STEMMA

STEMMA is a plug-and-play board and sensor system that lets you quickly plug together various devices and accessories, without any soldering! STEMMA uses 3-pin cables for simple analog and digital devices, like relays and buttons. For more complex sensors and displays, we use a 4-wire I2C connection. For larger boards and devices we use a Grove-compatible connector, for smaller ones we use a Qwiic-compatible connector called STEMMA QT.

As all STEMMA sensors have level shifting and voltage regulation, you can use them safely with any 3 to 5V power and logic device - from microcontrollers like Arduino-compatibles, to full Linux single board computers like the Raspberry Pi. We even have USB to I2C adapters that let you connect STEMMA devices directly to a computer without any microcontroller programming required! Then, use our Arduino or CircuitPython/Python libraries and examples to easily get your electronics project working on any platform with STEMMA and STEMMA QT.

Adafruit LIS3DH Triple-Axis Accelerometer (+-2g/4g/8g/16g)

PRODUCT ID: 2809

The LIS3DH is a very popular low power triple-axis accelerometer . It's low-cost, but has just about every 'extra' you'd want...

The LIS3DH is a very popular low power triple-axis accelerometer . It's low-cost, but has just about every 'extra' you'd want in an accelerometer: Three axis sensing, 10-bit precision±2g/±4g/±8g/±16g selectable scalingBoth I2C (2 possible addresses) and SPI interface optionsInterrupt outputMultiple data rate options 1 Hz to 5KhzAs low as 2uA current draw (just the chip itself, not including any...

$4.95

95 IN STOCK

Adafruit NeoPixel LED Strip with 3-pin JST PH Connector lit up rainbow

Adafruit NeoPixel LED Strip with 3-pin JST PH Connector - 60 LED/meter / 0.5 Meter

PRODUCT ID: 3919

Plug in and glow, this Adafruit NeoPixel LED Strip with JST PH Connector has 30 total LEDs in a "60 LED per meter" spacing , and is 0.5...

Plug in and glow, this Adafruit NeoPixel LED Strip with JST PH Connector has 30 total LEDs in a "60 LED per meter" spacing , and is 0.5 meters long, in classy Adafruit Black. Its not too long, but has lots of glowing action. Perfect for use with a Hallowing, or a custom design with a JST PH socket. The strips come in a 0.5 meter reel with three 100mm long wires connected to a JST PH 3-pin plug . The other end is sealed. The wires are...

$12.50

IN STOCK

Adafruit MCP2221A Breakout - General Purpose USB to GPIO ADC I2C - Stemma QT / Qwiic

PRODUCT ID: 4471

Wouldn't it be cool to drive a tiny OLED display, read a color sensor, or even just flash some LEDs directly from your computer? Sure...

Wouldn't it be cool to drive a tiny OLED display, read a color sensor, or even just flash some LEDs directly from your computer? Sure you can program an Arduino or Trinket to talk to these devices and your computer, but why can't your computer just talk to those devices and sensors itself? Well, now your computer can talk to devices using the Adafruit MCP2221A breakout board! What can the MCP2221 chip do?...

$6.50

IN STOCK

Adafruit Feather RP2040

PRODUCT ID: 4884

A new chip means a new Feather, and the Raspberry Pi RP2040 is no exception. When we saw this chip we thought "this chip is going to be awesome...

A new chip means a new Feather, and the Raspberry Pi RP2040 is no exception. When we saw this chip we thought "this chip is going to be awesome when we give it the Feather Treatment" and so we did! This Feather features the RP2040 , and all niceties you know and love about Feather Lots are being made, if we're temporarily out of stock please sign up to be notified as soon as we manufacture more! Measures 2.0" x 0.9"...

$11.95

IN STOCK

JST PH 3-Pin Socket to Color Coded Cable - 200mm

PRODUCT ID: 4046

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for...

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! We also carry the socket 'mating' version of this cable over here. For more information about JST PH connectors, visit the JST website

$0.95

IN STOCK

Adafruit I2C QT Rotary Encoder with NeoPixel - STEMMA QT / Qwiic

PRODUCT ID: 4991

Rotary encoders are soooo much fun! Twist em this way, then twist them that way. Unlike potentiometers, they go all the way around, and often have...

Rotary encoders are soooo much fun! Twist em this way, then twist them that way. Unlike potentiometers, they go all the way around, and often have little detents for tactile feedback. But, if you've ever tried to add encoders to your project you know that they're a real challenge to use: timers, interrupts, debouncing... This Stemma QT breakout makes all that frustration go away - solder in any 'standard' PEC11-pinout rotary...

$5.95

IN STOCK

Adafruit QT Py - SAMD21 Dev Board with STEMMA QT

PRODUCT ID: 4600

What a cutie pie! Or is it... a QT Py? This diminutive dev board comes with our favorite lil chip, the SAMD21 (as made famous in our GEMMA M0 and...

What a cutie pie! Or is it... a QT Py? This diminutive dev board comes with our favorite lil chip, the SAMD21 (as made famous in our GEMMA M0 and Trinket M0 boards). This time it comes with our favorite connector - the STEMMA QT, a chainable I2C port that can be used with any of our STEMMA QT sensors and accessories. OLEDs! Inertial Measurment Units! Sensors a-plenty. All plug-and-play thanks to the innovative chainable design: SparkFun...

$7.50

IN STOCK

Adafruit FeatherWing OLED - 128x64 OLED Add-on For Feather - STEMMA QT / Qwiic

PRODUCT ID: 4650

A Feather board without ambition is a Feather board without FeatherWings! This is the FeatherWing 128x64 OLED : it adds a gorgeous 128x64...

A Feather board without ambition is a Feather board without FeatherWings! This is the FeatherWing 128x64 OLED : it adds a gorgeous 128x64 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight! These displays are small, only about 1.3" diagonal,...

$14.95

IN STOCK

INA219 High Side DC Current Sensor Breakout - 26V ±3.2A Max - STEMMA QT

PRODUCT ID: 904

This breakout board will solve all your power-monitoring problems. Instead of struggling with two multimeters, you can just use the handy INA219B...

This breakout board will solve all your power-monitoring problems. Instead of struggling with two multimeters, you can just use the handy INA219B chip on this breakout to both measure both the high side voltage and DC current draw over I2C with 1% precision. Most current-measuring devices such as our current panel meter are only good for low side measuring. That means that unless you want to get a battery involved, you have to stick the...

$9.95

IN STOCK

Adafruit MCP4728 Quad DAC with EEPROM - STEMMA QT / Qwiic

PRODUCT ID: 4470

If you've ever said to yourself, "Gee, I wish I had four 12-bit DACs that came in a single package with the ability to save their settings...

If you've ever said to yourself, "Gee, I wish I had four 12-bit DACs that came in a single package with the ability to save their settings to an EEPROM", well I have good news. The MCP4728 is the answer to your wishes! Within its little package, the MCP4728 has four 12-bit DACs for whatever voltage setting needs you may have. In addition, it has the ability to store the settings for the DACs to an internal EEPROM. Once saved to the...

$7.50

7 IN STOCK

Adafruit TDK InvenSense ICM-20948 9-DoF IMU (MPU-9250 Upgrade) - STEMMA QT / Qwiic

PRODUCT ID: 4554

When you want to sense orientation using inertial measurements, you need an Inertial Measurement Unit, and when it comes to IMUs, the more DoFs, the...

When you want to sense orientation using inertial measurements, you need an Inertial Measurement Unit, and when it comes to IMUs, the more DoFs, the better! The ICM20948 from Invensense packs 9 Degrees of freedom into a teeny package, making it a one-stop-shop for all the DOFs you need! Within its svelte 3x3mm package, there is not just one MEMS sensor die like your common sensors, but two sensor dies! The ICM20948 pair’s...

$14.95

IN STOCK

Adafruit TSL2591 High Dynamic Range Digital Light Sensor with stemma QT

Adafruit TSL2591 High Dynamic Range Digital Light Sensor - STEMMA QT

PRODUCT ID: 1980

When the future is dazzlingly-bright, this ultra-high-range luminosity sensor will help you measure it. The TSL2591 luminosity sensor is an advanced...

When the future is dazzlingly-bright, this ultra-high-range luminosity sensor will help you measure it. The TSL2591 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from 188 uLux up to 88,000 Lux on the fly. The best...

$6.95

IN STOCK

Adafruit QT Py RP2040

PRODUCT ID: 4900

What a cutie pie! Or is it... a QT Py? This diminutive dev board comes with one of our new favorite chip, the RP2040. It's been made famous...

What a cutie pie! Or is it... a QT Py? This diminutive dev board comes with one of our new favorite chip, the RP2040. It's been made famous in the new Raspberry Pi Pico and our Feather RP2040 and ItsyBitsy RP2040, but what if we wanted something really smol? A new chip means a new QT Py, and the Raspberry Pi RP2040 is no exception. When we saw this chip we thought "this chip is going to be awesome when we give it the cuuutie QT Py...

$9.95

IN STOCK

Adafruit Sensirion SHT31-D Humidity sensor

Adafruit Sensirion SHT31-D - Temperature & Humidity Sensor

PRODUCT ID: 2857

Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that...

Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT31-D sensor has an excellent ±2% relative humidity and ±0.3°C accuracy for most uses. We now use the version with a PTFE filter, it'll stay clean while still allowing humidity measurements to work Unlike earlier SHT...

$13.95

IN STOCK

Soil sensor in small potted plant, with wires connected to Adafruit Metro

Adafruit STEMMA Soil Sensor - I2C Capacitive Moisture Sensor

PRODUCT ID: 4026

Most low cost soil sensors are resistive style, where there's two prongs and the sensor measures the conductivity between the two. These work OK...

Most low cost soil sensors are resistive style, where there's two prongs and the sensor measures the conductivity between the two. These work OK at first, but eventually start to oxidize because of the exposed metal. Even if they're gold plated! The resistivity measurement goes up and up, so you constantly have to re-calibrate your code. Also, resistive measurements don't always work in loose soil. This design is superior with a...

$7.50

IN STOCK

Adafruit AHT20 - Temperature & Humidity Sensor Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 4566

The AHT20 is a nice but inexpensive temperature and humidity sensor from the same folks that brought us the DHT22. You can take sensor readings as...

The AHT20 is a nice but inexpensive temperature and humidity sensor from the same folks that brought us the DHT22. You can take sensor readings as often as you like, and it uses standard I2C so its super easy to use with any Arduino or Linux/Raspberry Pi board. This sensor has a typical accuracy of +- 2% relative humidity, and +-0.3 °C at 20-80% RH and 20-60 °C. There is only one I2C address so it's not a good option when you need...

$4.50

IN STOCK

Monochrome 1.3" 128x64 OLED graphic display - STEMMA QT / Qwiic

PRODUCT ID: 938

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of...

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$19.95

IN STOCK

Adafruit BH1750 Light Sensor with STEMMA QT / Qwiic

Adafruit BH1750 Light Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4681

This is the BH1750 16-bit Ambient Light Sensor from Rohm. Because of how important it is to humans and most other living things, sensing the amount...

This is the BH1750 16-bit Ambient Light Sensor from Rohm. Because of how important it is to humans and most other living things, sensing the amount of light in an environment is a common place to get started when learning to work with microcontrollers and sensors. Should we turn up the brightness of our display or dim it to save power? Which direction should your robot move to stay in an area with the most light? Is it day or night? All of these...

$4.50

IN STOCK

Adafruit Trinkey QT2040 - RP2040 USB Key with Stemma QT

PRODUCT ID: 5056

It's half USB Key, half Adafruit QT Py, and a lotta RP2040 ... it's Trinkey QT2040 , the circuit board with an RP2040 heart and...

It's half USB Key, half Adafruit QT Py, and a lotta RP2040 ... it's Trinkey QT2040 , the circuit board with an RP2040 heart and Stemma QT legs. Folks are loving the QT Py 2040 we made, but maybe you want something plug-and-play. So we thought, hey what if we made something like that plugs right into your computer's USB port? And this is what we came up with! The PCB is designed to slip into any USB A port on a computer or...

$7.50

IN STOCK

Adafruit BME688 - Temperature, Humidity, Pressure and Gas Sensor - STEMMA QT

PRODUCT ID: 5046

The long-awaited BME688 from Bosch gives you all the environmental sensing you want in one small package. This little sensor...

The long-awaited BME688 from Bosch gives you all the environmental sensing you want in one small package. This little sensor contains temperature , humidity , barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price! The BME688 is a 'drop in' replacement for the BME680 - it adds a method of programming the gas-sensor heater for controlled odor-analysis but...

$19.95

IN STOCK

STEMMA JST PH 3-Pin to Female Socket Cable - 200mm

PRODUCT ID: 3894

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end....

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with male socket headers on the end For more information about JST PH connectors, visit the JST website

$1.25

IN STOCK

Adafruit ST25DV16K I2C RFID EEPROM Breakout - STEMMA QT / Qwiic

PRODUCT ID: 4701

This RFID tag is really unique: it works with mobile phones just like other RFID tags, but you can reprogram it over I2C. The tag shows up as an...

This RFID tag is really unique: it works with mobile phones just like other RFID tags, but you can reprogram it over I2C. The tag shows up as an ISO/IEC 15693 (13.56MHz) chip which is readable by phones and tablets. This could be interesting in situations where you want a tag that can be re-written dynamically when connected to a controller. For example, we did a test where we had a microcontroller write different URLs a few seconds apart,...

$3.95

IN STOCK

JST PH 4-Pin to Female Socket Cable - I2C STEMMA Cable - 200mm

PRODUCT ID: 3950

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or headers. The wires are even color coded: Black for GNDRed for...

$1.50

IN STOCK

Adafruit DS3231 Precision RTC - STEMMA QT

PRODUCT ID: 5188

The datasheet for the DS3231 explains that this part is an "Extremely Accurate I²C-Integrated RTC/TCXO/Crystal". And, hey, it does...

The datasheet for the DS3231 explains that this part is an "Extremely Accurate I²C-Integrated RTC/TCXO/Crystal". And, hey, it does exactly what it says on the tin! This Real Time Clock (RTC) is the most precise you can get in a small, low-power package. We've had a breakout board version of this RTC for a while, but we want to make it even easier for folks to use, so now it comes with STEMMA QT connectors for plug-and-play...

$13.95

IN STOCK

JST PH 3-pin Plug-Plug Cable - 100mm long

PRODUCT ID: 4336

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact...

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to match up with our STEMMA boards and sensors that have 3-pin connections - and the wires are even color coded! Red is power, ground is black and signal is white. The 3 wires are 22AWG...

$0.75

IN STOCK

Adafruit Triple-axis Magnetometer - LIS3MDL - STEMMA QT / Qwiic

PRODUCT ID: 4479

Sense the magnetic fields that surround us with this handy triple-axis magnetometer (compass) module. Magnetometers can sense where the strongest...

Sense the magnetic fields that surround us with this handy triple-axis magnetometer (compass) module. Magnetometers can sense where the strongest magnetic force is coming from, generally used to detect magnetic north, but can also be used for measuring magnetic fields. This sensor tends to be paired with a 6-DoF (degree of freedom) accelerometer/gyroscope to create a 9-DoF inertial measurement unit that can detect its orientation in real-space...

$9.95

IN STOCK

Adafruit DS3502 I2C Digital 10K Potentiometer Breakout - STEMMA QT / Qwiic

PRODUCT ID: 4286

If you're a person like me that gets exhausted turning knobs all day, the DS3502 is just the ticket to calm all your knob-turning related...

If you're a person like me that gets exhausted turning knobs all day, the DS3502 is just the ticket to calm all your knob-turning related troubles. Instead of having to turn knobs with your HANDS like an ANIMAL, the DS3502 I2C Digital Potentiometer allows you to let your microcontroller adjust the resistance for you! Now you can free your hands to spin your fidget spinner or eat a slice of pizza while you're on the...

$4.95

IN STOCK

Adafruit MPU-6050 6-DoF Accel and Gyro Sensor - STEMMA QT Qwiic

PRODUCT ID: 3886

I mew, you mew we all mew for IMU! The MPU-6050 is what we call "an oldie but goodie" - this popular triple-axis accelerometer...

I mew, you mew we all mew for IMU! The MPU-6050 is what we call "an oldie but goodie" - this popular triple-axis accelerometer plus gyro combo has been a staple of electronic projects for years, and we've finally gotten around to making a breakout for it! Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a...

$6.95

IN STOCK

STEMMA JST PH 3-Pin to Male Header Cable - 200mm

PRODUCT ID: 3893

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with female socket headers on the end For more information about JST PH connectors, visit the JST website

$1.25

IN STOCK

Adafruit 12-Key Capacitive Touch Sensor Breakout with Stemma QT

Adafruit 12-Key Capacitive Touch Sensor Breakout - MPR121 - STEMMA QT

PRODUCT ID: 1982

Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the...

Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the MPR121. This chip can handle up to 12 individual touchpads. The MPR121 has support for only I2C, which can be implemented with nearly any microcontroller. You can select one of 4 addresses with the ADDR pin, for a total of 48 capacitive touch pads on one I2C 2-wire bus. Using this chip is a lot...

$7.95

IN STOCK

Top view of temperature sensor breakout above an OLED display FeatherWing. The OLED display reads "MCP9808 Temp: 24.19ºC"

Adafruit MCP9808 High Accuracy I2C Temperature Sensor Breakout - STEMMA QT / Qwiic

PRODUCT ID: 5027

The MCP9808 digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over...

The MCP9808 digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any microcontroller using standard I2C. With three address jumpers on the back, you can connect up to 8 to a single I2C bus without address collisions. Best of all, a wide voltage range makes it usable...

$4.95

IN STOCK

Monochrome 0.96" 128x64 OLED Graphic Display - STEMMA QT

PRODUCT ID: 326

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64...

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$17.50

IN STOCK

JST PH 4-Pin to Male Header Cable - I2C STEMMA Cable - 200mm

PRODUCT ID: 3955

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has header pins, so it could be used to connect to socket header or breadboards. The wires are even color...

$1.50

IN STOCK

Adafruit BMP280 I2C or SPI Barometric Pressure & Altitude Sensor - STEMMA QT

PRODUCT ID: 2651

Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next...

Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuracy, and...

$9.95

IN STOCK

Angled shot of PCF8523 Real Time Clock Breakout Board.

Adafruit PCF8523 Real Time Clock Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 5189

This is a great battery-backed real time clock (RTC) that allows your microcontroller project to keep track of time even if it is reprogrammed, or if...

This is a great battery-backed real time clock (RTC) that allows your microcontroller project to keep track of time even if it is reprogrammed, or if the power is lost. Perfect for data-logging, clock-building, time stamping, timers, and alarms, etc. Equipped with PCF8523 RTC - it can run from 3.3V or 5V power & logic! We've had a breakout board version of this RTC for a while, but we want to make it even easier for folks to...

$4.95

IN STOCK

Adafruit VCNL4040 Proximity and Lux Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4161

The VCNL4040 is a handy two-in-one sensor, with a proximity sensor that works from 0 to 200mm (about 7.5 inches) and light sensor with range of...

The VCNL4040 is a handy two-in-one sensor, with a proximity sensor that works from 0 to 200mm (about 7.5 inches) and light sensor with range of 0.0125 to 6553 lux. We've all been there. That thing is close but how close? When you need to measure a small distance with reasonable accuracy, such as the rough height of particularly calm bumble bee, the VCNL4040 Proximity Sensor from Vishay can do that for you. If perchance you also...

$5.95

IN STOCK

Adafruit STEMMA Speaker - Plug and Play Audio Amplifier

PRODUCT ID: 3885

Hey, have you heard the good news? With Adafruit STEMMA boards you can easily and safely plug sensors and devices together, like this Adafruit STEMMA...

Hey, have you heard the good news? With Adafruit STEMMA boards you can easily and safely plug sensors and devices together, like this Adafruit STEMMA Speaker - Plug and Play Audio Amplifier . Like the name implies, it's got a class D audio amplifier on board, and our favorite little 1 Watt 8 ohm speaker. Connecting it up is easy - you only need ground, 3 to 5V power, and audio signal. The audio signal does not need to be AC coupled, we do...

$5.95

99 IN STOCK

Adafruit AW9523 GPIO Expander and LED Driver Breakout - STEMMA QT / Qwiic

PRODUCT ID: 4886

Expand your project possibilities, with the Adafruit AW9523 GPIO Expander and LED Driver Breakout - a cute and powerful I2C expander with a lot of...

Expand your project possibilities, with the Adafruit AW9523 GPIO Expander and LED Driver Breakout - a cute and powerful I2C expander with a lot of tricks up its sleeve. GPIO expanders work like this: you have a board with some number of GPIO but not enough for your project - maybe you need more buttons or LEDs. You could upgrade to a board with massive number of GPIO like the Grand Central, or you could pop on one of these boards. Connect it...

$4.95

IN STOCK

Adafruit BME680 - Temperature, Humidity, Pressure and Gas Sensor - STEMMA QT

PRODUCT ID: 3660

The long awaited BME680 from Bosch gives you all the environmental sensing you want in one small package. This little sensor...

The long awaited BME680 from Bosch gives you all the environmental sensing you want in one small package. This little sensor contains temperature , humidity , barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price! Like the BME280 & BMP280, this precision sensor from Bosch can measure humidity with ±3% accuracy, barometric pressure with ±1...

$18.95

IN STOCK

JST SH 4-pin Right Angle Connector (10-pack) - Qwiic Compatible

PRODUCT ID: 4208

If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST...

If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. This connector can be used with Qwiic boards and cables, to easily connect sensors and drivers from one board...

$3.95

IN STOCK

NeoKey 1x4 QT I2C - Four Mechanical Key Switches with NeoPixels - STEMMA QT / Qwiic

PRODUCT ID: 4980

The only thing better than a nice mechanical key is, perhaps, FOUR mechanical keys that also can glow any color of the rainbow - and that's...

The only thing better than a nice mechanical key is, perhaps, FOUR mechanical keys that also can glow any color of the rainbow - and that's what the Adafruit NeoKey 1x4 QT I2C Breakout will let you do! This longgg 3" x 0.8" PCB fits four Cherry MX or compatible switches and make it easy to use with a breadboard/perfboard or with a STEMMA QT (Qwiic) connector for instant I2C connectivity on any platform....

$9.95

IN STOCK

STEMMA Cable - 150mm/6" Long 4 Pin JST-PH Cable–Female/Female

PRODUCT ID: 3568

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays connected even when moved around, but clicks easy to insert & remove. We...

$0.75

IN STOCK

Adafruit AS7341 10-Channel Light and Color Sensor Breakout

Adafruit AS7341 10-Channel Light / Color Sensor Breakout - STEMMA QT / Qwiic

PRODUCT ID: 4698

The Adafruit AS7341 10-Channel Light / Color Sensor Breakout is a multi-channel spectrometer, which is a special type of light sensor that is able to...

The Adafruit AS7341 10-Channel Light / Color Sensor Breakout is a multi-channel spectrometer, which is a special type of light sensor that is able to detect not only the amount of light present but also the amounts of light within different wavelengths. This means that you can use it to detect much better than the human eye is capable of, what color or colors of light is present. The AS7341 packs within its 3x2mm footprint 16 different...

$15.95

IN STOCK

Adafruit CYBERDECK HAT for Raspberry Pi 400

PRODUCT ID: 4863

Cyber-warriors, listen up here! We’ve got with some zero-day unreleased hardware we just dumpster-dived. Now you can crack kodes, and write...

Cyber-warriors, listen up here! We’ve got with some zero-day unreleased hardware we just dumpster-dived. Now you can crack kodes, and write skripts with style, thanks to the CYBERDECK HAT for Raspberry Pi 400 from Adafruit zaibatsu. This is the same hardware Kevin Mitnick used when he popped Sidewinder! Ok, maybe not, but it will definitely let you create a stand-alone Kali deck by plugging in one of our many display HATs. We...

$8.95

IN STOCK

Adafruit PCF8591 Quad 8-bit ADC + 8-bit DAC - STEMMA QT / Qwiic

PRODUCT ID: 4648

Measuring voltage and adjusting it is what electronics is all about so you won’t get far without friends like the Adafruit PCF8591 Quad 8-bit...

Measuring voltage and adjusting it is what electronics is all about so you won’t get far without friends like the Adafruit PCF8591 Quad 8-bit ADC + 8-bit DAC combo . A nalog to D igital C onverters help by measuring an analog voltage and turning it into something a microcontroller like a Metro or Arduino can understand. If you’re using a single-board computer like a Raspberry Pi, you might not have any...

$6.50

IN STOCK

Adafruit VL53L0X Time of Flight Distance Sensor - ~30 to 1000mm

PRODUCT ID: 3317

The VL53L0X is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny invisible laser source,...

The VL53L0X is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny invisible laser source, and a matching sensor. The VL53L0X can detect the "time of flight", or how long the light has taken to bounce back to the sensor. Since it uses a very narrow light source, it is good for determining distance of only the surface directly in front of it. Unlike sonars that bounce ultrasonic...

$14.95

IN STOCK

Adafruit Grayscale 1.5" 128x128 OLED Graphic Display - STEMMA QT / Qwiic

PRODUCT ID: 4741

This OLED goes out to all the fans who want more pixels ! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one...

This OLED goes out to all the fans who want more pixels ! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one is a whopping 128x128 pixels and it even has an extra bonus - it can do grayscale pixels! Yep, you get the same crispness of a monochrome OLED but with 16 levels of grayscale. This display is a petite 1.5" diagonal, but very readable due to the high contrast of an OLED display. This display is...

$22.50

IN STOCK

Adafruit SCD-30 - NDIR CO2 Temperature and Humidity Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4867

Take a deep breath in...now slowly breathe out. Mmm isn't it wonderful? All that air around us, which we bring into our lungs, extracts oxygen...

Take a deep breath in...now slowly breathe out. Mmm isn't it wonderful? All that air around us, which we bring into our lungs, extracts oxygen from and then breathes out carbon dioxide. CO2 is essential for life on this planet we call Earth - we and plants take turns using and emitting CO2 in an elegant symbiosis. But it's important to keep that CO2 balanced - you don't want too much around, not good for humans and not good for...

$58.95

IN STOCK

Angled shot of Adafruit TCA4307 Hot-Swap I2C Buffer.

Adafruit TCA4307 Hot-Swap I2C Buffer with Stuck Bus Recovery - STEMMA QT / Qwiic

PRODUCT ID: 5159

As we've been adding STEMMA QT connectors to our breakouts and dev boards, folks have been really enjoying the simplicity and speed of...

As we've been adding STEMMA QT connectors to our breakouts and dev boards, folks have been really enjoying the simplicity and speed of plugging in I2C sensors and devices for quick iteration and design. That's all good, but I2C wasn't really designed for hot-plugging. You're kinda supposed to have everything connected once on boot and never mess with it - I2C was specified for on-board connections. And, folks who have...

$4.95

IN STOCK

Adafruit LTC4311 I2C Extender / Active Terminator Attached to a 100 foot Ethernet cable on one end. other end of cable goes to a QT Py microcontroller.

Adafruit LTC4311 I2C Extender / Active Terminator - STEMMA QT / Qwiic

PRODUCT ID: 4756

I2C stands for Inter-Integrated-Circuit communications, it's meant for short distances on a PCB or subassembly. But, hey, we're engineers,...

I2C stands for Inter-Integrated-Circuit communications, it's meant for short distances on a PCB or subassembly. But, hey, we're engineers, and we like to push the limits of technology, right? So why not try to have I2C run over a meter long cable, or even longer? Well, if you try to do that you'll quickly find that the length of the cable adds capacitance and resistance that slows down the open-drain pullups used in I2C, making it...

$7.50

IN STOCK

Adafruit PMSA003I PM2.5 Air Quality Breakout

Adafruit PMSA003I Air Quality Breakout - STEMMA QT / Qwiic

PRODUCT ID: 4632

Breathe easy, knowing that you can track and sense the quality of the air around you with this Adafruit PMSA003I Air Quality Breakout . This...

Breathe easy, knowing that you can track and sense the quality of the air around you with this Adafruit PMSA003I Air Quality Breakout . This sensor is great for monitoring air quality, in a compact plug-in format. Best of all, unlike almost all other sensors we've seen that are UART interface, this one is I2C interface , which makes it a great match for single-board Linux computers like Raspberry Pi, or even plain Arduino UNO's...

$44.95

IN STOCK

Adafruit PCT2075 Temperature Sensor with STEMMA QT / Qwiic cable plugged into a Feather showing the temperature

Adafruit PCT2075 Temperature Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4369

The Adafruit PCT2075 Temperature Sensor is a 'code compatible' drop-in replacement for a very common I2C temperature sensor, the LM75....

The Adafruit PCT2075 Temperature Sensor is a 'code compatible' drop-in replacement for a very common I2C temperature sensor, the LM75. Compared to the LM75, however, the 11-bit ADC in the PCT2075 provides more precise measurements when compared to the LM75's 9-bit ADC. Additionally, because the PCT2075 allows the address pins to work in three states (high, low, floating), you can have 27 PCT2075s on the same bus as opposed to only 8...

$4.95

IN STOCK

Adafruit Si7021 Temperature & Humidity Sensor Breakout Board - STEMMA QT

PRODUCT ID: 3251

It's summer and you're sweating and your hair's all frizzy and all you really want to know is why the weatherman said this morning that...

It's summer and you're sweating and your hair's all frizzy and all you really want to know is why the weatherman said this morning that today's relative humidity would max out at a perfectly reasonable 42% when it feels more like 77%. Enter the Si7021 Temperature + Humidity Sensor - the best way to prove the weatherman wrong! This lovely sensor for Silicon labs has ± 3% relative humidity measurements with a...

$9.95

26 IN STOCK

Adafruit TLV493D Triple-Axis Magnetometer - STEMMA QT / Qwiic

PRODUCT ID: 4366

The TLV493D 3-axis magnetometer is a great little sensor for detecting magnets in 3D . In fact, the manufacturer Infineon suggests it could be used...

The TLV493D 3-axis magnetometer is a great little sensor for detecting magnets in 3D . In fact, the manufacturer Infineon suggests it could be used to make a joystick! You could also use it for other cool things like detecting objects with magnets attached, like the lid of a box, or maybe a statue that unlocks your secret lair when placed on your mantle? The TLD493D excels at measuring nearby magnetic fields in three dimensions. It's not...

$5.95

IN STOCK

Adafruit VL6180X Time of Flight Distance Ranging Sensor (VL6180) - STEMMA QT

PRODUCT ID: 3316

The VL6180X (sometimes called the VL6180 ) is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny laser...

The VL6180X (sometimes called the VL6180 ) is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny laser source, and a matching sensor. The VL6180X can detect the "time of flight", or how long the laser light has taken to bounce back to the sensor. Since it uses a very narrow light source, it is good for determining distance of only the surface directly in front of it. Unlike sonars that...

$13.95

IN STOCK

Angled shot of Adafruit I2C Memory Breakout Board.

Adafruit 24LC32 I2C EEPROM Breakout - 32Kbit / 4 KB - Stemma QT

PRODUCT ID: 5146

If you want to store calibration values, MAC addresses, non-secure access tokens, or other unique identifiers, EEPROM storage is a great option....

If you want to store calibration values, MAC addresses, non-secure access tokens, or other unique identifiers, EEPROM storage is a great option. EEPROM is long lasting, and doesn't need to be written in pages - a single byte can be written at once (unlike with flash memory!) EEPROM storage persists even when the power goes out, and can be over-written literally one million times. Some microcontrollers, like the ATmega328, have built in...

$3.95

IN STOCK

Adafruit Mini PiTFT - 135x240 Color TFT Add-on for Raspberry Pi

PRODUCT ID: 4393

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the...

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit Mini PiTFT - 135x240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color 240x135 pixel IPS display with great visibility at all angles. The TFT...

$14.95

IN STOCK

Adafruit MCP9601 (MCP96L01) I2C Thermocouple Amplifier - STEMMA QT / Qwiic

PRODUCT ID: 5165

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The Adafruit MCP9601 I2C Thermocouple Breakout...

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The Adafruit MCP9601 I2C Thermocouple Breakout (a.k.a MCP96L01) does all that for you and can be easily interfaced with any microcontroller or single-board computer with I2C. Inside, the chip handles all the analog stuff for you, and can interface with just about any thermocouple type: K, J, T, N, S, E, B, and R types are all supported! You can also...

$14.95

IN STOCK

Adafruit MLX90640 IR Thermal Camera Breakout - 55 Degree

PRODUCT ID: 4407

You can now add affordable heat-vision to your project and with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of...

You can now add affordable heat-vision to your project and with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of IR thermal sensors. When connected to your microcontroller (or Raspberry Pi) it will return an array of 768 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for easy integration. This version has a narrow 55°x35° field...

$64.95

IN STOCK

Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor - STEMMA QT / Qwiic

PRODUCT ID: 3595

This breakout is chock full o' sensors! Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project...

This breakout is chock full o' sensors! Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project with the Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor . When connected to your microcontroller (running our library code) it can detect simple gestures (left to right, right to left, up to down, down to up are currently supported), return the amount of red, blue, green, and...

$7.50

IN STOCK

Adafruit Matrix Portal - CircuitPython Powered Internet Display

PRODUCT ID: 4745

Folks love our wide selection of RGB matrices and accessories, for making custom colorful LED displays... and our RGB Matrix Shields and FeatherWings...

Folks love our wide selection of RGB matrices and accessories, for making custom colorful LED displays... and our RGB Matrix Shields and FeatherWings can be quickly soldered together to make the wiring much easier. But what if we made it even easier than that? Like, no solder, no wiring, just instant plug-and-play? Dream no more - with the Adafruit Matrix Portal add-on for RGB Matricies , there's never been an easier way to create powerful...

$24.95

IN STOCK

Adafruit Feather STM32F405 Express

PRODUCT ID: 4382

ST takes flight in this Feather board. The new STM32F405 Feather (video) that we designed runs CircuitPython at a blistering 168MHz – our...

ST takes flight in this Feather board. The new STM32F405 Feather (video) that we designed runs CircuitPython at a blistering 168MHz – our fastest CircuitPython board ever! We put a STEMMA QT / Qwiic port on the end, so you can really easily plug and play I2C sensors. This Feather has lots of goodies: STM32F405 Cortex M4 with FPU and 1MB Flash, 168MHz speed192KB RAM total - 128 KB RAM for general usage + 64 KB program-only/cache RAM3.3V...

$39.95

IN STOCK

JST PH 3-pin Plug to Color Coded Alligator Clips Cable

PRODUCT ID: 4030

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up...

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 3-pin 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect to wires or pads like that on the Circuit Playground or...

$1.95

84 IN STOCK

Adafruit EMC2101 I2C PC Fan Controller and Temperature Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4808

Cooling fans...They're everywhere, and they serve the important purpose of keeping things cool, generally electronics. One might rightfully...

Cooling fans...They're everywhere, and they serve the important purpose of keeping things cool, generally electronics. One might rightfully think: "these fans are pretty good at moving air to keep things cool; maybe I can use one of these neat computer fans to keep my widget frosty" followed closely by throwing up one's hands in confusion at the sight of a 3 or even 4-pin connector. OK, power takes two pins but what are these...

$5.50

IN STOCK

Adafruit STEMMA Non-Latching Mini Relay

PRODUCT ID: 4409

STEMMA plug-and-play parts make your next project soldering-free! This is the STEMMA Non-Latching Mini Relay . It gives you power to...

STEMMA plug-and-play parts make your next project soldering-free! This is the STEMMA Non-Latching Mini Relay . It gives you power to control, and control over power. Put simply, you can now turn on and off lamps, fans, solenoids, and other small appliances that run on up to 250VAC or DC power using any microcontroller or microcomputer, with ease. No worrying about flyback diodes, level shifting, pin protection. The STEMMA board takes...

$5.95

IN STOCK

JST PH 4-Pin Socket to Color Coded Cable - 200mm

PRODUCT ID: 4045

This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for...

This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GNDRed for V+White for SDAGreen for SCL Even though this is a JST PH connector, it will fit into a Seeed Grove connector and have the right matching wires as well. We also carry the socket 'mating' version...

$0.95

IN STOCK

SparkFun Qwiic or Stemma QT SHIM for Raspberry Pi / SBC

PRODUCT ID: 4463

The SparkFun Qwiic or Stemma QT SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a 4-pin JST SH pin (Stemma QT or Qwiic)...

The SparkFun Qwiic or Stemma QT SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a 4-pin JST SH pin (Stemma QT or Qwiic) connector to your Raspberry Pi. The SHIM design allows you to plug directly to the Pi's I2C bus with no soldering required, and the thin PCB design allows for it to be sandwiched on your Pi GPIO with other bonnets or HATs! The Qwiic SHIM works great if you want to add a Qwiic connector to your...

$1.50

52 IN STOCK

Adafruit SGP40 Air Quality Sensor Breakout - VOC Index - STEMMA QT / Qwiic

PRODUCT ID: 4829

*sniff* *sniff* ... do you smell that? No need to stick your nose into a carton of milk anymore, you can build a digital nose with the SGP40...

*sniff* *sniff* ... do you smell that? No need to stick your nose into a carton of milk anymore, you can build a digital nose with the SGP40 Multi-Pixel Gas Sensor, a fully integrated MOX gas sensor. This is a very fine air quality sensor from the sensor experts at Sensirion, with I2C interfacing so you don't have to manage the heater and analog reading of a MOX sensor. It combines multiple metal-oxide sensing and heating elements on one...

$14.95

IN STOCK

Adafruit DPS310 Precision Barometric Pressure and Altitude Sensor

Adafruit DPS310 Precision Barometric Pressure / Altitude Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4494

How high are you right now? If you had a precision altitude sensor, you would know for sure! The DPS310 sensor from Infineon a high-precision...

How high are you right now? If you had a precision altitude sensor, you would know for sure! The DPS310 sensor from Infineon a high-precision barometric sensor, perfect for measuring altitude changes with a up to ±0.002 hPa (or ±0.02 m) precision high precision mode and ± 1 hPa absolute accuracy. That means you can know your absolute altitude with 1=meter accuracy when you set the sea-level pressure, and measure changes in...

$6.95

IN STOCK

SparkFun STEMMA QT / Qwiic breakout adapter

SparkFun STEMMA QT / Qwiic Adapter

PRODUCT ID: 4527

The SparkFun Qwiic Adapter can make any old I2C board or sensor a STEMMA QT / Qwiic-enabled one. This adapter breaks out the I2C pins from the JST SH...

The SparkFun Qwiic Adapter can make any old I2C board or sensor a STEMMA QT / Qwiic-enabled one. This adapter breaks out the I2C pins from the JST SH connectors to pins that you can easily solder with your favorite I2C-enabled device. The Qwiic Adapter has two JST SH connection ports, all on the same I2C bus. Four plated through holes are broken out for SCL, SDA, 3.3V and GND. Simple? Yes, and very effective! Features: 2 x JST SH (Qwiic /...

$1.95

IN STOCK

Adafruit ISO1540 Bidirectional I2C Isolator - STEMMA QT / Qwiic

PRODUCT ID: 4903

Sometimes you'll find yourself with an I2C bus controller on one side, and an I2C bus device on the other and you gotta keep em (electrically)...

Sometimes you'll find yourself with an I2C bus controller on one side, and an I2C bus device on the other and you gotta keep em (electrically) separated. Maybe because one is Earth-grounded, maybe because you've got some funky power monitoring setup, maybe you want to reduce noise. Whatever it is, you can use the Adafruit ISO1540 Bidirectional I2C Isolator to add full electrical isolation between two sides of an I2C bus. The chip...

$8.95

IN STOCK

Monochrome 0.91" 128x32 I2C OLED Display - STEMMA QT / Qwiic

PRODUCT ID: 4440

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32...

These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$12.50

IN STOCK

Angled shot of BMP388 temperature and pressure sensor.

Adafruit BMP388 - Precision Barometric Pressure and Altimeter - STEMMA QT

PRODUCT ID: 3966

Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, and BMP280... now we've got the next generation, the Adafruit...

Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, and BMP280... now we've got the next generation, the Adafruit BMP388 Precision Barometric Pressure sensor . As you would expect, this sensor is similar to its earlier versions but even better . The BMP388 has better precision than ever, which makes it excellent for environmental sensing or as a precision altimeter . It can even be used in either I2C and SPI...

$9.95

IN STOCK

Adafruit CCS811 Air Quality Sensor Breakout - VOC and eCO2 - STEMMA QT / Qwiic

PRODUCT ID: 3566

Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit...

Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout . This sensor from AMS is a gas sensor that can detect a wide range of Volatile Organic Compounds (VOCs) and is intended for indoor air quality monitoring. When connected to your microcontroller (running our library code) it will return a Total Volatile...

$19.95

IN STOCK

Adafruit PyBadge for MakeCode Arcade, CircuitPython, or Arduino

PRODUCT ID: 4200

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, its the Adafruit PyBadge! We wanted to...

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, its the Adafruit PyBadge! We wanted to see how much we could cram into a 3 3⁄8 × 2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. The PyBadge is a compact board, like we said, it's credit card sized. It's powered by our favorite...

$34.95

IN STOCK

Adafruit Mini GPS PA1010D wired up to a Feather with OLED via QT cable

Adafruit Mini GPS PA1010D - UART and I2C - STEMMA QT

PRODUCT ID: 4415

This miniature GPS breakout is only 1" x 1" (~ 25mm x 25mm) but houses a complete GPS/GNSS solution with both I2C and UART interfaces....

This miniature GPS breakout is only 1" x 1" (~ 25mm x 25mm) but houses a complete GPS/GNSS solution with both I2C and UART interfaces. There's even an antenna on top, so it's plug and play! Support for GPS, GLONASS, GALILEO, QZSS-165 dBm sensitivity, up to 10 Hz updatesUp to 210 PRN channels with 99 search channels and 33 simultaneous tracking channels5V friendly design and only 30mA current drawBreadboard-able, with 4 mounting...

$29.95

IN STOCK

Adafruit NeoTrellis RGB Driver PCB for 4x4 Keypad

PRODUCT ID: 3954

By popular request, we've upgraded our popular Trellis elastomer button kits to now have a PCB with full color NeoPixel support! You heard that...

By popular request, we've upgraded our popular Trellis elastomer button kits to now have a PCB with full color NeoPixel support! You heard that right, no more single-color LEDs, you can now have any color you like under the fantastic rubbery button pads we sell. These 4x4 button pad boards are fully tile-able and communicate over I2C. With 5 address pins, you've got the ability to connect up to 32 together in any arrangement you like....

$12.50

IN STOCK

Angled shot of Adafruit MagTag development board with ESP32-S2 and E-Ink display.

Adafruit MagTag - 2.9" Grayscale E-Ink WiFi Display

PRODUCT ID: 4800

The Adafruit MagTag combines the new ESP32-S2 wireless module and a 2.9" grayscale E-Ink display to make a low-power IoT display that can show...

The Adafruit MagTag combines the new ESP32-S2 wireless module and a 2.9" grayscale E-Ink display to make a low-power IoT display that can show data on its screen even when power is removed! The ESP32-S2 is great because it builds on the years of code and support for the ESP32 and also adds native USB support so you can use this board with Arduino or CircuitPython! We designed this board to be low-power friendly - with a spot for a 350 or...

$34.95

IN STOCK

Extreme closeup of black and white OLED display assembled onto Cyberdeck bonnet. The display reads: CYBDERDECK in a cyberpunk font.

Adafruit CYBERDECK Bonnet for Raspberry Pi 400

PRODUCT ID: 4862

Howdy keyboard cowboys, are you surfing the information superhighway with a Pi 400? Want a cool heads-up display, or maybe you need to wire up some...

Howdy keyboard cowboys, are you surfing the information superhighway with a Pi 400? Want a cool heads-up display, or maybe you need to wire up some NeoPixel wetware...? Well, we just fenced 12 megabytes of ram and some angled socket header from the underground hacker club next to the chatsubo, and it's a major upgrade to our extender board - now you can jack in any Pi bonnet into the back of your Pi 400's skull at a cool angle, perfect...

$6.95

IN STOCK

JST PH 2.0mm Pitch Connector Kit with many connectors and contacts in opened box

JST PH 2.0mm Pitch Connector Kit - 220 Piece Kit

PRODUCT ID: 4422

Totally 220 pieces, this JST-PH Connector Kit is a must-have for your workstation. You'll have enough sockets and plugs to...

Totally 220 pieces, this JST-PH Connector Kit is a must-have for your workstation. You'll have enough sockets and plugs to fuel your maker tendencies for days on end! These connectors are really common in electronics, we use the 2 pin ones for our batteries and battery packs. The 3 pin and 4 pin are used for STEMMA connectors. The 4 pin size is even compatible with Grove! They are large enough you can crimp without...

$8.95

IN STOCK

Adafruit LTR390 UV Light Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4831

The LTR390 is one of the few low-cost UV sensors available, and it's a pretty nice one! With both ambient light and UVA sensing with a peak...

The LTR390 is one of the few low-cost UV sensors available, and it's a pretty nice one! With both ambient light and UVA sensing with a peak spectral response between 300 and 350nm. You can use it for measuring how much sun you can get before needing to covering up. Unlike the Si1145, this sensor will not give you UV Index readings. However, the Si1145 does UV Index approximations based on light level not true UV sensing. The LTR-390,...

$4.95

IN STOCK

Top view of humidity breakout above an OLED display FeatherWing. The OLED display reads: "HTU31 Demo Temp: 24.19ºC Hum: 37.13%"

Adafruit HTU31 Temperature & Humidity Sensor Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 4832

The HTU31-D is the third generation of temperature-humidity sensors from TE - and a great follow-up to the popular HTU21-D sensor. Like the HTU21,...

The HTU31-D is the third generation of temperature-humidity sensors from TE - and a great follow-up to the popular HTU21-D sensor. Like the HTU21, the '31 is great for sensing temperature and humidity, with excellent specifications. This I2C digital humidity sensor is an accurate and intelligent alternative to the common DHT-series sensors, at about the same price! It has a typical accuracy of ±2% at 20% to 100% relative humidity, at...

$5.95

IN STOCK

Adafruit Infineon Trust M Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 4351

This is a STEMMA I2C breakout for the Infineon OPTIGA TRUST M SLS 32AIA. OPTIGA Trust M is the next generation of Trust X. OPTIGA Trust M brings...

This is a STEMMA I2C breakout for the Infineon OPTIGA TRUST M SLS 32AIA. OPTIGA Trust M is the next generation of Trust X. OPTIGA Trust M brings RSA 1K/2K + ECC256/384. A crypto authentication chip much like the ATECC608 STEMMA we put into the shop last week, but with: ECC NIST P256/P384, SHA-256, TRNG, DRNG, RSA® 1024/2048 and 4.5K of user memory. This chip can store your private keys securely, as well as generate true random...

$4.95

55 IN STOCK

Adafruit Mini PiTFT 1.3" - 240x240 TFT Add-on for Raspberry Pi

PRODUCT ID: 4484

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the...

If you're looking for the most compact li'l color display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit Mini PiTFT - 1.3" 240x240 Color TFT Add-on for Raspberry Pi is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color 240x240 pixel IPS display with great visibility at all...

$14.95

IN STOCK

Adafruit Wii Nunchuck Breakout Adapter - Qwiic / STEMMA QT

PRODUCT ID: 4836

Dig out that old Wii controller and use it as a sleek controller for your next robot if you like. The Adafruit Adafruit Wii Nunchuck Breakout Adapter...

Dig out that old Wii controller and use it as a sleek controller for your next robot if you like. The Adafruit Adafruit Wii Nunchuck Breakout Adapter fits snugly into the Wii connector and performs the level shifting and power regulation needed to use the controller with any microcontroller or microcomputer. The Wii controllers use a standard I2C interface, and there's existing code for both Arduino and CircuitPython/Python for quick...

$2.95

IN STOCK

JST PH 4-pin Horizontal Connector (10-pack) - STEMMA

PRODUCT ID: 4392

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the horizontal style. You can use these with any of our JST PH 4 / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). However, you can fit Seeed Grove connectors into JST PH which is pretty handy. We also carry these connectors...

$3.50

72 IN STOCK

Adafruit CLUE - nRF52840 Express with Bluetooth LE

PRODUCT ID: 4500

Do you feel like you just don't have a CLUE? Well, we can help with that - get a CLUE here at Adafruit by picking up this sensor-packed...

Do you feel like you just don't have a CLUE? Well, we can help with that - get a CLUE here at Adafruit by picking up this sensor-packed development board. We wanted to build some projects that have a small screen and a lot of sensors. To make it compatible with existing projects, we made it the same shape and size as the BBC micro:bit and with the same edge-connector on the bottom with 5 big pads so it will fit into your existing robot kit...

$44.95

IN STOCK

JST SH 4-pin Vertical Connector (10-pack) - Qwiic Compatible

PRODUCT ID: 4328

If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST...

If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. These connectors can be used with Qwiic boards and cables to easily connect sensors and drivers from one...

$3.95

87 IN STOCK

SparkFun Qwiic Multiport

PRODUCT ID: 4861

Qwiic, or STEMMA QT , is a very efficient way to quickly prototype an idea, but a lot of Qwiic/Stemma QT driver boards only have one port, and...

Qwiic, or STEMMA QT , is a very efficient way to quickly prototype an idea, but a lot of Qwiic/Stemma QT driver boards only have one port, and devices have two ports but that's only good for chaining. This Multiport board allows boards that have only one Stemma QT/Qwiic port to be added to the I2C bus. Or, use this hub to add as many I2C devices to the bus as you need. Complete with mounting holes so the board can be added to any system....

$2.95

IN STOCK

Adafruit TMP117 ±0.1°C High Accuracy I2C Temperature Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4821

The TMP117 Precision Temperature Sensor is an I2C temperature sensor that will help you easily add temperature measurement and adjustment to your...

The TMP117 Precision Temperature Sensor is an I2C temperature sensor that will help you easily add temperature measurement and adjustment to your project. In addition to the obvious support for reading the temperature, the TMP117 can also monitor the temperature and alert you when corrective action needs to be taken. We use the TMP117 (not N or M) variant, which has 16-bit / 0.0078°C measurement resolution, wide operating range of -55 to...

$11.50

67 IN STOCK

Adafruit ICM-20649 Wide Range ±30g ±4000dps 6-DoF IMU - STEMMA QT / Qwiic

PRODUCT ID: 4464

Most accelerometers have a similar range of measurements that they can make: often around 2G - 16G. Similarly, most gyros can measure in the range of...

Most accelerometers have a similar range of measurements that they can make: often around 2G - 16G. Similarly, most gyros can measure in the range of 250 degree/s to 2000 degrees/s. That's enough for many situations, however, there are many situations where it's not quite enough. When measuring things like a golf swing, soccer ball kick or perhaps a fancy racing car, you need a bit more performance out of your motion sensor. The ICM20649...

$14.95

IN STOCK

Adafruit LPS22 Pressure Sensor - STEMMA QT / Qwiic - LPS22HB

PRODUCT ID: 4633

We live on a planet with an atmosphere, a big ocean of gaseous air that keeps everything alive - and that atmosphere is constantly bouncing off of...

We live on a planet with an atmosphere, a big ocean of gaseous air that keeps everything alive - and that atmosphere is constantly bouncing off of us, exerting air pressure on everything around us. But, how much air is in the atmosphere, bearing down on us? This absolute pressure sensor, ST LPS22HB (a.k.a LPS22 ) can quickly and easily measure this air pressure, useful when you want to know about the weather (are we in a low-pressure or...

$6.95

IN STOCK

Adafruit PyBadge Starter Kit

PRODUCT ID: 4623

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, it's the Adafruit PyBadge!...

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino? That's right, it's the Adafruit PyBadge! We wanted to see how much we could cram into a 3 3⁄8 × 2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. The PyBadge is a compact board, like we said, it's credit card sized. It's powered...

$39.95

72 IN STOCK

Adafruit MS8607 Pressure Humidity Temperature Sensor

Adafruit MS8607 Pressure Humidity Temperature PHT Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4716

Because of their many applications, Pressure, Temperature, and Humidity sensors (PHT sensors) are a common offering from semiconductor companies. The...

Because of their many applications, Pressure, Temperature, and Humidity sensors (PHT sensors) are a common offering from semiconductor companies. The MS8607 PHT sensor from TE Connectivity does an admirable job of measuring a wide range of all three environmental conditions. Each and every MS8607 sensor is calibrated at the factory and the calibration constants stored in the sensor itself. This sensor is a one-stop-shop for all your common...

$14.95

IN STOCK

SparkFun Qwiic / Stemma QT FeatherWing with three QT boards plugged into the top

SparkFun Qwiic / Stemma QT FeatherWing (Shield for Thing Plus)

PRODUCT ID: 4515

The SparkFun Qwiic FeatherWing (Shield for Thing Plus ) provides an easy-to-assemble way to add the STEMMA QT / Qwiic connect ecosystem to any...

The SparkFun Qwiic FeatherWing (Shield for Thing Plus ) provides an easy-to-assemble way to add the STEMMA QT / Qwiic connect ecosystem to any development board with Feather/Thing Plus Footprint. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Feather to four SparkFun Qwiic / Stemma QT connectors. The plug-n-play ecosystem allows for easy daisy chaining so, as long as your devices are on different addresses, you can connect as...

$4.95

IN STOCK

JST PH 3-pin Horizontal Connector (10-pack) - STEMMA

PRODUCT ID: 4391

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 3 pin. These are the horizontal style. You can use these with any of our JST PH 3 / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). We also carry these connectors in vertical style. For more information about JST PH connectors, visit the JST website

$3.50

1 IN STOCK

Top view of a Qwiic pHAT installed on a Pi 4 connected to a temperature-humidity sensor.

SparkFun Qwiic pHAT v2.0 for Raspberry Pi - STEMMA QT / Qwiic

PRODUCT ID: 5142

The SparkFun Qwiic pHAT V2.0 for Raspberry Pi provides you with the quickest and easiest way to enter into SparkFun’s Qwiic or STEMMA QT...

The SparkFun Qwiic pHAT V2.0 for Raspberry Pi provides you with the quickest and easiest way to enter into SparkFun’s Qwiic or STEMMA QT ecosystem while still using that Raspberry Pi that you’ve come to know and love. The Qwiic pHAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic/QT connectors on the HAT. Since this system allows for daisy-chaining boards with different addresses, you can plug...

$7.95

IN STOCK

Adafruit Metro ESP32-S2

PRODUCT ID: 4775

What's Metro shaped and has an ESP32-S2 WiFi module? What has a STEMMA QT connector for I2C devices, and a Lipoly charger circuit? What has your...

What's Metro shaped and has an ESP32-S2 WiFi module? What has a STEMMA QT connector for I2C devices, and a Lipoly charger circuit? What has your favorite Espressif WiFi microcontroller and lots of memory for your next IoT project? That's right - its the new Adafruit Metro ESP32-S2! With native USB and a load of PSRAM this board is perfect for use with CircuitPython or Arduino, to add low-cost WiFi while keeping shield-compatibility. The...

$19.95

70 IN STOCK

Adafruit LPS33HW Water Resistant Pressure Sensor wired to a Feather and OLED via QT cables

Adafruit LPS33HW Water Resistant Pressure Sensor - STEMMA QT

PRODUCT ID: 4414

Sometimes you need to sense pressure in a damp or caustic environment. And sometimes you need to know the relative changes in pressure as well as the...

Sometimes you need to sense pressure in a damp or caustic environment. And sometimes you need to know the relative changes in pressure as well as the absolute pressure. For the times you need to do both (or either), the LPS33HW is the pressure sensor for you. Combining protection from water intrusion with support for high precision relative and absolute measurements, this sensor will do what you need. With drivers for CircuitPython, Arduino, and...

$12.50

IN STOCK

Adafruit DS1841 I2C Digital 10K Potentiometer Breakout - STEMMA QT / Qwiic

PRODUCT ID: 4570

Potentiometers are the perfect tool when you want to change your circuit by turning a knob. Turns out, there are times when you want to adjust your...

Potentiometers are the perfect tool when you want to change your circuit by turning a knob. Turns out, there are times when you want to adjust your circuit without manually turning a knob, and the DS1841 I2C Logarithmic Resistor from Maxim can do just that. It's a programmable resistor, similar to an I2C potentiometer like the DS3502 I2C Potentiometer , so why another? The big difference between the two is how the...

$5.95

IN STOCK

Adafruit FunHouse - WiFi Home Automation Development Board

PRODUCT ID: 4985

Home is where the heart is...it's also where we keep all our electronic bits. So why not wire it up with sensors and actuators to turn our house...

Home is where the heart is...it's also where we keep all our electronic bits. So why not wire it up with sensors and actuators to turn our house into an electronic wonderland. Whether it's tracking the environmental temperature and humidity in your laundry room, or notifying you when someone is detected in the kitchen, to sensing when a window was left open, or logging when your cat leaves through the pet door, this board is designed to...

$34.95

IN STOCK

SparkFun STEMMA QT / Qwiic Mux Breakout - 8 Channel

PRODUCT ID: 4704

Do you have too many sensors with the same I2C address? Put them on the SparkFun Qwiic Mux Breakout to get them all talking on the same bus! The...

Do you have too many sensors with the same I2C address? Put them on the SparkFun Qwiic Mux Breakout to get them all talking on the same bus! The Qwiic Mux Breakout enables communication with multiple I2C devices that have the same address that makes it simple to interface with. The Qwiic Mux also has eight configurable addresses of its own, allowing for up to 64 I2C buses on a connection. To make it even easier to use this multiplexer, all...

$11.95

65 IN STOCK

JST PH 4-pin Plug to Color Coded Alligator Clips Cable

PRODUCT ID: 4029

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. Can also be used with any STEMMA breakouts! This cable has a JST PH 4-pin on one side and alligator clips on the other, so it could be used to connect to wires or pads...

$2.50

IN STOCK

Micro Servo with 3-pin JST Cable - STEMMA Connector Compatible

PRODUCT ID: 4326

This tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to...

This tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller . You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. Of course, it's not nearly as strong as a standard...

$5.95

IN STOCK

Grove Shield FeatherWing for Particle Mesh and all Feathers

PRODUCT ID: 4309

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for any Particle Mesh or Feather board, so that you can easily...

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for any Particle Mesh or Feather board, so that you can easily interface with Seeed's huge collection of Grove sensors. Now you can have full range of hundreds of Grove modules with Particle Mesh along with our Feather line! Working with Grove requires no soldering. Just plug the sensors, actuators, or displays into this shield via a Grove cable (not included),...

$5.95

IN STOCK

JST PH 4-pin Vertical Connector (10-pack) - STEMMA

PRODUCT ID: 4390

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the vertical style. You can use these with any of our JST PH 4 / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). However, you can fit Seeed Grove connectors into JST PH which is pretty handy. We also carry these connectors in right angle...

$3.50

27 IN STOCK

SparkFun Qwiic / STEMMA QT HAT for Raspberry Pi

PRODUCT ID: 4688

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter SparkFun’s Qwiic / STEMMA QT ecosystem when using...

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter SparkFun’s Qwiic / STEMMA QT ecosystem when using that Raspberry Pi that you’ve come to know and love. The Qwiic HAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic connectors on the HAT. Since the Qwiic system allows for daisy-chaining boards with different addresses, you can stack as many sensors as...

$7.50

85 IN STOCK

STEMMA Wired Tactile Push-Button Pack - 5 Color Pack

PRODUCT ID: 4431

Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button...

Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. Each button comes with a candy-colored round cap snapped on. You get one of each color-- blue,...

$7.50

IN STOCK

Circuit Playground TFT Gizmo - Bolt-on Display + Audio Amplifier

PRODUCT ID: 4367

Extend and expand your Circuit Playground projects with a bolt on TFT Gizmo that lets you add a lovely color display in a sturdy and reliable...

Extend and expand your Circuit Playground projects with a bolt on TFT Gizmo that lets you add a lovely color display in a sturdy and reliable fashion. This PCB looks just like a round TFT breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Once attached you'll get a 1.54" 240x240 IPS display with backlight control, two 3-pin STEMMA connectors for attaching NeoPixel strips or servos, and a...

$19.95

IN STOCK

Adafruit PyBadge LC - MakeCode Arcade, CircuitPython, or Arduino - Low Cost Version

PRODUCT ID: 3939

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino even when you're on a budget? That's right,...

What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino even when you're on a budget? That's right, it's the Adafruit PyBadge LC! We wanted to see how much we could cram into a 3 3⁄8 × 2 1⁄8 inch rounded rectangle, to make an all-in-one dev board with a lot of possibilities, and this is what we came up with. The PyBadge is a compact board, like we said, it's...

$24.95

IN STOCK

JST PH 3-pin Vertical Connector (10-pack) - STEMMA

PRODUCT ID: 4389

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 3 pin. These are the vertical style. You can use these with any of our JST PH 3 / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). We also carry these connectors in horizontal style. For more information about JST PH connectors, visit the JST...

$3.50

33 IN STOCK

I2CMini by Excamera Labs

PRODUCT ID: 4970

I²CMini is an easy-to-use, open-source tool for controlling I²C devices over USB, 100% compatible with I²CDriver. Its a small friend...

I²CMini is an easy-to-use, open-source tool for controlling I²C devices over USB, 100% compatible with I²CDriver. Its a small friend that will make working with I2C a breeze, especially if they have a Qwiic/Stemma QT or even Grove I2C connector! USB to I²C interface in a tiny 18x18mm board Can act as a I²C controller, passive monitor, and capture-to-PC supported at 400 kHz Two I²C ports: one on 0.1" header;...

$14.95

84 IN STOCK

Adafruit H3LIS331 Ultra High Range Triple-Axis Accelerometer - STEMMA QT / Qwiic

PRODUCT ID: 4627

It’s not hard to find an accelerometer that can measure accelerations up to 16g, but if you need an accelerometer that can measure even larger...

It’s not hard to find an accelerometer that can measure accelerations up to 16g, but if you need an accelerometer that can measure even larger amounts of acceleration, your options narrow (The ICM20649 is a great sensor and can measure up to ±30g). Enter the LIS331 family of accelerometers from ST, including the H3LIS331 and LIS331HH . As their model numbers may suggest, the LIS331s are close...

$24.95

IN STOCK

Circuit Playground 200x200 Tri-Color E-Ink Gizmo - E-Ink Display + Audio Amplifier

PRODUCT ID: 4869

Extend and expand your Circuit Playground projects with a bolt-on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and...

Extend and expand your Circuit Playground projects with a bolt-on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and reliable fashion. This PCB looks just like a round E-Ink breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Chances are you've seen one of those new-fangled 'e-readers' like the Kindle or Nook. They have gigantic electronic paper...

$21.95

35 IN STOCK

Adafruit TMP235 - Plug-and-Play STEMMA Analog Temperature Sensor - TMP235

PRODUCT ID: 4686

For fans of the TMP36, we now have a very similar analog temperature sensor with a 3-pin JST connector (we call these STEMMA connectors). Unlike many...

For fans of the TMP36, we now have a very similar analog temperature sensor with a 3-pin JST connector (we call these STEMMA connectors). Unlike many of our temperature sensors, this one is analog output, not I2C, so its best used by a microcontroller with an analog input, as most microcontrollers do. These sensors are very simple to use, no libraries or complex configurations required. Plug this board into any of our 3-pin JST PH cables (we...

$2.50

IN STOCK

Adafruit LPS25 Pressure Sensor wired up to a Feather with OLED via QT cable

Adafruit LPS25 Pressure Sensor - STEMMA QT / Qwiic - LPS25HB

PRODUCT ID: 4530

We live on a planet with an atmosphere, a big ocean of gaseous air that keeps everything alive - and that atmosphere is constantly bouncing off of...

We live on a planet with an atmosphere, a big ocean of gaseous air that keeps everything alive - and that atmosphere is constantly bouncing off of us, exerting air pressure on everything around us. But, how much air is in the atmosphere, bearing down on us? This absolute pressure sensor, ST LPS25HB can quickly and easily measure this air pressure, useful when you want to know about the weather (are we in a low pressure or high...

$9.95

67 IN STOCK

Adafruit NeoTrellis M4 Mainboard - featuring SAMD51

PRODUCT ID: 3938

We got a big ol' blender and tossed in an ItsyBitsy M4, two NeoTrellis boards and an electret mic amp - turned on the 'mix' button and...

We got a big ol' blender and tossed in an ItsyBitsy M4, two NeoTrellis boards and an electret mic amp - turned on the 'mix' button and out came the NeoTrellis M4 - a super fun dev board for anyone who likes to squish buttons, see pretty lights and maybe make a tune or two. The NeoTrellis M4 is an all-in-one USB + NeoPixel + Elastomer + Audio board. It's powered by our new favoritest-chip-in-the-world, the SAMD51, a Cortex M4 core...

$39.95

IN STOCK

Adafruit LIS331 Triple-Axis Wide-Range ±24g Accelerometer - STEMMA QT / Qwiic

PRODUCT ID: 4626

It’s not hard to find an accelerometer that can measure accelerations up to 16g, but if you need an accelerometer that can measure even larger...

It’s not hard to find an accelerometer that can measure accelerations up to 16g, but if you need an accelerometer that can measure even larger amounts of acceleration, your options narrow. Enter the LIS331 family of accelerometers from ST, including the LIS331HH . As the model number suggests, the LIS331s are close cousins to the venerable LIS3DH accelerometer that is on every Circuit Playground, from the Circuit Playground Classic to the...

$10.95

15 IN STOCK

Adafruit PyBadge Low Cost Starter Kit

PRODUCT ID: 4624

Get started with the Adafurit PyBadge LC in a jiffy with this all-in-one kit that has everything you need to make a portable, rechargeable...

Get started with the Adafurit PyBadge LC in a jiffy with this all-in-one kit that has everything you need to make a portable, rechargeable gaming/electronics/name-tag system. What's the size of a credit card and can run CircuitPython, MakeCode Arcade or Arduino even when you're on a budget? That's right, it's the Adafruit PyBadge LC! We wanted to see how much we could cram into a 3 3/8 × 2 1/8 inch rounded...

$32.50

72 IN STOCK

Binho Qwiic or Stemma QT Interface Board adapter

Binho Qwiic / Stemma QT Interface Board

PRODUCT ID: 4462

This board makes it easy for you to interface your Binho Nova host adapter with up to 4 strings of Qwiic / Stemma QT I2C devices. It also breaks...

This board makes it easy for you to interface your Binho Nova host adapter with up to 4 strings of Qwiic / Stemma QT I2C devices. It also breaks out all of the pins to a series of headers for convenient jumping to other circuits or perhaps your logic analyzer to monitor everything while you develop and debug. This is the easiest way to use the Binho Nova with our wide range of Stemma QT sensors and devices, with plug-n-play simplicity. This...

$7.95

8 IN STOCK

Adafruit LSM303AGR Accelerometer Magnetometer - STEMMA QT Qwiic

PRODUCT ID: 4413

Do you know which way the wind blows? You will now, with this triple-axis accelerometer/magnetometer compass module. Inside are two sensors, one is a...

Do you know which way the wind blows? You will now, with this triple-axis accelerometer/magnetometer compass module. Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a magnetometer that can sense where the strongest magnetic force is coming from, generally used to detect magnetic north. By combining this data you can then orient your...

NOTIFY ME

$8.95

OUT OF STOCK

NOTIFY ME

Adafruit 9-DOF Orientation IMU Fusion Breakout - BNO085 (BNO080) - STEMMA QT / Qwiic

PRODUCT ID: 4754

Here it is, the motion sensor you were looking for: the one that just gives you the directly usable information without requiring you to first...

Here it is, the motion sensor you were looking for: the one that just gives you the directly usable information without requiring you to first consult with a PhD to learn the arcane arts of Sensor Fusion . The BNO085 takes the life's work of multiple people who have spent their entire career focused on how to get useful information from direct motion sensor measurements and then squeezes that information down into a 5.2x3.8mm box, along with...

NOTIFY ME

$19.95

OUT OF STOCK

NOTIFY ME

Adafruit Triple-axis Magnetometer - LIS2MDL - STEMMA QT / Qwiic

PRODUCT ID: 4488

Sense the magnetic fields that surround us with this handy triple-axis magnetometer (compass) module. Magnetometers can sense where the strongest...

NOTIFY ME

$5.95

OUT OF STOCK

NOTIFY ME

Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055 - STEMMA QT / Qwiic

PRODUCT ID: 4646

If you've ever ordered and wire up a 9-DOF sensor, chances are you've also realized the challenge of turning the sensor data from an...

If you've ever ordered and wire up a 9-DOF sensor, chances are you've also realized the challenge of turning the sensor data from an accelerometer, gyroscope, and magnetometer into actual "3D space orientation"! Orientation is a hard problem to solve. The sensor fusion algorithms (the secret sauce that blends accelerometer, magnetometer, and gyroscope data into stable three-axis orientation output) can...

NOTIFY ME

$19.95

OUT OF STOCK

NOTIFY ME

Adafruit IS31FL3741 13x9 PWM RGB LED Matrix Driver - STEMMA QT / Qwiic

PRODUCT ID: 5201

Add a splash of RGB LEDs to a project you're working on, with this adorable 13x9 RGB LED matrix breakout. It features -- no surprise -- 117 RGB...

Add a splash of RGB LEDs to a project you're working on, with this adorable 13x9 RGB LED matrix breakout. It features -- no surprise -- 117 RGB LEDs, each one 2x2mm in size, in a 13x9 grid with 3mm pitch spacing. Unlike our 8x8 dotstar grid here, these are not NeoPixel or DotStar or other 'smart' RGB LEDs. Instead of having a lil chip in each LED, there's one large controller chip that handles all the PWM for you. The ISSI...

NOTIFY ME

$14.95

OUT OF STOCK

NOTIFY ME

Adafruit ISM330DHCX + LIS3MDL FeatherWing - High Precision 9-DoF IMU

PRODUCT ID: 4569

Upgrade any Feather board with precision motion sensing with the ST 9-DoF IMU, an all-in-one sensing 'Wing. It sports two fantastic sensors...

Upgrade any Feather board with precision motion sensing with the ST 9-DoF IMU, an all-in-one sensing 'Wing. It sports two fantastic sensors from ST to provide 9 degrees of full-motion data. The ST ISM330DHCX is an industrial quality Accelerometer+Gyroscope 6-DOF IMUs (inertial measurement unit). This IMU sensor has 6 degrees of freedom - 3 degrees each of linear acceleration and angular velocity at varying rates...

NOTIFY ME

$17.50

OUT OF STOCK

NOTIFY ME

Adafruit LED Glasses Front Panel - 116 RGB LEDs with I2C Driver - STEMMA QT / Qwiic

PRODUCT ID: 5210

Have you always wanted to upgrade your ensemble with a creepy-cool creature PCB silkscreen and an eye-blistering arrangement of LEDs? We love to put...

Have you always wanted to upgrade your ensemble with a creepy-cool creature PCB silkscreen and an eye-blistering arrangement of LEDs? We love to put NeoPixels on our face, as evidenced by our many glowy LED glasses projects. Each of these requires quite a bit of soldering, and the cost of each NeoPixel adds up quickly. So we wanted to make a PCB assembly that can be used by any microcontroller to make glamorous face-tronics. Please note : You...

NOTIFY ME

$19.95

OUT OF STOCK

NOTIFY ME

Adafruit ATECC608 Breakout Board next to clear padlock

Adafruit ATECC608 Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 4314

You've got secrets, and you want to keep them safe? Most microcontrollers are not designed to protect against snoopers, but a...

You've got secrets, and you want to keep them safe? Most microcontrollers are not designed to protect against snoopers, but a crypto-authentication chip can be used to lock away private keys securely. Once the private key is saved inside, it can't be read out, all you can do is send it challenge-response queries. That means that even if someone gets hold of your hardware and can read back the firmware, they won't be able to extract...

NOTIFY ME

$4.95

OUT OF STOCK

NOTIFY ME

Adafruit BMP390L Precision Barometric Pressure and Altimeter

Adafruit BMP390 - Precision Barometric Pressure and Altimeter - STEMMA QT / Qwiic

PRODUCT ID: 4816

Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, BMP280, BMP388... now we've got the next generation, the...

Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, BMP280, BMP388... now we've got the next generation, the Adafruit BMP390 (we refer to it as the BMP390L or BMP390, same thing!) Precision Barometric Pressure and Altimeter Breakout . As you would expect, this sensor is similar to its earlier versions but even better . The BMP390 has better precision than ever, which makes it excellent for environmental sensing...

NOTIFY ME

$10.95

OUT OF STOCK

NOTIFY ME

Adafruit LSM6DSOX 6 DoF Accelerometer and Gyroscope - STEMMA QT / Qwiic

PRODUCT ID: 4438

Behold, the ST LSM6DSOX: The latest in a long line of quality Accelerometer+Gyroscope 6-DOF IMUs from ST. This IMU sensor has 6 degrees of freedom -...

Behold, the ST LSM6DSOX: The latest in a long line of quality Accelerometer+Gyroscope 6-DOF IMUs from ST. This IMU sensor has 6 degrees of freedom - 3 degrees each of linear acceleration and angular velocity at varying rates within a respectable range. For the accelerometer: ±2/±4/±8/±16 g at 1.6 Hz to 6.7KHz update rate. For the gyroscope: ±125/±250/±500/±1000/±2000 dps at 12.5 Hz...

NOTIFY ME

$11.95

OUT OF STOCK

NOTIFY ME

Adafruit LSM6DS33 6-DoF Accel + Gyro IMU - STEMMA QT / Qwiic

PRODUCT ID: 4480

Add motion and orientation sensing to your Arduino project with this affordable 6 Degree of Freedom (6-DoF) sensor with sensors from ST. The...

Add motion and orientation sensing to your Arduino project with this affordable 6 Degree of Freedom (6-DoF) sensor with sensors from ST. The board includes an LSM6DS33 , a 6-DoF IMU accelerometer + gyro. The 3-axis accelerometer, can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space. The 3-axis gyroscope that can measure spin and twist. This chip isn't the newest...

NOTIFY ME

$9.95

OUT OF STOCK

NOTIFY ME

Adafruit HalloWing M4 Express - ORANGE HALLOWEEN EDITION!

PRODUCT ID: 4300

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we...

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we UPPED our -skull-shaped development board game, and re-spinned (re-spun?) the HalloWing M0 into the HalloWing M4 with MORE of everything that makes this the spoooookiest dev board. New! For October 2019, we're got limited edition halloween-orange HallowingM4's - Same exact electronics and...

NOTIFY ME

$39.95

OUT OF STOCK

NOTIFY ME

Adafruit LSM6DSOX + LIS3MDL - Precision 9 DoF IMU - STEMMA QT / Qwiic

PRODUCT ID: 4517

Add high-quality motion, direction, and orientation sensing to your Arduino project with this all-in-one 9 Degree of Freedom (9-DoF) sensor...

Add high-quality motion, direction, and orientation sensing to your Arduino project with this all-in-one 9 Degree of Freedom (9-DoF) sensor with sensors from ST. This little breakout contains two chips that sit side-by-side to provide 9 degrees of full-motion data. The board includes an LSM6DSOX , a 6-DoF IMU accelerometer + gyro. The 3-axis accelerometer can tell you which direction is down towards the Earth (by measuring gravity) or...

NOTIFY ME

$14.95

OUT OF STOCK

NOTIFY ME

Adafruit MSA301 Triple Axis Accelerometer - STEMMA QT / Qwiic

PRODUCT ID: 4344

The MSA301 is a super small and low-cost triple-axis accelerometer . It's inexpensive, but has just about every 'extra' you'd want in...

The MSA301 is a super small and low-cost triple-axis accelerometer . It's inexpensive, but has just about every 'extra' you'd want in an accelerometer: Three-axis sensing, 14-bit resolution±2g/±4g/±8g/±16g selectable scalingI2C interface on fixed I2C address 0x26Interrupt outputMultiple data rate options 1 Hz to 500 HzAs low as 2uA current draw in low power mode (just the chip itself, not including any...

NOTIFY ME

$4.50

OUT OF STOCK

NOTIFY ME

Adafruit LSM6DS33 + LIS3MDL - 9 DoF IMU with Accel / Gyro / Mag - STEMMA QT Qwiic

PRODUCT ID: 4485

Add motion, direction and orientation sensing to your Arduino project with this all-in-one 9 Degree of Freedom (9-DoF) sensor with sensors...

Add motion, direction and orientation sensing to your Arduino project with this all-in-one 9 Degree of Freedom (9-DoF) sensor with sensors from ST. This little breakout contains two chips that sit side-by-side to provide 9 degrees of full motion data. The board includes an LSM6DS33 , a 6-DoF IMU accelerometer + gyro. The 3-axis accelerometer, can tell you which direction is down towards the Earth (by measuring gravity) or how fast the...

NOTIFY ME

$14.95

OUT OF STOCK

NOTIFY ME

Angled shot of Adafruit SCD-41 - NDIR CO2 Temperature and Humidity Sensor.

Adafruit SCD-41 - True CO2 Temperature and Humidity Sensor - STEMMA QT / Qwiic

PRODUCT ID: 5190

Take a deep breath in...now slowly breathe out. Mmm isn't it wonderful? All that air around us, which we bring into our lungs, extracts oxygen...

NOTIFY ME

$59.50

OUT OF STOCK

NOTIFY ME

Adafruit Sensirion SHT40 Temperature & Humidity Sensor wired to Feather with QT cable, showing temperature and humidity on OLED.

Adafruit Sensirion SHT40 Temperature & Humidity Sensor - STEMMA QT / Qwiic

PRODUCT ID: 4885

Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And finally, we have some that have a...

Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And finally, we have some that have a true I2C interface for easy reading. The SHT40 sensor is the fourth generation (started at the SHT10 and worked its way up to the top!). The SHT40 has an excellent ±1.8% typical relative humidity accuracy from 25 to 75% and ±0.2 °C typical accuracy from 0 to 75 °C. Unlike...

NOTIFY ME

$5.95

OUT OF STOCK

NOTIFY ME

Adafruit LC709203F LiPoly / LiIon Fuel Gauge and Battery Monitor - STEMMA JST PH & QT / Qwiic

PRODUCT ID: 4712

Low cost Lithium Polymer batteries have revolutionized electronics - they're thin, they're light, they can be regulated down to 3.3V and...

Low cost Lithium Polymer batteries have revolutionized electronics - they're thin, they're light, they can be regulated down to 3.3V and they're easy to charge. On your phone, there's a little image of a battery cell that tells you the percentage of charge - so you know when you absolutely need to plug it in and when you can stay untethered. The Adafruit LC709203F LiPoly / LiIon Fuel Gauge and Battery Monitor does the same thing....

NOTIFY ME

$5.95

OUT OF STOCK

NOTIFY ME

Angled shot of Adafruit SCD-40 - NDIR CO2 Temperature and Humidity Sensor.

Adafruit SCD-40 - True CO2, Temperature and Humidity Sensor - STEMMA QT / Qwiic

PRODUCT ID: 5187

Take a deep breath in...now slowly breathe out. Mmm isn't it wonderful? All that air around us, which we bring into our lungs, extracts oxygen...

NOTIFY ME

$49.50

OUT OF STOCK

NOTIFY ME

Adafruit LSM6DSOX + LIS3MDL FeatherWing - Precision 9-DoF IMU

PRODUCT ID: 4565

Upgrade any Feather board with precision motion sensing with the ST 9-DoF IMU, an all-in-one sensing 'Wing. It sports two fantastic sensors from...

Upgrade any Feather board with precision motion sensing with the ST 9-DoF IMU, an all-in-one sensing 'Wing. It sports two fantastic sensors from ST to provide 9 degrees of full-motion data. The board includes an LSM6DSOX , a 6-DoF IMU accelerometer + gyro. The 3-axis accelerometer can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space. The 3-axis gyroscope can measure...

NOTIFY ME

$14.95

OUT OF STOCK

NOTIFY ME

Adafruit MLX90640 24x32 IR Thermal Camera Breakout - 110 Degree FoV

PRODUCT ID: 4469

You can now add affordable heat-vision to your project and with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of...

NOTIFY ME

$64.95

OUT OF STOCK

NOTIFY ME

Adafruit LSM6DSO32 6-DoF Accelerometer and Gyroscope - STEMMA QT / Qwiic

PRODUCT ID: 4692

Behold, the ST LSM6DSO32: The latest in a long line of quality Accelerometer+Gyroscope 6-DOF IMUs from ST. This IMU is like a big sister to the...

Behold, the ST LSM6DSO32: The latest in a long line of quality Accelerometer+Gyroscope 6-DOF IMUs from ST. This IMU is like a big sister to the LSM6DSOX; it has the same pinout and firmware - but the accelerometer component can go up to 32g instead of the normal 16g maximum. This IMU sensor has 6 degrees of freedom - 3 degrees each of linear acceleration and angular velocity at varying rates within a respectable range. For the...

NOTIFY ME

$11.95

OUT OF STOCK

NOTIFY ME

Adafruit MONSTER M4SK - DIY Electronic Eyes Mask

PRODUCT ID: 4343

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER...

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER M4SK is like the Hallowing but twice as good, with two gorgeous 240x240 pixel IPS TFT displays, driven by a 120MHZ Cortex M4 processor that can pump out those pixels super fast. You'll get the same quality display as our Raspberry Pi Eyes kit but without needing to tote around a full Linux...

NOTIFY ME

$44.95

OUT OF STOCK

NOTIFY ME

STEMMA Wired Potentiometer Breakout Board - 10K ohm Linear

PRODUCT ID: 4493

For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm...

For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching JST PH 3-Pin to Male Header Cables - 200mm, so wiring up is a cinch. Simply plug the cable in, then use the black wire to connect to your ground, white wire to the input/signal pin and the red wire to your power pin. The power pin voltage should match the voltage max of your...

NOTIFY ME

$3.95

OUT OF STOCK

NOTIFY ME

Adafruit HTS221 - Temperature & Humidity Sensor Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 4535

Humidity is the concentration of water vapor (water when it's a gas) in the air. Some places have more and make you feel soggy and hot like...

Humidity is the concentration of water vapor (water when it's a gas) in the air. Some places have more and make you feel soggy and hot like you're in a sauna. Other places don't have much, which makes it easier to get nose bleeds and static zaps. These are just a few examples of how humidity can have a noticeable impact on things that grow, like mushrooms or humans, as well as things that are sensitive to moisture, like delicate...

NOTIFY ME

$9.95

OUT OF STOCK

NOTIFY ME

Adafruit EdgeBadge - TensorFlow Lite for Microcontrollers

PRODUCT ID: 4400

Machine learning has come to the 'edge' - small microcontrollers that can run a very miniature version of TensorFlow Lite to do ML...

Machine learning has come to the 'edge' - small microcontrollers that can run a very miniature version of TensorFlow Lite to do ML computations. But you don't need super complex hardware to start developing your own TensorFlow models! We've adapted our popular PyBadge board to add a microphone so you can dip your toes into machine learning waters. It does everything that the PyBadge does, and as we make more projects that...

NOTIFY ME

$35.95

OUT OF STOCK

NOTIFY ME

Adafruit ISM330DHCX - 6 DoF IMU - Accelerometer and Gyroscope - STEMMA QT / Qwiic

PRODUCT ID: 4502

Behold, the ST ISM330DHCX: an industrial quality Accelerometer+Gyroscope 6-DOF IMUs (inertial measurement unit) from ST. This IMU sensor has 6...

Behold, the ST ISM330DHCX: an industrial quality Accelerometer+Gyroscope 6-DOF IMUs (inertial measurement unit) from ST. This IMU sensor has 6 degrees of freedom - 3 degrees each of linear acceleration and angular velocity at varying rates within a respectable range. For the accelerometer: ±2/±4/±8/±16 g at 1.6 Hz to 6.7KHz update rate. For the gyroscope:...

NOTIFY ME

$14.95

OUT OF STOCK

NOTIFY ME

JST-SH 4-pin STEMMA QT / Qwiic Cables in Various Lengths

PRODUCT ID: 4912

These cables can be used with Qwiic or STEMMA QT boards to easily connect sensors and drivers from one board to the other. This variety of...

These cables can be used with Qwiic or STEMMA QT boards to easily connect sensors and drivers from one board to the other. This variety of cables gives you the option of breadboarding with headers, using capacitive touch with alligator clips, and more. Compared with the chunkier JST-PH, these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. When used with Qwiic the colors are: ...

MORE INFO

IN STOCK

MORE INFO

Black Lives Matter Education & Workshop Kit

PRODUCT ID: 4703

The Black Lives Matter Education & Workshop Kit is an open-source design the Adafruit team published during the peaceful demonstrations for...

The Black Lives Matter Education & Workshop Kit is an open-source design the Adafruit team published during the peaceful demonstrations for social justice in the summer of 2020 (https://github.com/adafruit/BLM-Badge-PCB). As a company and culture we came together to make our voices heard, share the pain we all had, the anger, and then work together for equality and justice in our...

MORE INFO

Angled shot of green Metro dev board hooked up to an OLED displaying Bitcoin data.

Adafruit Metro M7 with AirLift - Featuring NXP iMX RT1011

PRODUCT ID: 4950

Coming soon! Sign up to be notified when these are in stock! Get ready for our fastest Metro ever - the NXP iMX RT1011 microcontroller powers this...

Coming soon! Sign up to be notified when these are in stock! Get ready for our fastest Metro ever - the NXP iMX RT1011 microcontroller powers this board with a 500 MHz ARM Cortex M7 processor. There's 4 MB of execute-in-place QSPI for firmware + disk storage and 128KB of SRAM in-chip We're still working on the design but here's some stuff you can look forward to: Features: NXP iMX RT1011 processor - ARM Cortex M7 processor running...

MORE INFO

COMING SOON

MORE INFO

Adafruit 9-DOF LSM9DS1 Breakout Board - STEMMA QT / Qwiic

PRODUCT ID: 4634

Add motion, direction, and orientation sensing to your project with this all-in-one 9-DOF sensor that is STEMMA QT ready for easy plug-n-play usage....

Add motion, direction, and orientation sensing to your project with this all-in-one 9-DOF sensor that is STEMMA QT ready for easy plug-n-play usage. Inside the chip are three sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space. The other is a 3-axis magnetometer that can sense where the strongest magnetic force is...

NOTIFY ME

$12.50

OUT OF STOCK

NOTIFY ME

Grove Shield FeatherWing - Wio Lite

PRODUCT ID: 4357

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for many Particle Mesh or Feather board, so that you can easily...

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for many Particle Mesh or Feather board, so that you can easily interface with Seeed's huge collection of Grove sensors. Now you can have full range of hundreds of Grove modules with Particle Mesh along with our Feather line! Working with Grove requires no soldering. Just plug the sensors, actuators, or displays into this shield via a Grove cable (not included),...

MORE INFO

DISCONTINUED

MORE INFO

Circuit Playground 152x152 Tri-Color E-Ink Gizmo - E-Ink Display + Audio Amplifier

PRODUCT ID: 4428

Discontinued - you can grab Circuit Playground 200x200 Tri-Color E-Ink Gizmo instead! Extend and expand your Circuit Playground projects...

Discontinued - you can grab Circuit Playground 200x200 Tri-Color E-Ink Gizmo instead! Extend and expand your Circuit Playground projects with a bolt on E-Ink Gizmo that lets you add a lovely tri-color e-Ink display in a sturdy and reliable fashion. This PCB looks just like a round E-Ink breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Chances are you've seen one of those...

MORE INFO

DISCONTINUED

MORE INFO

TSL2561 Digital Lux / Light Sensor on round STEMMA breakout

Adafruit STEMMA - TSL2561 Digital Lux / Light Sensor

PRODUCT ID: 3611

New from Adafruit, we are taking our most popular sensors and making them easier than ever to use! This is the Adafruit STEMMA TSL2561 which takes...

New from Adafruit, we are taking our most popular sensors and making them easier than ever to use! This is the Adafruit STEMMA TSL2561 which takes our favorite lux sensor and gives you two ways to play: you can use alligator clips to connect the sensor to your Flora, Gemma or Circuit Playground, or plug-n-play with STEMMA cables or Seeed Grove cables Each STEMMA board has level-shifting and protection circuitry on the power supply and data lines...

MORE INFO

DISCONTINUED

MORE INFO