STEMMA / STEMMA (JST PH 2mm)

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to match up with our STEMMA boards and sensors that have 3-pin connections - and the wires are even color coded! Red is power,...

Sparky the Blue Smoke Monster shows up whenever the magic smoke is let out of an electronic component. And his very favorite is whenever folks first start with electronics and robotics: wiring up a motor or solenoid or high power LED is a perfect recipe for getting that blue smoke out of an Arduino or Raspberry Pi. Why? Because these high-current devices can't be...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with male socket headers on the end For more information about JST PH...

The Adafruit STEMMA Audio Amp is a super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it...

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and STEMMA JST PH connectors on the other. You can sand down the center-nub key on the JST PH side to make it fit in a Grove connector. Chunkier JST PH connectors come with 2mm pitch, and JST SH (also...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with female socket headers on the end For more information about JST PH...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has header pins, so it could be used to connect to socket...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or...

Most low cost soil sensors are resistive style, where there's two prongs and the sensor measures the conductivity between the two. These work OK at first, but eventually start to oxidize because of the exposed metal. Even if they're gold plated! The resistivity measurement goes up and up, so you constantly have to re-calibrate your code. Also, resistive measurements...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

Hey, have you heard the good news? With Adafruit STEMMA boards you can easily and safely plug sensors and devices together, like this Adafruit STEMMA Speaker - Plug and Play Audio Amplifier. Like the name implies, it's got a class D audio amplifier on board, and our favorite little 1 Watt 8 ohm speaker. Connecting it up is easy - you only need ground, 3 to 5V power,...

*pew* *pew*! This board is like a little ray gun for infrared light, with two high powered LED outputs. When controlled with the onboard N-Channel FET driver, you'll be blasting 100mA-200mA of current pulsing through each LED for 10+ meters of range! This is the easiest way to get great IR emitter range without wiring up a bunch of parts. By using a 2mm pitch STEMMA...

STEMMA plug-and-play parts make your next project soldering-free! This is the STEMMA Non-Latching Mini Relay. It gives you power to control, and control over power. Put simply, you can now turn on and off lamps, fans, solenoids, and other small appliances that run on up to 250VAC or DC power using any microcontroller or microcomputer, with ease. No worrying about...

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! We also carry the socket 'mating' version of this cable over here. For more information about JST PH connectors, visit the JST website

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

This cable will let you turn a JST PH 4-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND. Red for V+. White for SDA. Green for SCL. Even though this is a JST PH connector, it will fit into a Seeed Grove connector and...

We've got a high-powered infrared emitter board, and a super-sensitive infrared remote receiver board - but why buy two boards when you can pick up one that does both? This board is the Adafruit Infrared Tranceiver breakout, which can transmit and receiver 940nm remote control data in one handy solder-free package. Please Note: to make this board easy to use, we have...

Plug in and glow, this Adafruit NeoPixel LED Strip with JST PH Connector has 30 total LEDs in a "60 LED per meter" spacing, and is 0.5 meters long, in classy Adafruit Black. Its not too long, but has lots of glowing action. Perfect for use with a Hallowing, or a custom design with a JST PH socket. The strips come in a 0.5 meter reel with three 100mm long wires...

Piezos make noise when you put an AC voltage across them: and the bigger the Vpp the louder they are. With your standard 3V logic microcontroller you can make 3Vpp with a PWM out, or 6Vpp differential with two complimentary outputs. But what if you want even louder? Or if you're using a piezo to sense distance using ultrasonic bounces? We found the nifty PAM8904,...

Totally 220 pieces, this 2.0mm Pitch Kit with JST-PH Connectors is a must-have for your workstation. You'll have enough sockets and plugs to fuel your maker tendencies for days on end! These connectors are really common in electronics, we use the 2 pin ones for our batteries and battery packs. The 3 pin and 4 pin are used for STEMMA connectors. The 4 pin size is even...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 3-pin 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect...

An optical reflective sensor is a composite electronic device with two elements - an IR LED and an IR photo-transistor. The IR LED blasts light, and when something bounces the light back to the photo-transistor, the transistor turns on and the amount of current flowing through it increases. This makes the sensor great at detecting when something is in front of the...

Whenever we're working with 'true analog' LED strips, that have 1-3 channels of RGB or White LEDs, we wish we had already invented to make wiring them easier: controlling these strips takes a bit of wiring since they almost always need 12VDC and driver FETs. Now, we've finally created the Adafruit NeoRGB Stemma board - which will make our lives easier, and maybe even...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector which are compatible with the JST PH 4 pin. These are the horizontal style. You can use these with any of our JST PH 4-Pin compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH compatible)....

Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. Each button comes with a candy-colored...

A year ago we designed a high-current-output Infrared Transmitter STEMMA which makes it easy to create high-powered IR LED blasters. Now we've sat down to design the other side, the super sensitive wide-range Adafruit Infrared IR Remote Receiver with two selectable IR receiver chips. We found plenty of 38KHz receiver sensors that would work nicely on this breakout...

For fans of the TMP36, we now have a very similar analog temperature sensor with a 3-pin JST connector (we call these STEMMA connectors). Unlike many of our temperature sensors, this one is analog output, not I2C, so its best used by a microcontroller with an analog input, as most microcontrollers do. These sensors are very simple to use, no libraries or complex...

This tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in...

Analog switches are a solid state alternative to relays, when you want a smaller, lower-power technology that won't wear out mechanically. As the name implies, you can use an analog switch chip to select between two analog signals, much like a mechanical switch. These chips tend to be tiny surface mount parts, so the Adafruit STEMMA Analog SPDT Switch lets anyone use...

While designing our IR decoding breakout we noticed the TSSP series of chips from Vishay, these are simpler than more 'remote control' receivers in that they don't do any filtering on the codes received: you really just get the demodulated-from-38KHz-signal output. According to Vishay, they're designed for "Reflective Sensing, Light Barriers, and Fast Proximity...

One of the perks of working at adafruit is you get to request hardware - and you'll probably get fast turnaround! One of our adafruit.io developers requested "an easy way to chain DS18B20 sensors for testing with adafruit.io's wippersnapper service" at 11:54am one Monday morning, and after a few back-and-forth's we came up with the Adafruit Chainable DS18B20 Extender...

For classic 38KHz infrared remote signal reading, we've got a lovely STEMMA IR Receiver. But if you want to read infrared signals from remotes with different carrier signals, especially when you don't know the frequency, this Adafruit TSMP96000 "Code Learning" Infrared IR Receiver Breakout has the ability to detect IR signals from 20 to 60KHz and provide the carrier...

For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching JST PH 3-Pin to Male Header Cables - 200mm, so wiring up is a cinch. Simply plug the cable in, then use the black wire to connect to your ground, white wire to the input/signal pin, and the red wire to...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. Can also be used with any STEMMA breakouts! This cable has a JST PH 4-pin on one side and alligator clips on the...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector which are compatible with the JST PH 3 pin. These are the horizontal style. You can use these with any of our JST PH 3-Pin compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). We also carry...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - which are compatible with the JST PH 4 pin. These are the vertical style. You can use these with any of our JST PH 4-Pin compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH compatibles)....

We got a big ol' blender and tossed in an ItsyBitsy M4, two NeoTrellis boards and an electret mic amp - turned on the 'mix' button and out came the NeoTrellis M4 - a super fun dev board for anyone who likes to squish buttons, see pretty lights and maybe make a tune or two. The NeoTrellis M4 is an all-in-one USB + NeoPixel + Elastomer + Audio board. It's powered by...

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER M4SK is like the Hallowing but twice as good, with two gorgeous 240x240 pixel IPS TFT displays, driven by a 120MHZ Cortex M4 processor that can pump out those pixels super fast. You'll get the same quality display as our...

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino even when you're on a budget? That's right, it's the Adafruit PyBadge LC! We wanted to see how much we could cram into a ​3 3⁄8 × ​2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. The...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

By popular request, we've upgraded our popular Trellis elastomer button kits to now have a PCB with full color NeoPixel support! You heard that right, no more single-color LEDs, you can now have any color you like under the fantastic rubbery button pads we sell. These 4x4 button pad boards are fully tile-able and communicate over I2C. With 5 address pins, you've got...

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, its the Adafruit PyBadge! We wanted to see how much we could cram into a ​3 3⁄8 × ​2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. The PyBadge is a compact board, like...

Get started with the Adafurit PyBadge LC in a jiffy with this all-in-one kit that has everything you need to make a portable, rechargeable gaming/electronics/name-tag system. What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino even when you're on a budget? That's right, it's the Adafruit PyBadge LC! We wanted to see how much we...

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for any Particle Mesh or Feather board, so that you can easily interface with Seeed's huge collection of Grove sensors. Now you can have full range of hundreds of Grove modules with Particle Mesh along with our Feather line! Working with Grove requires no soldering. Just plug the sensors,...

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, it's the Adafruit PyBadge! We wanted to see how much we could cram into a ​3 3⁄8 × ​2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. The PyBadge is a compact board, like...

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we UPPED our -skull-shaped development board game, and re-spinned (re-spun?) the HalloWing M0 into the HalloWing M4 with MORE of everything that makes this the spoooookiest dev board. Are you the kind of person who doesn't like taking...

How many times have we heard "hey you could have just replaced that microcontroller with a 555"? Maybe 555 times! But we always find wiring up a timer chip to be a bit of a pain, you need quite a few components - especially if you want a buffered output. That's why we designed the Adafruit 555 PWM Output STEMMA - a fully-assembled 555 timer board with...

Plug in and glow, this Adafruit NeoPixel LED Strip with JST PH Connector has 30 total LEDs and is 1 meter long, in classy Adafruit Black. It's not too long but has lots of glowing action. Perfect for use with a Hallowing, PyPortal, BrainCraft HAT or any other existing or custom design with a "STEMMA" 3-pin JST PH socket. The strips come in a 1-meter reel with three...

Extend and expand your Circuit Playground projects with a bolt on TFT Gizmo that lets you add a lovely color display in a sturdy and reliable fashion. This PCB looks just like a round TFT breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Once attached you'll get a 1.54" 240x240 IPS display with backlight control, two...

Machine learning has come to the 'edge' - small microcontrollers that can run a very miniature version of TensorFlow Lite to do ML computations. But you don't need super complex hardware to start developing your own TensorFlow models! We've adapted our popular PyBadge board to add a microphone so you can dip your toes into machine learning waters. It does everything...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector which are compatible with the JST PH 3 pin. These are the vertical style. You can use these with any JST PH 3-Pin or Compatible / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH compatibles). We also...

New from Adafruit, we are taking our most popular sensors and making them easier than ever to use! This is the Adafruit STEMMA TSL2561 which takes our favorite lux sensor and gives you two ways to play: you can use alligator clips to connect the sensor to your Flora, Gemma or Circuit Playground, or plug-n-play with STEMMA cables or Seeed Grove cables Each STEMMA...

Extend and expand your Circuit Playground projects with a bolt-on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and reliable fashion. This PCB looks just like a round E-Ink breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Chances are you've seen one of those new-fangled 'e-readers' like...

Discontinued - you can grab Circuit Playground 200x200 Tri-Color E-Ink Gizmo instead! Extend and expand your Circuit Playground projects with a bolt on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and reliable fashion. This PCB looks just like a round E-Ink breakout but has permanently affixed M3 standoffs that act as mechanical and...

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for many Particle Mesh or Feather board, so that you can easily interface with Seeed's huge collection of Grove sensors. Now you can have full range of hundreds of Grove modules with Particle Mesh along with our Feather line! Working with Grove requires no soldering. Just plug the...