Hats

Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2/3/Pi 4 - Mini Kit

PRODUCT ID: 2324

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate...

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model Pi 3, Pi Zero, A+, B+, or Pi 2, 3, & 4 Here's the low-down on the GPS module: -165 dBm sensitivity, 10 Hz updates, 66 channelsOnly 20mA current drawBuilt in Real Time Clock (RTC) - slot in a CR1220 backup...

NOTIFY ME

$44.95

OUT OF STOCK

Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

PRODUCT ID: 2327

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. For use...

NOTIFY ME

$17.50

OUT OF STOCK

Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

PRODUCT ID: 2348

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it...

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Raspberry Pi and motors are not included. Works with any and all Raspberry Pi computers with 2x20 connection port. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip ...

NOTIFY ME

$22.50

OUT OF STOCK

Adafruit PiTFT 2.2" HAT Mini Kit - 320x240 2.2" TFT - No Touch

PRODUCT ID: 2315

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240...

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top of your Model A+ or B+ and fits into our case quite nicely. It's designed to plug directly onto the...

$24.95

27 IN STOCK

Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit

PRODUCT ID: 2345

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2/3/ or Pi 4 with the Adafruit RGB Matrix HAT. This HAT plugs into...

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2/3/ or Pi 4 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. This HAT is our finest to date, full of some really great circuitry. Let me break it down for you: Simple design - plug in power, plug...

NOTIFY ME

$24.95

OUT OF STOCK

Adafruit Perma-Proto HAT for Pi Mini Kit - No EEPROM

PRODUCT ID: 2310

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector)...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to...

$4.95

IN STOCK

Adafruit PiTFT 2.4" HAT Mini Kit - 320x240 TFT Touchscreen

PRODUCT ID: 2455

Is this not the cutest little display for the Raspberry Pi? It features a 2.4" display with 320x240 16-bit color pixels and a resistive touch...

Is this not the cutest little display for the Raspberry Pi? It features a 2.4" display with 320x240 16-bit color pixels and a resistive touch overlay. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! It's designed to fit nicely onto the Pi Model Zero, A+, B+, Pi 2, Pi 3 - any Pi with a 2x20 connector. This...

$34.95

26 IN STOCK

Adafruit Capacitive Touch HAT for Raspberry Pi - Mini Kit - MPR121

PRODUCT ID: 2340

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing...

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like touch-reactive tablets and phones, as well as control panels for appliances, which is where you may have used it before. This HAT allows you to create electronics that can...

$14.95

IN STOCK

Adafruit Perma-Proto HAT for Pi Mini Kit - With EEPROM

PRODUCT ID: 2314

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with which...

$7.50

IN STOCK

Pimoroni Unicorn Hat - 8x8 RGB LED Shield for Raspberry Pi A+/B+

PRODUCT ID: 2288

Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi....

Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi. Unicorn HAT provides a wash of controllable color that is ideal for mood-lighting, 8x8 pixel art, persistence of vision effects, status indications, or just blasting colour into your surroundings. 64 RGB LEDs (WS2812B) each wtih 24-bit RGB colorPython API (NeoPixel compatible!)EEPROM with...

$29.95

8 IN STOCK

Brass M2.5 Standoffs for Pi HATs - Black Plated - Pack of 2

PRODUCT ID: 2336

"These go to eleven." 11 millimeters that is! Our Black Plated M/F Brass Standoffs are engineered specifically...

"These go to eleven." 11 millimeters that is! Our Black Plated M/F Brass Standoffs are engineered specifically to keep your Pi HAT snug on your Pi while also keeping the two boards separated, in particular the HDMI port. These standoffs can also be screwed into each other allowing stacking multiple HATs on to one Pi! They're the perfect companion for any Pi Hat combo. Each order comes with two...

NOTIFY ME

$0.75

OUT OF STOCK

Pimoroni Skywriter HAT - 3D Gesture Sensor for Raspberry Pi

PRODUCT ID: 2325

Control your Raspberry Pi 3, 2, A+, B+, or Zero with a flick of the wrist! The Pimoroni Skywriter HAT senses the position...

Control your Raspberry Pi 3, 2, A+, B+, or Zero with a flick of the wrist! The Pimoroni Skywriter HAT senses the position of your fingers in the air above. Using Pimoroni's Python API you can read off the positional data (x, y, z) and common gestures like flick left, tap, and double tap. Electrical near-field 3D/gesture sensing4-layer PCB for best sensing performanceSenses from up to 5cm awayFull 3D position data...

$20.95

34 IN STOCK

Pimoroni Explorer HAT Pro for Raspberry Pi

PRODUCT ID: 2427

The Explorer HAT Pro is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer Pro from Pimoroni there are a heap of...

The Explorer HAT Pro is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer Pro from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features : 4x buffered 5V tolerant inputs Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V...

$22.95

78 IN STOCK

Brass M2.5 Standoffs 16mm tall - Black Plated - Pack of 2

PRODUCT ID: 2337

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered...

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories with extra tall headers properly secured while also keeping the two boards separated. These standoffs can also be screwed into each other just like the 11mm versions (made for PiHATs). Each order comes with two standoffs and two hex...

$1.25

41 IN STOCK

SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header

PRODUCT ID: 2187

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's...

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's harder to use than the Thru-Hole type headers, but for the slickest, slimmest fit, this header is recommended!

$1.95

IN STOCK

Raspberry Pi Sense HAT - For the Pi 3 / 2 / B+ / A+

PRODUCT ID: 2738

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT ! The Raspberry Pi Sense HAT is...

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT ! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘Astro Pi’. The Sense HAT has several integrated circuit based sensors can be used for many different types of experiments, applications, and even games. And it's being used in conjunction with the Raspberry Pi Foundation...

$39.95

26 IN STOCK

Pimoroni Piano HAT

PRODUCT ID: 2695

Raspberry Pi - meet your new musical B.F.F! With the Pimoroni Piano HAT you can control hardware synthesizers and software...

Raspberry Pi - meet your new musical B.F.F! With the Pimoroni Piano HAT you can control hardware synthesizers and software synths or play some really beautiful music in Python. Surprise everyone with your creativity, maybe even yourself! This HAT comes with 16 touch sensitive buttons, up and down octave controls, and 13 piano keys from C to shining C! Each button on Piano HAT can be...

$19.95

6 IN STOCK

Pi-EzConnect Terminal Block Breakout HAT

PRODUCT ID: 2711

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has...

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry PiMini proto area for adding componentsAdd standard male or female headers for breadboard like functionalityPower (both 5V and 3.3V) as well as ground connections...

$19.95

53 IN STOCK

Raspberry Pi PoE Hat

PRODUCT ID: 3953

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible with Raspberry Pi 3 B+ that has PoE pins and Raspberry Pi 4. For people with neither Pi 3 B+'s...

NOTIFY ME

$20.00

OUT OF STOCK

Adafruit DC & Stepper Motor Bonnet for Raspberry Pi

PRODUCT ID: 4280

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as...

Let your robotic dreams come true with the new DC+Stepper Motor Bonnet from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. We basically took our super-popular DC+Stepper Motor HAT and squeezed it down and made it fully assembled - plug and play ready to go, no soldering required! Raspberry Pi and motors are not included. Works with any and all...

$22.50

10 IN STOCK

SparkFun Qwiic / STEMMA QT HAT for Raspberry Pi

PRODUCT ID: 4688

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter SparkFun’s Qwiic / STEMMA QT ecosystem when using...

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter SparkFun’s Qwiic / STEMMA QT ecosystem when using that Raspberry Pi that you’ve come to know and love. The Qwiic HAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic connectors on the HAT. Since the Qwiic system allows for daisy-chaining boards with different addresses, you can stack as many sensors as...

$7.50

6 IN STOCK

Pimoroni Unicorn HAT Mini for Raspberry Pi - PIM498

PRODUCT ID: 4637

Over one hundred RGB LEDs, all individually-controllable, and four tactile buttons. It's the ultimate pocket-sized rainbow generator for...

Over one hundred RGB LEDs, all individually-controllable, and four tactile buttons. It's the ultimate pocket-sized rainbow generator for Raspberry Pi! Unicorn HAT Mini is a 17x7 matrix of RGB LEDs that can be controlled, both in terms of color and brightness, to display animations, text, simple images, and more. The four tactile buttons add tonnes of utility to control the color or brightness of the LEDs, or as...

NOTIFY ME

$22.95

OUT OF STOCK

Pimoroni Enviro – Indoor Environmental Monitor for RaspPi - PIM486

PRODUCT ID: 4455

Monitor your world with Pimoroni's Enviro PHAT for Raspberry Pi! There are a whole bunch of fancy environmental sensors on...

Monitor your world with Pimoroni's Enviro PHAT for Raspberry Pi! There are a whole bunch of fancy environmental sensors on these boards, and a gorgeous little full-color LCD to display your data. It's the perfect way to get started with citizen science and environmental monitoring - with a great UI and easy-to-use Python code Enviro is designed for indoor monitoring, letting you measure temperature, pressure, humidity,...

$34.95

39 IN STOCK

Pimoroni Automation HAT for Raspberry Pi

PRODUCT ID: 3289

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Take control of and...

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Take control of and monitor your world with Pimoroni's Automation HAT -- an ultimate jack-of-all-trades Raspberry Pi HAT! With relays, analog channels, powered outputs, and buffered inputs (all 24V tolerant), this home monitoring and automation controller allows you to hook up a plethora of goodies to...

$29.95

58 IN STOCK

Pimoroni Pico HAT Hacker

PRODUCT ID: 3577

Pimoroni's Pico HAT Hacker gives you full access to all 40 pins on your Pi, broken out at the top. It's a super-skinny 0.8mm PCB, so you can...

Pimoroni's Pico HAT Hacker gives you full access to all 40 pins on your Pi, broken out at the top. It's a super-skinny 0.8mm PCB, so you can solder it right onto the pins on your Pi and still have enough height on a standard header to fit a HAT or pHAT on top. There are handy labels for all of the pins, with BCM pin numbering on one side, and more descriptive labels on the other to show where the I2C, UART, SPI, PWM, and I2S pins...

$2.95

IN STOCK

Pimoroni Pirate Audio: 3.5mm Line-out for Raspberry Pi

PRODUCT ID: 4452

Plug Pirate Audio Line-out for Raspberry Pi into your hi-fi amp or powered speakers, then sit back, relax, and soak in the rich, digital...

Plug Pirate Audio Line-out for Raspberry Pi into your hi-fi amp or powered speakers, then sit back, relax, and soak in the rich, digital audio. It has a high-quality I2S DAC, high-res color display, and squishy playback control buttons. This board is perfect for upgrading an existing hi-fi amp and speakers, or a set of powered monitors, with digital audio from local audio files (MP3, FLAC, etc.) or from streaming...

$24.95

2 IN STOCK

Pimoroni Inky pHAT for Raspberry Pi - 3 Color eInk Display

PRODUCT ID: 3743

Here at Adafruit we never tire of cool, new displays, so these super sweet tri-color e-paper displays really caught our eye! Pimoroni's Inky pHat...

Here at Adafruit we never tire of cool, new displays, so these super sweet tri-color e-paper displays really caught our eye! Pimoroni's Inky pHat is a petite 212x104 pixel three-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the 3-second display-change-cycle....

$26.50

19 IN STOCK

Pimoroni Pan-Tilt HAT for Raspberry Pi - without pan-tilt module

PRODUCT ID: 3353

The Pan-Tilt HAT from Pimoroni lets you mount and control a pan-tilt module right on top of your Raspberry Pi. The HAT and its on-board...

The Pan-Tilt HAT from Pimoroni lets you mount and control a pan-tilt module right on top of your Raspberry Pi. The HAT and its on-board microcontroller let you independently drive the two servos (pan and tilt), as well as driving up to 24 regular LED (with PWM control) or NeoPixel RGB (or RGBW) LEDs. There's also a handy slot through which you can route the servo, LED, and camera cables. The module pans and tilts through 180...

$14.95

25 IN STOCK

Pimoroni Unicorn HAT HD

PRODUCT ID: 3580

Unicorn HAT HD crams 256 RGB LEDs, in a 16x16 = 256 LED matrix, onto a single HAT. High-definition rainbow goodness! You can still use it for all of...

Unicorn HAT HD crams 256 RGB LEDs, in a 16x16 = 256 LED matrix, onto a single HAT. High-definition rainbow goodness! You can still use it for all of the same things as the regular Unicorn HAT, but with four times as many pixels it makes much more complex animations possible, including scrolling text, and even low resolution videos. The bundled ninja diffuser makes the pixels look extra shiny by providing some subtle diffusion, blurring the...

$34.95

10 IN STOCK

Pimoroni Inky pHAT - 3 Color eInk Display - Yellow/Black/White

PRODUCT ID: 3933

What's that, you say? Pimoroni has another new super sweet tri-color e-paper display? Oh feast your eyes! This Inky pHat...

What's that, you say? Pimoroni has another new super sweet tri-color e-paper display? Oh feast your eyes! This Inky pHat in Yellow/Black/White is a petite 212x104 pixel three-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the...

$26.50

3 IN STOCK

Pimoroni Touch pHAT for Raspberry Pi Zero

PRODUCT ID: 3472

The Pimoroni Touch pHAT has six capacitive touch buttons, each with a bright white LED, so you can add a touch interface to your Raspberry Pi. While...

The Pimoroni Touch pHAT has six capacitive touch buttons, each with a bright white LED, so you can add a touch interface to your Raspberry Pi. While it is shaped and sized to match a Pi Zero, it works great with any Pi with 2x20 connector. You can even use a dry erase pen to write on the pads to label their function. The pHAT features a CAP1166 capacitive touch and LED driver chip that is read over I2C. Each pad has a matching LED that can be...

$8.50

77 IN STOCK

Pirate Audio: Speaker for Raspberry Pi - Built-in 1W Speaker

PRODUCT ID: 4451

Pimoroni's Pirate Audio Speaker is perfect for making a Lilliputian radio, sound effect player, or even as a teeny-weeny games...

Pimoroni's Pirate Audio Speaker is perfect for making a Lilliputian radio, sound effect player, or even as a teeny-weeny games console. The built-in 1W speaker may not be the loudest, but it's great fun for lots of projects. The display and playback squishy buttons let you control your audio or sound effects. Use the Pirate Audio software to play local audio files (MP3, FLAC, etc) or stream from services like Spotify....

$24.95

57 IN STOCK

Pi Supply PaPiRus Zero ePaper/eInk pHAT v1.2

PRODUCT ID: 3335

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero...

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero mini computer. ePaper / eInk is a display technology that mimics the appearance of ink on normal paper. Unlike conventional displays, ePaper reflects light – just like ordinary paper – and is capable of holding text and images indefinitely, even without electricity. Because of this,...

$34.95

28 IN STOCK

Pimoroni Pirate Audio: Headphone Amp for Raspberry Pi - PIM482

PRODUCT ID: 4454

Build your own home-brew iPod with Pimoroni' s Pirate Audio Headphone Amp ! It's an all-in-one solution, with gorgeous album art...

Build your own home-brew iPod with Pimoroni' s Pirate Audio Headphone Amp ! It's an all-in-one solution, with gorgeous album art display, track info, and playback controls, for playing your local audio files (MP3, FLAC, etc) or streaming music from Spotify. The DAC and headphone amp give you crisp digital amplified audio through your wired headphones. Pirate Audio is a range of all-in-one audio boards for...

$24.95

36 IN STOCK

Pirate Audio: 3W Stereo Speaker Amp for Raspberry Pi

PRODUCT ID: 4453

Bring your speaker set into the 21st century with Pirate Audio 3W Stereo Amp for Raspberry Pi ! Get punchy digital audio through the...

Bring your speaker set into the 21st century with Pirate Audio 3W Stereo Amp for Raspberry Pi ! Get punchy digital audio through the push-fit terminals and control your music with the built-in color LCD and squishy playback control buttons. The push-fit connectors on Pirate Audio 3W Stereo Amp make it super-simple to connect up a set of speakers, whether they're bookshelf or floor-standing speakers, or the speakers in an...

$24.95

3 IN STOCK

Pimoroni Picade X HAT USB-C for Raspberry Pi - PIM462

PRODUCT ID: 3402

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT . It's the best, easiest way to make a...

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT . It's the best, easiest way to make a super-sweet arcade system using any Raspberry Pi. Simply pop it onto your Pi, plug your Pi power supply into the USB-C connector on the Picade HAT (it back-powers your Pi through the GPIO, so no need for a separate power supply), wire up your controls to the terminal blocks,...

$19.95

4 IN STOCK

Pimoroni Mini Black HAT Hack3r - Fully Assembled

PRODUCT ID: 3182

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT or pHAT on your...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT or pHAT on your Raspberry Pi Model Zero, 3, 2, A+, or B+ (any Pi with a 2x20 connector). The Pimoroni Mini Black HAT Hack3r is ideal for debugging your (p)HAT projects or combining a (p)HAT with other circuits. Features: HAT & pHAT spec landing area with PCB standoffsIncludes 40 pin GPIO ribbon cableAll GPIO pins...

$14.95

10 IN STOCK

8 Channel LoRa Gateway HAT with LoRa and GPS Antenna - SX1301 - Pi Not Included

PRODUCT ID: 4284

If you're building a Raspberry Pi project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most...

If you're building a Raspberry Pi project and need to send data back-and-forth, the WiFi module built into newer Pi's should be fine for most cases. However , WiFi does not have a long range and also requires both investment (through your ISP) and setup (routers, access points, network security schemes). If you're deploying your project somewhere more remotely, without WiFi or a strong cellular network, like a rural area, you'll...

$149.95

24 IN STOCK

Pimoroni pHAT Stack for Raspberry Pi

PRODUCT ID: 3742

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's pHAT Stack! This...

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's pHAT Stack! This expansive breakout PCB offers 6 sets of 2x20 pin headers - one for connecting to your Pi and the other 5 for a plethora of HATs, pHATs or bonnets. The combinations are endless... It's perfect for your projects, displaying temperatures, times, etc. and becomes really useful when combined...

$16.95

8 IN STOCK

Pimoroni Inky pHAT - eInk Display - Black/White

PRODUCT ID: 3934

Here at Adafruit we never tire of cool, new displays, so these super sweet e-paper displays really caught our eye! Pimoroni's Inky pHat is a...

Here at Adafruit we never tire of cool, new displays, so these super sweet e-paper displays really caught our eye! Pimoroni's Inky pHat is a petite 212x104 pixel two-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the 3-second display-change-cycle. But the...

$24.95

8 IN STOCK

Pimoroni Explorer pHAT for Raspberry Pi Zero

PRODUCT ID: 3018

The Explorer pHAT is the perfect prototyping side-kick for your Raspberry Pi. Based on Pimoroni's popular Explorer Hat Pro, this...

The Explorer pHAT is the perfect prototyping side-kick for your Raspberry Pi. Based on Pimoroni's popular Explorer Hat Pro, this is a smaller cheaper version designed to fit perfectly on a Raspberry Pi Zero! A heap of useful input and output options have been added that will take your projects to the next level. Great for driving motors, using analog sensors, and interfacing with 5V sensors & systems Though...

$14.95

65 IN STOCK

Pimoroni Inky wHAT (ePaper/eInk/EPD) - Red/Black/White

PRODUCT ID: 4143

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic paper...

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic paper displays to 4.2" glorious inches! Say hellooo to Inky wHAT ! You get 5x the number of pixels (400x300!) to use as an e-reader or maybe a weather display / calendar. Everything comes fully-assembled, so there's no soldering required! The display is securely plonked down to the Inky wHAT...

$64.95

15 IN STOCK

Pimoroni Inky wHAT (ePaper/eInk/EPD) - Black/White

PRODUCT ID: 4142

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic...

$54.95

6 IN STOCK

Pimoroni Rainbow HAT for Android Things™ and Raspberry Pi

PRODUCT ID: 3354

The Rainbow HAT from Pimoroni has a buffet of sensors, inputs, and displays to explore Android Things™. Use it as a weather station, a clock, a...

The Rainbow HAT from Pimoroni has a buffet of sensors, inputs, and displays to explore Android Things™. Use it as a weather station, a clock, a timer or stopwatch, a mood light, or endless other things. Pimoroni collaborated with the Android Things™ team at Google to create this great add-on board that features displays, sensors, sound, and lots of LEDs! It's the perfect introduction to developing Android Things applications on...

$24.95

IN STOCK

Coming Soon! Machine Learning BrainCraft HAT for Raspberry Pi 4

PRODUCT ID: 4374

Coming soon! Sign up to be notified when we have these in the store! The idea behind the BrainCraft board (stand-alone, and Pi “hat”) is...

Coming soon! Sign up to be notified when we have these in the store! The idea behind the BrainCraft board (stand-alone, and Pi “hat”) is that you’d be able to “craft brains” for Machine Learning on the EDGE, with Microcontrollers & Microcomputers. On ASK AN ENGINEER, our founder & engineer chatted with Pete Warden, the technical lead of the mobile, embedded TensorFlow Group on Google’s Brain...

MORE INFO

COMING SOON

Pimoroni Scroll HAT Mini for Raspberry Pi - PIM491

PRODUCT ID: 4671

A 17x7 matrix of bright white LEDs with individual brightness control, and four handy buttons, made for Raspberry Pi. Just the job for scrolling...

A 17x7 matrix of bright white LEDs with individual brightness control, and four handy buttons, made for Raspberry Pi. Just the job for scrolling messages, animations, and more! Scroll HAT Mini's 119 LEDs are plenty for scrolling text, and the individual PWM brightness control over each pixel opens up a whole heap of potential for swish animations. The buttons could be used to toggle through modes or menus, for playback control, or even...

MORE INFO

COMING SOON

Pimoroni Automation HAT Mini - PIM487

PRODUCT ID: 4672

Automate your world with Automation HAT Mini! Monitor and control up to 24V systems and see their status on the gorgeous full-colour display....

Automate your world with Automation HAT Mini! Monitor and control up to 24V systems and see their status on the gorgeous full-colour display. Don't be fooled by its size... Automation HAT Mini packs a whole bunch of functionality in. It has a relay, 3x buffered inputs 3x outputs, and 3x analog inputs, all 24V-tolerant. Last but not least, it has a beautiful 0.96" full-color IPS LCD to display the status of your systems. This...

MORE INFO

COMING SOON

Pimoroni Enviro + FeatherWing - PIM502

PRODUCT ID: 4674

Care about air with Enviro+ FeatherWing. It's packed full of environmental sensors that'll get you started in the world of citizen science....

Care about air with Enviro+ FeatherWing. It's packed full of environmental sensors that'll get you started in the world of citizen science. Monitor weather, light level, noise pollution, and air quality, in your local area and contribute your data to better understand trends in air pollution. Note: you'll need a Feather board to go with this FeatherWing. We'd recommend the Feather M4 Express or Feather nRF52840...

MORE INFO

COMING SOON

Pimoroni Unicorn pHAT - 4x8 RGB LED Shield for Raspberry Pi

PRODUCT ID: 3181

Snap the Pimoroni Unicorn pHAT on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a fun 4x8 RGB LED...

Snap the Pimoroni Unicorn pHAT on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a fun 4x8 RGB LED matrix powered directly from the Pi. The Unicorn pHAT provides a wash of controllable color that is ideal for mood-lighting, 4x8 pixel art, persistence of vision effects, status indications, or just blasting color into your surroundings. 32 fully controllable RGB LEDs (SK6218 - 3.5mm x...

$14.95

5 IN STOCK

Pimoroni Scroll pHAT HD – LED Matrix for Raspberry Pi Zero

PRODUCT ID: 3473

What if Scroll pHAT had twice times as many pixels and individual pixel brightness control? Scroll pHAT HD , that's what!! Scroll pHAT HD packs...

What if Scroll pHAT had twice times as many pixels and individual pixel brightness control? Scroll pHAT HD , that's what!! Scroll pHAT HD packs 17x7 bright white pixels (119 total) onto a single pHAT, and gives you full PWM brightness control over each pixel. Create beautiful animations and even anti-aliased text by taking advantage of the per-pixel brightness. Use Scroll pHAT HD as a scrolling message display for your tweets, the weather or...

$12.95

39 IN STOCK

Pimoroni Black HAT Hack3r Kit

PRODUCT ID: 2339

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT on your Raspberry Pi...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT on your Raspberry Pi Model Pi 3, 2, A+, or B+. The Pimoroni Black HAT Hack3r is ideal for debugging your HAT projects or combining a HAT with other circuits. Features: HAT spec landing area with PCB standoffsIncludes 40 pin GPIO ribbon cableAll GPIO pins labelled with function, BCM pin number, physical pin numberRubber...

MORE INFO

DISCONTINUED

Pimoroni Explorer HAT for Raspberry Pi

PRODUCT ID: 2426

The Explorer HAT is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer from Pimoroni there are a heap of...

The Explorer HAT is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features: 4x buffered 5V tolerant inputs Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V...

MORE INFO

DISCONTINUED

Extra-tall SMT GPIO Header for Raspberry Pi HAT - 2x20 Extra Tall Female Header

PRODUCT ID: 2714

PRODUCT ID: 3283

So you've got your Pi 3 with its built-in wireless LAN and Bluetooth, but what about your Pi Zero? Say hello to the IoT pHAT from Red...

So you've got your Pi 3 with its built-in wireless LAN and Bluetooth, but what about your Pi Zero? Say hello to the IoT pHAT from Red Bear! This Zero-size board provides WiFi (802.11bgn / 2.4GHz) and Bluetooth (v4.1 / BTLE) connectivity direct from the GPIO header. You don’t need to use a dongle plugged into the Pi Zero’s solitary data micro-USB port via a USB OTG adapter. Just snap it on top of a Raspberry Pi...

MORE INFO

DISCONTINUED

PRODUCT ID: 3475

AHOY , wanna spell out some LOVE with this COOL Raspberry Pi FOUR letter PHAT ? Pimoroni's Four Letter pHAT has four 14-segment displays that you...

AHOY , wanna spell out some LOVE with this COOL Raspberry Pi FOUR letter PHAT ? Pimoroni's Four Letter pHAT has four 14-segment displays that you can use to display text, numbers, and a host of other characters. The LEDs are a beautiful retro green, just like your old digital alarm clock. They're driven by the HT16K33 chip over I2C, which does all the multiplexing for you. While it is shaped and sized to match a Pi Zero, it works great...

MORE INFO

DISCONTINUED