Raspberry Pi

A mainstay in the world of makers and electronics, The Raspberry Pi® is a single-board, low-cost, high-performance computer first developed in the UK by the Raspberry Pi Foundation. Not only has it helped bring the joy of electronics and computer programming to people around the world, but it has also become a staple of the maker community. The ever-present Pi in its latest iteration—Raspberry Pi 4 Model B—as the Pi Foundation continues to improve on an already excellent product. There’s also the five-dollar Pi Zero – a game-changing Raspberry Pi in a much smaller package – as well as its WiFi-laced cousin, the Pi Zero W.

Since the release of the first Raspberry Pi, manifold products have been created to accompany, modify, and enhance the Pi’s capabilities. From touchscreens and displays to HATs, Bonnets, cameras and plates, the possibilities are endless when it comes to project ideas. We’ve also created a number of Raspberry Pi packs for young engineers and experts alike.

Be sure to check out all of our Raspberry Pi related products, as well as our posts and tutorials.

Angled shot of Raspberry Pi 3 - Model B.

Raspberry Pi 3 - Model B - ARMv8 with 1G RAM

Product ID: 3055

Did you really think the Raspberry Pi would stop getting better? At this point, we sound like a broken record, extolling on the new Pi’s myriad improvements like we’re surprised that the folks at the Raspberry Pi Foundation are continuously making their flagship board better. Still, we’ll say it again - the Raspberry Pi team have outdone themselves....

$35.00

In stock

Wall wart power supply with 2 US prong power

5V 1A (1000mA) USB port power supply - UL Listed

Product ID: 501

Need a USB jack for charging or powering a project, but don't want to lug around a computer? This switching supply gives a clean regulated output at up to 1000mA! 110 or 240 input, so it works in any country. The plugs are "US 2-prong" style so you may need a plug adapter, but you can pick one up at any hardware store for a $1 or so. This adapter was specifically...

$5.95

In stock

Angled shot of Assembled Pi Cobbler Plus

Assembled Pi Cobbler Plus - Breakout Cable - for Pi B+/A+/Pi 2/Pi 3/Pi 4

Product ID: 2029

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably a good time to upgrade your set up and accessorize using all of the Model B+'s / Pi 2's / Pi 3 / Pi 4's 40 pins....

$6.95

15 in stock

5V 2.5A Switching Power Supply with 20AWG MicroUSB Cable

Product ID: 1995

Our all-in-one 5V 2.5 Amp + MicroUSB cable power adapter is the perfect choice for powering single-board computers like Raspberry Pi, BeagleBone, or anything else that's power-hungry! This adapter was specifically designed to provide 5.25V, not 5V, but we still call it a 5V USB adapter. We did this on purpose to solve a problem that occurs often with USB-powered...

$8.25

31 in stock

Top view of Pack of 2 Black Plated Brass M2.5 Standoffs for Pi HATs.

Brass M2.5 Standoffs for Pi HATs - Black Plated - Pack of 2

Product ID: 2336

"These go to eleven." 11 millimeters that is! Our Black Plated M/F Brass Standoffs are engineered specifically to keep your Pi HAT snug on your Pi while also keeping the two boards separated, in particular, the HDMI port. These standoffs can also be screwed into each other allowing stacking multiple HATs on to one Pi! They're the perfect companion for any Pi Hat...

$0.75

In stock

Angled shot of assembled black Pi Model B+ / Pi 2 / Pi 3 Case Base with a clear lid.

Adafruit Raspberry Pi B+ / Pi 2 / Pi 3 Case - Smoke Base - w/ Clear Top

Product ID: 2258

It took awhile to perfect - but that's okay since we can now safely say that the Adafruit case for Raspberry Pi Model B+ / Pi 2 / Pi 3 is The Single Greatest Raspberry Pi Model B+ Case Ever. This enclosure was designed by Mike Doell - just like our elegant, beautiful, and functional Pi Case for Raspberry Pi Model B. Made of ultra-durable, super-glossy polycarbonate,...

$7.95

In stock

Raspberry Pi Model B+ 512MB RAM

Product ID: 1914

OMG OMG OMG, did you hear? There's a Raspberry Pi called the Model B+ and check it out...more USB ports, more GPIO, better power supply, four mounting holes, less sticky-out SD card! Yep, that's right, the fantastic engineers at Raspberry Pi HQ have blessed us with a new design. They've taken all the feedback over the last 3 years and rolled out a nice updated Pi...

$29.95

58 in stock

Angled shot of a GPIO Ribbon Cable for Raspberry Pi Model.

GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2/Pi 3/Pi 4/5 - (40 pins)

Product ID: 1988

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins, and for those of us who like to hack electronics, they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power...

$2.95

In stock

USB cable - USB A to Micro-B - 3 foot long

Product ID: 592

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long

$2.95

In stock

Angled shot of a 4-channel I2C-safe Bi-directional Logic Level Converter.

4-channel I2C-safe Bi-directional Logic Level Converter - BSS138

Product ID: 757

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flashcards, and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V. Here we've got a 4-channel I2C-safe Bi-directional Logic Level Converter that has open-drain-with-10K-pullups outputs, great for logic...

$3.95

In stock

Angled shot of Assembled Pi T-Cobbler Plus next to GPIO ribbon cable

Assembled Pi T-Cobbler Plus - GPIO Breakout - Pi A+, B+, Pi 2/3/4, Zero

Product ID: 2028

This is the assembled version of the Pi T-Cobbler Plus. It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi with 2x20 connector) The Raspberry Pi has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our...

$7.95

In stock

Stacking Header for Pi A+/B+/Pi 2/Pi 3 - 2x20 Extra Tall Header

Product ID: 1979

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The female header part has extra spaces to make it 23mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. The stacky pin part is also extra-long, 10mm, so that when a standard 1.5mm thickness PCB is...

$2.95

In stock

Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

Product ID: 2327

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM...

$17.50

In stock

Angled shot of half-assembled black Pi Model B+ / Pi 2 / Pi 3 Case Base.

Pi Model B+ / Pi 2 / Pi 3 Case Base - Smoke Gray

Product ID: 2256

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your...

$5.00

In stock

Stacking Header for Raspberry Pi - 2x13 Extra Tall

Product ID: 1112

Stack multiple plates, breakouts etc onto your Raspberry Pi with this custom-made extra-tall and extra-long 2x13 female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. The stacky pin part is also extra-long, 9.7mm, so that when a standard 1.5mm thickness PCB is installed,...

$1.95

In stock

Flex Cable for Raspberry Pi Camera or Display - 24" / 610mm

Product ID: 1731

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 24" / 610mm long We have cables in 2", 4", 8", 12", and 18" long so you can have the perfect fit. Each...

$2.95

In stock

MCP3008 - 8-Channel 10-Bit ADC With SPI Interface

Product ID: 856

Need to add analog inputs? This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the Raspberry Pi computer because it's fun to have analog inputs but the Pi does not have an ADC. We have a tutorial and code...

$4.50

97 in stock

Pimoroni Raspberry Pi 7" Touchscreen Display Case - Noir

Product ID: 2033

Noir is the new black! With this Noir Raspberry Pi 7" Touchscreen Display Case you can protect your lovely Pi Foundation PiTFT - 7" Touchscreen Display for Raspberry Pi! Three unique layers provide support and protection to the back of the display, leaving your touchscreen entirely unimpeded and all Raspberry Pi ports totally accessible. This case is also constructed...

$14.95

38 in stock

GPIO Stacking Header for Pi A+/B+/Pi 2/Pi 3 - Extra-long 2x20 Pins

Product ID: 2223

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra long 10mm pins, compared with our plain version which is the same base height but has 3mm header pins instead. With...

$2.50

In stock

Top view of Brass M2.5 Standoffs for Pi HATs

Brass M2.5 Standoffs 16mm tall - Black Plated - Pack of 2

Product ID: 2337

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories with extra tall headers properly secured while also keeping the two boards separated. These standoffs can also be screwed into each other just like the 11mm versions (made for...

$1.25

In stock

Pi Foundation Display - 7" Touchscreen Display for Raspberry Pi

Product ID: 2718

The 7” Touchscreen Display for Raspberry Pi gives users the ability to create all-in-one, integrated projects such as tablets, infotainment systems and embedded projects! The 800x480 display connects via an adapter board which handles power and signal conversion. Only two connections to the Pi are required; power from the Pi’s GPIO port and a ribbon cable...

$79.95

71 in stock

Flex Cable for Raspberry Pi Camera or Display - 300mm / 12"

Product ID: 1648

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display, for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 300mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order...

$1.95

In stock

Angled shot of Adafruit DC & Stepper Motor HAT.

Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

Product ID: 2348

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Raspberry Pi and motors are not included. Works with any and all Raspberry Pi computers with 2x20 connection port. Since the Raspberry Pi does not have...

$22.50

In stock

Angled shot of Adafruit Perma-Proto HAT for Pi Mini Kit on a Raspberry Pi.

Adafruit Perma-Proto HAT for Pi Mini Kit - No EEPROM

Product ID: 2310

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED,...

$4.95

In stock

GPIO Header for RaspberryPi A+/B+/Pi 2/Pi 3 - Tall 2x20 Female Header

Product ID: 1992

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 10mm height instead. With 3mm you don't have to cut the...

$2.95

In stock

Angled shot of a GPIO Ribbon Cable for Raspberry Pi Model A and B.

GPIO Ribbon Cable for Raspberry Pi Model A and B - 26 pin

Product ID: 862

That new Raspberry Pi® Model A or B computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V...

$2.95

In stock

Flex Cable for Raspberry Pi Camera or Display - 200mm / 8"

Product ID: 1647

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 200mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order...

$1.95

In stock

Angled shot of clear Pi Model B+ / Pi 2 / Pi 3 Case Lid.

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Clear

Product ID: 2257

$3.00

In stock

Adafruit PiTFT Plus 320x240 2.8" TFT + Capacitive Touchscreen

Product ID: 2423

Is this not the cutest little display for the Raspberry Pi? It features a 2.8" display with 320x240 16-bit color pixels and a capacitive touch overlay. That's right, instead of a resistive touchscreen, which requires a fingernail or stylus, you can now use a fingerpad. The screen looks much nicer, with a black bezel and glass overlay. If you don't need a capacitive...

$44.95

In stock

Angled shot of Flex Cable for Raspberry Pi Camera or Display - 2 meter

Flex Cable for Raspberry Pi Camera or Display - 2 meters

Product ID: 2144

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 2 meters long. We have cables in a ton of sizes so you can have the perfect fit. Each order comes with...

$5.95

In stock

Angled shot of a USB WiFi (802.11b/g/n) Module.

USB WiFi (802.11b/g/n) Module: For Raspberry Pi and more

Product ID: 1012

Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi and Beagle Bone's USB port to add a low cost, but high-reliability wireless link. We tried half a dozen modules to find one that works well with the Pi and Bone without the need of recompiling any kernels: its supported by the Bone's Angstrom installation that comes with...

$13.95

In stock

Spy Camera for Raspberry Pi

Product ID: 1937

Is your house haunted? Or, rather, are you convinced that your house is haunted but have never been able to prove it since you've never had a camera that integrated with your raspberry pi but was still small enough that the ghosts wouldn't notice it? Luckily, the Spy Camera for Raspberry Pi is smaller than a thumbnail with a high enough resolution to see people, or...

$39.95

In stock

HDMI Flat Cable - 1 foot / 30cm long

Product ID: 2197

Connect two HDMI devices together and save space with this basic flat HDMI 1.4 cable. It has nice molded grips for easy installation, and is 1 foot long (~30 cm). This cable is absolutely perfect for an LCD Raspberry Pi project. The cable is so thin and flexible that you won't have any loose dangling HDMI cables getting in the way, and you can even fit your Pi behind...

$3.95

In stock

Angled shot of Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2/3/Pi 4

Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2/3/4/Pi 5 - Mini Kit

Product ID: 2324

It's 10 PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS, so you can add precision time and location to your Raspberry Pi Model Pi 3, Pi Zero, A+, B+, or Pi 2, 3, 4, & 5. Here's the low-down on the GPS module: -165 dBm sensitivity, 10 Hz updates, 99 search channels. GPS +...

$29.95

In stock

Official Raspberry Pi HDMI Cable - 1 meter

HDMI Cable - 1 meter - Official Raspberry Pi

Product ID: 608

Connect two HDMI devices together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1 meter long (about 3 feet). This is a HDMI 1.3 cable. We're now stocking a very fancy Official Raspberry Pi cable with overmolding and a Pi logo. Please note that these molded connectors are a little chunkier than classic HDMI cables

$4.95

In stock

Side shot GPIO Header for Raspberry Pi A+/B+/Pi 2/Pi 3/Pi 4/Zero

GPIO Header for Raspberry Pi A+/B+/Pi 2/Pi 3/Pi 4/Zero - 2x20 Female Header

Product ID: 2222

Connect your own PCB to a Raspberry Pi with this normal-height female header. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but has 10mm header pins instead. With 3mm you don't have to cut the really long pins,...

$1.50

In stock

Panel mount HDMI Cable - 40 cm

Product ID: 978

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two #4-40 screws are used to attach the female socket end, 26.9mm apart. Two hex-body standoff-screws are included as shown above and the hex nuts are embedded inside the molded end. Cable is 40cm long...

$5.95

In stock

Adafruit Capacitive Touch HAT for Raspberry Pi - Mini Kit - MPR121

Product ID: 2340

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like touch-reactive tablets and phones, as well as control panels for appliances, which is where...

$14.95

In stock

Miniature Wireless USB Keyboard with Touchpad

Product ID: 922

Add a miniature wireless controller to your computer project with this combination keyboard and touchpad. We found the smallest wireless USB keyboard available, a mere 6" x 2.4" x 0.5" (152mm x 59mm x 12.5mm)! It's small but usable to make a great accompaniment to a computer such as the Beagle Bone or Raspberry Pi. The keyboard itself is battery powered (there's a...

$49.95

78 in stock

Flex Cable for Raspberry Pi Camera or Display - 1 meter

Product ID: 2143

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 1 meter long. We have cables in a ton of sizes so you can have the perfect fit. Each order comes with...

$3.95

59 in stock

Adjustable Pi Camera Mount

Product ID: 1434

Pimoroni's adjustable Pi Camera mount is a great accessory for Pi shutterbugs. Little screws attach the Pi Camera solidly and the design allows for multiple positions. There's also a 1/4" hole that you can use to attach the camera to a standard camera tripod mount. This mount works with the Pi Camera version 1 (5 MegaPixel) and version 2 (8 MegaPixel) both plain...

$4.95

In stock

Raspberry Pi Model B+ / Pi 2 / Pi 3 Case Lid - Smoke Gray

Product ID: 2244

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your...

$3.00

In stock

USB Cable with Type A and Micro B ends and switch in center

USB Power Only Cable with Switch - A/MicroB

Product ID: 2379

ON...off...ON...off...ON...off...ON...off...WE CAN'T STOP CLICKING THIS ON-OFF SWITCH! It has such a satisfying click and it works so well. Plus, it's just about perfect for charging your Raspberry Pi - either Model B, A+, B+, or Pi 2. Just hook up the standard USB end to a 5V 1A USB port power supply or 5V 2A USB port power supply and the Micro B end to a Raspberry...

$5.95

In stock

Flex Cable for Raspberry Pi Camera or Display - 18" / 457mm

Product ID: 1730

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 18" / 457mm long We have cables in 2", 4", 8", 12", and 24" long so you can have the perfect fit. Each...

$2.50

82 in stock

Board Edge Mounting Kit - Pack of 4

Product ID: 1116

Having difficulty attaching a PCB? This kit is especially useful when there are no mounting holes - as with the original Raspberry Pi. Instead of gluing, taping, epoxying, etc. use these elegant standoffs. They have these round hook things that are designed to grip standard 0.062" thickness PCBs either by the edge or by the corner. Comes in a pack of 4 with matching...

$2.95

In stock

Top view of Adafruit RGB Matrix HAT + RTC assembled onto a Pi and matrix LED panel. The LED panel displays an off-set square rainbow gradient.

Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit

Product ID: 2345

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2/3/Pi 4 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. Currently the Matrix driving software library does not support the...

$24.95

In stock

SD/MicroSD Memory Card - 16GB Class 10 - Adapter Included

Product ID: 2693

Add speedy mega-storage in a jiffy using this 16 GB Class 10 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters! Preformatted to FAT so it works out of the box with our projects. Works great with any device in the Adafruit shop that uses micro-SD cards. Ideal for use with Raspberry Pi, BeagleBone Black and other...

$19.95

In stock

Wireless Keyboard and Mouse Combo - One USB Port!

Product ID: 1738

Add a good quality, slim chiclet keyboard as well as an optical mouse to your Raspberry Pi, Beagle Bone Black or other mini-computer with this wireless combo set. Best of all, it only uses a single USB port! This combo comes with a sleek black chiclet keyboard and mouse both controlled by a single wireless USB dongle. The keyboard is a full QWERTY keyboard and is...

$19.95

In stock

3.5mm (1/8") DIY 4-Pole (TRRS) Plug

Product ID: 1799

Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 3.5mm TRRS Plug with four poles....

$2.95

In stock

40Pin IDC Breakout Helper Soldered into perma-proto

IDC Breakout Helper - 2x20 (40 pin)

Product ID: 2270

The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2 (40 pins). It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket....

$2.25

57 in stock

Top down view of a Adafruit PiTFT 2.2" HAT Mini Kit with desktop image on the display.

Adafruit PiTFT 2.2" HAT Mini Kit - 320x240 2.2" TFT - No Touch

Product ID: 2315

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high-speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all, it plugs right in on top of your Model A+ or B+ and...

$24.95

In stock

Angled shot of blue assembled Pi Model B+ / Pi 2 / Pi 3 case with the lid removed to show a Pi computer.

Pi Model B+ / Pi 2 / Pi 3 Case Base - Blue

Product ID: 2252

Now that we have The Single Greatest Raspberry Pi Model B+ / Pi 2 / 3 Case Ever - we decided to make it even better by adding COLORS!!!!! Mix and match snap-on lids and bases to form your favorite combinations. Buy one base then match different colored lids to your room or outfit. Or buy all of them so that you can adjust your Pi B+'s case based on your mood, your...

$5.00

In stock

Pimoroni Picade Console Controller Kit for Raspberry Pi 4 - PIM488

Product ID: 2707

Power-up your TV with a Pimoroni Picade Console Controller! It's a compact, Raspberry Pi-powered retro games machine with authentic arcade controls that plugs right into your TV, monitor, or other HDMI display. It's a stylish, retro, and fun arcade controller for your Raspberry Pi! Picade Console is fight stick-style arcade console that riffs off the Pimoroni Picade...

$99.95

10 in stock

Pi-EzConnect Terminal Block Breakout HAT

Product ID: 2711

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry Pi. Mini proto area for adding components. Add standard male or female headers for breadboard like...

$19.95

15 in stock

Cover of Programming the Raspberry PI: Getting Started with Python

Programming the Raspberry Pi: Getting Started with Python - Third Edition - 2021

Product ID: 1089

Program your own Raspberry Pi projects! An updated guide to programming your own Raspberry Pi projects. Learn to create inventive programs and fun games on your powerful Raspberry Pi--with no programming experience required. This practical book has been revised to fully cover the new Raspberry Pi 4, including upgrades to the Raspbian operating system. Discover how to...

$17.00

56 in stock

Stereo 3.5mm Plug/Plug Audio Cable - 6 feet

Product ID: 876

This basic cable comes with two 3.5mm (1/8" headphone jack size) stereo connectors. It's fairly straight forward, you'll commonly need these to connect two audio devices together. Cable is 6 ft long.

$2.95

In stock

USB cable with Type A and Right Angle Micro B end

Right Angle USB cable - A/MicroB

Product ID: 1318

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0, but with a twist! Literally! Instead of the cable coming straight out from the connector, there's a right angle bend. We thought this might make a good pair for a Raspberry Pi Model A or B as the cable doesn't stick out as far. We got cables with extra-beefy 24 AWG power wires, and 28 AWG data...

$4.95

65 in stock

Angled shot of assembled orange Pi Model B+ / Pi 2 / Pi 3 Case Base without lid.

Pi Model B+ / Pi 2 / Pi 3 Case Base - Orange

Product ID: 2250

$5.00

81 in stock

Adafruit Perma-Proto HAT for Pi Mini Kit - With EEPROM

Product ID: 2314

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected...

$7.50

In stock

Flex Cable for Raspberry Pi Camera or Display - 50mm / 2"

Product ID: 1645

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 50mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order...

$1.95

In stock

Angled shot of short black microcontroller.

Adafruit KB2040 - RP2040 Kee Boar Driver

Product ID: 5302

A wild Kee Boar appears! It’s a shiny KB2040! An Arduino Pro Micro-shaped board for Keebs with RP2040. (#keeblife 4 evah) A lot of folks like using Adafruit parts for their Keeb builds – but with the ItsyBitsy not being pin-compatible with the Pro Micro pinout, it really wasn't very easy without some sort of adapter plate. Now we’re seeing lots of...

$8.95

In stock

Aluminum Heat Sink for Raspberry Pi 3 - 14 x 14 x 8mm

Product ID: 3083

Looking for a nice way to cool down your Raspberry Pi 3? Check out this 14x14x8 Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface...

$1.50

In stock

USB OTG Host Cable with Micro B OTG male to A female in black

USB OTG Host Cable - MicroB OTG male to A female

Product ID: 1099

This cable looks like a USB micro cable but it isn't! Instead of a USB A Plug, it has a USB A Socket on the end. This cable is designed for use with OTG (On the Go) host devices (like the Arduino Due or many tablets) so you can connect a mouse, keyboard, or any other USB device. You'll still need to have drivers on the device, this cable is just a cable and contains...

$2.50

In stock

Angled shot of thin, green rectangular microcontroller with castellated pads.

Raspberry Pi Pico 2 - RP2350

Product ID: 6006

Raspberry Pi Pico 2 is Raspberry Pi Foundation's update to their popular RP2040-based Pico board, now built on RP2350: their new high-performance, secure microcontroller. With a higher core clock speed, double the on-chip SRAM (512KB), double the on-board flash memory (4MB!), more powerful Arm M33 cores, new security and low-power features, and upgraded interfacing...

$5.00

10 in stock

Angled shot of green Raspberry Pi microcontroller.

Raspberry Pi 5 - 8 GB RAM

Product ID: 5813

The Raspberry Pi 5 is the newest Raspberry Pi computer, and the Pi Foundation knows you can always make a good thing better! And what could make the Pi 5 better than the 4? How about a faster processor, USB 3.0 ports, and an updated Gigabit Ethernet chip with PoE capability? Good guess - that's exactly what they did! The Raspberry Pi 5 is the latest product in the...

$80.00

In stock

2x20 Socket Riser Header for Raspberry Pi HATs and Bonnets

Product ID: 4079

Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins. You can plug this into your Raspberry Pi GPIO port and then plug a HAT or Bonnet or Phat on top. Especially useful for Bonnets that have slim headers on the bottom, but you want them to clear some of the components on the Pi, or fit into a case nicer. The header body is...

$1.95

In stock

Raspberry Pi Zero 2 W

Product ID: 5291

Raspberry Pi Zero 2 W is the latest product in Raspberry Pi's most affordable range of single-board computers. The successor to the breakthrough Raspberry Pi Zero W, Raspberry Pi Zero 2 W is a form factor–compatible drop-in replacement for the original board. The board incorporates a quad-core 64-bit Arm Cortex-A53 CPU, clocked at 1GHz. At its heart is a...

$15.00

In stock

Angled shot of green, rectangular microcontroller with pre-soldered header.

Raspberry Pi Zero 2W with Header

Product ID: 6008

Raspberry Pi Zero 2 W is one of Raspberry Pi's most affordable range of single-board computers. The successor to the breakthrough Raspberry Pi Zero W, Raspberry Pi Zero 2 W is a form factor–compatible drop-in replacement for the original board. If you didn't think that the Raspberry Pi Zero 2 W could possibly get any better, then boy, do we have a pleasant...

$18.00

In stock

Aluminum Heat Sink for Raspberry Pi 3 or 4 - 15 x 15 x 15mm

Product ID: 3082

Looking for the best heat sink for your Raspberry Pi? Check out this nice and tall 15x15x15mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 or 4 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy....

$1.95

In stock

Angled shot of a cooling fan installed on a green microcontroller.

Official Raspberry Pi 5 Active Cooler

Product ID: 5815

The Raspberry Pi 5 Active Cooler is compatible with the Raspberry Pi 5 and the Raspberry Pi 5 Case. Designed for anyone who wants to push the performance of their Pi, as well as overclockers and other power users, it keeps your Raspberry Pi 5 at a comfortable operating temperature even when under heavy load thanks to both a mini heatsink that goes on top of your CPU...

$5.00

In stock

Angled shot of black, square-shaped power supply block with a coiled black cable.

Official Raspberry Pi 27W PD Power Supply 5.1V 5A with USB C

Product ID: 5814

The official Raspberry Pi PD USB-C power supply is here! Superfast with just the right amount of cable length to get your Pi 5 projects up and running! With true Power Delivery support, this supply can easily supply 5 A of current! Comes in gothy Adafruit Black! Features: AC 100-240V 50/60Hz input with US plugs. DC 5.1V 5A output. 27W maximum output power. 1.5m 18...

$12.00

In stock

Angle Shot of the Raspberry Pi AI Camera.

Raspberry Pi AI Camera with Sony IMX500

Product ID: 6009

The Raspberry Pi AI Camera is a compact camera module from Raspberry Pi based on the Sony IMX500 Intelligent Vision Sensor. IMX500 combines a 12-megapixel CMOS image sensor with on-board inferencing acceleration for various common neural network models, enabling users to develop sophisticated vision-based AI applications without needing a separate accelerator. The AI...

$70.00

29 in stock

Angled shot of two 20-pin short male headers.

Short Plug Headers for Raspberry Pi Pico - 2 x 20 Male Headers

Product ID: 5584

These two Short Plug / Male Headers alone are, well, lonely. But pair them with the Raspberry Pi Pico, and you're in business! These 2.54mm / 0.1" pitch headers are particularly cute and tiny and are designed to match perfectly with the Pico and our short socket headers. Note that you could use normal header with those sockets headers, but these are short and don't...

$0.95

In stock

Angled shot of green rectangular microcontroller with a Wi-Fi module and pre-soldered headers.

Raspberry Pi Pico WH - Pico Wireless with Headers Soldered

Product ID: 5544

The Raspberry Pi foundation changed single-board computing when they released the Raspberry Pi computer, now they're ready to do the same for microcontrollers with the release of the brand new Raspberry Pi Pico WH. This low-cost microcontroller board features their powerful new chip, the RP2040, and all the fixin's to get started with IoT embedded electronics...

$7.00

In stock

Angled shot of black rectangular microcontroller "Feather RP2040"

Adafruit Feather RP2040

Product ID: 4884

A new chip means a new Feather, and the Raspberry Pi RP2040 is no exception. When we saw this chip we thought "this chip is going to be awesome when we give it the Feather Treatment" and so we did! This Feather features the RP2040, and all niceties you know and love about Feather Measures 2.0" x 0.9" x 0.28" (50.8mm x 22.8mm x 7mm) without headers soldered in. Light...

$11.95

In stock

Raspberry Pi Pico RP2040

Product ID: 4864

The Raspberry Pi foundation changed single-board computing when they released the Raspberry Pi computer, now they're ready to do the same for microcontrollers with the release of the brand new Raspberry Pi Pico. This low-cost microcontroller board features a powerful new chip, the RP2040, and all the fixin's to get started with embedded electronics projects at a...

$4.00

In stock

Raspberry Pi 4 Model B - 2 GB RAM

Product ID: 4292

The Raspberry Pi 4 Model B is the newest Raspberry Pi computer made, and the Pi Foundation knows you can always make a good thing better! And what could make the Pi 4 better than the 3? How about a faster processor, USB 3.0 ports, and updated Gigabit Ethernet chip with PoE capability? Good guess - that's exactly what they did! The Raspberry Pi 4 is the latest product...

$45.00

In stock

Mini Aluminum Heat Sink for Raspberry Pi - 13 x 13 x 3mm

Product ID: 3084

Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy....

$0.95

In stock

Angled shot of two 20-pin socket headers.

Socket Headers for Raspberry Pi Pico - 2 x 20 pin Female Headers

Product ID: 5583

These Socket Headers alone are, well, lonely. But pair them with the Raspberry Pi Pico, and you're in business! Socket headers are like the duct tape of electronics. They're great for connecting things, soldering to perf-boards, sockets for wires or break-away header, etc. These particular ones are designed to match up with boards that have two rows of 20 pins, so...

$0.95

In stock

Adafruit PiRTC - Precise DS3231 Real Time Clock for Raspberry Pi

Product ID: 4282

This is the best battery-backed real time clock (RTC) you can get that allows your Raspberry Pi project to keep track of time if the power is lost. Perfect for data-logging, clock-building, NTP servers, time-stamping, timers and alarms, etc. Equipped with a genuine DS3231 RTC, it works great with the Raspberry Pi and has native kernel support. The datasheet for the...

$14.95

In stock

Adafruit QT Py RP2040

Product ID: 4900

What a cutie pie! Or is it... a QT Py? This diminutive dev board comes with one of our new favorite chip, the RP2040. It's been made famous in the new Raspberry Pi Pico and our Feather RP2040 and ItsyBitsy RP2040, but what if we wanted something really smol? A new chip means a new QT Py, and the Raspberry Pi RP2040 is no exception. When we saw this chip we thought...

$9.95

37 in stock

Angled shot of Official Raspberry Pi Power Supply 5.1V 3A with USB C with Power plug facing down.

Official Raspberry Pi Power Supply 5.1V 3A with USB C - 1.5 meter long

Product ID: 4298

The official Raspberry Pi USB-C power supply is here! And of course, we have 'em in classic Adafruit black! Superfast with just the right amount of cable length to get your Pi 4 projects up and running! Features: AC 100-240V 50/60Hz input with US plugs. DC 5.1V 3A output. 15.3W maximum output power. 1.5m 18 AWG cable. USB-C output connector

$7.95

In stock

Angled shot of a skinny green microcontroller with headers.

Raspberry Pi Pico H - Pico with Headers Soldered

Product ID: 5525

The Raspberry Pi foundation changed single-board computing when they released the Raspberry Pi computer, now they're ready to do the same for microcontrollers with the release of the brand new Raspberry Pi Pico H with Soldered Headers. This low-cost microcontroller board features their powerful new chip, the RP2040, and all the fixin's to get started with IoT...

$5.00

In stock

Angled Shot of the Raspberry Pi 512GB SSD.

Raspberry Pi NVMe SSD - 512GB

Product ID: 6089

Unlock ultimate performance for I/O intensive applications on Raspberry Pi 5 with a Raspberry Pi NVMe SSD. These SSD drives are specified by the Pi Foundation to have the best performance-for-price, and will work perfectly with any M.2 HAT or adapter (we stock many varieties). Features: 512GB capacity. High-performance Raspberry Pi NVMe SSD capable of:50k IOPS* (4kb...

$45.00

39 in stock

Adafruit CharliePlex LED Matrix Bonnet - 8x16 Blue LEDs

Product ID: 3467

You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet. This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a...

$12.95

60 in stock

Angled shot of disassembled black and gray, rectangular microcontroller case.

Official Raspberry Pi Foundation Raspberry Pi 5 Case + Fan

Product ID: 5816

Keep your Raspberry Pi® 5 computer safe and snug in this solid ABS acrylic enclosure. You can even pick up the official active cooler to super-charge your Pi 5 projects and stay frosty even under computational intensity. This case keeps your Pi secure, has labeled holes for connector access, and even comes with four little bumper feet. You can use all of the...

$10.00

In stock

Angled shot of two 20-pin stacking headers.

Stacking Headers for Raspberry Pi Pico - 2 x 20 Pin

Product ID: 5582

These two Stacking Headers alone are, well, lonely. But pair them with the Raspberry Pi Pico, and you're in business! What do they do? They stack. Put the headers through your Pico and then you can not only plug them into a solderless breadboard or perma-proto, but you could attach circuitry on top as well. If you want the Pico up top for access to the boot button,...

$1.50

In stock

Angled shot of green Raspberry Pi 5 microcontroller.

Raspberry Pi 5 - 4 GB RAM

Product ID: 5812

$60.00

In stock

Angled shot of green, credit-card-sized microcontroller in black rubber bumper case.

Protective Silicone Bumper for Raspberry Pi 5

Product ID: 6056

Protect and secure your Raspberry Pi 5 with Raspberry Pi Bumper, a snap-on silicone cover that protects the bottom and edges of the board. Features One-piece flexible silicone rubber bumper. Enables easy access to the power button. Mounting holes remain accessible underneath the bumper.

$3.00

In stock

Raspberry Pi NVMe SSD - 256GB

Product ID: 6090

Unlock ultimate performance for I/O intensive applications on Raspberry Pi 5 with a Raspberry Pi NVMe SSD. These SSD drives are specified by the Pi Foundation to have the best performance-for-price, and will work perfectly with any M.2 HAT or adapter (we stock many varieties). Features: 256GB capacity. High-performance Raspberry Pi NVMe SSD capable of:50k IOPS* (4kb...

$30.00

94 in stock

Adafruit RP2040 CAN Bus Feather - MCP2515 CAN Controller.

Adafruit RP2040 CAN Bus Feather with MCP2515 CAN Controller - STEMMA QT

Product ID: 5724

If you'd like quickly get started with CAN bus interfacing, with no soldering required, our Adafruit RP2040 CAN Bus Feather comes ready-to-rock with a microcontroller, CAN chipset, and terminal blocks for instant gratification. The controller used is the MCP25625 (aka an MCP2515 with built-in transceiver), an extremely popular and well-supported chipset that has...

$19.95

In stock

Still image of a Adafruit RGB Matrix Bonnet powering a Matrix.

Adafruit RGB Matrix Bonnet for Raspberry Pi

Product ID: 3211

You can now create a dazzling display with your Raspberry Pi with the Adafruit RGB Matrix Bonnet. These boards plug into your Pi and make it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. "Bonnet" boards work on Raspberry Pi with a 40-pin GPIO header — Zero, Zero W/WH,...

$14.95

In stock

Micro SD Card Extender - 68cm (26 inch) long flex cable

Product ID: 3688

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with a Micro SD Card Extender . This simple, but effective device gives you a long flexible cable, a psuedo Micro SD card on one end, and a matching micro SD card socket on the other. Plug in the card half and attach the socket wherever you like. This is a great hack for...

$6.95

In stock

Angled shot of blue, square-shaped CSI cable adapter board.

Adafruit CSI or DSI Cable Extender Thingy for Raspberry Pi

Product ID: 3671

Every time someone posts on the Adafruit forums and says they need to have a really long cable for their Pi Camera (CSI) or Pi Display (DSI), we say, "Oh you mean like some sort of CSI/DSI cable extender thingy? Yeah we don't have one of those in stock yet" But that time is over! Now we can say, "Yes we have a CSI/DSI Cable Extender Thingy in stock!" And we point...

$2.95

In stock

Angled shot of camera module assembled onto a Raspberry Pi 4 computer.

Raspberry Pi Camera Module 3 Standard - 12MP Autofocus

Product ID: 5657

Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi. Featuring autofocus and a 12-megapixel sensor, and supported by Raspberry Pi's Picamera2 Python library, Camera Module 3 gives you excellent image quality with precise control. Camera Module 3 Standard features a 75-degree diagonal angle of view. No additional lens is required to use this camera; it...

$25.00

In stock

Overhead shot of small RTC battery with a JST connector with an adhesive sticker.

Raspberry Pi 5 RTC Battery

Product ID: 5817

This is a Panasonic lithium manganese rechargeable coin cell with a pre-fitted two-pin JST plug. Designed for use as a long term battery backup for Raspberry Pi 5 computers.

$5.00

In stock

Angled shot of 12" long GPIO 2x10 IDC ribbon cable.

GPIO Ribbon Cable 2x10 IDC Cable - 20 pins 12" long

Product ID: 5294

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Has a nice soft flexible 20-line 0.05" ribbon cable and keyed IDC connectors. Good for JTAG connections, in particular - but is useful for anything really. This cable is 12" long and has 20 pins (2x10) in 0.1" x 0.1" spacing and two sockets crimped on...

$1.95

In stock

Demo Shot of the Raspberry Pi Monitor (Red/White) with the Raspberry Pi 400 Desktop - Full Computer Kit.

Raspberry Pi Monitor - Red and White Colorway

Product ID: 6088

The Raspberry Pi Monitor is a 15.6" full HD computer display. It's the perfect compact, versatile, user-friendly desktop display companion for Raspberry Pi computers and other devices. Coming in the signature Red and White Colors this ties in perfectly to the Raspberry Pi 400 Desktop - Full Computer Kit or Raspberry Pi 500 Desktop - Computer Only. The Raspberry Pi...

$100.00

40 in stock

Hammer Header Male - Solderless Raspberry Pi Connector

Product ID: 3662

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero, Bonnet, HAT or pHAT. Make sure to carefully read...

$2.25

In stock

Miniature 5V Cooling Fan for Raspberry Pi (and Other Computers)

Product ID: 3368

Looking for another way to keep your Raspberry Pi cool? Hook up this 5V Mini Cooling Fan and prevent your hard-working Pi from overheating! Of course, it's also great for use with any small computer or FPGA or motor driver or anything that needs cooling. Plug the fan directly into your Raspberry Pi's 5V+GND GPIO power pins, as shown, for instant cooling! Place in...

$3.50

In stock

Raspberry Pi Camera Module 3 - 12MP 120 Degree Wide Angle Lens

Product ID: 5658

Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi. It offers an IMX708 12-megapixel sensor with HDR, and features phase detection autofocus. Camera Module 3 is available in standard and wide-angle variants, both of which are available with or without an infrared cut filter. Need a wider field of view than the standard 75 degrees? Camera Module 3 Wide...

$35.00

In stock

Raspberry Pi 3 - Model B+ - 1.4GHz Cortex-A53 with 1GB RAM

Product ID: 3775

The Raspberry Pi 3 Model B is the most popular Raspberry Pi computer made, and the Pi Foundation knows you can always make a good thing better! And what could make the Pi 3 better? How about a faster processor, 5 GHz WiFi, and updated Ethernet chip with PoE capability? Good guess - that's exactly what they did! The Raspberry Pi 3 Model B+ is the latest product in the...

$35.00

In stock

USB Mini Hub with Power Switch

Product ID: 2998

Do you want your cup to runneth over with USB ports? Do you want it to also be filled with the sweet, sweet nectar of an on-off switch? If the answer to either of those questions is yes - or "I never really thought about it that way but I guess so" - then this is the perfect product for you! This USB hub has four USB 2.0 ports each with a max total transmission speed...

$4.95

In stock

Angled shot of a Zero4U - 4 Port USB Hub for Raspberry Pi Zero.

Zero4U - 4 Port USB Hub for Raspberry Pi Zero v1.3

Product ID: 3298

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero with the Zero4U! This is a 4-port USB hub for Raspberry Pi Zero, and it can be mounted back-to-back onto a Pi Zero. The 4 pogo pins on the back will connect the PP1, PP6, PP22 and PP23 testing pads on your Raspberry Pi Zero – no soldering required! This item...

$9.95

52 in stock

Adafruit PiRTC - PCF8523 Real Time Clock for Raspberry Pi

Product ID: 3386

This is a great battery-backed real time clock (RTC) that allows your Raspberry Pi project to keep track of time if the power is lost. Perfect for data-logging, clock-building, time-stamping, timers and alarms, etc. Equipped with PCF8523 RTC, it works great with the Raspberry Pi and has native kernel support. Works perfectly with any Raspberry Pi (or similar single...

$7.50

In stock

USB Mini Hub with Power Switch - OTG Micro-USB

Product ID: 2991

Do you ever find yourself saying, "Gee whiz I wish I could plug in 4 more USB devices to my tablet, or microcontroller with USB host, or a Pi Zero?" I did - literally every single day. But then I found this Micro USB powered hub and stopped having to repeat myself! This mini USB hub has four USB 2.0 ports each with a max total transmission speed up to 480 MBps. All...

$5.95

In stock

Adafruit RP2040 Prop-Maker Feather with I2S Audio Amplifier

Product ID: 5768

The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. By picking a feather and stacking on a FeatherWing you can create advanced projects quickly. One popular combo is our Feather M4 or Feather RP2040 with a Prop-Maker FeatherWing on top to create animatronics or props that boot up instantly and can drive...

$19.95

In stock

Raspberry Pi 4 Model B - 8 GB RAM

Product ID: 4564

$75.00

In stock

Angled shot of Raspberry Pi Zero W computer with headers.

Raspberry Pi Zero WH (Zero W with Headers)

Product ID: 3708

If you didn't think that the Raspberry Pi Zero W could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero WH offers all the benefits of the Pi Zero W, but with one big difference – a pre-soldered GPIO header! This upgrade is the addition of a BCM43143 WiFi chip BUILT-IN to your Raspberry Pi Zero – just like...

$16.00

In stock

Adafruit I2S Stereo Decoder - UDA1334A Breakout

Product ID: 3678

This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface. It's affordable but sounds great! The NXP UDA1334A is a jack-of-all-I2S-trades: you can use 3.3V - 5V logic levels (a rarity) and can process multiple different formats by setting two pins to high or low. The DAC will process data immediately and give you a...

$6.95

In stock

Angled shot of a rectangular black and clear acrylic case.

Adafruit Raspberry Pi Zero Case

Product ID: 3252

This is a basic, classic Pi Zero enclosure with a black base and a clear top. The case is as minimal as it gets, coming in just two pieces of polycarbonate that snap snugly together. This case will keep your Pi Zero safe and secure while also looking super sleek. You can use all of the connectors on the edges of the Pi: mini HDMI, microSD slot, microUSB power, and...

$4.75

In stock

Top view of assembled and powered on Adafruit PiOLED - 128x32 Monochrome OLED on a Pi Zero. The OLED displays a data readout.

Adafruit PiOLED - 128x32 Monochrome OLED Add-on for Raspberry Pi

Product ID: 3527

If you're looking for the most compact li'l display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit 128x32 PiOLED is your little OLED pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The PiOLED comes with a monochrome 128x32 OLED, with sharp white pixels. The OLED uses...

$14.95 $7.99

In stock

Partially assembled Red and whit Raspberry Pi Foundation Raspberry Pi 4 Case.

Official Raspberry Pi Foundation Raspberry Pi 4 Case - Red White

Product ID: 4301

Keep your Raspberry Pi® 4 Model B computer safe and snug in this solid ABS acrylic enclosure. You can even pick up an official case fan + heatsink kit to super-charge your Pi 4 projects and keep them cool even under computational intensity. This case keeps your Pi secure, has labeled holes for connector access, and even comes with four little bumper feet. You can...

$6.00

In stock

Angled shot of Raspberry Pi 5 connected to HQ camera.

Raspberry Pi 5 FPC Camera Cable - 22-pin 0.5mm to 15-pin 1mm - 200mm long

Product ID: 5818

This 200mm long camera cable is specifically designed to work with the Raspberry Pi 5 series. Just plug it into your Pi 5's camera port and then the other end into one of the official Pi Cameras for photo and video joy. Raspberry Pi 5 provides two four-lane MIPI connectors, each of which can support either a camera or a display. These connectors use the same 22-way,...

$1.00

80 in stock

PoE Adapter connected to Raspberry Pi and PoE hub

PoE Splitter with USB Type C - 5V 2A - 100 MB Ethernet

Product ID: 4552

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different...

$14.95

44 in stock

Angled Shot of the Raspberry Pi-branded A2-Class (32GB) SD Card.

Official Raspberry Pi A2-Class microSD Card - 32GB Blank

Product ID: 6010

Optimise data transfer speeds on your Raspberry Pi computer with an official Raspberry Pi 32GB microSD card. Rigorously tested to ensure optimal performance on Raspberry Pi computers, these Class A2 microSD cards help ensure you get the smoothest user experience from your device. Pre-formatted to FAT32, so it works out of the packaging with our projects. Ideal for...

$9.95

In stock

Official Raspberry Pi Micro HDMI to HDMI Cable - 1 meter long

Product ID: 4302

We're now stocking a very fancy Official Raspberry Pi Micro HDMI to HDMI cable with overmolding and Pi logo! It has nice molded grips for easy installation, and is 1 meter long. Perfect for use with your new Raspberry Pi 4 and playing with dual screen setup (you'll need one per Micro HDMI port) Please note that these molded connectors are a little chunkier than many...

$8.95

In stock

Mini Bluetooth Keyboard – Black

Product ID: 3601

Sure, you have a keyboard. Maybe it's wireless. Maybe it's even Bluetooth. But do you have a mini Bluetooth keyboard? Like Halloween candy, this keyboard is fun-size! If Shakespeare had this wee chiclet keyboard back in the day, he definitely would've remarked, "And though it be but little, it is fierce!" We got one of these with a DIY 'tele-prompter' kit and thought...

$12.95

73 in stock

angled shot of green, rectangular add-on board with short FPC ribbon cable.

Raspberry Pi M.2 HAT+

Product ID: 5902

The Raspberry Pi M.2 HAT+ lets you connect M.2 M Key peripherals, such as NVMe drives and AI accelerators, to Raspberry Pi 5. Features and warnings Supports single-lane PCIe 2.0 for high-speed data transfer. Supports fast ~450MBps data transfer to and from NVMe SSD drives and other PCIe accessories. Conforms to Raspberry Pi HAT+ specification. Autodetected by latest...

$10.00

In stock

Micro HDMI to HDMI Cable - 2 meter

Product ID: 1322

Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 2 meter long (about 6 feet). This is a HDMI 1.3 cable. Works great with a BeagleBone or Raspberry Pi 4 Micro HDMI to HDMI Cable - 2 meter (0:47)

$8.95

25 in stock

Break-away 0.1" 2x20-pin Strip Dual Male Header

Product ID: 2822

If we could eat headers, we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip male header is a great way to add pins to 2x20 0.1" holes in a PCB. They're also perfect companion piece to our 2x20-pin right-angle female header.

$0.95

In stock

Micro USB to Micro USB OTG Cable - 10-12" / 25-30cm long

Product ID: 3610

This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in another USB device. For example, a Pi Zero or Pi Zero W has a OTG port, as does the Arduino Zero, and anything with an ATSAMD21 that is in USB host mode. Also...

$1.95

65 in stock

Angled shot of white, square-shaped USB hub.

Raspberry Pi USB 3 Hub - 5 Gbit/s USB 3.2 Gen1

Product ID: 6012

The Raspberry Pi USB 3 Hub provides extra connectivity for your USB devices, turning one USB-A port into four. Inside it uses the Infineon CYUSB3340 for 5 Gbit/s USB 3.2 Gen1 support An optional external USB-C power input supports high-power peripherals, you can use the official Raspberry Pi USB C Power Supply for that. For lower-power peripherals, no external power...

$12.00

22 in stock

Raspberry Pi AI Kit with M.2 HAT and Hailo AI Module

Product ID: 5979

The Raspberry Pi AI Kit bundles the Raspberry Pi M.2 HAT+ with a Hailo AI acceleration module for use with Raspberry Pi 5. It provides an accessible, cost-effective, and power-efficient way to integrate high-performance AI. The AI module is a 13 tera-operations per second (TOPS) neural network inference accelerator built around the Hailo-8L chip. The module uses the...

$70.00

19 in stock

Raspberry Pi Zero FPC Camera Cable - 30cm long

Product ID: 5211

This 30cm long camera cable is specifically designed to work with the Raspberry Pi Zero series (including Zero W and Zero WH) Just plug it into your Pi Zero's camera port and then the other end into one of the official Pi Cameras for photo and video joy. Please note: Neither the Raspberry Pi Zero nor the Raspberry Pi camera is included! If you're looking to buy a...

$3.95

In stock

Vertical Wall Power Supply with USB C - 5V 3A Output and Switch

Product ID: 5801

We love the Raspberry Pi 4 and 5, with their fancy new USB Type C power connectors. Now we have an even better power supply that can be used with either Pi 4 or even a Pi 5 with 5V output, 3A of current to handle builds with accessories and displays. The vertical-style plug wont take up extra ports on your power strip, and the handy on/off switch at the end will cut...

$5.95

In stock

Zero4U - 4-Port USB Hub without Pogo Pins - v1.3

Product ID: 4115

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero, or any other single-board computer with the Zero4U! This is a 4-port USB 2.0 hub, almost identical to this one, but without the ferrite bead, standoffs or pogo pins. This might be a preferable format if you want to mount it on the bottom or side-by-side or with...

$6.95

In stock

Angled shot of 25cm long FPC ribbon cable.

40-pin 0.5mm pitch FPC Flex Cable with A-B Connections - 25cm long

Product ID: 4933

Use this 25 cm long cable with our 40-pin FPC to 2x20 IDC Plug and Socket adapter PCBs to extend your Raspberry Pi's GPIO capabilities. Note you'll have to keep an eye on where Pin 1 is on the ribbon cable, on the adapter PCBs, and your HAT or Bonnet of choice. Works great with any two of the following: 40-pin FPC to Straight 2x20 IDC Male Plug Header. 40-pin FPC to...

$0.95

In stock

Angled shot of black rectangular microcontroller with USB C and USB A connectors at both ends.

Adafruit Feather RP2040 with USB Type A Host

Product ID: 5723

You're probably really used to microcontroller boards with USB, but what about a dev board with two? Two is more than one, so that makes it twice as good! And the Adafruit Feather RP2040 with USB Host is definitely double-the-fun of our other Feather RP2040 boards, with a USB Type A port on the end for connecting USB devices to. Now you might be thinking "hey...

$17.50

In stock

Raspberry Pi Model 3 A+

Product ID: 4027

The Raspberry Pi 3 Model A+ is the latest board for the minimalist Pi fan. Like the Raspberry Pi 3 Model B+, it boasts a 64-bit quad core processor running at 1.4 GHz, dual-band 2.4 GHz and 5 GHz wireless LAN, and Bluetooth 4.3/BLE. This low-cost Pi uses the same processor as the model 3 B+, but does away with the Ethernet jack and three of the USB ports. It's still...

$25.00

In stock

Angled shot of Raspberry Pi camera board case.

Adafruit Raspberry Pi Camera Board Case with 1/4" Tripod Mount

Product ID: 3253

This is a basic, classic Adafruit Raspberry Pi Camera Board Enclosure with a black base and a clear top. The case is as minimal as it gets, coming in just two pieces of polycarbonate that snap snugly together. This case will keep your Pi Camera safe and secure while also looking super sleek. Works with Pi Camera v1 and v2. The enclosure was designed by Mike Doell...

$2.95

In stock

Raspberry Pi Zero W

Product ID: 3400

If you didn't think that the Raspberry Pi Zero could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero W offers all the benefits of the Pi Zero v1.3, but with one big difference – built-in WiFi! More specifically, this giant upgrade is the addition of a BCM43143 WiFi chip BUILT-IN to your Raspberry Pi Zero...

$15.00

In stock

Flirc Aluminum Case for Raspberry Pi 4

Product ID: 4553

We dig the sleek lines and satisfying heft of this aluminum case. Handsomely designed and thoughtfully constructed with a built-in heat sink, this Flirc enclosure boasts both form and function. The sides are aluminum, and the top and bottom are soft silicone for a nice and easy-to-clean case that looks great next to your A/V system. Included are rubber feet to raise...

$14.95

81 in stock

3.5mm (1/8") Stereo DIY Plug

Product ID: 1800

$0.95

In stock

Adafruit Feather RP2040 SCORPIO - 8 Channel NeoPixel Driver

Product ID: 5650

If there is one thing Adafruit is known for, its mega-blinky-fun-rainbow-LEDs. We just love sticking NeoPixels anywhere and everywhere. When we saw the new 'PIO' peripheral on the RP2040 from Raspberry Pi, we just knew it would be perfect for driving large quantities of NeoPixels. So we created this board, the Adafruit Feather RP2040 SCORPIO, designed specifically...

$14.50

In stock

Mini HDMI Plug to Standard HDMI Jack Adapter

Product ID: 2819

What an adorable little pug! Sorry - plug! What an adorable mini HDMI to HDMI plug. We find this plug adapter really helpful. It's a great way to convert any mini HDMI plug to a normal HDMI plug and...that's about it! Now you can use any of your classic HDMI cables. Simple. Useful. Adorable. Note: This product may come in black or white. They are functionally the...

$2.95

In stock

Angled shot of Raspberry Pi Zero computer

Raspberry Pi Zero - Version 1.3

Product ID: 2885

At first glance, the Pi Zero isn't much. It just looks like a slimmed down version of the Raspberry Pi we know and love. But when we started to think of the possibilities - and what a well-chosen set of accessories could add - we realized the appeal. And then we saw the price...could it be true? Yes! This is the slimmest, most pared down Raspberry Pi to date. It's...

$10.00

In stock

A/V and RCA (Composite Video, Audio) Cable for Raspberry Pi

Product ID: 2881

This A/V RCA Cable for Raspberry Pi is a great way to turn your Pi 3, 2, A+ or B+'s output into a full on composite video and audio device. Simply connect the cable to your Raspberry Pi's 3.5mm jack and the other side into whatever device you're looking to connect to and get full RCA visuals and sound. We're big fans of RCA connectors. They're one of our favorite...

$4.95

In stock

GPIO Ribbon Cable 2x8 IDC Cable - 16 pins 12" long

Product ID: 4170

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Comes in a classic Adafruit Black, has a nice soft flexible 16-line 0.05" ribbon cable and keyed IDC connectors on both ends. It's perfect for use with our GPIO Expander bonnet or with any of our RGB LED Matrices if you want to chain them together or...

$1.95

In stock

Kit contents showing plastic insert, fan, and heat sink

Official Raspberry Pi 4 Case Fan and Heatsink

Product ID: 4794

The Raspberry Pi 4 Case Fan + Heatsink is compatible with the Raspberry Pi 4 and the Raspberry Pi 4 Case. Designed for anyone who wants to push the performance of their Pi, as well as overclockers and other power users, it keeps your Raspberry Pi 4 at a comfortable operating temperature even when under heavy load thanks to both a mini heatsink that goes on top of...

$5.00

81 in stock

5V 3A Switching Power Supply with USB C - RA

Wall Power Supply with USB C - 5V 3A Output and Switch

Product ID: 5802

We love the Raspberry Pi 4 and 5, with their fancy new USB Type C power connectors. Now we have an even better power supply that can be used with either Pi 4 or even a Pi 5 with 5V output, 3A of current to handle builds with accessories and displays. This flat square body works best when plugging into a wall socket so it doesn't get knocked out easily, and a handy...

$5.95

In stock

Overhead shot of kit contents for NVME kit.

Pimoroni NVMe Base for Raspberry Pi 5 - PIM699

Product ID: 5845

Pimoroni's NVMe Base brings high-speed storage to Raspberry Pi 5, and lets you use that cool new PCIe connector. This is an extension board for Raspberry Pi 5: simply plug in an M-key NVMe SSD (2230 to 2280 sizes supported) and mount it under your Pi for a compact and fast storage solution - It even comes with rubber feet! Upgrading to an NVMe disk (instead of using...

$19.95

In stock

Close up shot of Raspberry Pi Camera Module 3 Wide NoIR.

Raspberry Pi Camera Module 3 Wide NoIR - 12MP 120 Degree - Wide Angle Infrared Lens

Product ID: 5660

$35.00

70 in stock

Angled shot of 16GB Micro SD Card with NOOBS 3.1

16GB Card with NOOBS 3.1 for Raspberry Pi Computers including 4

Product ID: 4266

NOOBS 3.1 is the fastest way to have a variety of operating systems on your Pi. Available on a 16G card, you can now boot multiple OS's such as Raspbian, Pidora, RaspBMC, Snappy Ubuntu, etc. There's a boot up menu for selecting which one you like. This card has NooBs 3.1 on it, works great and has enough space for 2 or 3 simultaneous OS options! Works with any and...

$14.95

In stock

Raspberry Pi Camera Board v2 - 8 Megapixels

Product ID: 3099

Snap, snap! The Camera v2 is the new official camera board released by the Raspberry Pi Foundation! The Raspberry Pi Camera Board v2 is a high quality 8 megapixel Sony IMX219 image sensor custom designed add-on board for Raspberry Pi, featuring a fixed focus lens. It's capable of 3280 x 2464 pixel static images, and also supports 1080p30, 720p60, and 640x480p90...

$29.95

24 in stock

Angled shot of long, rectangular speaker breakout board with pre-soldered green terminal blocks.

Adafruit I2S 3W Stereo Speaker Bonnet for Raspberry Pi - Mini Kit

Product ID: 3346

Hey Mr. DJ! Turn up that Raspberry Pi mix to the max with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi. (It's not big enough to be an official HAT, so we called it a bonnet, you see?) It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi computers with a 2x20 connector - A+, B+, Zero, Pi 2, Pi 3, Pi 4, etc. We've tested it...

$12.95

In stock

angled shot of green, credit-card-sized microcontroller connected via a 500mm long FPC ribbon cable to a camera module.

Raspberry Pi 5 FPC Camera Cable - 22-pin 0.5mm to 15-pin 1mm - 500mm long

Product ID: 5820

This 500mm long camera cable is specifically designed to work with the Raspberry Pi 5 series. Just plug it into your Pi 5's camera port and then the other end into one of the official Pi Cameras for photo and video joy. Raspberry Pi 5 provides two four-lane MIPI connectors, each of which can support either a camera or a display. These connectors use the same 22-way,...

$2.50

In stock

Wall Power Supply with USB C - 5V 4A Output and Switch

Product ID: 5803

We love the Raspberry Pi 4 and 5, with their fancy new USB Type C power connectors. Now we have an even better power supply that can be used with either a Pi 4 or even a Pi 5 with 5V output and 4 Amps of current to handle builds with accessories and displays. This flat square body works best when plugging into a wall socket so it doesn't get knocked out easily, and a...

$7.95

64 in stock

Angled shot of long, skinny prototyping breakout board.

Adafruit PiCowbell Proto for Pico - Reset Button & STEMMA QT

Product ID: 5200

Ding dong! Hear that? It's the PiCowbell ringing, letting you know that the new Adafruit PiCowbell Proto is finally in stock and ready to assist your Raspberry Pi Pico and Pico W project with handy hardware and practical prototyping. The PiCowbell Proto is the same size and shape as a Pico, and is intended to socket underneath to make programming and sensor...

$1.95

In stock

Top view of Raspberry Pi HQ camera module.

Raspberry Pi High Quality HQ Camera - 12MP

Product ID: 4561

Snap, snap! There's a new official camera board released by the Raspberry Pi Foundation! The Raspberry Pi High Quality Camera is the latest camera accessory from Raspberry Pi. It offers higher resolution (12.3 megapixels, compared to 8 megapixels), and sensitivity (approximately 50% greater area per pixel for improved low-light performance) than the existing Camera...

$50.00

In stock

Top view of Raspberry Pi Pico with two 20-pin male headers.

Raspberry Pi Pico RP2040 with Loose Unsoldered Headers

Product ID: 4883

The Raspberry Pi foundation changed single-board computing when they released the Raspberry Pi computer, now they're ready to do the same for microcontrollers with the release of the brand new Raspberry Pi Pico. This low-cost microcontroller board features a powerful new chip, the RP2040, and all the fixin's to get started with embedded electronics projects at a...

$5.00

In stock

SparkFun Qwiic or Stemma QT SHIM for Raspberry Pi / SBC

Product ID: 4463

The SparkFun Qwiic or Stemma QT SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a 4-pin JST SH pin (Stemma QT or Qwiic) connector to your Raspberry Pi. The SHIM design allows you to plug directly to the Pi's I2C bus with no soldering required, and the thin PCB design allows for it to be sandwiched on your Pi GPIO with other bonnets or...

$2.50

56 in stock

USB Type C 3.1 PD to 5.5mm Barrel Jack Cable - 5V 5A Output - 1.2m long with E-Mark

Product ID: 5968

This cable will let you get rid of all those wall adapters you have stashed in the plastic bin in the basement. Instead of multiple wall warts with different power and current capabilities, this cable will convert any USB Type C power adapter with Power Delivery (PD) support into a 5V DC power port, at up to 5 Amps output! Inside the cable is a PD sink negotiation...

$7.95

86 in stock

Raspberry Pi 5 FPC Camera Cable - 22-pin 0.5mm to 15-pin 1mm - 300mm long

Product ID: 5819

This 300mm long camera cable is specifically designed to work with the Raspberry Pi 5 series. Just plug it into your Pi 5's camera port and then the other end into one of the official Pi Cameras for photo and video joy. Raspberry Pi 5 provides two four-lane MIPI connectors, each of which can support either a camera or a display. These connectors use the same 22-way,...

$2.00

52 in stock

GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

Product ID: 2243

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the through-hole version of the SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header. This header is for super-slim through-hole designs. It's a custom-made, 2x20 short female header that can be used to plug a Raspberry Pi HAT onto a B+, A+, or Pi...

$1.95

In stock

Angled shot of rectangular LoRa radio dev board.

Adafruit Feather RP2040 RFM69 Packet Radio - 868 or 915MHz - RadioFruit and STEMMA QT

Product ID: 5712

This is the Adafruit Feather RP2040 RFM69 Packet Radio (868 or 915 MHz). We call these RadioFruits, our take on an microcontroller with packet radio transceiver with built-in USB and battery charging. It's an Adafruit Feather RP2040 with a RFM69HCW 900MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without...

$19.95

18 in stock

SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

Product ID: 2187

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto any modern Raspberry Pi computer with 2x20 headers It's harder to use than the Thru-Hole type headers, because you have to do some SMT soldering, but for the slickest, slimmest fit, this header is recommended! Note that because the connectors go out...

$1.95

In stock

Angled shot of a Adafruit Perma Proto Bonnet on a Pi zero

Adafruit Perma Proto Bonnet Mini Kit

Product ID: 3203

Design your own Bonnet or pHAT, attach custom circuitry and otherwise dress your Pi Zero with this jaunty prototyping Bonnet kit! To add to the Adafruit Bonnet party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected...

$4.50

In stock

Adafruit Trinkey QT2040 - RP2040 USB Key with Stemma QT

Product ID: 5056

It's half USB Key, half Adafruit QT Py, and a lotta RP2040...it's Trinkey QT2040, the circuit board with an RP2040 heart and Stemma QT legs. Folks are loving the QT Py 2040 we made, but maybe you want something plug-and-play. So we thought, hey what if we made something like that plugs right into your computer's USB port? And this is what we came up with! The PCB is...

$7.95

In stock

USB Type C Plug to Plug Adapter

Product ID: 5328

Turn any USB Type C device into a pluggable USB key with this 'plug to plug' adapter. Works with Windows / Linux computer/laptops with a USB type C port. This adapter doesn't work with Macbook laptops due to a mistake in the design: The CC1/CC2 pins should only be connected once but they are connected both times - that means that Power Delivery chips get confused and...

$4.95 $2.50

44 in stock

Overhead close-up of Raspberry Pi Camera Module 3 NoIR.

Raspberry Pi Camera Module 3 NoIR - 12MP 75 Degree Infrared Lens

Product ID: 5659

Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi. It offers an IMX708 12-megapixel sensor with HDR and features phase detection autofocus. Camera Module 3 is available in standard and wide-angle variants, both of which are available with or without an infrared cut filter. Camera Module 3 NoIR is perfect for "night vision" and infrared photography,...

$25.00

In stock

Angled shot of CSI / DSI adapter breakout board.

Adafruit CSI or DSI Cable Adapter Thingy for Raspberry Pi

Product ID: 5785

Every time someone posts on the Adafruit forums and says they wish they had a way to adapt between the 15-pin 1mm pitch Camera (CSI) or Display (DSI) connectors on big Raspberry Pi computers and the 22-pin 0.5mm pitch connectors on Pi Zero and CM4 Dev boards, we say, "Oh you mean like some sort of CSI/DSI cable adapter thingy? Yeah, we don't have one of those in...

$2.50

In stock

Full colored diagram of Raspberry Pi Pico computer.

Adafruit GPIO Reference Card for Raspberry Pi Pico

Product ID: 4901

This handy GPIO reference card is the perfect pocket-friendly go-to resource for navigating your way around the Raspberry Pi Pico. We designed a full-color pin-out diagram and printed it on card-stock so you can parse your power from your PWM and separate your SPI from your Serial UART. All the pin uses are labeled for quick reference. On the back we have a quick...

$0.50

In stock

Raspberry Pi Zero, SD card, cables, headers and case

Raspberry Pi Zero W Budget Pack - Includes Pi Zero W

Product ID: 3410

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal. The Pi Zero W Budget Pack is almost everything you need to get going with your WiFi-enabled Pi Zero W and make it a complete meal. Note: Due...

$34.50

78 in stock

Miniature 5V Cooling Fan with Molex PicoBlade Connector

Product ID: 4468

Looking for another way to keep your project cool? Hook up this 5V Mini Cooling Fan and prevent from overheating! Of course, it's also great for use with any small computer or FPGA or motor driver or anything that needs cooling. We also carry a mini 5V cooling fan with regular JST 2-pin connectors. This fan is nearly identical - it has the same fan body, but the...

$2.95

In stock

Raspberry Pi 5 - 2 GB RAM

Product ID: 6007

$50.00

In stock

Adafruit CYBERDECK HAT for Raspberry Pi 400

Product ID: 4863

Cyber-warriors, listen up here! We’ve got with some zero-day unreleased hardware we just dumpster-dived. Now you can crack kodes, and write skripts with style, thanks to the CYBERDECK HAT for Raspberry Pi 400 from Adafruit zaibatsu. This is the same hardware Kevin Mitnick used when he popped Sidewinder! Ok, maybe not, but it will definitely let you create a...

$8.95

In stock

Raspberry Pi PoE+ HAT

Product ID: 5058

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible with Raspberry Pi 3 B+...

$20.00

58 in stock

Adafruit LoRa Radio Bonnet with OLED - RFM95W @ 915MHz - RadioFruit

Product ID: 4074

The latest Raspberry Pi computers come with WiFi and Bluetooth, and now you can add even more radio options with the Adafruit Radio Bonnets! Upgrade your Raspberry Pi with a LoRa / LoRaWAN radio, so it can communicate over very long distances. These bonnets plug right into your Pi and give you long range wireless capabilities to remote nodes that may be battery...

$32.50

84 in stock

Color Coded 2x20 Header for Raspberry Pi

Color Coded Header for Raspberry Pi

Product ID: 3907

Here's a snazzy accessory for your Raspberry Pi Zero or Zero W, a color-coded 2x20 header! This Color Coded Header takes the mystery out of your Raspberry Pi's 2x20 pinout. No longer will you stare in confusion at all 40 pins, trying to count out which one you want to plug your wires into. Peep this handy color coding: Red = 5V. Yellow = 3V. Black = GND. Blue = Do...

$1.75

In stock

0.1" 2x20-pin Strip Right Angle Female Header

Product ID: 2823

If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip, right-angle female header is a perfect companion piece to our 2x20-pin Dual Male Header. It's a great way to add right-angle capability to a 2x20 pin circuit board either by attaching the right-angle male...

$1.50

In stock

Half-size breadboard with a soldered skinny green microcontroller.

Solderless Breadboard for Raspberry Pi Pico by Monk Makes

Product ID: 5422

It can be tricky to work out which pin is which when the Raspberry Pi Pico is attached to solderless breadboard. Luckily, the MonkMakes Breadboard for Pico solves this problem by labeling the Pico pins on the breadboard. This cute 3.2″ × 2.1″ (82 × 53mm) solderless half-size breadboard has four bus lines and 30 rows of pins, our favorite size...

$4.95

In stock

GPIO Female 2x2 4-pin Socket Riser Header for Raspberry Pi

GPIO Female Socket Riser Header - 2x2 4-pin

Product ID: 4855

This 0.1" inch pitch 2x2 Female Header is the perfect boost to use with boards that use the 4-pin 'PoE' header on the Raspberry Pi 3 and 4, like the Raspberry Pi PoE HAT! It's a great pairing to the 2x20 socket riser header to get a full lift. Use this wee GPIO header along with a 40-pin stacking header to utilize the PoE HAT with another add-on board. This header...

$0.50

In stock

SD Card Extender - 68cm (26 inch) long cable

Product ID: 3687

Stop fiddling with SD card sockets in the back of your latest gadget, and streeeeeeeeeetch out with an SD Card Extender . This simple, but effective device gives you a long flexible cable, a pseudo-card on one end, and an SD card socket on the other. Plug in the SD card half and attach the socket wherever you like. This is a great hack for length constraints with 3D...

$6.95

37 in stock

Angled shot of black, rectangular datalogging board.

Adafruit PiCowbell Adalogger for Pico - MicroSD, RTC & STEMMA QT

Product ID: 5703

Ding dong! Hear that? It's the PiCowbell ringing, letting you know that the new Adafruit PiCowbell Adalogger is in stock and ready to assist your Raspberry Pi Pico and Pico W project with handy hardware and datalogging. The PiCowbell Adalogger is the same size and shape as a Pico and is intended to socket underneath to make your next data logging or data reading...

$7.95

In stock

HDMI to RCA Audio and CVBS NTSC, PAL, or S-Video Converter

Product ID: 3537

Do you have a S-Video display, projector or monitor that is not compatible with your HDMI devices? Here's an adapter that will allow you to convert HDMI to S-Video, for older video devices that might not have an HDMI input. S-Video has better performance than plain "RCA" composite NTSC/PAL as it separates the color and light level, so if you have a device that can...

$34.95

62 in stock

Adafruit DVI Sock for Pico - Works with HDMI Displays

Product ID: 5957

Wouldn't it be cool to display images and graphics directly from your Pico or Pico W to an HDMI monitor or television? We think so! So we designed this DVI Sock with a digital video output (a.k.a DVI) that will work with any HDMI monitor or display. Note it doesn't do audio, just graphics! We designed this little breakout board after seeing Wren6991's Pico DVI Sock...

$2.95

65 in stock

Adafruit Mini PiTFT 1.3" - 240x240 TFT Add-on for Raspberry Pi

Product ID: 4484

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit Mini PiTFT - 1.3" 240x240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color...

$14.95

In stock

50-pin 0.5mm FFC / FPC Extender

Product ID: 4522

This 50-pin FFC / FPC Extender is very simple. It lets you connect two 50-pin 0.5mm pitch FFC (Flexible Flat Cable) / FPC (Flexible Printed Circuit) cables end-to-end and extend the length. For use with 0.3mm thick FPC cables. Note that pin 1 of one cable is connected to pin 50 of the other so you need to use a cable that has contacts on the same side (type A cable)...

$0.95

In stock

Close-up of FPC ribbon cable connecting a Raspberry Pi to a 7" touchscreen.

Raspberry Pi 5 FPC Display Cable - 22-pin 0.5mm to 15-pin 1mm - 500mm long

Product ID: 5823

This 500mm long display cable is specifically designed to work with the Raspberry Pi 5 series. Raspberry Pi 5 provides two four-lane MIPI connectors, each of which can support either a camera or a display. These connectors use the same 22-pin, 0.5mm-pitch “mini” FPC format as the Compute Module Development Kit, and require adapter cables to connect to the...

$2.50

98 in stock

Adafruit ItsyBitsy RP2040

Product ID: 4888

A new chip means a new ItsyBitsy, and the Raspberry Pi RP2040 is no exception. When we saw this chip we thought "this chip is going to be awesome when we give it the ItsyBitsy teensy-weensy Treatment" and so we did! This Itsy' features the RP2040, and all niceties you know and love about the ItsyBitsy family What's smaller than a Feather but larger than a Trinket?...

$9.95

In stock

Angled shot of 40-pin FPC connector on 2x20 socket header adapter PCB.

40-pin FPC to Straight 2x20 IDC Female Socket Header

Product ID: 4905

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a 40-pin FPC to Straight 2x20 IDC Female Socket Header Adapter Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply plug the socket side into the Raspberry Pi. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the...

$3.50

In stock

HDMI to RCA Audio and NTSC or PAL Video Adapter

Product ID: 3365

Do you have a display, television, projector or some other older device that isn't compatible with your HDMI devices? Here's an adapter that will allow you to convert HDMI from your modern computer or game system to NTSC/PAL, for older screens and devices that might not have an HDMI input. This mini HDMI to AV signal converter will convert HDMI video signal or audio...

$13.95

53 in stock

Angled shot of motor breakout board with green terminal blocks.

Adafruit DC & Stepper Motor Bonnet for Raspberry Pi

Product ID: 4280

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. We basically took our super-popular DC+Stepper Motor HAT and squeezed it down and made it fully assembled - plug and play ready to go, no soldering...

$22.50

62 in stock

A collection of electronic parts included in kit.

Raspberry Pi 400 Desktop - Full Computer Kit

Product ID: 4796

Raspberry Pi 400 is a complete Raspberry Pi 4-based personal computer, integrated into a keyboard. The Pi 4 is the first computer from the Pi Foundation that really feels 'desktop computer' speed - you can use it as an every day computer at a great price! Normally you'd need to pick up a keyboard and other accessories to turn the Pi 4 into a functioning desktop - but...

$80.00

2 in stock

Close up shot of Raspberry Pi M12 camera mount.

Raspberry Pi High Quality Camera – M12 Lens Mount

Product ID: 5661

The Raspberry Pi High Quality Camera with M12 Lens Mount offers 12.3-megapixel resolution and impressive low light performance in a compact form factor. The camera is designed to work with interchangeable M12-mount lenses (not supplied) and is suitable for integrating into industrial and consumer applications where the highest levels of visual fidelity are required....

$50.00

In stock

Pimoroni NVMe Base Duo for Raspberry Pi 5 - PIM704

Product ID: 5969

Add two super-fast NVMe SSDs to your Raspberry Pi 5! Ideal if you need redundancy or just a load more storage on your RPi. Pimoroni's NVMe Base Duo is a PCIe Gen 2 extension board for Raspberry Pi 5. To use it, simply populate it with one or two M-key NVMe SSDs (2230 to 2280 sizes supported) and mount it under (or over) your Pi for a compact and fast storage...

$34.95

In stock

Adafruit 16-Channel PWM / Servo Bonnet for Raspberry Pi

Product ID: 3416

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy bonnet! It adds the capability to control 16 Servos with perfect timing. It can also do PWM...

$12.50

43 in stock

Pimoroni Pico LiPo Power SHIM for Raspberry Pi Pico and Pico W - PIM557

Product ID: 5612

This SHIM from the Pimoroni Pirates provides a convenient way of powering your Raspberry Pi Pico from a LiPo/LiIon battery. You can recharge the battery easily by providing power to the Pico's USB port, then take your Pico or Pico W project on the go with the battery pack powering your circuitry. Solder this neat little square to the pins on the back of your Pico,...

$8.95

67 in stock

PCIe Flex Cable for NVMe Base and Raspberry Pi 5 – PCIe Pipe - 50mm

Product ID: 5931

This PCIe Flex Cable gives you a variety of options for connecting and placing your Pimoroni NVMe Base with Raspberry Pi 5. They have a 'one way' design with 16 pads at the Raspberry Pi 5 end and 18 pins at the NVMe Base end to prevent incorrect installation. The designed is set up for PCIe Gen 3 speeds and support Gen 2 perfectly fine also. The 50mm PCIe Pipe adds...

$1.95

In stock

Raspberry Pi Zero v1.3 Camera Cable

Product ID: 3157

This camera cable is specifically designed to work with the Raspberry Pi Zero - Version 1.3! Just plug it into your Pi Zero's camera port and then the other end into one of the official Pi Cameras for photo & video joy. The Raspberry Pi Zero is NOT included in this product! If you're looking to buy a Raspberry Pi Zero, check out our selection of packs here!

$5.95

In stock

Micro SD Card PCB Extender

Product ID: 4395

Stop fiddling with micro SD card sockets in the back of your latest gadget during development, and give yourself a little more elbow room with this Small Micro SD Card Extender. This is a great hack for length constraints with 3D printers, single-board computers, data-logging kits and more. Get to your micro SD card in and out without using your fingernails! Insert...

$4.50

In stock

Angled shot of black, rectangular prototyping board with two 2x20 socket headers.

Adafruit Proto Under Plate PiCowBell for Pico - Reset Button & STEMMA QT

Product ID: 5905

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed. Plug-and-play so no soldering necessary when used with a Pico H or Pico WH? Here you go! This board has double...

$4.50

In stock

Angled shot of long skinny CAN Bus microcontroller with terminal blocks.

Adafruit PiCowbell CAN Bus for Pico - MCP2515 CAN Controller

Product ID: 5728

Ding dong! Hear that? It's the PiCowbell ringing, letting you know that the new Adafruit PiCowbell CAN Bus is in stock and ready to assist your Raspberry Pi Pico and Pico W project connect to CAN bus networks for automotive or robotics projects. CAN Bus is a small-scale networking standard, originally designed for cars and, yes, busses, but is now used for many...

$12.50

In stock

Angled shot of power serial add-on board.

Adafruit PiUART - USB Console and Power Add-on for Raspberry Pi

Product ID: 3589

Here's another super handy add-on for your Raspberry Pi computer, perfect for 'head-less' setups! The PiUART adds a USB Type-C to serial connection so you can use any serial port software to connect to the Pi's console. It plugs in and is fast and easy to add whenever you need to connect to your Pi. Two LEDs connect to RX and TX on the serial converter chip so you...

$6.95

In stock

Micro B USB to USB C Adapter

Product ID: 4299

As technology changes and adapts, so does Adafruit, and speaking of adapting, this adapter has a Micro B USB jack and a USB C plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Since it uses a new connector, you may have lots of cables and power supplies that...

$1.25

In stock

Adafruit 128x64 OLED Bonnet for Raspberry Pi

Product ID: 3531

If you'd like a compact display, with buttons and a joystick - we've got what you're looking for. The Adafruit 128x64 OLED Bonnet for Raspberry Pi is the big sister to our mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger screen besides. With the OLED display in the center, we had some space on either side so we added a 5-way...

$22.50

66 in stock

Angled shot of black, rectangular doubler prototyping board.

Adafruit Proto Doubler PiCowbell for Pico and PicoW

Product ID: 5906

The Adafruit Proto Doubler PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed. Battery with recharging and on/off switch? Affirmative. Plug-and-play so no soldering necessary when used with a Pico H...

$7.50

In stock

40 Pin GPIO Extension Cable connecting Raspberry Pi 400 computer to accessory

40 Pin GPIO Extension Cable for any 2x20 Pin Raspberry Pi - 150mm / 6" long

Product ID: 4823

That new Raspberry Pi 400 computer you just got has a row of 2x20 pin headers on the right side - those are the GPIO (general purpose input/output) pins, and for those of us who like to hack electronics, they are where the real fun lies. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power...

$2.95

In stock

Zero Spy Camera for Raspberry Pi Zero - 120 Degree Focal Angle

Product ID: 5389

Is your house haunted? Or, rather, are you convinced that your house is haunted but have never been able to prove it since you've never had a camera that integrated with your Raspberry Pi Zero but was still small enough that the ghosts wouldn't notice it? Luckily, the Spy Camera for Raspberry Pi Zero is smaller than a thumbnail with a high enough resolution to see...

$14.95

81 in stock

6mm 3MP Wide Angle Lens for Raspberry Pi HQ Camera - 3MP

Product ID: 4563

This is the 6mm Wide Angle Lens, an add-on for the Raspberry Pi High Quality Camera. It has a wide field of view and a variety of uses, like CCTV applications, or of course, cat photos. Includes a thumbscrew to quickly and easily assemble onto the HQ Camera Board. Wide angle lenses are good for getting shots of a big area, for wildlife cameras, security cameras,...

$25.00

66 in stock

Raspberry Pi 5 FPC Display Cable - 22-pin 0.5mm to 15-pin 1mm - 200mm long

Product ID: 5821

This 200mm long display cable is specifically designed to work with the Raspberry Pi 5 series. Raspberry Pi 5 provides two four-lane MIPI connectors, each of which can support either a camera or a display. These connectors use the same 22-pin, 0.5mm-pitch “mini” FPC format as the Compute Module Development Kit, and require adapter cables to connect to the...

$1.00

In stock

Angled shot of black rectangular power management add-on board assembled on a green microcontroller.

Witty Pi 4 L3V7 - RTC & Power Management for Raspberry Pi

Product ID: 5705

Witty Pi is an add-on board that adds real time clock and power management to your Raspberry Pi. It can define your Raspberry Pi’s ON/OFF sequence and significantly reduce energy use. Witty Pi 4 L3V7 is the new member of the fourth generation of Witty Pi, and it is designed to work with 3.7V Lithium (ion or polymer) battery (that’s what L3V7 stands for)...

$27.50

16 in stock

USB 2.0 and Ethernet Hub - 3 USB Ports and 1 Ethernet

Product ID: 2909

One can never have enough socks, or USB ports. Add some more USB and Ethernet capability to your Raspberry Pi or, really, any kind of computer with this USB 2.0 and Ethernet Hub! This handy combo-hub has 3 USB 2.0 ports, and a AX88772A Ethernet transceiver. This chipset is really common and can be used by any Linux, Mac or Windows computer. It's particularly handy...

$17.50

7 in stock

Maker Pi Pico Base - Raspberry Pi Pico Not Included

Product ID: 5160

Cytron's Maker Pi Pico Base incorporates the most wanted Reset button for your Raspberry Pi Pico and gives you access to all GPIO pins on two 20-pin headers, with clear labels. Each GPIO is paired with an LED indicator for convenient code testing and troubleshooting. The bottom of the board even comes with a comprehensive pinout diagram showing the function of each...

$9.95

71 in stock

Pi Foundation Raspberry Pi Zero Case + Mini Camera Cable

Product ID: 3446

The first 'official' Pi Zero case from the Raspberry Pi Foundation is here in Raspberry Pi's sleek pink and white! While we've had our own classic Pi Zero case for a little while now, the Pi Foundation celebrates the release of the Pi Zero W with this impressive, well-designed effort that is definitely what we've come to expect from the folks who made the Raspberry...

$5.95

In stock

USB A/Micro Cable - 2m

Product ID: 2185

This is your standard USB A-Plug to Micro-USB cable. It's 2 meters long so you'll have plenty of cord to work with for those longer extensions. Perfect for connecting to your Raspberry Pi, Arduino Leonardo/Micro, FONA or Trinket (among other things). It's got extra beefy 24 AWG power wires so it works great for high power (1-2 Amp) computer powering. If you want...

$4.95

In stock

Zero Spy Camera for Raspberry Pi Zero

Product ID: 3508

Is your house haunted? Or, rather, are you convinced that your house is haunted but have never been able to prove it since you've never had a camera that integrated with your Raspberry Pi Zero but was still small enough that the ghosts wouldn't notice it? Luckily, the Zero Spy Camera for Raspberry Pi Zero is smaller than a thumbnail with a high enough resolution to...

$19.95

In stock

Adafruit Animated Eyes Bonnet for Raspberry Pi Mini Kit - Without Displays

Product ID: 3356

The Snake Eyes Bonnet is a Raspberry Pi accessory for driving two 128x128 pixel OLED or TFT LCD displays and also provides four analog inputs for sensors. It's perfect for making cosplay masks, props, spooky sculptures for Halloween, animatronics, robots...anything where you want to add a pair of animated eyes! This product is just the Pi Bonnet itself and some...

$7.95

45 in stock

NTSC/PAL (Television) TFT Display - 2.0" Diagonal

Product ID: 911

Yes, this is an adorable miniature television! The visible display measures only 2.0" diagonal, the TFT comes with a NTSC/PAL driver board. The display is very easy to use - simply connect 6-12VDC to the red and black wires, then connect a composite video source to the yellow and black wire. Voila, a television display! There's a little button to adjust the LED...

$39.95

47 in stock

Adafruit 1.3" Color TFT Bonnet for Raspberry Pi - 240x240 TFT + Joystick Add-on

Product ID: 4506

If you'd like a compact color display, with buttons and a joystick - we've got what you're looking for. The Adafruit 1.3" Color TFT Bonnet for Raspberry Pi is the big sister to our mini PiTFT add-ons. This bonnet has 240x240 color pixels in an IPS TFT display controlled over SPI. This display is super small, only about 1.3" diagonal, but since it is an IPS display,...

$17.50

54 in stock

Angled shot of black, square-shaped Raspberry Pi power management add-on board.

Witty Pi 4 HAT - RTC & Power Management for Raspberry Pi

Product ID: 5704

Witty Pi 4 is an add-on board that adds real-time clock and power management to your Raspberry Pi. It can define your Raspberry Pi’s ON/OFF sequence and significantly reduce energy usage. Witty Pi 4 is the fourth generation of Witty Pi, and it has these hardware resources onboard: Factory calibrated and temperature compensated real-time clock with ±2ppm...

$37.50

91 in stock

16mm 10MP Telephoto Lens for Raspberry Pi HQ Camera - 10MP

Product ID: 4562

This is the 16mm 10MP Telephoto Lens, an essential for the Raspberry Pi High Quality Camera. It has a wide field of view and a variety of uses, like CCTV applications, or of course, cat photos. Telephoto lenses are great for distance shots - especially good when you need to take photos or videos of far away cats. Includes a thumbscrew to quickly and easily assemble...

$50.00

8 in stock

Adafruit Terminal PiCowbell for Pico with Pre-Soldered Sockets - Reset Button & STEMMA QT

Product ID: 5907

Ding dong! Hear that? It's the PiCowbell ringing, letting you know that the new Adafruit Terminal PiCowbell is finally in stock and ready to assist your Raspberry Pi Pico and Pico W project with handy hardware and practical prototyping with screw terminal blocks for each and every pin. This board is ideal for when you want quick access to connect solid or stranded...

$12.50

83 in stock

Adafruit Pi Protector for Raspberry Pi Model Zero

Product ID: 2883

Now that we're carrying the Pi Zero, PaintYourDragon is back with another gorgeous laser-cut showpiece. This time he's taken a pass at a Pi Protector for Raspberry Pi Zero, not quite a full case, it will keep your Pi Zero safe and svelte. Keep your Raspberry Pi® Zero computer tidy and safe in this lovely clear acrylic enclosure. We designed this simple protector...

$4.95

In stock

Adafruit Feather RP2040 with DVI Output Port - Works with HDMI

Product ID: 5710

Wouldn't it be cool if you could display images and graphics from a microcontroller directly to an HDMI monitor or television? We think so! So we designed this RP2040 Feather that has a digital video output (a.k.a DVI) that will work with any HDMI monitor or display. Note it doesn't do audio, just graphics! It's kinda like we took our RP2040 Feather and DVI Breakout...

$14.95

46 in stock

Overhead shot of tripler prototyping board with three long, rectangular boards.

Adafruit Proto Tripler PiCowbell for Pico and PicoW

Product ID: 5967

The Adafruit Proto Tripler PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor or display connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed. Battery with recharging and on/off switch? Affirmative. Built in NeoPixel? Bien sur! EYE SPI connector?...

$9.95

In stock

Extreme closeup of black and white OLED display assembled onto Cyberdeck bonnet. The display reads: CYBDERDECK in a cyberpunk font.

Adafruit CYBERDECK Bonnet for Raspberry Pi 400

Product ID: 4862

Howdy keyboard cowboys, are you surfing the information superhighway with a Pi 400? Want a cool heads-up display, or maybe you need to wire up some NeoPixel wetware...? Well, we just fenced 12 megabytes of ram and some angled socket header from the underground hacker club next to the chatsubo, and it's a major upgrade to our extender board - now you can jack in any...

$6.95

12 in stock

Assembled red acrylic Raspberry Pi case with no lid.

Pi Model B+ / Pi 2 / Pi 3 Case Base - Red

Product ID: 2334

$5.00

8 in stock

Angled shot of a Aluminum Metal Heatsink Raspberry Pi 4 Case on a Raspberry Pi

Aluminum Metal Heatsink Raspberry Pi 4 Case - Without Fans

Product ID: 4341

Looking for a way to keep your Raspberry Pi 4 running cool and also look cool? We've got a two-birds-one-stone solution for you. This enclosure kit is absolutely perfect, is extra durable, but also terribly chic. Constructed from solid anodized aluminum, so it's got nice heft. It has slim openings for all your cables, slots for your Pi Camera and other peripherals,...

$24.95

In stock

GPIO Hammer Header kit - Solderless Raspberry Pi Connectors with installation hardware

GPIO Hammer Headers - Solderless Raspberry Pi Connectors - Male + Female + Installation Jig

Product ID: 3413

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. They come in both male and female, and use crafty little retaining nubbins to grip tightly into the holes on the PCB. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer...

$6.50

In stock

2x20 pin IDC Box Header - Raspberry Pi A+/B+/Pi 2/Pi 3/Pi 4

Product ID: 1993

This handy 2x20 IDC Box Header is the matching connector for our 40-pin GPIO Cable. By soldering this onto perf board you can run a GPIO cable from your Pi A+/B+/Pi 2/Pi 3 and Pi 4 to the socket. This is the same socket that comes with our Pi Cobbler Plus or Pi T-Cobbler Plus but without the PCBs or anything This socket only works for the Raspberry Pi Model A+/B+/Pi...

$0.75

In stock

Raspberry Pi Global Shutter Camera – CS Lens Mount

Product ID: 5702

The Raspberry Pi Global Shutter Camera captures 1456x1088 pixel images while avoiding the distortion artifacts produced by rolling shutter cameras. It is particularly helpful in situations involving fast motion or quickly varying lighting (or lightning!). It's the latest addition to Raspberry Pi's line of camera modules and is offered in the same form factor as the...

$50.00

10 in stock

Angled shot of an enamel pin resembling a raspberry

Raspberry Pi Enamel Pin

Product ID: 4752

Proudly show off your love for the one and only, Raspberry Pi! This is the official (and approved by the foundation) Raspberry Pi® enamel pin for use with educators, classrooms, workshops, Maker Faires, TechShops, Hackerspaces, Makerspaces, and around the world to reward beginners on their skill building journey!

$2.50

81 in stock

Hammer Header Female - Solderless Raspberry Pi Connector

Product ID: 3663

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero or pHAT/bonnet/HAT. Make sure to carefully read...

$3.25

68 in stock

Maker Pi RP2040 - Motor and Robot Controller

Product ID: 5129

Cytron's Maker Pi RP2040 features the new Raspberry Pi RP2040 chip embedded on a robot controller board. The board comes with a dual-channel DC motor driver, 4 servo motor ports, and 7 Grove I/O connectors. Now you can build your new robot friend while simultaneously trying out the new RP2040 chip! The onboard DC motor driver can control 2 x brushed DC motors or 1 x...

$14.95

52 in stock

Raspberry Pi Sense HAT - any Raspberry Pi with 2x20 Connector

Product ID: 2738

Control the same hardware as used in space... build your very own Astro Pi with the new Raspberry Pi Sense HAT! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘Astro Pi’. The Sense HAT has several integrated circuit based sensors can be used for many different types of experiments, applications, and...

$30.00

In stock

Angled shot of black, credit-card-sized development board.

Adafruit Metro RP2040

Product ID: 5786

Choo! Choo! This is the RP2040 Metro Line, making all station stops at "Dual Cortex M0+ mountain", "264K RAM round-about" and "16 Megabytes of Flash town". This train is piled high with hardware that complements the Raspberry Pi RP2040 chip to make it an excellent development board for projects that want Arduino-shape-compatibility or just need the extra space and...