Components & Parts
Adafruit's extensive selection of electronic components and parts will help you get your next project moving, printing, counting, or glowing. From SD cards and terminal blocks to modular snap boxes and capacitor books to keep your project organized, our Components and Parts section is the best place to start for all your electronics needs.
PRODUCT ID: 3122
Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Block Breakout . You get a nice solid PCB with an...
Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Block Breakout . You get a nice solid PCB with an DE-9 socket and two strips of terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. Perfect for when you need a non-standard wiring setup or interfacing to an older device with one of these connectors Sometimes DE-9 connectors are referred to as...
PRODUCT ID: 366
XBees are so cute and tiny but if you're using them in a circuit you'll be annoyed to find that your classic 0.1" headers don't fit...
XBees are so cute and tiny but if you're using them in a circuit you'll be annoyed to find that your classic 0.1" headers don't fit them! That's because they use 2mm spacing instead of 2.54mm spacing. That's why you need special sockets like these ones! As of Tuesday, June 16th, 2015 we are selling two sockets together instead of just one! These sockets have 10 pins, spaced 2mm apart. Check the...
PRODUCT ID: 1769
A simple 2-pin connector that is compatible with the "JST PH 2-pin" connector - perfect for soldering to the bottom of our 3.3V Logic...
A simple 2-pin connector that is compatible with the "JST PH 2-pin" connector - perfect for soldering to the bottom of our 3.3V Logic Trinket and 5V Logic Trinket! These mate perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector. Note : This product might be black or tan. We cannot control the color...
PRODUCT ID: 2830
These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do?...
These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do? They stack. Put the headers through your Feather and then you can not only plug them into a solderless breadboard, but you could attach circuitry on top as well Note : Comes with one 12-pin and one 16-pin header, Feathers not included
PRODUCT ID: 3123
Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Plug to Terminal Block Breakout . You get a nice solid PCB with an...
Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Plug to Terminal Block Breakout . You get a nice solid PCB with an DE-9 socket and two strips of terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. Perfect for when you need a non-standard wiring setup or interfacing to an older device with one of these connectors Sometimes DE-9 connectors are...
PRODUCT ID: 2886
These two Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!...
These two Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! What do they do? They get soldered on either side of the Feather board. Now you can plug in FeatherWings to add more capability to your portable project. Unlike our Feather Stacking Headers, they aren't designed to 'stack', but they're more compact. Note: Comes with one 12-pin and...
PRODUCT ID: 2940
These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're...
These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Feather project takes up, but still maintain that flexible configuration. "Normal" socket headers have an 8.5mm body height so this...
PRODUCT ID: 3084
Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high...
Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface of the chip of any dust or grease then peel...
PRODUCT ID: 373
This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more...
This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards. They will work where "thick pin" types go also, just need a little more solder to fill up the larger pads.
PRODUCT ID: 356
These are our favorite trim pots, perfect for breadboarding and prototyping. They have a long grippy adjustment knob and with 0.1" spacing, they...
These are our favorite trim pots, perfect for breadboarding and prototyping. They have a long grippy adjustment knob and with 0.1" spacing, they plug into breadboards or perfboards with ease. This is the same pot that comes with our character LCDs and tutorial packs.
PRODUCT ID: 3786
These are the easiest way possible to connect two wires - no if's, and's, or butt's! Well, actually, these are often referred to as wire...
These are the easiest way possible to connect two wires - no if's, and's, or butt's! Well, actually, these are often referred to as wire butts 'cause you 'butt' two wires together (hey we didn't come up with the name!) Butt seriously folks! OK, so despite the humor, these are really handy. If you want to quickly prototype some wiring, skip the soldering and use these 2-pin Wire Joints ! These connectors are...
PRODUCT ID: 3082
Looking for the best heat sink for your Raspberry Pi? Check out this nice and tall 15x15x15mm Heat Sink! This heat sink is made from high quality...
Looking for the best heat sink for your Raspberry Pi? Check out this nice and tall 15x15x15mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 or 4 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface of the chip of any dust or grease then peel off the...
PRODUCT ID: 805
These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless...
These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped by accident. Work great as on/off switches or selector switches, the middle pin is connected to either the left or right pin depending on which way the slider is pushed.
PRODUCT ID: 419
Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin,...
Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin, flexible membrane material with an adhesive backing (just remove the paper) so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 7 microcontroller pins (3-columns and 4-rows) to scan through the pad. Check the tutorials tab for links to an Arduino library...
PRODUCT ID: 1054
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them"...
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them" and then you see these little laser diode modules: what great timing! These encapsulated laser diodes are Class IIIa 5mW, with a 650nm red wavelength. They can be driven from 2.8V to 5.2V so they're great for your embedded electronics project. You can use these for laser harps, electronic...
PRODUCT ID: 1674
Drown out the voices in your head with a bone conduction transducer! This incredible speaker does not have a moving cone like most speakers...
Drown out the voices in your head with a bone conduction transducer! This incredible speaker does not have a moving cone like most speakers you've seen, instead, a small metal rod is wrapped with the voice coil. When current is pulsed through the coil, the magnetic field causes a piece of metal to expand and contract - if pressed against a flat surface or cavity it turns it into a speaker! Often these size transducers are pressed up against...
PRODUCT ID: 4079
Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins . You can plug this into your Raspberry Pi GPIO...
Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins . You can plug this into your Raspberry Pi GPIO port and then plug a HAT or Bonnet or Phat on top. Especially useful for Bonnets that have slim headers on the bottom, but you want them to clear some of the components on the Pi, or fit into a case nicer. The header body is a standard 8.5mm. The pins are 6mm tall, so they're securely plug...
PRODUCT ID: 1314
Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 4 ohm impedance and 3W or less of power....
Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 4 ohm impedance and 3W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our class D amplifier board. Speaker - 3" Diameter - 4 Ohm 3 Watt (0:01)
PRODUCT ID: 1119
Medium-sized clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a...
Medium-sized clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 10, they're pretty handy so you'll want to keep them around. You can find an EAGLE cad package for these in...
PRODUCT ID: 1661
uFL connectors are very small surface-mount parts used when an external RF antena is desired but a big bulky SMA connector takes up too much space....
uFL connectors are very small surface-mount parts used when an external RF antena is desired but a big bulky SMA connector takes up too much space. We use this part on our GPS and WiFi boards, they're great! Chances are your antenna doesn't use uFL as the main connector, in which case you should check out our uFL to SMA and uFL to RP-SMA adapter cables. These are also panel-mountable for a nice look. These are surface-mount but...
PRODUCT ID: 562
This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 10K ohm potentiometer, with a...
This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-points, so you can plug it into a breadboard or perfboard. Once you're done prototyping, you can drill a hole into your project box and mount...
PRODUCT ID: 4247
What do you do when you want to tinker with GPU hardware, but you don't have a display on hand? This HDMI Dummy Plug is a small...
What do you do when you want to tinker with GPU hardware, but you don't have a display on hand? This HDMI Dummy Plug is a small device that acts as a display emulator. Once it's plugged into the video output socket on your device or computer, the plug punks the operating system into detecting a connected display, and voilà! Now you have unimpeded access to your graphics card hardware. The plug only contains the...
PRODUCT ID: 1669
Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less...
Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. The pair have a handy SPK input cable to add audio to your displays (the connectors are similar to the JST-PH series which is ~2.0mm spacing). We're specifically carrying...
PRODUCT ID: 1699
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and...
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 0.1" spacing so it plugs very solidly into a breadboard, perma-proto or perf-board. Each order comes with one headphone jack, breadboard and audio cable not included!...
PRODUCT ID: 2658
Swapping around your SIM card into different devices? This trio of SIM adapters helps so that you can use one SIM card for various size-needs....
Swapping around your SIM card into different devices? This trio of SIM adapters helps so that you can use one SIM card for various size-needs. Two adapters fit Nano-SIMs (~12mm x ~9mm x ~0.7mm) and one fits Micro-SIMs (~15mm x ~12mm x ~0.8mm). In our two examples we broke down our GSM 2G SIM Card from Ting & Adafruit to it's smallest Nano self. Once in the adapters, they will fit 'plain...
PRODUCT ID: 4489
Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP...
Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP package so it's easy to fit onto any breadboard or perfboard. Each chip contains one full H-bridges (two half H-bridges). That means you can drive 2 solenoids or a single DC motors bi-directionally. Just make sure they're good for under 800 mA since that's the limit of this chip. They do...
PRODUCT ID: 1787
Level shifting chips let you connect 3V and 5V devices together safely. This chip is similar to others in the shop (such as the 74LVC125) except this...
Level shifting chips let you connect 3V and 5V devices together safely. This chip is similar to others in the shop (such as the 74LVC125) except this one is particularly good at converting 3V logic up to 5V . This is in demand especially when connecting some 3V devices such as the Teensy 3 to NeoPixels! Just power the 74AHCT125 with 5V, it will detect 3V logic properly. You can also use it to connect 5V logic out to 3V logic in, that's when...
PRODUCT ID: 355
When you need to switch a lot of power, N channel MOSFETs are best for the job. These FETs can switch over 60A and 30V and are TO-220 package so they...
When you need to switch a lot of power, N channel MOSFETs are best for the job. These FETs can switch over 60A and 30V and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220's, but because of the very low Rds(on) of down to 0.009 ohms (depending on the Vgs - check the datasheet) you can get away with no heatsinking for pretty high loads! The threshhold voltage is also very low, less than 2.5V...
PRODUCT ID: 1057
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them" and then you see...
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them" and then you see these little laser diode modules: what great timing! These encapsulated laser diodes are Class IIIa 5mW, with a 650nm red wavelength. They can be driven from 2.8V to 5.2V so they're great for your embedded electronics project. This particular laser diode has a lens attached to turn the dot into a line....
PRODUCT ID: 2822
If we could eat headers, we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and...
If we could eat headers, we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip male header is a great way to add pins to 2x20 0.1" holes in a PCB. They're also perfect companion piece to our 2x20-pin right-angle female header.
PRODUCT ID: 3870
Push once to turn on, push again to turn off, push again to turn the other side on, one last push and it's off again! It's basically a...
Push once to turn on, push again to turn off, push again to turn the other side on, one last push and it's off again! It's basically a push-button toggle switch that connects and disconnects. This clicky Mini On/Off Button switch makes a great power switch or mode toggler. They're often referred to as 'flashlight' switches because you see them used in small flashlights. Can reliably handle up to 500mA and up to 12VDC. This is...
PRODUCT ID: 2914
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these...
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") 4-Pole (TRRS) Audio Plug Terminal Block . TRRS stands for Tip, Ring, Ring, Sleeve. It has four total conductors - three...
PRODUCT ID: 377
This rotary encoder is the best of the best, its a high quality 24-pulse encoder, with detents and a nice feel. It is panel mountable for placement...
This rotary encoder is the best of the best, its a high quality 24-pulse encoder, with detents and a nice feel. It is panel mountable for placement in a box, or you can plug it into a breadboard (just cut/bend the two mechanical side tabs.) We also include a nice soft-touch knob with an arrow in it, fits perfectly and looks great. This encoder also has a push-button built into it so you can press onto the knob to close a separate switch. One...
PRODUCT ID: 1890
Listen up! This tiny 1" diameter speaker cone is the perfect addition to any small audio project where you need an 8 Ω impedance and will...
Listen up! This tiny 1" diameter speaker cone is the perfect addition to any small audio project where you need an 8 Ω impedance and will be using 0.5W or less of power. We particularly like this cone as it's very simple and its metal body is extremely lightweight. It's very similar to the speaker in the Drawdio kit. Works great with our Wave shield or class D amplifier board. Just be careful not to overdrive it if you're...
PRODUCT ID: 4048
We've carrying a new 1.27mm pitch 2x5 Mini SWD 0.05" Pitch Connector . It's a tinier, bite-sized version of the Box...
We've carrying a new 1.27mm pitch 2x5 Mini SWD 0.05" Pitch Connector . It's a tinier, bite-sized version of the Box Header used on our SWD Cable Breakout Board. Instead of a full shroud, there's a half-shroud with a key-notch. It'll takes a lot less space on your board! The header alone is great if you want to incorporate this piece of hardware with your own software. We're specifically selling it so...
PRODUCT ID: 482
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and...
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a green plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the...
PRODUCT ID: 1611
So squishy! These silicone elastomer keypads are just waiting for your fingers to press them. Go ahead, squish all you like! (They're durable and...
So squishy! These silicone elastomer keypads are just waiting for your fingers to press them. Go ahead, squish all you like! (They're durable and easy to clean, just wipe with mild soap and water) These are just like the light up rubber buttons you find on stuff like appliances and tools, but these are open source and easy to integrate into your next project. Each button is 10mm x 10mm square and 10mm tall. There is 5mm of grid spacing...
PRODUCT ID: 3101
Put your project in stealth mode with these silent Soft Tactile Switch Buttons . T actile switches are standard input "buttons" on...
Put your project in stealth mode with these silent Soft Tactile Switch Buttons . T actile switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 10, they're pretty handy so you'll want to keep them...
PRODUCT ID: 3923
Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power....
Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires with a connector on the end. It has a handy "Molex PicoBlade" 1.25mm pitch 2-pin cable, which makes plugging into a board easy. Or you can cut off the connector and just solder/clamp onto...
PRODUCT ID: 1660
Add tons of storage to your next project with this micro SD card socket. We use this part in all our designs and it works great with any microSD...
Add tons of storage to your next project with this micro SD card socket. We use this part in all our designs and it works great with any microSD ('transflash') of any storage size. It's a surface-mount part and the pins are underneath so it needs a fine tip and paste or thin solder to get in there and solder, not for beginners! It is a push-push type: push the card in to insert, push again to spring it out. You can get the EAGLE...
PRODUCT ID: 160
Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, connect...
Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, connect one pin to ground (either one) and the other pin to a square wave out from a timer or microcontroller. For the loudest tones, stay around 4 KHz, but works quite well from 2KHz to 10KHz. For extra loudness, you can connect both pins to a microcontroller and swap which pin is high or low...
PRODUCT ID: 1799
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with....
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 3.5mm TRRS Plug with four poles. TRRS stands for Tip, Ring, Ring, Sleeve. It has four total conductors -...
PRODUCT ID: 3351
Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less...
Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm spacing). This...
PRODUCT ID: 423
Your friends probably tell you that you are "good with your hands," but now you can also be good with your feet! This foot switch is made...
Your friends probably tell you that you are "good with your hands," but now you can also be good with your feet! This foot switch is made of rubbery plastic, is plenty strong to put up with any amount of stomping, and contains a snap switch. You can use the switch as either a "normally open" or "normally closed" type. Attached to the switch is a 2 meter long cable so you can wire it directly to your project.
PRODUCT ID: 504
This navigation switch is an intuitive way to add 5 button's worth of interfacing with a single component. Inside is 5 switches: left, right, up,...
This navigation switch is an intuitive way to add 5 button's worth of interfacing with a single component. Inside is 5 switches: left, right, up, down and 'select' (pressing down), all with a common ground pin. The package isn't exactly on a 0.1" grid, but we found that you can push it into a breadboard with a little bending and it snaps in nicely. We have a nice rubber cap that fits onto this joystick to make it very comfy...
PRODUCT ID: 735
Most of our customers love using the Arduino for prototyping, design and invention but find themselves stuck when trying to connect the Arduino to...
Most of our customers love using the Arduino for prototyping, design and invention but find themselves stuck when trying to connect the Arduino to the latest sensors, displays, controllers, interfaces, etc. as they are almost all 3.3V logic these days. We try to solve this problem by having all our breakout boards be 5V compatible or when that's not possible, including a level shifter chip but there are still thousands of tempting devices...
PRODUCT ID: 3221
This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and...
This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and forth constantly. Deciding whether or not to use this mini toggle switch? That's the easiest decision you'll make all day! This Mini Panel Mount SPDT Toggle Switch is great for any project where you have two options to select between. Maybe you'll be selecting between two voltages? Two audio...
PRODUCT ID: 3489
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a ~30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...
PRODUCT ID: 1536
Hey want to hear a really loud noise? Apply 3V to 5V to this buzzer module and you'll be rewarded with a loud 2KHz BEEEEEEEEEEEEEEEEEP. Unlike a...
Hey want to hear a really loud noise? Apply 3V to 5V to this buzzer module and you'll be rewarded with a loud 2KHz BEEEEEEEEEEEEEEEEEP. Unlike a plain piezo, this buzzer does not need an AC signal. Inside is a piezo plus the driver circuitry that makes it oscillate at 2KHz. On one hand, that makes it really great for integrating into projects because you don't need an oscillating control signal. On the other hand, you cannot change the...
PRODUCT ID: 2164
Ah the venerable 7805, who amongst us has not used this popular linear regulator? This big chunky regulator will help you get your 7-35V battery or...
Ah the venerable 7805, who amongst us has not used this popular linear regulator? This big chunky regulator will help you get your 7-35V battery or wall adapter down to a nice clean 5.0V with 2% regulation. Perfect for just about all electronics! This is the TO-220 version, with up to 1.5A current capability, and has internal current limiting + thermal shut-down protection which makes it sturdy and pretty much indestructible - at least...
PRODUCT ID: 3885
Hey, have you heard the good news? With Adafruit STEMMA boards you can easily and safely plug sensors and devices together, like this Adafruit STEMMA...
Hey, have you heard the good news? With Adafruit STEMMA boards you can easily and safely plug sensors and devices together, like this Adafruit STEMMA Speaker - Plug and Play Audio Amplifier . Like the name implies, it's got a class D audio amplifier on board, and our favorite little 1 Watt 8 ohm speaker. Connecting it up is easy - you only need ground, 3 to 5V power, and audio signal. The audio signal does not need to be AC coupled, we do...
PRODUCT ID: 1058
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them"...
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them" and then you see these little laser diode modules: what great timing! These encapsulated laser diodes are Class IIIa 5mW, with a 650nm red wavelength. They can be driven from 2.8V to 5.2V so they're great for your embedded electronics project. This particular module has a lens attached that will...
PRODUCT ID: 1739
This large (30mm diameter) piezo element is nicely enclosed with mounting holes so you can attach easily. Piezo elements convert vibration to voltage...
This large (30mm diameter) piezo element is nicely enclosed with mounting holes so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tones and alerts AND you can use it as a sensor, to detect fast movements like knocks. You can also use it under a drum pad to make a drum/crash sensor It's rated for up to 12Vpp use but you can also use 3 or 5V...
PRODUCT ID: 939
This is the cutest little microSD card reader/writer - but don't be fooled by its adorableness! It's wicked fast and supports up to 64 GB...
This is the cutest little microSD card reader/writer - but don't be fooled by its adorableness! It's wicked fast and supports up to 64 GB SDXC cards! Simply slide the card into the edge and plug it into your computer. No drivers are required, it shows up as a standard 'Mass Storage' device under any OS. You can swap cards while the USB port is kept plugged in. Comes with a handy little cord so you can attach it to your datalogger...
PRODUCT ID: 856
Need to add analog inputs? This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy...
Need to add analog inputs? This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use, and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the Raspberry Pi computer, because its fun to have analog inputs but the Pi does not have an ADC. We have a tutorial and code example for wiring this chip to a Raspberry Pi
PRODUCT ID: 3367
Hey, listen up! It's the world's smallest USB microphone! OK maybe it's not in the Guinness Record Book, but it is pretty darn small !...
Hey, listen up! It's the world's smallest USB microphone! OK maybe it's not in the Guinness Record Book, but it is pretty darn small ! This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with any computer, laptop, SBC, etc! Works great with a Raspberry Pi computer, but you can also use it with any other computer you want to record audio on. Simply plug it right in and you're...
PRODUCT ID: 2925
When you need a lot of options, you need a Mini 8-Way Rotary Selector Switch . This is basically a single-pole to 8-throw switch. As you rotate the...
When you need a lot of options, you need a Mini 8-Way Rotary Selector Switch . This is basically a single-pole to 8-throw switch. As you rotate the knob around, the middle pin will make contact with each of the outer pins. Rotary switches are very simple to use and are also nice and compact. This one is easy to panel mount, thanks to the included washer and hex nut. It has a T18-size shaft so you can pick one of our T18 knobs to go with it for...
PRODUCT ID: 3692
What is this TRS bit? T urtle R ock S tudios? T ransmission R aman S pectroscopy? Not quite, more like T ip- R ing- S leeve. This nifty,...
What is this TRS bit? T urtle R ock S tudios? T ransmission R aman S pectroscopy? Not quite, more like T ip- R ing- S leeve. This nifty, gold-plated connector is known by many names, phone plug, phone jack, headphone jack, jack plug , etc. Used to transmit stereo audio signals, these connectors are a mainstay in audio equipment, especially speakers and microphones. For audio, tip is left channel, and ring is right channel, and...
PRODUCT ID: 1740
This small (14mm diameter) piezo element is nicely enclosed so you can attach easily. Piezo elements convert vibration to voltage or voltage to...
This small (14mm diameter) piezo element is nicely enclosed so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tones and alerts AND you can use it as a sensor, to detect fast movements like knocks. You can also use it under a drum pad to make a drum/crash sensor It's rated for up to 9Vpp use but you can also use 3V square waves and its...
PRODUCT ID: 3954
By popular request, we've upgraded our popular Trellis elastomer button kits to now have a PCB with full color NeoPixel support! You heard that...
By popular request, we've upgraded our popular Trellis elastomer button kits to now have a PCB with full color NeoPixel support! You heard that right, no more single-color LEDs, you can now have any color you like under the fantastic rubbery button pads we sell. These 4x4 button pad boards are fully tile-able and communicate over I2C. With 5 address pins, you've got the ability to connect up to 32 together in any arrangement you like....
PRODUCT ID: 3972
Make your next custom USB cable a breeze with a USB Micro B Male Plug to 5-pin Terminal Block . If you need to connect to a device with a micro...
Make your next custom USB cable a breeze with a USB Micro B Male Plug to 5-pin Terminal Block . If you need to connect to a device with a micro USB plug or maybe make your own USB OTG device or custom cable of sorts - this adapter will come in very handy: no soldering required! Just use a small screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire, and re-tighten. All the pins are...
PRODUCT ID: 1439
A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 1681
The VS1053 is a multi-format audio codec chip, loved by many for its simplicity and power. CODEC stands for "Coder & Decoder" and...
The VS1053 is a multi-format audio codec chip, loved by many for its simplicity and power. CODEC stands for "Coder & Decoder" and that's pretty much what this little chip does - it can decode digital audio files such as MP3, FLAC, AAC, OGG and WAV as well as encode audio into digital formats (right now only WAV and OGG are supported for encoding). For many small microcontrollers, the mathematical calculations for decoding MP3...
PRODUCT ID: 1294
Add mega-storage in a jiffy using this 8 GB class 4 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters....
Add mega-storage in a jiffy using this 8 GB class 4 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters. Preformatted to FAT so it works out of the box with our projects. Tested and works great with our Wave shield, Data logger shield and GPS shield, and micro-SD adapter as well as any other device in the Adafruit shop that uses (micro)-SD cards! Please note! This is an SDHC card, and may not work with...
PRODUCT ID: 2138
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact...
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1" terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks...
PRODUCT ID: 1313
Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power....
Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our Wave shield or class D amplifier board. Speaker - 3" Diameter - 8 Ohm 1 Watt (0:01)
PRODUCT ID: 3883
These three Stacking Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you're in business! Great...
These three Stacking Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you're in business! Great for putting something a-top your ItsyBitsy, like this AirLift bitsy add-on. Also works great for 'short' Teensy boards - not Teensy 3.5 or 3.6 long style boards. Note: Kit includes two 14-pin and one 5-pin header. ItsyBitsy not included. Don't need all that stack?...
PRODUCT ID: 367
Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless...
Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 20, they're pretty handy so you'll want to keep them around. You can find an EAGLE cad package for these in switch-omron:B3F-10XX
PRODUCT ID: 2571
Give your 50 pin, 0.5mm pitch, devices a strrrreeeetch with this extension board. This 50pin FPC extension board has two 50-pin flex...
Give your 50 pin, 0.5mm pitch, devices a strrrreeeetch with this extension board. This 50pin FPC extension board has two 50-pin flex connectors, and an extension cable to add ~22cm (20cm cable plus 2cm board) Each order comes with one board a 20cm long, 50-pin 0.5mm pitch FPC cable and board. Works great with our 50pin TFTs, or anything else with the same kind of connector!
PRODUCT ID: 610
This power jack is designed to easily attach to a panel up to 8mm thick (0.315" or 5/16") and fit 2.1mm power plugs snugly and securely....
This power jack is designed to easily attach to a panel up to 8mm thick (0.315" or 5/16") and fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project enclosure. We like this jack in particular for its long body (so you can use it on thicker wooden panels), sturdy PCB spacer with 3 easy-to-solder eyes and 'forgiving' plastic lip that hides the drill hole.
PRODUCT ID: 501
Need a USB jack for charging or powering a project, but don't want to lug around a computer? This switching supply gives a clean regulated output...
Need a USB jack for charging or powering a project, but don't want to lug around a computer? This switching supply gives a clean regulated output at up to 1000mA! 110 or 240 input, so it works in any country. The plugs are "US 2-prong" style so you may need a plug adapter, but you can pick one up at any hardware store for a $1 or so. This adapter was specifically designed to provide 5.25V not 5V, but we still call it a 5V USB...
PRODUCT ID: 400
Breakaway header is like the duct tape of electronics, and this header is one better with extra long pins on both sides. This makes it great for...
Breakaway header is like the duct tape of electronics, and this header is one better with extra long pins on both sides. This makes it great for connecting things together that have two sockets - especially solderless breadboards. We also use these with our female-female socket jumpers to create female-male and male-male jumpers! Each pack contains 5 x 16-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1"...
PRODUCT ID: 3491
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...
PRODUCT ID: 1891
Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W...
Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value). We particularly like this cone as it's very simple and its plastic body is extremely lightweight and thin. Originally designed for 'talking' greeting...
PRODUCT ID: 3369
Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker . It's USB-only and does not require or use a...
Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker . It's USB-only and does not require or use a 3.5mm audio jack. You'll get great audio, even with a device that doesn't have a head phone jack. And since it is powered over USB, there's no need to charge it by other means, merely plug it into your desired device's USB port and listen to the audio flow. Compact and convenient to...
PRODUCT ID: 1445
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like...
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle! 16mm Panel Mount Momentary Pushbutton -...
PRODUCT ID: 2058
This slim and modern potentiometer is small and compact, yet looks good and has a nice feel. We hand selected the best knobs for your project in...
This slim and modern potentiometer is small and compact, yet looks good and has a nice feel. We hand selected the best knobs for your project in different sizes and varieties. This one is the Slim Metal Knob 10mm diameter x 10mm Tall (T18 Splines). It's a brushed aluminum knob with a shiny black (anodized?) coating. It kind of looks like the type of knob you'd find in a very fancy, modern kitchen. There's a...
PRODUCT ID: 2056
This is really the fanciest, best feeling knob we've ever seen. Using this knob sort of reminded us of driving along the Amalfi coast in a...
This is really the fanciest, best feeling knob we've ever seen. Using this knob sort of reminded us of driving along the Amalfi coast in a perfectly restored '65 Porsche - meaning we really, really liked it. We hand selected the best knobs for your project in different sizes and varieties. This one's the Solid Machined Metal Knob - 1" . It has a nice, weighted feel that spins easily and doesn't...
PRODUCT ID: 4133
Oh say can you see By the knob's early light... Sorry - we thought that was clever. And while it wasn't really, this potentiometer...
Oh say can you see By the knob's early light... Sorry - we thought that was clever. And while it wasn't really, this potentiometer definitely is! We've seen these in miniature synthesizers. They're bigger than a trim-pot, but smaller than a chunky potentiometer. Best of all no knob required! These have a knurled plastic grip with a white stripe marking. Use it as-is, for a low cost adjustment Comes as a standard 10K ohm...
PRODUCT ID: 756
Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics...
Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, they come in a pack of 10! Each transistor is a general purpose amplifier, model PN2222 (same pinout as the 2N3904) and has a standard EBC pinout. They can switch up to 40V at peak currents of 1A (not continuously, just peak!), with a...
PRODUCT ID: 2915
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love...
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") 4-Pole (TRRS) Audio Jack Terminal Block . TRRS stands for Tip, Ring, Ring, Sleeve. It has...
PRODUCT ID: 3627
What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a...
What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a LCD Controllable Black-out Panel)! They're often used for electric welding helmets because they can protect the welder's eyes from the bright sparks. Or – if you aren't a welder – they can be used to provide a "reveal" effect for your...
PRODUCT ID: 1134
To celebrate the 30th Anniversary of the invention of MIDI we're carrying these handy 5-pin MIDI jacks. They're what you see on the back of...
To celebrate the 30th Anniversary of the invention of MIDI we're carrying these handy 5-pin MIDI jacks. They're what you see on the back of nearly every synthesizer and drum machine. These are nice sturdy jacks, and breadboard-friendly, with all the pins on 0.1" spacing for easy wiring. This handy tutorial and wiring diagram will show you how to easily turn your Arduino into a MIDI controller! Also compatible with DINSYNC cables, if...
PRODUCT ID: 3218
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic red protective casing, and a red LED at the...
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic red protective casing, and a red LED at the tip of the switch, this Red LED Toggle Switch is sure to add some flair (and flare!) to your project. Often seen on control panels, now you can mimic a racing car, fighter jet, submarine status panel, factory controls, or anything really. They will control virtually any...
PRODUCT ID: 2791
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these...
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") Stereo Audio Jack Terminal Block . It's the most common size and style of audio connector, used in most headphones or basic...
PRODUCT ID: 976
Transistors are powerful little electronic switches, and when our little NPN transistors aren't power enough for your project, we have been known to...
Transistors are powerful little electronic switches, and when our little NPN transistors aren't power enough for your project, we have been known to use these beefy TIP120 Darlington transistors. Great for whenever you need to control medium to high-power electronics such as motors, solenoids, or 1W+ LEDs. We find them so handy, they come in a pack of 3! Each transistor is a general purpose amplifier, model TIP120 and has a BCE pinout. They can...
PRODUCT ID: 1477
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 4181
This cable is easy to understand - you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It's also really easy to...
This cable is easy to understand - you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It's also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It's also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection. Black wire connects to sleeve, white wire connects to tip. Note: The alligator clips may be Black/White or...
PRODUCT ID: 1440
A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 807
Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known...
Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it. Or you can breadboard something on your own! Each chip contains two full H-bridges (four half H-bridges). That means you can drive four...
PRODUCT ID: 755
This here is a 10 pack of the classic 1N4001 power blocking diode. These are good for reverse polarity protection (put it between your DC power jack...
This here is a 10 pack of the classic 1N4001 power blocking diode. These are good for reverse polarity protection (put it between your DC power jack and circuitry to avoid a negative-voltage that would zap your delicate electronics), kickback protection (place across your solenoids, relays & DC motors to safely discharge the spikes generated by the coils), general rectification, and more! These diodes can safely pass 1A average current...
PRODUCT ID: 4173
These three Short Male Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you're in...
These three Short Male Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you're in business! These headers are particularly cute and tiny and are designed to match perfectly with our shorty female header kit for ItsyBitsy. Note that you could use normal header with those headers, but these are short and don't need clipping. Note: Kit includes two 14-pin and one 5-pin header....
PRODUCT ID: 1505
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like...
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!
PRODUCT ID: 2098
Give your 40 pin, 0.5mm pitch, devices a strrrreeeetch with this extension board. This 40pin FPC extension board has two 40-pin flex connectors...
Give your 40 pin, 0.5mm pitch, devices a strrrreeeetch with this extension board. This 40pin FPC extension board has two 40-pin flex connectors (both are bottom contact type), and an extension cable to add ~22cm (20cm cable plus 2cm board) Each order comes with one board a 20cm long, 40-pin 0.5mm pitch FPC cable and board. Works great with our 40pin TFTs!
PRODUCT ID: 753
As any engineer will tell you, 0.1uF ceramic capacitors are the magic fairy dust of electronics - sprinkle them over your circuit schematics for good...
As any engineer will tell you, 0.1uF ceramic capacitors are the magic fairy dust of electronics - sprinkle them over your circuit schematics for good luck! But seriously, a 0.1uF capacitor right next to the VCC pin of your chips will improve stability by filtering out power supply spikes and noise that can cause flaky behavior. We love these little guys, they have 0.1" spacing so fit into any perf or breadboard, compact and good quality. We...
PRODUCT ID: 4031
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll...
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. The pins are on 0.1" spacing so it plugs very solidly ( and vertically! ) into a breadboard, perma-proto or perf-board. Works best if...
PRODUCT ID: 4227
Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power....
Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires with a connector on the end. It has a handy "Molex PicoBlade" 1.25mm pitch 2-pin cable, which makes plugging into a board easy. Or you can cut off the connector and just solder/clamp onto...
PRODUCT ID: 1332
Punch in your secret key into this numeric membrane keypad. This keypad has 4 buttons, and since every key has its own wire line, no matrix code is...
Punch in your secret key into this numeric membrane keypad. This keypad has 4 buttons, and since every key has its own wire line, no matrix code is required - just treat these like every day switches. The membrane is soft and has a removable paper backing to expose a strong adhesive so you can stick this on an enclosure and feed the cable through a slot. Its a simple keypad but that's why we like it. We include a 5-pin extra-long header...
PRODUCT ID: 4130
If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45...
If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45 Ethernet Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing Ethernet kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug...
PRODUCT ID: 4271
Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' away If...
Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' away If you're tired of the regular-old-twisty potentiometers we carry, why not slide over and try this slide pot? Most famously used on mixers and the transporter control panel on Star Trek, these slide pots are so cute and short at only 35mm. Use as a voltage divider, and you can visually gauge the voltage...
PRODUCT ID: 3395
This Panel Mount Right Angle 10K Linear Potentiometer w/ On-Off Switch is a two-in-one, with both a breadboard-friendly potentiometer and a switch....
This Panel Mount Right Angle 10K Linear Potentiometer w/ On-Off Switch is a two-in-one, with both a breadboard-friendly potentiometer and a switch. For the potentiometer-half, you've got a standard linear taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. It also comes equipped with an on/off switch at the beginning of the shaft's rotation. We like this one...
PRODUCT ID: 3083
Looking for a nice way to cool down your Raspberry Pi 3? Check out this 14x14x8 Heat Sink! This heat sink is made from high quality...
Looking for a nice way to cool down your Raspberry Pi 3? Check out this 14x14x8 Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface of the chip of any dust or grease then peel off the...
PRODUCT ID: 2102
This little 2x5 (10 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with any of our 10-pin IDC cables. It comes in two...
This little 2x5 (10 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with any of our 10-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...
PRODUCT ID: 3429
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...
PRODUCT ID: 1862
A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all...
A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate with this connector. You may get an off-white or black JST connector.
PRODUCT ID: 732
Add another 16 pins to your microcontroller using a MCP23017 port expander. The MCP23017 uses two i2c pins (these can be shared with other i2c...
Add another 16 pins to your microcontroller using a MCP23017 port expander. The MCP23017 uses two i2c pins (these can be shared with other i2c devices), and in exchange gives you 16 general purpose pins. You can set each of 16 pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any of the inputs change so you don't have to keep polling the chip. Use this chip from...
PRODUCT ID: 1502
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like...
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!
PRODUCT ID: 752
This 1.27mm pitch, 2x5 male SMT Box Header is the same one used on our SWD Cable Breakout Board. The header alone is great if you want to...
This 1.27mm pitch, 2x5 male SMT Box Header is the same one used on our SWD Cable Breakout Board. The header alone is great if you want to incorporate this piece of hardware with your own software. We're specifically selling it so you can solder it onto our nRF52 Feather to add SWD debug/connect capabilities. You could also straighten out the SMT pins to solder into a thru-hole connector. This little guy will snap right into any 10-pin...
PRODUCT ID: 1683
Push once to turn on, push again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's...
Push once to turn on, push again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's breadboard friendly and more fun than a power switch. Can reliably handle up to 500mA and up to 50V. This is a really satisfying switch. The leads are not on a perfect 0.1" grid so for use with a breadboard just bend the leads out just a tad and snap into a solderless breadboard or perfboard.
PRODUCT ID: 2057
This slim and modern potentiometer is small and compact, yet looks good and has a nice feel. We hand selected the best knobs for your project in...
This slim and modern potentiometer is small and compact, yet looks good and has a nice feel. We hand selected the best knobs for your project in different sizes and varieties. This one is the Slim Metal Knob 10mm diameter x 15mm Tall (T18 Splines). It's a brushed aluminum knob with a shiny black (anodized?) coating. It kind of looks like the type of knob you'd find in a very fancy, modern kitchen. There's a...
PRODUCT ID: 4174
These three Short Female Headers alone are, well, lonely. But pair them with any of our ItsyBitsy boards, and you're...
These three Short Female Headers alone are, well, lonely. But pair them with any of our ItsyBitsy boards, and you're in business! These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your ItsyBitsy project takes up, but still maintain that flexible configuration. "Normal" socket headers have an 8.5mm body height so this saves...
PRODUCT ID: 1479
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 550
Keep your electronics from going barefoot, give them little rubber feet! These small sticky bumpers are our favorite accessory for any electronic kit...
Keep your electronics from going barefoot, give them little rubber feet! These small sticky bumpers are our favorite accessory for any electronic kit or device. They are sticky, but not impossible to remove. They're small enough to fit onto any board, and have just enough height to give clearance to thru-hole soldered components. We love them so much we include them free with every Arduino we sell, but we've also had requests to carry...
PRODUCT ID: 1831
This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a...
This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-points, so you can plug it into a breadboard or perfboard. Once you're done prototyping, you can drill a hole into your project box and mount...
PRODUCT ID: 1442
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 1481
This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand,...
This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand, it's just a gigantic resistor. On the other hand, it's flexible, light, and can be wrapped around a project. Originally designed for portable wearable heating pads, this fabric can be used for wearables, weather balloons, diy-bio projects, thermal cycling for materials testing, etc. The...
PRODUCT ID: 4855
This 0.1mm pitch 2x2 Female Header is the perfect boost to use with boards that use the 4-pin 'PoE' header on the Raspberry...
This 0.1mm pitch 2x2 Female Header is the perfect boost to use with boards that use the 4-pin 'PoE' header on the Raspberry Pi 3 and 4, like the Raspberry Pi PoE HAT! It's a great pairing to the 2x20 socket riser header to get a full lift. Use this wee GPIO header along with a 40-pin stacking header to utilize the PoE HAT with another add-on board. This header plops on the 4-pin header of the Raspberry Pi. Great...
PRODUCT ID: 4184
You know those party platters you see at fancy events, where there's like sliced carrots on one side, and chunks of cheese on another, all...
You know those party platters you see at fancy events, where there's like sliced carrots on one side, and chunks of cheese on another, all divided up lovely? OK this is the exact same thing but for 6mm tactile buttons. You will never feel constrained by button colors again with this button party, lots of colors, in a handy carry case. Little clicky switches are standard input "buttons" on electronic projects. These work best in a...
PRODUCT ID: 1489
Slim clicky momentary switches are standard input "buttons" on electronic projects. These are half the width of classic 6mm tactile...
Slim clicky momentary switches are standard input "buttons" on electronic projects. These are half the width of classic 6mm tactile switches so they line up better on a breadboard, just plug them into every-other row. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The two pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack...
PRODUCT ID: 3487
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...
PRODUCT ID: 2166
Need a nice little 3.3V regulator? We rather like the very-low-dropout L4931 from ST! This little guy will help you get your 4-20V battery or wall...
Need a nice little 3.3V regulator? We rather like the very-low-dropout L4931 from ST! This little guy will help you get your 4-20V battery or wall adapter down to a nice clean 3.3V with 2% regulation. Perfect for just about all electronics! This is a TO-92 package version, with up to 250mA current capability, and has internal current limiting + thermal shut-down protection which makes it sturdy and pretty much indestructible - at least...
PRODUCT ID: 3102
Sometimes a simple analog control device can be the perfect tactile solution for your project, but they can be surprisingly hard to come by. Luckily...
Sometimes a simple analog control device can be the perfect tactile solution for your project, but they can be surprisingly hard to come by. Luckily we've found a low cost, quality Mini Analog Joystick to fill you directional analog input needs! Unlike most arcade-style joysticks which come with four clicking switches, this product has two 10KΩ potentiometers and a spring-back system. You can get a full 50 degrees in both X and Y...
PRODUCT ID: 383
A ZIF (Zero Insertion Force Socket) allows you to insert and remove chips easily from an existing circuits. These are often used for chip programmers...
A ZIF (Zero Insertion Force Socket) allows you to insert and remove chips easily from an existing circuits. These are often used for chip programmers or when you need to test a chip without damaging it. Move the lever up and chips drop right in. Move the lever down to 'latch' the chip in place. This socket is designed for DIP chips of up to 40 pins and up to 0.6" wide. So really, its good for any size chip you'll find....
PRODUCT ID: 3968
Hear the good news! This speaker is a great addition to any audio project where you need a 4 Ohm impedance and 3W or less of power. At 40mm...
Hear the good news! This speaker is a great addition to any audio project where you need a 4 Ohm impedance and 3W or less of power. At 40mm diameter it has a more square-ish shape, but a smaller face. Sound quality and volume are nicely sandwiched between our Thin Plastic Speaker with Wires and the honkin' 20W 4 Ohm Full Range Speaker. This bite-sized speaker comes with two long color-coded wires to solder to or plug into a...
PRODUCT ID: 819
Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need...
Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need a basic sensor. They are always 'tactile' (clicky feeling), and 'momentary' (the switch closes when pressed, then snaps open once released). They come in a few different varieties (mostly having to do with the contacts and how big the actuator is). This microswitch has a flat metal...
PRODUCT ID: 1503
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like...
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!
PRODUCT ID: 3366
Headers are like the duct tape of electronics. They're great for connecting things together, soldering to perf-boards, sockets for wires or...
Headers are like the duct tape of electronics. They're great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of five! Stacking headers are a twist on the standard/common male and female header sets. In this case you have one header that has a socket on one end, and a long...
PRODUCT ID: 382
A ZIF (Zero Insertion Force Socket) allows you to insert and remove chips easily from an existing circuits. These are often used for chip programmers...
A ZIF (Zero Insertion Force Socket) allows you to insert and remove chips easily from an existing circuits. These are often used for chip programmers or when you need to test a chip without damaging it. Move the lever up and chips drop right in. Move the lever down to 'latch' the chip in place. This socket is designed for DIP chips of up to 28 pins and 0.3" wide. What's nice about it is it can snap into an existing circuit board...
PRODUCT ID: 3662
If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni...
If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero, Bonnet, HAT or pHAT. Make sure to carefully read Pimoroni's guide for fitting hammer headers. The...
PRODUCT ID: 3844
Punch in your secret key (or Jenny's number) into this numeric matrix keypad. This keypad has 16 buttons, arranged in a telephone-line 4x4...
Punch in your secret key (or Jenny's number) into this numeric matrix keypad. This keypad has 16 buttons, arranged in a telephone-line 4x4 grid. The keys are connected into a matrix, so you only need 8 microcontroller pins (4-columns and 4-rows) to scan through the pad. Check the tutorials tab for links to an Arduino library and example code. We include some header so you can plug this into a breadboard with ease, some light...
PRODUCT ID: 3391
This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a log taper 10K ohm potentiometer, with a grippy shaft. It's...
This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a log taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-points, so you can plug it into a breadboard or perfboard. Once you're done prototyping, you can drill a hole into your project box and mount the potentiometer...
PRODUCT ID: 3431
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...
PRODUCT ID: 1476
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 2780
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This...
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 220Ω Resistors. More specifically, they are carbon film , through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors. Whew! These are super common and great for use in any kit, breadboard, perf-board, or other project. We got ones with...
PRODUCT ID: 1441
A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 3599
Transistors are powerful little electronic switches, and we really like these NPN and PNP transistors whenever we need to control medium-power...
Transistors are powerful little electronic switches, and we really like these NPN and PNP transistors whenever we need to control medium-power electronics, such as small motors, solenoids, or IR LEDs. We find them so handy we threw together a mix-and-match bag of PN2222 and PN2907! You get 5 x NPN and 5 x PNP, very handy for your class B amplifier, high or low side control, LED strips, what-have-you. Each transistor is a general purpose...
PRODUCT ID: 3105
This Mini Illuminated Momentary Power Button is an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to...
This Mini Illuminated Momentary Power Button is an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to add a tactile switch and a colorful universal power symbol to your project. The tact switch is about the same size as 6mm tactile switches and can snap into a breadboard. There are an additional two pins that connect to the anode and cathode of a small LED that shines through the top. Note...
PRODUCT ID: 2137
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact...
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1" terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks...
PRODUCT ID: 2055
Round and round it goes, this nice round "scrubber" knob is the perfect mate to a rotary encoder. It's got a wide 34.7mm diameter...
Round and round it goes, this nice round "scrubber" knob is the perfect mate to a rotary encoder. It's got a wide 34.7mm diameter with a nice finger groove on its face so it's easy to turn with just one finger. It works best with our rotary encoder, just snap it on and away you go. Please note: this knob won't work with our potentiometers which have T18 spline shafts! While rotary encoders look similar to...
PRODUCT ID: 4697
A new tiny squishy delight! This Black Rubber Joystick Nubbin Cap is the perfect add-on to any of your projects with a 5-way navigation joystick,...
A new tiny squishy delight! This Black Rubber Joystick Nubbin Cap is the perfect add-on to any of your projects with a 5-way navigation joystick, like our Adafruit Mini Color TFT with Joystick FeatherWing or Adafruit 128x64 OLED Bonnet for Raspberry Pi. Fits perfectly on classic 5-way navigation joysticks like this one. It's solid, sturdy, and presses on firmly. We especially dig the cute directional etching. Pop it onto a...
PRODUCT ID: 4361
Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a...
Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. Each jack comes with two solder eyelets and a panel mounting hex-nut. They made of all-metal construction with paper phenolic spacers. 3.5mm connectors...
PRODUCT ID: 1185
OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a...
OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...
PRODUCT ID: 1010
Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless...
Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. These buttons are bigger than the 6mm ones we carry, and come in a pack of 15. Each button comes with a candy-colored square cap that snaps on. You get three of each...
PRODUCT ID: 2165
Ah the esteemed LD1117, who amongst us has not used this popular low drop voltage regulator? This big chunky regulator will help you get your...
Ah the esteemed LD1117, who amongst us has not used this popular low drop voltage regulator? This big chunky regulator will help you get your 4-15V battery or wall adapter down to a nice clean 3.3V with 1% regulation. Perfect for just about all electronics! This is the TO-220 version, with up to 800mA current capability, and has internal current limiting + thermal shut-down protection which makes it sturdy and pretty much...
PRODUCT ID: 977
Get the most out of your regulators, transistors and other TO-220 packaged chips by clipping on a heat-sink. Your transistor or regulator may...
Get the most out of your regulators, transistors and other TO-220 packaged chips by clipping on a heat-sink. Your transistor or regulator may advertise it can handle high currents but when multiplied by the drop voltage, the Wattage may be too high for the bare chip! Most TO-220's can disipate about 2W's worth without a sink. This basic, and easy-to-use ~25°C/W sink will let you burn about 3 Watts of power through a TO-220 (assuming...
PRODUCT ID: 1684
Push once to turn one side on, push again to turn off, push again to turn the other side on, one last push and its off again! It's basically a...
Push once to turn one side on, push again to turn off, push again to turn the other side on, one last push and its off again! It's basically a push-button toggle switch that connects and disconnects the middle pin from either of the two side switches with every click. This clicky switch makes a great power switch or mode toggler. We like this switch because it's breadboard friendly and more fun than a power switch. Can reliably handle up...
PRODUCT ID: 3220
This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and...
This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and forth constantly. Deciding whether or not to use this mini toggle switch? That's the easiest decision you'll make all day! This Mini Panel Mount DPDT Toggle Switch is great for any project where you need two switches each with two options to select between. Maybe you'll be selecting between...
PRODUCT ID: 4432
As technology changes and adapts, so does Adafruit, and speaking of adapting , this right angle adapter is USB C socket-to-plug. USB C...
As technology changes and adapts, so does Adafruit, and speaking of adapting , this right angle adapter is USB C socket-to-plug. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB A correctly the first time? Works great with any device or cable that has a USB C port, even up to USB 3.1...
PRODUCT ID: 3118
Make your own custom HDMI cable or HDMI interface with ease, using this HDMI Terminal Block Breakout . You get a nice solid PCB with an HDMI plug and...
Make your own custom HDMI cable or HDMI interface with ease, using this HDMI Terminal Block Breakout . You get a nice solid PCB with an HDMI plug and two strips of terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. If you just need a plain HDMI cable, we have plenty and it's less expensive to just buy a standard cable than DIY it. So, we recommend this adapter when you have some...
PRODUCT ID: 3488
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and they require a 30mm diameter hole for mounting. Thus, they are sometimes referred to as 30mm...
PRODUCT ID: 2202
An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 8 pin...
An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 8 pin 0.3" wide version. Best used with chips that have 8 pins (2x4) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you...
PRODUCT ID: 3628
This is the USB-A Male Plug to 5-pin Terminal Block . If you need to connect to a device with a USB Jack, maybe make your own USB stick or...
This is the USB-A Male Plug to 5-pin Terminal Block . If you need to connect to a device with a USB Jack, maybe make your own USB stick or custom cable of sorts - this adapter will come in very handy! No soldering required. Just use a small screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire, and re-tighten. The terminal block itself is removable from the body. It's more durable than...
PRODUCT ID: 4445
Listen up! This single 2.8" x 1.2" speaker is the perfect addition to any audio project where you need 4 ohm impedance and...
Listen up! This single 2.8" x 1.2" speaker is the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. This speaker does not come with a connector on the end, it's just plain bare wires! Works peachy-keen with any of our audio amps as well, such as the MAX98306, TS2012 or...
PRODUCT ID: 2215
Keep your microcontroller tickin' with a a fancy timing crystal. This 16.000 MHz model comes in a HC49/US 'short style' standard package...
Keep your microcontroller tickin' with a a fancy timing crystal. This 16.000 MHz model comes in a HC49/US 'short style' standard package and is breadboard friendly and easy to use with any microcontroller or device that requires an external crystal. We even include two 20pF capacitors! The crystal has 30PPM tolerance, 50PPM stability so it's good even for high precision needs (USB timing, long-term time-keeping, RF/PLL/VCO...
PRODUCT ID: 2195
We like capacitors so much we made a kids show about them. They're super handy and it's really helpful to have a variety...
We like capacitors so much we made a kids show about them. They're super handy and it's really helpful to have a variety lying around to pick and choose from. This is a 10 pack of 10uF 50v capacitors, so they can be used with any DC voltage up to 50V. They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are...
PRODUCT ID: 2781
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This...
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 470Ω Resistors. More specifically, they are carbon film , through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors. Whew! These are super common and great for use in any kit, breadboard, perf-board, or other project. We got ones with...
PRODUCT ID: 2136
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact...
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1" terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks...
PRODUCT ID: 3490
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 30mm diameter hole for mounting. Thus they are sometimes referred to as 30mm...
PRODUCT ID: 2270
The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular...
The "poor woman's" Raspberry Pi A+ / B+ / Pi 2 cobbler! This combo of 2x20 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A+/B+/Pi 2 (40 pins). It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so...
PRODUCT ID: 2913
If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that with an Ethernet Jack - this adapter will come in very handy! No soldering...
If you need to connect an RJ45 cable (a.k.a Ethernet) to a board that with an Ethernet Jack - this adapter will come in very handy! No soldering required. Just use a slim screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire and re-tighten. Note that these aren't recommended for actual Ethernet traffic, especially long term...but for basic power/data distribution, RJ45's are great! This is the Ethernet...
PRODUCT ID: 4208
If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST...
If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. This connector can be used with Qwiic boards and cables, to easily connect sensors and drivers from one board...
PRODUCT ID: 915
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and...
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a blue plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the blue...
PRODUCT ID: 818
Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need...
Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need a basic sensor. They are always 'tactile' (clicky feeling), and 'momentary' (the switch closes when pressed, then snaps open once released). They come in a few different varieties (mostly having to do with the contacts and how big the actuator is). This microswitch has a flat metal...
PRODUCT ID: 3104
This Mini Illuminated Momentary Power Button it an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to...
This Mini Illuminated Momentary Power Button it an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to add a tactile switch and a colorful universal power symbol to your project. The tact switch is about the same size as 6mm tactile switches and can snap into a breadboard. There are an additional two pins that connect to the anode and cathode of a small LED that shines through the top. Note...
PRODUCT ID: 1789
This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy...
This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-points, so you can plug it into a breadboard or perfboard. Once you're done prototyping, you can drill a hole into your project box and mount the...
PRODUCT ID: 1056
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them"...
You have some frickin' sharks at your lair, and you're thinking "it would be really great if I could attach some lasers to them" and then you see these little laser diode modules: what great timing! These encapsulated laser diodes are Class IIIa 5mW, with a 650nm red wavelength. They can be driven from 4.8V to 5.2V so they're great for your embedded electronics project. This module in particular is designed to be...
PRODUCT ID: 820
Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need...
Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need a basic sensor. They are always 'tactile' (clicky feeling), and 'momentary' (the switch closes when pressed, then snaps open once released). They come in a few different varieties (mostly having to do with the contacts and how big the actuator is). This microswitch has a 3"...
PRODUCT ID: 917
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and...
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a white plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the...
PRODUCT ID: 1468
Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is...
Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is less messy than thermal glues or pastes because the thickness is even across the area. A perfect match for our range of small heat sinks, either in aluminum or copper. Comes in a square of 80mm x 80mm (3" square) - but can be cut into any shape or size. For more information about 3M's 8810...
PRODUCT ID: 4272
Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' away If...
Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' away If you're tired of the regular-old-twisty potentiometers we carry, why not slide over and try this slide pot? Most famously used on mixers and the transporter control panel on Star Trek, these slide pots are not too long at only 45mm. Use as a voltage divider and you can visually gauge the voltage from...
PRODUCT ID: 2823
If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and...
If we could eat headers we'd have them for breakfast, lunch, and dinner. But we can't :( So we're making the best of it and selling them! This 2x20-pin strip, right-angle female header is a perfect companion piece to our 2x20-pin Dual Male Header. It's a great way to add right-angle capability to a 2x20 pin circuit board either by attaching the right-angle male headers to the board and having a right-angle female...
PRODUCT ID: 2784
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This...
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 10K Ω Resistors. More specifically, they are carbon film , through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors. Whew! These are super common and great for use in any kit, breadboard, perf-board, or other project. We got ones with...
PRODUCT ID: 3432
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...
PRODUCT ID: 2693
Add speedy mega-storage in a jiffy using this 16 GB Class 10 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or...
Add speedy mega-storage in a jiffy using this 16 GB Class 10 micro-SD card. It comes with a SD adapter so you can use it with any of our shields or adapters! Preformatted to FAT so it works out of the box with our projects. Works great with any device in the Adafruit shop that uses micro-SD cards. Ideal for use with Raspberry Pi, BeagleBone Black and other single-board computers that use a microSD card for storage Please note! This is an SDHC...
PRODUCT ID: 1009
Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless...
Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. These buttons are bigger than the 6mm ones we carry, and come in a pack of 15. Each button comes with a candy-colored round cap that snaps on. You get three of each...
PRODUCT ID: 4294
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This...
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 1.0KΩ Resistors. More specifically, they are carbon film , through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors. Whew! These are super common and great for use in any kit, breadboard, perf-board, or other project. We got ones with...
PRODUCT ID: 1152
Quick connector wire sets will make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.11"...
Quick connector wire sets will make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.11" quick-connects pre-crimped onto 20cm long wires. The wires are then terminated together in a JST 2.5mm/0.1" spaced 2-pin connector (we don't have the exact part number yet for the connector but you can just use 0.1" header) Of course you can cut this off if you don't have use for...
PRODUCT ID: 4212
If you need to add a panel-mount connection for USB B, but don't have the time or tools to cut a custom oval or square hole, this Round...
If you need to add a panel-mount connection for USB B, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da! Now you...
PRODUCT ID: 1863
This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch...
This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There's two ground pins, one 'switched' power pin, and one pin that is always on. This is compatible with the "JST PH 2-pin" connectors we use in our battery packs.. Mates perfectly with all our 1-cell...
PRODUCT ID: 1785
Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers...
Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers you've seen. Instead, a small metal rod is wrapped with the voice coil. When current is pulsed through the coil, the magnetic field causes a piece of metal to expand and contract - and if it's pressed against a surface it turns the transducer into a speaker! Often these size transducers are pressed...
PRODUCT ID: 1443
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 1478
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 4423
Totaling 560 pieces, this JST-XH Connector Kit is a must-have for your workstation. You'll have enough sockets and headers to...
Totaling 560 pieces, this JST-XH Connector Kit is a must-have for your workstation. You'll have enough sockets and headers to fuel your maker tendencies for days on end! These connectors are really common in electronics, we use the 2 pin ones for our arcade quick-connects. Since they are 2.5mm they are very close to and will fit 0.1" headers - so you can use nicely with perf-boards, breadboards, plain header, etc....
PRODUCT ID: 4293
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This...
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 100Ω Resistors. More specifically, they are carbon film , through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors. Whew! These are super common and great for use in any kit, breadboard, perf-board, or other project. We got ones with...
PRODUCT ID: 593
Add another 8 pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two i2c pins (these can be shared with other i2c...
Add another 8 pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two i2c pins (these can be shared with other i2c devices), and in exchange gives you 8 general purpose pins. You can set each of 8 pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any of the inputs change so you don't have to keep polling the chip. Use this chip from 2.7-5.5V...
PRODUCT ID: 4422
Totally 220 pieces, this JST-PH Connector Kit is a must-have for your workstation. You'll have enough sockets and plugs to...
Totally 220 pieces, this JST-PH Connector Kit is a must-have for your workstation. You'll have enough sockets and plugs to fuel your maker tendencies for days on end! These connectors are really common in electronics, we use the 2 pin ones for our batteries and battery packs. The 3 pin and 4 pin are used for STEMMA connectors. The 4 pin size is even compatible with Grove! They are large enough you can crimp without...
PRODUCT ID: 1188
OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a...
OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...
PRODUCT ID: 3009
In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains ten 36-pin short break-away...
In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains ten 36-pin short break-away male headers, 0.1" pitch. These headers are very short for matching with our short female headers. Normal male headers are a little longer and need to be cut down to be as slim as possible. Breakaway headers are like the duct tape of electronics. They're great for connecting things together,...
PRODUCT ID: 724
Nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-Wire...
Nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-Wire connections. These particular 3.5mm terminal blocks are our favorite: big enough for a range of wire gauges, easy to adjust with a screwdriver, and not too chunky. The only down-side is that they do not fit into 2.5mm spaced holes (they're 3.5mm spaced) - but they do fit in most perf/proto-board if...
PRODUCT ID: 4431
Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button...
Little clicky switches are standard input "buttons" on electronic projects. These are just like our Colorful Round Tactile Button Switch Assortment, but already assembled onto a PCB - they even have a pull-up resistor installed! The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. Each button comes with a candy-colored round cap snapped on. You get one of each color-- blue,...
PRODUCT ID: 1092
Squeeze once to turn on, squeeze again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because...
Squeeze once to turn on, squeeze again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's easy to embed in a seam for easily powering up/off wearable and fabric projects. Can handle up to 14V and 2 Amps! This is a really satisfying switch. As of May 20th, the dimensions of this switch are: Length of wires: 190mm / 7.5"Dimensions of body: 16mm x 15mm x 6mm / 0.6" x 0.6"...
PRODUCT ID: 2203
An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 16 pin...
An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 16 pin 0.3" wide version. Best used with chips that have 16 pins (2x8) and have 0.3" pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you...
PRODUCT ID: 4743
These two SMT Socket Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! ...
These two SMT Socket Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! These headers are particularly cute and slim and are designed to match with FeatherWings. It's harder to solder than thru-hole type headers, but for reflow-friendly builds these headers are recommended! We use these on all types of 'Wings, from the CRICKIT...
PRODUCT ID: 3124
Make your own custom DE-15 cable or DE-15 interface with ease, using this DE-15 Socket to Terminal Block Breakout . You get a nice solid PCB with an...
Make your own custom DE-15 cable or DE-15 interface with ease, using this DE-15 Socket to Terminal Block Breakout . You get a nice solid PCB with an DE-15 socket and two strips of terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. Perfect for when you need a non-standard wiring setup or interfacing to a device with a VGA interface (that's what these connectors were used for the most)...
PRODUCT ID: 491
A button is a button, and a switch is a switch, but this LED illuminated arcade buttons is in a class of its own. It's similar in size to an...
A button is a button, and a switch is a switch, but this LED illuminated arcade buttons is in a class of its own. It's similar in size to an arcade button (and will fit in holes drilled for 'standard' 30mm buttons) but has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic, and a lamp holder fits inside. These were originally designed for...
PRODUCT ID: 4219
Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' away If...
Slip slidin' away Slip slidin' away You know the nearer your resistance The more you're slip slidin' away If you're tired of the regular-old-twisty potentiometers we carry, why not slide over and try this slide pot? Most famously used on mixers and the transporter control panel on Star Trek, these slide pots are not too long at only 75mm. Use as a voltage divider and you can visually gauge the voltage from...
PRODUCT ID: 916
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and...
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a red plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the red...
PRODUCT ID: 3629
This is the USB-A Female Socket to 5-pin Terminal Block . If you need to connect to a device with a USB Jack, maybe make your own USB host...
This is the USB-A Female Socket to 5-pin Terminal Block . If you need to connect to a device with a USB Jack, maybe make your own USB host connector, extension cable, or custom cable of sorts - this adapter will come in very handy! No soldering required. Just use a small screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire, and re-tighten. The terminal block itself is removable from the...
PRODUCT ID: 1504
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like...
OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it anyways – look at that lovely rounded shape, that elegant bevel. If you're going to go with a momentary pushbutton, let it be this one! The button is a normally-open micro-switch. When pressed, the contacts short closed and Bob's your uncle!
PRODUCT ID: 1589
This Big Freaking Capacitor is just the trick when you have a lot of current sloshing around your project. They'll help smooth out voltage spikes...
This Big Freaking Capacitor is just the trick when you have a lot of current sloshing around your project. They'll help smooth out voltage spikes by providing a little buffering. We use these to help stabilize solar panels on our solar Lipoly charger kit, but they'd also be great with our servo driver boards or on the power connection to our 5V 10A power supply 4700uF capacitance for up to 10V power supplies. 4700uF 10v Electrolytic...
PRODUCT ID: 442
Always have the right SMT components at your hand with this awesome 0603 Resistor and Capacitor book set! This book has nice translucent pages filled...
Always have the right SMT components at your hand with this awesome 0603 Resistor and Capacitor book set! This book has nice translucent pages filled with cut tape 0603 SMT components , sorted, labeled and ready to go. This book has 63 5% resistor values, 3025 parts and 17 capacitor values, 700 parts . The nice thing is that you get a good distribution of the resistors, with more 1K and 10KΩ and fewer of the really high values. 63 5% Yageo...
PRODUCT ID: 4726
This socket is good for any SOIC/SOP Wide - body 8 pin chip in a 200mil wide body. Simply flip open the latch, insert the chip, and flip down the...
This socket is good for any SOIC/SOP Wide - body 8 pin chip in a 200mil wide body. Simply flip open the latch, insert the chip, and flip down the latch to secure it in place. The chip is held securely against gold 'fingers' (no, stop, Mr. Bond! It's not that Goldfinger!) in the socket. The bottom footprint matches the same SOIC footprint so you can solder this onto an existing PCB as long as you have the clearance for the...
PRODUCT ID: 2790
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these...
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") Stereo Audio Plug Terminal Block . It's the most common size and style of audio connector, used in most headphones or...
PRODUCT ID: 4186
We've got plenty of round and square buttons, but these LED Illuminated Triangle Pushbuttons are welcome to the party. These make us...
We've got plenty of round and square buttons, but these LED Illuminated Triangle Pushbuttons are welcome to the party. These make us think of 1960's or 70's Sci-Fi control board buttons. As everyone knows, triangular buttons are the most retro-futuristic of all button shapes. Get 6 of them together for a cool hexagonal arrangement, or just have one triangle at a time. These buttons are medium-sized, large...
PRODUCT ID: 3430
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...
PRODUCT ID: 1467
Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is...
Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is less messy than thermal glues or pastes because the thickness is even across the area. A perfect match for our range of small heat sinks, either in aluminum or copper. Comes in a square of 25mm x 25mm (1" square) - but can be cut into any shape or size. For more information about 3M's 8810...
PRODUCT ID: 3433
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LEDs built right in! That's right, you'll be button-mashing amidst a wash of beautiful light with these lil' guys. They're the same size as common miniature arcade controls, and require a 24mm diameter hole for mounting. Thus they are sometimes referred to as 24mm diameter. The...
PRODUCT ID: 4183
This product is really annoying to have to write a description for because it's really something you have to touch to understand! Instead of a...
This product is really annoying to have to write a description for because it's really something you have to touch to understand! Instead of a hard plastic actuator-button, these have a soft molded silicone button top. The underlying switch is still a clicky dome-switch but you have this nice soft grippy button for your fingers. It's incredibly satisfying to press and adds a nice upgrade to what is normally a plain tactile switch. We use...
PRODUCT ID: 1192
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of...
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat white plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...
PRODUCT ID: 1187
OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a...
OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...
PRODUCT ID: 1616
This item is just for the Trellis driver PCB assembly: LEDs and buttons not included. Trellis is an open source backlight keypad driver system. It is...
This item is just for the Trellis driver PCB assembly: LEDs and buttons not included. Trellis is an open source backlight keypad driver system. It is easy to use, works with any 3mm LEDs and eight tiles can be tiled together on a shared I2C bus. This PCB is specially made to match the Adafruit 4x4 elastomer keypad. Each Trellis PCB has 4x4 pads and 4x4 matching spots for 3mm LEDs. The circuitry on-board handles the background key-presses and LED...
PRODUCT ID: 816
Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come...
Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or other PCBs and work nicely with our female-ended wire sets. Comes in a set of four pieces, each piece is 3 rows by 4 rows. You can stack these next to each other in any direction. We...
PRODUCT ID: 4213
If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this Micro USB...
If you need to add a panel-mount connection but don't have the time or ability to cut a custom oval or square hole, this Micro USB B Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da!...
PRODUCT ID: 3413
If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni...
If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. They come in both male and female, and use crafty little retaining nubbins to grip tightly into the holes on the PCB. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to...
PRODUCT ID: 3310
DIY? How about D-I-Wire! This barrel jack plug is great for adding a common power connector to the end of your wires. The jack is compatible...
DIY? How about D-I-Wire! This barrel jack plug is great for adding a common power connector to the end of your wires. The jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder terminals and a crimp strain relief. Nifty, tidy, and practical.
PRODUCT ID: 1784
Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers...
Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers you've seen. Instead, a metal rod is wrapped with the voice coil. When current is pulsed through the coil, the magnetic field causes a piece of metal to expand and contract - and if it's pressed against a surface it turns the transducer into a speaker! Often these size transducers are pressed up...
PRODUCT ID: 4511
If you need to connect an RJ-45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet jack - this adapter will come in very...
If you need to connect an RJ-45 cable (a.k.a Ethernet) to a board that doesn't have an Ethernet jack - this adapter will come in very handy! No soldering required - Just flick up the little levers and slide in your stranded or solid-core wire. Note that these aren't recommended for high-speed Ethernet traffic, especially long term, for basic power/data distribution, RJ-45's are great! This is an Ethernet (RJ-45) Female...
PRODUCT ID: 4259
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this Round...
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da! Now you...
PRODUCT ID: 2193
We like capacitors so much we made a kids show about them. They're super handy and it's really helpful to have a variety...
We like capacitors so much we made a kids show about them. They're super handy and it's really helpful to have a variety lying around to pick and choose from. This is a 10 pack of 100uF 16v capacitors so they can be used with any DC voltage up to 16V. They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are...
PRODUCT ID: 597
Add a mini printer to any microcontroller project with this very cute thermal printer. Thermal printers are also known as receipt printers,...
Add a mini printer to any microcontroller project with this very cute thermal printer. Thermal printers are also known as receipt printers, they're what you get when you go to the ATM or grocery store. Now you can embed a little printer of your own into an enclosure. This printer is ideal for interfacing with a microcontroller, you simply need a 3.3V-5V TTL serial output from your microcontroller to print text, barcodes, bitmap graphics,...
PRODUCT ID: 4308
This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand,...
This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand, it's just a gigantic resistor. On the other hand, it's flexible, light, and can be wrapped around a project. Originally designed for portable wearable heating pads, this fabric can be used for wearables, weather balloons, DIY-bio projects, thermal cycling for materials testing, etc. The...
PRODUCT ID: 3307
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic green protective casing, and a green LED at...
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic green protective casing, and a green LED at the tip of the switch, this Green LED Toggle Switch is sure to add some flair (and flare!) to your project. Often seen on control panels, now you can mimic a racing car, fighter jet, submarine status panel, factory controls, or anything really. They will control virtually any...
PRODUCT ID: 441
Always have the right SMT components at your hand with this awesome 0805 Resistor and Capacitor book set! This book has nice translucent pages filled...
Always have the right SMT components at your hand with this awesome 0805 Resistor and Capacitor book set! This book has nice translucent pages filled with cut tape SMT 0805 components , sorted, labeled and ready to go. This book has 63 5% resistor values, 3025 parts and 17 capacitor values, 700 parts . The nice thing is that you get a good distribution of the resistors, with more 1K and 10KΩ and fewer of the really high values. 63 5% Yageo...
PRODUCT ID: 1801
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great jack to make your own cable with....
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great jack to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 3.5mm Stereo Jack . It is free-hanging, not panel mount! It's a pretty common size and is super useful...
PRODUCT ID: 2104
This 2x8 (16 pin - 0.1" spaced) IDC Breadboard Helper is great in conjunction with any 16-pin IDC cables. It comes in two...
This 2x8 (16 pin - 0.1" spaced) IDC Breadboard Helper is great in conjunction with any 16-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...
PRODUCT ID: 1193
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of...
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat green plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...
PRODUCT ID: 4728
"Is it not a strange fate that we should suffer so much fear and doubt for so small a thing? So small a thing!!" – Boromir , The...
"Is it not a strange fate that we should suffer so much fear and doubt for so small a thing? So small a thing!!" – Boromir , The Lord of the Rings That Raspberry Pi camera or display (CSI/DSI) connectors can sometimes get damaged, and it would be a shame to have to toss the whole thing! Maybe you got a little over-enthusiastic and She-Hulk'd out on the connector arms and broke it. We understand, it happens! Here's a...
PRODUCT ID: 3983
Put your project in stealth mode with these super slim, super tiny, and silent Mini Soft Touch Push-button Switches . They're less...
Put your project in stealth mode with these super slim, super tiny, and silent Mini Soft Touch Push-button Switches . They're less 'clicky' than tactile switches, they have a rubbery elastomer that feels good to press. No dangly spider-leg-pins to solder as these buttons are SMD. We see these often in little game arcade pad layouts due to their small size and soft feel. They come in a pack of 10, and they're pretty...
PRODUCT ID: 1898
Listen up! This 1.1" (~30mm) diameter speaker is the perfect addition to any breadboard-based audio project where you need 8 Ohm impedance, and...
Listen up! This 1.1" (~30mm) diameter speaker is the perfect addition to any breadboard-based audio project where you need 8 Ohm impedance, and have 0.2W or less of power. The two pins are 15mm / 0.6" apart and fit perfectly in a breadboard or perfboard. This speaker has a durable protective plastic casing that's still lightweight. Works great with our Wave shield or class D amplifier board (just be careful not to overdrive it)
PRODUCT ID: 4182
This cable is easy to understand - you get a 3.5mm mono audio jack on one end, and two alligator clips on the other. It's also really easy to...
This cable is easy to understand - you get a 3.5mm mono audio jack on one end, and two alligator clips on the other. It's also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It's also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection. Black wire connects to sleeve, white wire connects to tip.
PRODUCT ID: 599
A mini roll of thermal paper, this fits very nicely into our mini thermal printer. 2.25" wide (about 57mm) and 50 feet long (15 meters)....
A mini roll of thermal paper, this fits very nicely into our mini thermal printer. 2.25" wide (about 57mm) and 50 feet long (15 meters). BPA-free. Perfect for use with our mini thermal printer!
PRODUCT ID: 4493
For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm...
For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching JST PH 3-Pin to Male Header Cables - 200mm, so wiring up is a cinch. Simply plug the cable in, then use the black wire to connect to your ground, white wire to the input/signal pin and the red wire to your power pin. The power pin voltage should match the voltage max of your...
PRODUCT ID: 3125
Make your own custom DE-15 cable or DE-15 interface with ease, using this DE-15 Plug to Terminal Block Breakout . You get a nice solid PCB with a...
Make your own custom DE-15 cable or DE-15 interface with ease, using this DE-15 Plug to Terminal Block Breakout . You get a nice solid PCB with a DE-15 plug and two strips of terminal blocks that you can use with stranded or solid core wire to quickly assemble your own wiring jigs. If you just need a plain DE-15 / VGA cable, we have plenty and it's less expensive to just buy a standard cable than DIY it. We recommend this adapter when you...
PRODUCT ID: 3877
Sometimes you feel low, and sometimes you feel high - cause your logic levels are opposite what they should be! But this easy-to-use inverter chip...
Sometimes you feel low, and sometimes you feel high - cause your logic levels are opposite what they should be! But this easy-to-use inverter chip will flip that frown upside-down. This chip is spec'd to run at 5V but we've run it at 3V just fine. Power it by connecting up GND and VCC to your desired output logic level. High-level inputs can be as low as 2V and the output will be inverted on each of the 6 pairs of inverters. It's...
PRODUCT ID: 3694
These Banana Plugs not only look great, they're also solder-free and stackable ! Banana plugs are often used on test equipment, tools,...
These Banana Plugs not only look great, they're also solder-free and stackable ! Banana plugs are often used on test equipment, tools, synthesizers and other electronic patch panels. Each connector is designed with bowed strips to provide secure and uniform contact between the plug and jack. Even after multiple insertions, the non-collapsing design stays true to form. The plug springs are nickel-plated Beryllium copper and will...
PRODUCT ID: 1333
This membrane keypad has a single key, but it does have an embedded surface-mount red LED installed. The flex cable is also extra-long, so we can...
This membrane keypad has a single key, but it does have an embedded surface-mount red LED installed. The flex cable is also extra-long, so we can think of a lot of wearable and portable projects that would use this sort of switch and have an LED as feedback (say, to indicate that an action is occuring or the power is on). Since the keypad is soft plastic, it can be sewn with needle and thread. The back of the pad has a removable paper cover that...
PRODUCT ID: 4190
We've got plenty of round and square buttons, but these LED Illuminated Triangle Pushbuttons are welcome to the party. These make us...
We've got plenty of round and square buttons, but these LED Illuminated Triangle Pushbuttons are welcome to the party. These make us think of 1960's or 70's Sci-Fi control board buttons. As everyone knows, triangular buttons are the most retro-futuristic of all button shapes. Get 6 of them together for a cool hexagonal arrangement, or just have one triangle at a time. These buttons are medium-sized, large...
PRODUCT ID: 808
When you need to amplify, filter, add, or otherwise manipulate analog signals you'll certainly want an operational amplifier at your side. This...
When you need to amplify, filter, add, or otherwise manipulate analog signals you'll certainly want an operational amplifier at your side. This is our favorite hobby op-amp, which we use in our kits! It's DIP package so very easy to work with on a breadboard or perfboard. It has two amplifiers inside. It can run from voltages as low as 2.7V and up to 6V. It has rail to rail input and output, which is a common problem for beginners who...
PRODUCT ID: 4211
If you need to add a panel-mount connection for USB Mini B, but don't have the time or tools to cut a custom oval or square hole, this ...
If you need to add a panel-mount connection for USB Mini B, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da!...
PRODUCT ID: 2139
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact...
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1" terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks...
PRODUCT ID: 475
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED...
PRODUCT ID: 1490
Super-tall clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a...
Super-tall clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. These are extra tall which are useful when putting your project in an enclosure and you want the buttons to stick out. They come in a pack of 10,...
PRODUCT ID: 3670
High-conductive heating fabrics are so hot right now! Literally! This non-woven fabric feels a little like felted paper but is filled with conductive...
High-conductive heating fabrics are so hot right now! Literally! This non-woven fabric feels a little like felted paper but is filled with conductive material that can make the fabric emit heat when powered. Resistive heating fabrics safely deliver comfortable conductive and radiant heating at low voltage through thin, lightweight and flexible fabric. Unlike conventional resistive wire heaters, the whole surface of the fabric is...
PRODUCT ID: 1800
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with....
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 3.5mm Stereo Plug. It's a pretty common size and is super useful in most headphones or basic audio...
PRODUCT ID: 4392
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the...
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the horizontal style. You can use these with any of our JST PH 4 / STEMMA cables. They're not STEMMA QT compatible (those use the smaller JST SH). However, you can fit Seeed Grove connectors into JST PH which is pretty handy. We also carry these connectors...
PRODUCT ID: 3647
Get a precision fit with these lovely machined 'Swiss pin' headers. In this world nothing can be said to be certain, except we need headers,...
Get a precision fit with these lovely machined 'Swiss pin' headers. In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains five 36-pin male plug headers, standard 0.1" pitch. We also stock its female socket counterpart that these fit with. You cannot use regular stamped-metal headers with swiss pin as they will not fit Female headers are like the duct tape of...
PRODUCT ID: 450
Add lots more outputs to a microcontroller system with chainable shift registers. These chips take a serial input (SPI) of 1 byte (8 bits) and then...
Add lots more outputs to a microcontroller system with chainable shift registers. These chips take a serial input (SPI) of 1 byte (8 bits) and then output those digital bits onto 8 pins. You can chain them together so putting three in a row with the serial output of one plugged into the serial input of another to make 3 x 8 = 24 digital outputs. You can chain pretty much as many as you want. This makes it easy to control a lot of outputs like...
PRODUCT ID: 2105
This little 2x3 (6 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with our 6-pin IDC cable. It comes in...
This little 2x3 (6 pin - 0.1 spaced) IDC Breadboard Helper is great in conjunction with our 6-pin IDC cable. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket. Since IDC cables are so standard, but a royal pain to use with breadboards, this is a good and cheap hack for...
PRODUCT ID: 4727
This socket is good for any SOIC/SOP Wide - body 16 pin chip in a 300mil wide body. Simply flip open the latch, insert the chip, and flip down the...
This socket is good for any SOIC/SOP Wide - body 16 pin chip in a 300mil wide body. Simply flip open the latch, insert the chip, and flip down the latch to secure it in place. The chip is held securely against gold 'fingers' (no, stop, Mr. Bond! It's not that Goldfinger!) in the socket. The bottom footprint matches the same SOIC footprint so you can solder this onto an existing PCB as long as you have the clearance for...
PRODUCT ID: 3643
This brilliant invention is a blessing for makers designing or using boards with standard 2.1mm DC barrel jacks. Many devices opt against a proper...
This brilliant invention is a blessing for makers designing or using boards with standard 2.1mm DC barrel jacks. Many devices opt against a proper power switch, for size or cost or other design reasons. So, you're expected to unplug when not in use. But you want something a little fancier! This 2.1mm DC Power Jack with Rocker Switch has the same PCB layout as classic non-switched jacks but has a li'l extra on top - a labeled slide...
PRODUCT ID: 4207
These brilliant solder-able standoffs will make your mechanical PCB mounting problems go away. They're super simple - round M3 standoffs that are...
These brilliant solder-able standoffs will make your mechanical PCB mounting problems go away. They're super simple - round M3 standoffs that are coated with tin so you can solder them in an oven or with a very powerful soldering iron & some patience. All you have to do is put a 4.25mm hole with 6.2mm solder ring on your PCB, then this components snout goes into the PCB, and solder it in place. The part is incredibly strong and saves you...
PRODUCT ID: 3308
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic clear protective casing, and a diffused...
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic clear protective casing, and a diffused white LED at the tip of the switch, this Clear/White LED Toggle Switch is sure to add some flair (and flare!) to your project. Often seen on control panels, now you can mimic a racing car, fighter jet, submarine status panel, factory controls, or anything really. They will control...
PRODUCT ID: 2135
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact...
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1" terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks...
PRODUCT ID: 1444
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large...
A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button...
PRODUCT ID: 1190
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of...
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat red plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has...
PRODUCT ID: 3835
Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.187"...
Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.187" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this off if there's no use for it. If you need a...
PRODUCT ID: 457
Add a bunch of high-power outputs to a microcontroller system with chainable shift registers. These chips take a serial input (SPI) of 1 byte (8...
Add a bunch of high-power outputs to a microcontroller system with chainable shift registers. These chips take a serial input (SPI) of 1 byte (8 bits) and then output those digital bits onto 8 pins. You can chain them together so putting three in a row with the serial output of one plugged into the serial input of another to make 3 x 8 = 24 digital outputs. You can chain pretty much as many as you want. This makes it easy to control a lot of...
PRODUCT ID: 3663
If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni...
If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and whammo! Your header is securely attached to your Pi Zero or pHAT/bonnet/HAT. Make sure to carefully read Pimoroni's guide for fitting hammer headers. These...
PRODUCT ID: 3347
Add some steely elegance to your project with these Metal Ball Tactile Buttons . They've got a nice industrial shine to them along with a...
Add some steely elegance to your project with these Metal Ball Tactile Buttons . They've got a nice industrial shine to them along with a light blue underbelly. Not only do they look good, but they're also good if you have an actuator that will be pressing the button at an angle! Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard...
PRODUCT ID: 473
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED...
PRODUCT ID: 970
Bring in some muscle to your output pins with 8 mighty Darlingtons! This DIP chip contains 8 drivers that can sink 500mA from a 50V supply and has...
Bring in some muscle to your output pins with 8 mighty Darlingtons! This DIP chip contains 8 drivers that can sink 500mA from a 50V supply and has kickback diodes included inside for driving coils. This will let your little microcontroller or microcomputer power solenoids, DC motors (in one direction) and unipolar stepper motors. Please note, this is an 'open collector' driver - it can only be used to connect the load to ground and there...
PRODUCT ID: 3103
Sometimes a simple analog control device can be the perfect tactile solution for your project, but they can be surprisingly hard to come by. Luckily...
Sometimes a simple analog control device can be the perfect tactile solution for your project, but they can be surprisingly hard to come by. Luckily we've found a low cost, quality PSP 3000 2-Axis Analog Thumb Joystick to fulfill your directional analog input needs! This is a replacement component for the PSP 3000, but we think they'd make for a great little joystick/thumbstick add-on for a wearable, or portable project. It's similar to...
PRODUCT ID: 2225
This is just a standard USB-A jack. It's a sturdy metal with 4 pins in the back and 2 small mounting tabs that make it easy to use in your...
This is just a standard USB-A jack. It's a sturdy metal with 4 pins in the back and 2 small mounting tabs that make it easy to use in your next USB project We use this USB-A jack for everything, really. With a little effort you can bend the side mounting tabs and solder the 4 data/power pins into a Perma Proto. Its not good for solderless breadboards, the pins are not very long.
PRODUCT ID: 3642
This brilliant invention is a blessing for makers designing or using boards with standard 2.1mm DC barrel jacks. Many devices opt against a proper...
This brilliant invention is a blessing for makers designing or using boards with standard 2.1mm DC barrel jacks. Many devices opt against a proper power switch, for size or cost or other design reasons. So, you're expected to unplug when not in use. But you want something a little fancier! This 2.1mm DC Power Jack with Slide Switch has the same PCB layout as classic non-switched jacks but has a li'l extra on top - a labeled slide switch!...
PRODUCT ID: 3008
In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains five 36-pin short...
In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains five 36-pin short female headers, 0.1" pitch. These headers are very short for fitting into tight spaces with a height of just 5mm instead of the 'standard' 8mm. Female headers are like the duct tape of electronics. They're great for connecting things together, soldering to perf-boards, sockets for...
PRODUCT ID: 677
Connect this to that without soldering using these quick terminal blocks. They allow connecting of two sets of four wires together using just a...
Connect this to that without soldering using these quick terminal blocks. They allow connecting of two sets of four wires together using just a flat-head screwdriver. These are UL rated to carry up to 15 Amps, so they're great for high current LED strips! Can be used with wires from 14AWG to 22 AWG
PRODUCT ID: 4536
As technology changes and adapts, so does Adafruit, and speaking of adapting , this adapter has a 2.1mm barrel jack socket and a...
As technology changes and adapts, so does Adafruit, and speaking of adapting , this adapter has a 2.1mm barrel jack socket and a USB C plug - you could use this to power a USB C device from a common wall adapter. USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. Plug this adapter onto the end of a 2.1mm 5VDC barrel...
PRODUCT ID: 4792
If you want to do more with the BBC micro:bit, getting those pins from the card-edge connector is going to be your first hurdle. Unlike many...
If you want to do more with the BBC micro:bit, getting those pins from the card-edge connector is going to be your first hurdle. Unlike many dev-boards, the micro:bit isn't breadboard-friendly. That makes the 'bit durable and easy to manufacture but means you need a special connector. This surface-mount edge connector is very slim and fully SMT, so it's a breeze to automate. It also only has contacts on one side, just like the...
PRODUCT ID: 2141
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact...
After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1" terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks...
PRODUCT ID: 4228
These Reese's Piece's lookin' bits fit perfectly on top of tactile buttons with 2.4mm square tops and give a satisfying 8mm diameter...
These Reese's Piece's lookin' bits fit perfectly on top of tactile buttons with 2.4mm square tops and give a satisfying 8mm diameter surface area for your fingers to press. You get 10 candy-colored round caps. You get two of each color: red, yellow, white, gray , and Adafruit black . Snap these onto a tactile switch body (not included) to customize your PyGamer, or anything else with 2.4mm-square-top tactile switches.
PRODUCT ID: 3838
Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.25"...
Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.25" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this off if there's no use for it. If you need a...
PRODUCT ID: 1191
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of...
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat yellow plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...
PRODUCT ID: 1798
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with....
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio cable that can rival the best! This item is a 2.5mm Stereo Plug - it is a less common size than a stereo 3.5mm standard headphone jack but is still just...
PRODUCT ID: 4395
Stop fiddling with micro SD card sockets in the back of your latest gadget during development, and give yourself a little more elbow room with...
Stop fiddling with micro SD card sockets in the back of your latest gadget during development, and give yourself a little more elbow room with this Small Micro SD Card Extender . This is a great hack for length constraints with 3D printers, single-board computers, data-logging kits and more. Get to your micro SD card in and out without using your fingernails! Insert the micro SD card in the little tray, and gently press the other end...
PRODUCT ID: 2783
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This...
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 4.7K Ω Resistors. More specifically, they are carbon film , through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistors. Whew! These are super common and great for use in any kit, breadboard, perf-board, or other project. We got ones with...
PRODUCT ID: 3330
What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a...
What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a LCD Controllable Black-out Panel)! They're often used for electric welding helmets because they can protect the welder's eyes from the bright sparks. Or – if you aren't a welder – they can be used to provide a "reveal" effect for your...
PRODUCT ID: 4510
Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Spring Block Adapter . You get a nice solid PCB...
Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Spring Block Adapter . You get a nice solid PCB with a DE-9 socket and one line of push-terminal blocks. Just flick up the little levers and slide in your stranded or solid core wire to quickly assemble your own wiring jigs. No soldering required! Perfect for when you need a non-standard wiring setup or interfacing to an older device with one of...
PRODUCT ID: 1084
Click click click - oh pardon me I was having fun clicking away on my mechanical decade counters. Each order comes with five individual counters....
Click click click - oh pardon me I was having fun clicking away on my mechanical decade counters. Each order comes with five individual counters. They're snap together so you can connect as many or as few as you'd like. Each one has two buttons - an up counter and down counter. Once you get to 9 it circles back to zero. On the back is a PCB with 11 contacts - one common and then 10 that are shorted to the common one by one as the counter...
PRODUCT ID: 3306
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic blue protective casing, and a diffused blue...
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic blue protective casing, and a diffused blue LED at the tip of the switch, this Blue LED Toggle Switch is sure to add some flair (and flare!) to your project. Often seen on control panels, now you can mimic a racing car, fighter jet, submarine status panel, factory controls, or anything really. They will control virtually any...
PRODUCT ID: 1641
You have some electrons over here, and you want them over there but you don't want the electrons from over there to be able to come over here?...
You have some electrons over here, and you want them over there but you don't want the electrons from over there to be able to come over here? That's what a diode is for, these are directional current valves and have the benefit of being waaay smaller than vacuum tubes. Classic 1N4148's are great for any kind of small signal (not power!) rectification. Use them all the time, so they come in a pack of 10. Check the datasheet for more...
PRODUCT ID: 1540
Breakaway header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards, fits into any breadboard,...
Breakaway header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards, fits into any breadboard, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of ten! Each pack contains 10 x single row, right angle male 1x36-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1" grid and broken apart easily with pliers or...
PRODUCT ID: 1094
Use this nice fixed laser mount to attach any of our laser diode modules to your desk, robot, shark, etc. A set-screw holds the laser in place. Has a...
Use this nice fixed laser mount to attach any of our laser diode modules to your desk, robot, shark, etc. A set-screw holds the laser in place. Has a flat mounting plate with four holes for easy attachment and adjustment. Fits all of our modules. Laser not included
PRODUCT ID: 4214
If you need to add a panel-mount connection for Micro USB, but don't have the time or ability to cut a custom oval or square hole, this USB A...
If you need to add a panel-mount connection for Micro USB, but don't have the time or ability to cut a custom oval or square hole, this USB A Jack to Micro USB B Jack Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut,...
PRODUCT ID: 3481
This potentiometer is a two-in-one: it's a log taper 10K ohm potentiometer , with a grippy shaft an d it comes with an on-off switch . It's...
This potentiometer is a two-in-one: it's a log taper 10K ohm potentiometer , with a grippy shaft an d it comes with an on-off switch . It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2" apart with pin-points, so you can plug it into a perfboard. Note the spacing on the switch/pot pins is 0.2" so it wont work in a solderless breadboard as nicely, unless you...
PRODUCT ID: 4129
If you need to add a panel-mount connection for HDMI, but don't have the time or ability to cut a custom oval or square hole, this HDMI Round...
If you need to add a panel-mount connection for HDMI, but don't have the time or ability to cut a custom oval or square hole, this HDMI Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing HDMI kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach....
PRODUCT ID: 1189
OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a...
OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying "beep!". We've seen these on some games of skill in arcades, they're easy to mount on...
PRODUCT ID: 476
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common...
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED...
PRODUCT ID: 804
Although you may not see PS/2 keyboards & mice as often on desktop computers, there's still tons of them out there, and they're really...
Although you may not see PS/2 keyboards & mice as often on desktop computers, there's still tons of them out there, and they're really easy to interface to a microcontroller. PS/2 devices are powered by 5V and use two data pins to communicate back and forth. There's tons of example code out there for every kind of microcontoller (including Arduinos) for keyboard and mouse interfacing. So all you need to do is connect from the...
PRODUCT ID: 1194
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of...
BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a flat blue plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED...
PRODUCT ID: 1331
Keep it cool with a Peltier module. These unique electronic components can generate a temperature differential when powered. That is to say, apply 5V...
Keep it cool with a Peltier module. These unique electronic components can generate a temperature differential when powered. That is to say, apply 5V to the red (positive) and black (negative) wires and one side will get cold while the other side gets hot. For best results, you'll need to wick away that heat (otherwise the cold side will slowly get warmer). A fan and/or heatsink is ideal. This module is a 5V module, and is rated for 5W max...
PRODUCT ID: 1732
Listen up! This high power 4" diameter speaker will amp up any audio project where you need loud sound! It is 4 ohm impedance, rated for 20W...
Listen up! This high power 4" diameter speaker will amp up any audio project where you need loud sound! It is 4 ohm impedance, rated for 20W continuous power. (This thing is really loud) It also has four handy mounting tabs 3 inches apart, and a grill that fits on top. The grill is to protect the cones, and is not necessary for use. This speaker has a nice wide range of 60Hz - 24kHz, which is pretty good for a speaker this large. Originally...
PRODUCT ID: 3219
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic yellow protective casing, and a yellow LED...
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic yellow protective casing, and a yellow LED at the tip of the switch, this Yellow LED Toggle Switch is sure to add some flair (and flare!) to your project. Often seen on control panels, now you can mimic a racing car, fighter jet, submarine status panel, factory controls, or anything really. They will control virtually any...
PRODUCT ID: 1542
Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow...
Socket (female) header is like the duct tape of electronics. Its great for connecting things together, soldering to perf-boards or PCBs to allow 22AWG wire or male header to connect, etc. We go through these gals real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains 5 x right angle female 36-pin long headers, 0.1" pitch, that can be stacked next to each other on a 0.1" grid. They aren't...
PRODUCT ID: 3394
This Panel Mount 10K Dual Log Potentiometer is a dual-ganged potentiometer that will satisfy all your stereo-signal needs. Instead of just one...
This Panel Mount 10K Dual Log Potentiometer is a dual-ganged potentiometer that will satisfy all your stereo-signal needs. Instead of just one potentiometer, you actually get two separate pots, 'ganged' together. Turning the grippy shaft twists both standard logarithmic-taper 10Kohm potentiometers. It's smooth and easy to turn, but not so loose that it will shift on its own. We also offer this potentiometer in a singular...
PRODUCT ID: 4328
If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST...
If you're a DIY enthusiast who likes to micro -manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. These connectors can be used with Qwiic boards and cables to easily connect sensors and drivers from one...
PRODUCT ID: 1363
Add some extra boom to your audio project with these powered loudspeakers. We sampled half a dozen different models to find ones with a good...
Add some extra boom to your audio project with these powered loudspeakers. We sampled half a dozen different models to find ones with a good frequency response, so you'll get quality audio output for music playback. Simply connect the standard 3.5mm stereo plug into your Raspberry Pi model B or B+, Wave shield, etc. There's even a volume control wheel on it so you can set it up just right. For power, plug the USB connector into anything...
PRODUCT ID: 1335
This is for people who just want to get cold fast. The 12V Peltier module is mounted onto a 12V heatsink and fan assembly with thermal paste and an...
This is for people who just want to get cold fast. The 12V Peltier module is mounted onto a 12V heatsink and fan assembly with thermal paste and an aluminum clamp. Simply connect to 12V 5A+ power supply and you will see frost appear on the aluminum plate within a minute. This assembly comes with the best Peltier we could get, so it can get even colder than the stand-alone module we stock, but we think the price is worth it. Just sitting on our...
PRODUCT ID: 1794
When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking)...
When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220s, but because of the very low Rds(on) of down to 70 mOhms (depending on the Vgs - check the datasheet) you can get away with no heatsinking for pretty high loads! The threshhold voltage is up...