and...

If you have an ItsyBitsy or Pro Trinket you probably know it's the perfect little size for a portable project. This LiPoly backpack makes it really easy to do! Instead of wiring 2 or 3 boards together to make a charging system, this little PCB sits on top of the PCB and allows a LiPoly/LiIon battery to plug in. When the Pro Trinket or ItsyBitsy USB port is powered,...

This SHIM from the Pimoroni Pirates provides a convenient way of powering your Raspberry Pi Pico from a LiPo/LiIon battery. You can recharge the battery easily by providing power to the Pico's USB port, then take your Pico or Pico W project on the go with the battery pack powering your circuitry. Solder this neat little square to the pins on the back of your Pico,...

Charge your single-cell lithium ion/polymer battery any which way you like with this board. Have a USB connection? No problem, just plug into the miniUSB connector. Only have a wall adapter? Any standard 2.1mm DC adapter which puts out 5 to 12VDC will work fine. If both are plugged in, the charger will automatically choose whichever has the highest voltage. Other...

You can swap a coin-cell powered design that uses one-use Lithium 2450 cells for this rechargeable cell. This battery is like a little Lithium Ion battery, but in coin cell shape. It doesn't have a huge capacity, only about 120mAh, compared to the 600mAh common to primary non-rechargeable cells. There are a few things to watch out for when using these batteries:...

Having a discrete, slick, and tidy power supply is always tricky when taking a project on the go...but get ready to roam the earth worry free with the tiny little Pimoroni LiPo Shim! It aims to give you the most compact power supply possible for all versions of Raspberry Pi. You can either solder the 0.8mm thick PCB directly to the bottom of your GPIO header for a...

Add a tiny yet convenient power switch to your Pi with Pimoroni's On-Off SHIM! Pimoroni's SHIMs (Shove Hardware in the Middle) are a new range of boards designed to be small, affordable, and handy. They're just 0.8mm thick (the bare board, not including mounted components) and designed to be soldered straight onto the GPIO pins of your Pi, if you wish, so that you...

Pimoroni's Button SHIM gives you five handy, physical buttons and an RGB status LED, and it's HAT and pHAT-compatible! Pimoroni's SHIM-format boards are designed to slip neatly onto your Pi's GPIO pins and still allow you to use HATs and pHATs at the same time. Or solder the included female header onto Button SHIM and use it as a standalone board. The buttons and...

This is a special-purpose charger just for the rechargeable LIR2450 Lithium Ion coin cells. Slide the coin cell in the right way, and plug into any USB port to recharge - so easy! Takes about 3 hours to charge up, when its done, the green DONE LED will light up to let you know. Rechargeable coin cell is not included, but we have 'em in the shop here Charging is...

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield goes onto your Arduino and provides a slim rechargeable power pack, with a built in battery charger as well as DC/DC booster. Compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due - basically any...