Halloween

WE LOVE HALLOWEEN. It's one of the few times of year that wearing your Electronic Demon Costume or your NeoPixel Punk Collar will get some real recognition and not just confused stares. So here's our Halloween category - full of great products to help you win those costume contests, show off your maker skills to your friends, and make your house the creepiest on the block. It's full of wearables goodies, sound or motion sensors, and things that blink and glow. Just scrolling through will give you infinite project ideas and make you love Halloween as much as we do!

And don't forget to check out our Halloween YouTube playlist and our Halloween section in the Learn System for even more ideas!

Adafruit METRO 328 Fully Assembled - Arduino IDE compatible - ATmega328

PRODUCT ID: 50

We sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs,...

We sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most simple projects. When we need to go small, we use a Metro Mini or a Trinket M0, but when size isn't as much of a concern, we reach for an Adafruit METRO. New! We've updated this product to our Adafruit Metro 328, a...

$17.50

IN STOCK

Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit - v2.3

PRODUCT ID: 1438

The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the...

The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Instead of a L293D darlington driver, we now have the TB6612...

$19.95

IN STOCK

Adafruit GEMMA v2 - Miniature wearable electronic platform

PRODUCT ID: 1222

Deprecation Warning: The Gemma bit-bang USB technique it uses doesn't work as well as it did in 2014, many modern computers won't work well....

Deprecation Warning: The Gemma bit-bang USB technique it uses doesn't work as well as it did in 2014, many modern computers won't work well. So while we still carry the Gemma so that people can maintain some older projects, we no longer recommend it. Please check out the Gemma M0. It has built-in USB, more capabilities, and is comparable in price! Love FLORA but want a bite-sized version? Look no further, GEMMA is a tiny wearable...

$9.95

IN STOCK

NeoPixel Ring - 12 x 5050 RGB LED with Integrated Drivers

PRODUCT ID: 1643

Round and round and round they go! 12 ultra bright smart LED NeoPixels are arranged in a circle with 1.5" (37mm) outer diameter. The rings are...

Round and round and round they go! 12 ultra bright smart LED NeoPixels are arranged in a circle with 1.5" (37mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Each one has ~18mA constant current drive so the color will be very consistent...

$7.50

IN STOCK

NeoPixel Ring - 16 x 5050 RGB LED with Integrated Drivers

PRODUCT ID: 1463

Round and round and round they go! 16 ultra bright smart LED NeoPixels are arranged in a circle with 1.75" (44.5mm) outer diameter. The rings...

Round and round and round they go! 16 ultra bright smart LED NeoPixels are arranged in a circle with 1.75" (44.5mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Each one has ~18mA constant current drive so the color will be very...

$9.95

IN STOCK

Monochrome 1.3" 128x64 OLED graphic display

PRODUCT ID: 938

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of...

These displays are small, only about 1.3" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its...

$19.95

OUT OF STOCK

Lithium Ion Polymer Battery - 3.7v 2500mAh

PRODUCT ID: 328

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery, we also have a 1200mAh model The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a...

$14.95

IN STOCK

Adafruit Trinket - Mini Microcontroller - 5V Logic

PRODUCT ID: 1501

Deprecation Warning: The Trinket bit-bang USB technique it uses doesn't work as well as it did in 2014, many modern computers won't work...

Deprecation Warning: The Trinket bit-bang USB technique it uses doesn't work as well as it did in 2014, many modern computers won't work well. So while we still carry the Trinket so that people can maintain some older projects, we no longer recommend it. Please check out the Trinket M0. It has built-in USB, more capabilities, and is comparable in price! Trinket may be small, but do not be fooled by its size! It's a tiny...

$6.95

IN STOCK

Electret Microphone Amplifier - MAX4466 with Adjustable Gain

PRODUCT ID: 1063

Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz...

Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly as noisy or scratchy as other mic amp breakouts...

$6.95

IN STOCK

Lithium Ion Polymer Battery - 3.7v 500mAh

PRODUCT ID: 1578

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 500mAh for a total of about 1.9 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection...

$7.95

IN STOCK

Lithium Ion Polymer Battery - 3.7v 1200mAh

PRODUCT ID: 258

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 1200mAh for a total of about 4.5 Wh. If you need a larger battery, we also have a 2500mAh+ model The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a...

$9.95

IN STOCK

Photo cell (CdS photoresistor)

PRODUCT ID: 161

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about...

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side of the photo cell (either one, its symmetric) to power (for example 5V) and the other side to your microcontroller's analog input pin. Then connect a 10K pull-down resistor from that analog pin to ground. The voltage on...

$0.95

IN STOCK

JST-PH Battery Extension Cable - 500mm

PRODUCT ID: 1131

By popular demand, we now have a handy extension cord for all of our JST-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One...

By popular demand, we now have a handy extension cord for all of our JST-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in many other situations where you need a little more space. JST-PH Battery Extension Cable -...

$1.95

IN STOCK

2 x 2032 Coin Cell Battery Holder - 6V output with On/Off switch

PRODUCT ID: 783

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most popular size) in...

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most popular size) in series to generate 6V nominal. (If you want only 3V, we suggest sticking a crumpled piece of tin foil in one of the slots.) 20mm coin cells are popular as they are used in keychain lights, so they are easy to get, and fairly low cost. They tend to have about 220mAh capacity so this holder would...

$1.95

IN STOCK

3 x AAA Battery Holder with On/Off Switch and 2-Pin JST

PRODUCT ID: 727

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is slim,...

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is slim, and 3 AAA's add up to about 3.3-4.5V, a very similar range to Lithium Ion/polymer (Li-Ion) batteries and have an on-off switch. That makes them ideal for use with 3.3V projects that have a 2-pin JST connector meant for one of our Li-Ion/Poly batteries. (Of course, you can't recharge them...

$1.95

OUT OF STOCK

Micro servo

PRODUCT ID: 169

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller...

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller . You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. Of course, its not nearly as strong as a standard servo. Works...

$5.95

IN STOCK

Sewable CR2032 Battery Holder

PRODUCT ID: 653

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in...

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (negative) and the other tab is +3 Volts. This holder is meant to be used with Lithium CR2032 (20mm diameter, 3.2mm thick) sized coin batteries. These are almost always 3V at...

$1.95

IN STOCK

Lithium Ion Polymer Battery - 3.7v 150mAh

PRODUCT ID: 1317

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 150mAh for a total of about 0.6 Wh. If you need a larger battery, we have a full range of bigger cells The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they...

$5.95

IN STOCK

UBEC DC/DC Step-Down (Buck) Converter - 5V @ 3A output

PRODUCT ID: 1385

Your power supply problems just got SOLVED! This little circuit board may look tiny but inside is a high efficiency DC/DC step-down converter which...

Your power supply problems just got SOLVED! This little circuit board may look tiny but inside is a high efficiency DC/DC step-down converter which can output up to 3 Amp at 5V without the need of any heat-sink or forced cooling. (It does get a bit toasty at 3A though) UBEC stands for "universal battery eliminator circuit" and this UBEC is designed to replace a 5V supply in RC planes and 'copters but its also great for any kind of...

$9.95

IN STOCK

PIR (motion) sensor

PRODUCT ID: 189

PIR sensors are used to detect motion from pets/humanoids from about 20 feet away (possibly works on zombies, not guaranteed). This one has an...

PIR sensors are used to detect motion from pets/humanoids from about 20 feet away (possibly works on zombies, not guaranteed). This one has an adjustable delay before firing (approx 2-4 seconds), adjustable sensitivity and we include a 1 foot (30 cm) cable with a socket so you can easily reposition the sensor or mount it using the two holes on either side. Runs on 5V-12V power (if you need to run it off of 3V you can do that by bypassing the...

$9.95

IN STOCK

Pressure-Sensitive Conductive Sheet (Velostat/Linqstat)

PRODUCT ID: 1361

This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit....

This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's pressure-sensitive: squeezing it will reduce the resistance, so it's handy for making flexible sensors. And it's a lot less expensive than off-the-shelf pressure or bend sensors too! Each order comes with a 11"x11" (28cm x 28cm) 4mil (0.1mm) thick piece. We may fold the...

$4.95

IN STOCK

Flora RGB Smart NeoPixel version 2 - Pack of 4

PRODUCT ID: 1260

What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables,...

What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables, these updated Flora NeoPixels have ultra-cool technology: these ultra-bright LEDs have a constant-current driver cooked right into the LED package! The pixels are chainable - so you only need 1 pin/wire to control as many LEDs as you like. They're easy to sew, and the chainable design means no...

$7.95

IN STOCK

Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft

PRODUCT ID: 640

After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely...

After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely of 316L stainless steel. Once you start working with this thread you'll quickly agree its optimal for any wearables work! This thread is 2 ply, a little thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles or with a sewing machine that...

$6.95

IN STOCK

Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

PRODUCT ID: 815

You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of...

You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you could just get this handy PWM and Servo driver breakout. When we saw this chip, we quickly realized what an excellent add-on this would be. Using only two...

$14.95

100 IN STOCK

Adafruit Trinket - Mini Microcontroller - 3.3V Logic - MicroUSB

PRODUCT ID: 1500

Deprecation Warning: The Trinket bit-bang USB technique it uses doesn't work as well as it did in 2014, many modern computers won't work...

$6.95

IN STOCK

Electret Microphone Amplifier - MAX9814 with Auto Gain Control

PRODUCT ID: 1713

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a...

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret microphones in situations where the loudness of the audio isn't predictable. This fancy microphone amplifier module is a step above the rest, with built...

$7.95

OUT OF STOCK

Fast Vibration Sensor Switch (Easy to trigger)

PRODUCT ID: 1766

The "poor man's" accelerometer/motion sensor! These spring-vibration switches are high sensitivity non-directional vibration induced...

The "poor man's" accelerometer/motion sensor! These spring-vibration switches are high sensitivity non-directional vibration induced trigger switches. Inside is a very soft spring coiled around a long metal pin. When the switch is moved, the spring touches the center pole to make contact. So, when there's motion, the two pins will act like a closed switch. When everything is still, the switch is open. Great for basic projects...

$0.95

IN STOCK

Piezo Buzzer - PS1240

PRODUCT ID: 160

Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, connect...

Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, connect one pin to ground (either one) and the other pin to a square wave out from a timer or microcontroller. For the loudest tones, stay around 4 KHz, but works quite well from 2KHz to 10KHz. For extra loudness, you can connect both pins to a microcontroller and swap which pin is high or low...

$1.50

IN STOCK

Round Force-Sensitive Resistor (FSR) - Interlink 402

PRODUCT ID: 166

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink...

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink model 402 FSR with 1/2 diameter sensing region. FSR's are basically a resistor that changes its resistive value (in ohms Ω) depending on how much its pressed. These sensors are fairly low cost, and easy to use but they're rarely accurate. They also vary some from sensor to sensor perhaps...

$7.00

OUT OF STOCK

Standard LCD 16x2 + extras - white on blue

PRODUCT ID: 181

Standard HD44780 LCDs are useful for creating standalone projects. 16 characters wide, 2 rowsWhite text on blue backgroundConnection port is...

Standard HD44780 LCDs are useful for creating standalone projects. 16 characters wide, 2 rowsWhite text on blue backgroundConnection port is 0.1" pitch, single row for easy breadboarding and wiringPins are documented on the back of the LCD to assist in wiring it upSingle LED backlight included can be dimmed easily with a resistor or PWM and uses much less power than LCD with EL (electroluminescent) backlightsCan be fully controlled with...

$9.95

OUT OF STOCK

Adafruit LED Sequins - Warm White - Pack of 5

PRODUCT ID: 1758

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a...

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many projects. Simply connect 3 to 6VDC to the + pin and ground to the - pin, and the LED on the board will light up. You can make the LEDs fade and twinkle by using the PWM (a.k.a. analogWrite)...

$3.95

IN STOCK

NeoPixel Ring - 24 x 5050 RGB LED with Integrated Drivers

PRODUCT ID: 1586

Round and round and round they go! 24 ultra bright smart LED NeoPixels are arranged in a circle with 2.6" (66mm) outer diameter. The rings are...

Round and round and round they go! 24 ultra bright smart LED NeoPixels are arranged in a circle with 2.6" (66mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Each one has ~18mA constant current drive so the color will be very consistent even if the...

$16.95

IN STOCK

Adafruit 12-Key Capacitive Touch Sensor Breakout - MPR121

PRODUCT ID: 1982

Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the...

Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the MPR121. This chip can handle up to 12 individual touch pads. The MPR121 has support for only I2C, which can be implemented with nearly any microcontroller. You can select one of 4 addresses with the ADDR pin, for a total of 48 capacitive touch pads on one I2C 2-wire bus. Using this chip is a lot...

$7.95

42 IN STOCK

Hall effect sensor - US5881LUA

PRODUCT ID: 158

Hall effect sensors detect whether a magnet is near. Useful for non-contact/waterproof type switches, position sensors, rotary/shaft encoders. I...

Hall effect sensors detect whether a magnet is near. Useful for non-contact/waterproof type switches, position sensors, rotary/shaft encoders. I tried dozens of different hall effect sensors to see which one would work best for the SpokePOV kit (to determine the wheel location) and this one came out on top! Runs at 3.5V up to 24V. To use connect power to pin 1 (all the way to the left), ground to pin 2 (middle) and then a 10K pull up resistor...

$2.00

IN STOCK

Adafruit Wave Shield for Arduino Kit - v1.1

PRODUCT ID: 94

Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduino 328's that solves this problem. It can play...

Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduino 328's that solves this problem. It can play up to 22KHz 12bit uncompressed audio files of any length. It's low cost, available as an easy-to-make kit. It has an onboard DAC, filter and op-amp for high quality output. Audio files are read off of an SD/MMC card, which are available at nearly any store. Volume can be controlled with the...

$22.00

IN STOCK

Lithium Ion Battery Pack - 3.7V 6600mAh

PRODUCT ID: 353

Need a massive battery for your project? This lithium ion pack is made of 3 balanced 2200mAh cells for a total of 6600mA capacity! The cells are...

Need a massive battery for your project? This lithium ion pack is made of 3 balanced 2200mAh cells for a total of 6600mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage and over-current protection. Each cell can provide 0.5C of current (1.1 A per) so all together the peak current you can draw is over 3.3 Amps. Note that these batteries are not designed to sustain...

$29.50

IN STOCK

Adafruit MetroX Classic Kit - Experimentation Kit for Metro 328

PRODUCT ID: 170

Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete...

Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete over 20 different circuit and projects. Basically everything you need to be playing within minutes of its arrival. No soldering required, works with Mac, Windows and Linux! New! As of March 28, 2018 we've done a big refresh on this kit, to add more stuff like a character LCD, Infrared remote and...

$84.95

OUT OF STOCK

FLORA Budget Pack

PRODUCT ID: 1405

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer....

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3xAAA battery holder and batteries, a battery extension cable, our high quality stainless steel thread, alligator clips to help you test out your parts...

$34.95

OUT OF STOCK

Lithium Ion Polymer Battery - 3.7v 100mAh

PRODUCT ID: 1570

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of ~100mAh for a total of about 0.4 Wh. If you need a larger battery, we have a full range of bigger cells The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they...

$5.95

IN STOCK

Membrane 3x4 Matrix Keypad + extras - 3x4

PRODUCT ID: 419

Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin,...

Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin, flexible membrane material with an adhesive backing (just remove the paper) so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 7 microcontroller pins (3-columns and 4-rows) to scan through the pad. Check the tutorials tab for links to an Arduino library...

$3.95

91 IN STOCK

Standalone Momentary Capacitive Touch Sensor Breakout - AT42QT1010

PRODUCT ID: 1374

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is...

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor. When a capacitive load is detected (e.g. a person touches the sensor-pad area) the red LED lights up and the output pin goes high. You can also solder a wire to the middle pad and create your own capacitive pad if the...

$5.95

27 IN STOCK

Short Flex Sensor

PRODUCT ID: 1070

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface....

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. These sensors are easy to use, they are basically resistors that change value based on how much their flexed. If they're unflexed, the resistance is about ~25KΩ. When flexed all the way the resistance rises to ~100KΩ. They're pretty similar to FSRs so following this tutorial will...

$7.95

IN STOCK

High-strength 'rare earth' magnet

PRODUCT ID: 9

Yow! These things are super powerful. 1/2" diameter, 3/16" thick discs, south side is marked with a red line. Great for use with your...

Yow! These things are super powerful. 1/2" diameter, 3/16" thick discs, south side is marked with a red line. Great for use with your SpokePOV Kit. If you have an aluminium frame, use tape/foamstickytape to attach it.

$2.50

88 IN STOCK

Square Force-Sensitive Resistor (FSR) - Interlink 406

PRODUCT ID: 1075

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink...

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink model 406 FSR with a 38mm square sensing region. Note that this sensor can't detect where on the square you pressed (for that, check out our ribbon soft pots or capacitive touch pad ). FSRs are basically a resistor that changes its resistive value (in ohms Ω) depending on how much its...

$8.95

6 IN STOCK

Membrane LED Keypad + extras

PRODUCT ID: 1333

This membrane keypad has a single key, but it does have an embedded surface-mount red LED installed. The flex cable is also extra-long, so we can...

This membrane keypad has a single key, but it does have an embedded surface-mount red LED installed. The flex cable is also extra-long, so we can think of a lot of wearable and portable projects that would use this sort of switch and have an LED as feedback (say, to indicate that an action is occuring or the power is on). Since the keypad is soft plastic, it can be sewn with needle and thread. The back of the pad has a removable paper cover that...

$2.95

IN STOCK

Lithium Ion Cylindrical Battery - 3.7v 2200mAh

PRODUCT ID: 1781

Need a big battery for your project? This lithium ion battery contains a 2200mAh and a protection circuit that provides over-voltage, under-voltage...

Need a big battery for your project? This lithium ion battery contains a 2200mAh and a protection circuit that provides over-voltage, under-voltage and over-current protection. Yet, it is slim and easy to fit into many project cases. This cell can provide 2 C of peak current (4400mA). Note that these batteries are not designed to sustain such high loads, we suggest keeping any constant current draw under about 0.5 C (1 Amp) The battery comes...

$9.95

IN STOCK

Speaker - 3" Diameter - 8 Ohm 1 Watt

PRODUCT ID: 1313

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power....

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our Wave shield or class D amplifier board. Speaker - 3" Diameter - 8 Ohm 1 Watt (0:01)

$1.95

OUT OF STOCK

Continuous Rotation Servo - FeeTech FS5103R

PRODUCT ID: 154

This servo rotates fully forward or backwards instead of moving to a position. You can use any servo code, hardware or library to control these...

This servo rotates fully forward or backwards instead of moving to a position. You can use any servo code, hardware or library to control these servos. Good for making simple moving robots. Comes with four different horns, as shown. To control with an Arduino, we suggest connecting the control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE (see here for an example sketch). Position "90" (1.5ms pulse)...

$11.95

IN STOCK

Stereo 20W Class D Audio Amplifier - MAX9744

PRODUCT ID: 1752

Pump up the volume with this 20W stereo amplifier! This slim little board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm...

Pump up the volume with this 20W stereo amplifier! This slim little board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Power it with 5-12VDC using the onboard DC power jack and plug stereo line level into the 3.5mm stereo headphone jack and jam out with ease. Since it's class D, its completely cool-running, no heat sinks are required and it's extremely efficient - up to 93%...

$19.95

OUT OF STOCK

Lithium Ion Battery Pack - 3.7V 4400mAh

PRODUCT ID: 354

Need a big battery for your project? This lithium ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are...

Need a big battery for your project? This lithium ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage and over-current protection. Each cell can provide 1A of current for about 4 hours so all together the peak current you can draw is a little over 1.5 Amps. Note that these batteries are not designed to...

$19.95

IN STOCK

Adafruit Audio FX Sound Board - WAV/OGG Trigger with 16MB Flash

PRODUCT ID: 2220

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming...

$24.95

OUT OF STOCK

Adafruit LED Sequins - Royal Blue - Pack of 5

PRODUCT ID: 1757

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a...

$3.95

IN STOCK

Adafruit LED Sequins - Ruby Red - Pack of 5

PRODUCT ID: 1755

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a...

$3.95

IN STOCK

Slow Vibration Sensor Switch (Hard to trigger)

PRODUCT ID: 1767

The "poor man's" accelerometer/motion sensor! These spring-vibration switches are low sensitivity non-directional vibration induced...

The "poor man's" accelerometer/motion sensor! These spring-vibration switches are low sensitivity non-directional vibration induced trigger switches. Inside is a stiff spring coiled around a long metal pin. When the switch is moved, the spring touches the center pole to make contact. So, when there's motion, the two pins will act like a closed switch. When everything is still, the switch is open. Great for basic projects and...

$0.95

IN STOCK

VCNL4010 Proximity/Light sensor

PRODUCT ID: 466

The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. For longer distances (in the range of cm,...

The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. For longer distances (in the range of cm, you can use a SHARP IR distance sensor, but those are only good if the object is over 10 cm away. The VCNL4010 is designed for much shorter distances, no more than 200mm (about 7.5") and under our experimentation we found it worked best at distances of about 10-150mm. It would be good for say...

$7.50

IN STOCK

Adafruit Mini Lipo w/Mini-B USB Jack - USB LiIon/LiPoly charger - v1

PRODUCT ID: 1905

Oh so handy, this little lipo charger is so small and easy to use you can keep it on your desk or mount it easily into any project! Simply plug it...

Oh so handy, this little lipo charger is so small and easy to use you can keep it on your desk or mount it easily into any project! Simply plug it via any MiniUSB cable into a USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit. When the battery is fully charged and ready for use, the green LED turns on....

$6.95

OUT OF STOCK

Tilt ball switch

PRODUCT ID: 173

The "poor man's" accelerometer! Tilt sensors are switches that can detect basic motion/orientation. The metal tube has a little metal...

The "poor man's" accelerometer! Tilt sensors are switches that can detect basic motion/orientation. The metal tube has a little metal ball that rolls around in it, when its tilted upright, the ball rolls onto the contacts sticking out of end and shorts them together. Be sure to read our detailed tutorial including diagrams and example code.

$2.00

IN STOCK

Tactile On/Off Switch with Leads

PRODUCT ID: 1092

Squeeze once to turn on, squeeze again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because...

Squeeze once to turn on, squeeze again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's easy to embed in a seam for easily powering up/off wearable and fabric projects. Can handle up to 14V and 2 Amps! This is a really satisfying switch. As of May 20th, the dimensions of this switch are: Length of wires: 190mm / 7.5"Dimensions of body: 16mm x 15mm x 6mm / 0.6" x 0.6"...

$3.95

OUT OF STOCK

Membrane 1x4 Keypad + Extras

PRODUCT ID: 1332

Punch in your secret key into this numeric membrane keypad. This keypad has 4 buttons, and since every key has its own wire line, no matrix code is...

Punch in your secret key into this numeric membrane keypad. This keypad has 4 buttons, and since every key has its own wire line, no matrix code is required - just treat these like every day switches. The membrane is soft and has a removable paper backing to expose a strong adhesive so you can stick this on an enclosure and feed the cable through a slot. Its a simple keypad but that's why we like it. We include a 5-pin extra-long header...

$2.95

IN STOCK

Adafruit Bicolor LED Square Pixel Matrix with I2C Backpack

PRODUCT ID: 902

What's better than a single LED? Lots of LEDs! A fun way to make a small colorful display is to use a 1.2" Bi-color 8x8 LED Matrix. Matrices...

What's better than a single LED? Lots of LEDs! A fun way to make a small colorful display is to use a 1.2" Bi-color 8x8 LED Matrix. Matrices like these are 'multiplexed' - so to control all the 128 LEDs you need 24 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can help control a matrix for you but there's a lot of wiring to set up and they take up a ton of space. Here at Adafruit we feel...

$15.95

IN STOCK

Needle set - 3/9 sizes - 20 needles

PRODUCT ID: 615

Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our conductive...

Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our conductive thread and wearable electronics parts. Each pack contains 20 gold-eye sharps, with eye sizes ranging from #3 (1.75" long) to #9 (1.35" long). The two #3's (the largest) are too large to pass through the sewable coin cell holder but otherwise are easy to use and thread. The four #9's...

$1.95

IN STOCK

Adafruit LED Sequins - Emerald Green - Pack of 5

PRODUCT ID: 1756

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a...

$3.95

IN STOCK

Long Flex sensor

PRODUCT ID: 182

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface....

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. These sensors are easy to use, they are basically resistors that change value based on how much they're flexed. If they're unflexed, the resistance is about ~10KΩ. When flexed all the way the resistance rises to ~20KΩ. They're pretty similar to FSRs so following this...

$12.95

OUT OF STOCK

IR distance sensor includes cable (10cm-80cm) - GP2Y0A21YK0F

PRODUCT ID: 164

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how...

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 12" long 3-JST interface wire. These sensors are good for short-range detection. For over 1 m distance, we suggest using sonar sensors To use, connect black wire to ground, red wire to 5V and white wire to analog input. The analog voltage out will range...

$14.95

IN STOCK

12V EL wire/tape inverter

PRODUCT ID: 448

This is an inverter for EL wire and tape, similar to our pocket inverters, except it is a brick that takes 12V input instead of 2 AA batteries. This...

This is an inverter for EL wire and tape, similar to our pocket inverters, except it is a brick that takes 12V input instead of 2 AA batteries. This means its good for 'fixed' installations since you can just plug it into a 12V wall adapter. It's also good for portable projects where you want to have a big battery pack like a 8xAA holder which will last 4-5 times longer than just 2xAA's. It is also more powerful, and can drive...

$4.95

IN STOCK

Standalone Toggle Capacitive Touch Sensor Breakout - AT42QT1012

PRODUCT ID: 1375

This breakout board is the simplest way to create a project with a single "toggle" capacitive touch sensor. No microcontroller is required...

This breakout board is the simplest way to create a project with a single "toggle" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor. This sensor is a toggle output type: touch-on then touch-off. That means that when a capacitive load is detected (e.g. a person touches the sensor-pad area) the red LED will alternate turning off and the output pin will...

$5.95

IN STOCK

Miniature Ultra-Bright 8x8 White LED Matrix

PRODUCT ID: 1079

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but...

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite-sized! 64 bright white LEDs are contained inside the plastic body, in an 8x8 matrix. There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space to wire it up Since the display is in a grid, you'll need to 1:8 multiplex control...

$7.50

IN STOCK

TTL Serial JPEG Camera with NTSC Video

PRODUCT ID: 397

This camera module can be a pretty neat project addition. It was designed to be used in security systems and does two main things - it outputs NTSC...

This camera module can be a pretty neat project addition. It was designed to be used in security systems and does two main things - it outputs NTSC video and can take snapshots of that video (in color) and transmit them over the TTL serial link. You can snap pictures at 640x480, 320x240 or 160x120 and they're pre-compressed JPEG images which makes them nice and small and easy to store on an SD card. Perfect for a data-logging, security, or...

$39.95

IN STOCK

Waterproof 3xAA Battery Holder with On/Off Switch

PRODUCT ID: 771

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for...

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the hexnuts are captive in one side and you can assemble/disassemble as many times as you...

$3.95

IN STOCK

Flex PCB Material - Pyralux - 6" by 6" Square - AC 352500EY

PRODUCT ID: 1894

Finally, the conductive material you've known you wanted but never knew you could have, its a sheet of flex PCB material! This is the stuff used...

Finally, the conductive material you've known you wanted but never knew you could have, its a sheet of flex PCB material! This is the stuff used to make flexible circuits, but raw and unetched. You can treat it just like 1 oz copper clad, etch it with ferric chloride (or other PCB etching systems) or cut with scissors. It may even be possible to laser or CNC engrave (we haven't tried it ourselves but we'd love to hear about it if you...

$9.95

OUT OF STOCK

Gemma Starter Pack

PRODUCT ID: 1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA...

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a USB cable for programming GEMMA. Note : As of June 20th, 2016 this pack no longer comes with CR2032 batteries to make shipping easier for customers. You...

$27.95

IN STOCK

Budget Pack for Metro 328 - with Assembled Metro ATmega328P

PRODUCT ID: 193

This budget pack is an optimized collection of parts and pieces to experiment with Adafruit Metro 328 and the Arduino IDE at home, school or work....

This budget pack is an optimized collection of parts and pieces to experiment with Adafruit Metro 328 and the Arduino IDE at home, school or work. Great for students and those that want to get their feet wet, no soldering required! Includes the Adafruit Metro 328 with thru-hole headers. The Metro is our take on the most maker-friendly Arduino-compatible board. It is the culmination of years of playing with electronics: we wanted to make a...

$29.95

46 IN STOCK

Adafruit "Music Maker" MP3 Shield for Arduino (MP3/Ogg/WAV...)

PRODUCT ID: 1790

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding...

Bend all audio files to your will with the Adafruit Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and...

$29.95

OUT OF STOCK

Super Bright Blue 5mm LED (25 pack)

PRODUCT ID: 301

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have...

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 clear blue LEDs5mm diameter465 nm wavelength3.2-3.8V Forward Voltage, at 20mA current6000 mcd typical brightnessViewing Angle : ±10 degreesMaximum continuous current: 30mA If you...

$8.00

IN STOCK

Adafruit Audio FX Sound Board - WAV/OGG Trigger with 2MB Flash

PRODUCT ID: 2133

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers,...

$19.95

53 IN STOCK

IR distance sensor includes cable (20cm-150cm) - GP2Y0A02YK

PRODUCT ID: 1031

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how...

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 8" long 3-JST interface wire. These sensors are good for detection between 20cm-150cm. For over 1 m distance, we suggest using sonar sensors. To use, connect black wire to ground, red wire to 5V and white wire to analog input. The analog voltage out will...

$15.95

34 IN STOCK

CAP1188 - 8-Key Capacitive Touch Sensor Breakout - I2C or SPI

PRODUCT ID: 1602

Add lots of touch sensors to your next microcontroller project with this easy-to-use 8-channel capacitive touch sensor breakout board, starring the...

Add lots of touch sensors to your next microcontroller project with this easy-to-use 8-channel capacitive touch sensor breakout board, starring the CAP1188. This chip can handle up to 8 individual touch pads, and has a very nice feature that makes it stand out for us: it will light up the 8 onboard LEDs when the matching touch sensor fires to help you debug your sensor setup. The CAP1188 has support for both I2C and SPI, so it easy to use with...

$7.95

IN STOCK

Pulse Sensor Amped

PRODUCT ID: 1093

Pulse Sensor Amped is a greatly improved version of the original Pulse Sensor, a plug-and-play heart-rate sensor for Arduino and Arduino compatibles....

Pulse Sensor Amped is a greatly improved version of the original Pulse Sensor, a plug-and-play heart-rate sensor for Arduino and Arduino compatibles. It can be used by students, artists, athletes, makers, and game & mobile developers who want to easily incorporate live heart-rate data into their projects. Pulse Sensor Amped adds amplification and noise cancellation circuitry to the hardware. It's noticeably faster and easier to get...

$25.00

86 IN STOCK

Waterproof 2xAA Battery Holder with On/Off Switch

PRODUCT ID: 770

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for...

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the hexnuts are captive in one side and you can assemble/disassemble as many times as you...

$3.95

OUT OF STOCK

Adafruit LED Sequins - Rose Pink - Pack of 5

PRODUCT ID: 1792

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a...

$3.95

IN STOCK

Miniature TTL Serial JPEG Camera with NTSC Video

PRODUCT ID: 1386

This tiny little camera module can be a pretty neat project addition, it is just like our other JPEG cameras (same chipset/software), but much...

This tiny little camera module can be a pretty neat project addition, it is just like our other JPEG cameras (same chipset/software), but much smaller and slimmer. It was designed to be used in security systems and does two main things - it outputs NTSC color video and can take snapshots of that video (in color) and transmit them over the TTL serial link. You can snap pictures at 640x480, 320x240 or 160x120 and they're pre-compressed JPEG...

$35.95

IN STOCK

Adafruit Mini 8x8 LED Matrix w/I2C Backpack - Red

PRODUCT ID: 870

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can control a matrix for you but there's a lot of wiring to set up and they take up a ton of space. Here at Adafruit we feel your pain! After...

$9.95

IN STOCK

EL wire 2xAA pocket inverter

PRODUCT ID: 317

A small, portable inverter for EL wire. Powers off of 2 AA batteries (not included!), it can drive 1 to 8 feet (about 2.5m) of our high-brightness EL...

A small, portable inverter for EL wire. Powers off of 2 AA batteries (not included!), it can drive 1 to 8 feet (about 2.5m) of our high-brightness EL wire for 10 hours. There is a button for selecting steady/blink/off modes. There's a removable clip on the back. Comes with a 2.5mm pitch female JST connector To connect a piece EL wire to this, you'll want a male connector wire The EL inverter requires a 'load' to stabilize itself....

$7.50

IN STOCK

Magnetic Pin Back

PRODUCT ID: 1170

These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets. Affix the metal bar...

These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets. Affix the metal bar to your FLORA projects-- it's just the right size! Then attach your FLORA project to any garment without poking holes in your clothes. The magnets are strong enough to hold up even a hefty circuit! We recommend against soldering/brazing/welding to any part of the magnetic pin back, as the...

$1.95

IN STOCK

Blue Electroluminescent (EL) Tape Strip - 100cm w/two connectors

PRODUCT ID: 447

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape...

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't...

$8.95

18 IN STOCK

EL wire 4xAAA pocket inverter

PRODUCT ID: 564

A small, portable inverter for EL wire. Powers off of 4 AAA batteries (not included!), it can drive 3-4 meters (10 to 13 feet) of our high-brightness...

A small, portable inverter for EL wire. Powers off of 4 AAA batteries (not included!), it can drive 3-4 meters (10 to 13 feet) of our high-brightness EL wire OR 1 meter (3 feet) of EL tape OR a 10cmx10cm piece of EL panel for about 7 hours. There is a switch for selecting steady/blink/off modes. Comes with four 2.5mm pitch female JST connectors, standard for all the EL wire and tape we carry. The JST cables snap into the inverter, so if you...

$9.95

IN STOCK

Small 1.2" 8x8 Ultra Bright White LED Matrix + Backpack

PRODUCT ID: 1614

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$13.50

IN STOCK

Maxbotix Ultrasonic Rangefinder - LV-EZ1 - LV-EZ1

PRODUCT ID: 172

LV-EZ1 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects...

LV-EZ1 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches out to 254-inches with 1-inch resolution. (Objects from 0 inches to 6-inches range as 6-inches.) The interface output formats included are pulse width output (PWM), analog voltage output (Vcc/512 volts per...

$24.95

39 IN STOCK

Sensor pack 900

PRODUCT ID: 176

An assortment of the most common sensors used in electronics. 9 sensors and 3 additional components to interface with the 'analog world'. We...

An assortment of the most common sensors used in electronics. 9 sensors and 3 additional components to interface with the 'analog world'. We have some tutorials here, to get you started. Includes Triple-axis analog accelerometer - for measuring motion and tiltForce sensitive resistor - for sensing pressure/forceTemperature sensor - for measuring from -40 to over +125 degrees C10K breadboard potentiometerHall effect sensor - for sensing a...

$35.00

84 IN STOCK

IR Distance Sensor - Includes Cable (100cm-500cm) - GP2Y0A710K0F

PRODUCT ID: 1568

This extra-long-range SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used...

This extra-long-range SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 6" long 6-JST interface wire. These sensors are good for detection between 100cm-500cm (1-5 meters / 3-15 feet). The long range makes them a good alternative to sonar sensors. Please note: the wire colorings are not intuitive! Watch out...

$29.95

IN STOCK

Digital RGB LED Weatherproof Strip - LPD8806 32 LED

PRODUCT ID: 306

These LED strips are fun and glowy. There are 32 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the...

These LED strips are fun and glowy. There are 32 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 7-bit PWM precision (so 21-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 2 digital...

$29.95 / meter

51 IN STOCK

Conductive Hook & Loop Tape - 3" long

PRODUCT ID: 1324

Conductive hook & loop tape is just like the stuff you've seen on jackets, clothes, shoes, and bags, but is coated with silver to make it...

Conductive hook & loop tape is just like the stuff you've seen on jackets, clothes, shoes, and bags, but is coated with silver to make it fully conductive. Originally this was designed to the manufacture of static-safe clothing, but its great for wearable applications as well. For example an on-off switch or sensor. Each order ships with three inches of BOTH halves, its easily sewn or cut. Conductive Hook & Loop Tape - 3" long...

$5.95

IN STOCK

Adafruit Mini 8x8 LED Matrix w/I2C Backpack - Blue

PRODUCT ID: 959

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$11.95

IN STOCK

High Brightness Blue Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 408

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid blue. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to...

$12.00

IN STOCK

Sugru - Black and White Pack

PRODUCT ID: 437

Sugru! Soft-touch silicone rubber that molds and sets permanently. Sticks to aluminum, steel, ceramics, glass, wood and some fabrics + plastics!...

Sugru! Soft-touch silicone rubber that molds and sets permanently. Sticks to aluminum, steel, ceramics, glass, wood and some fabrics + plastics! sugru is the incredible new air-curing rubber for hackers, makers, gadget lovers & anyone else who wants to make things or make their stuff work better. Self-adhesive to most other materials, and flexible when cured, sugru is a versatile tool for hackers and makers - Repair and strengthen damaged...

$17.95

OUT OF STOCK

Wire Light LED Strand - 12 Blue LEDs + Coin Cell Holder

PRODUCT ID: 895

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated...

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof...

$4.95

54 IN STOCK

Adafruit Mini 8x8 LED Matrix w/I2C Backpack - Ultra Bright White

PRODUCT ID: 1080

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$13.50

IN STOCK

Adafruit Mini 0.8" 8x8 LED Matrix w/I2C Backpack - Yellow-Green

PRODUCT ID: 872

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$9.95

IN STOCK

Wire Light LED Strand - 12 Warm White LEDs + Coin Cell Holder

PRODUCT ID: 893

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated...

$4.95

OUT OF STOCK

Electroluminescent (EL) Panel - 10cm x 10cm White

PRODUCT ID: 625

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible...

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is 10 cm x 10 cm (approx: 4" x 4").There's a plastic coating is about 10.4cm x 10.4cm. Its covered in what seems to be PVC, the tape is thus...

$13.95

41 IN STOCK

Extra-long force-sensitive resistor (FSR) - Interlink 408

PRODUCT ID: 1071

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink...

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink model 408 FSR with a massive 1/4-inch x 24-inch sensing region. You can press anywhere along the strip and the pressure will be recognized. Note that this sensor can't detect where on the strip you pressed (for that, check out our ribbon soft pots). FSRs are basically a resistor that changes its...

$19.95

IN STOCK

Adafruit Small 1.2" 8x8 LED Matrix w/I2C Backpack - Blue

PRODUCT ID: 1052

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$11.95

IN STOCK

High Brightness Red Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 403

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid red. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to...

$12.00

88 IN STOCK

Melexis Contact-less Infrared Sensor - MLX90614 5V

PRODUCT ID: 1748

This cyber-tronic looking sensor hides a secret behind its glimmering eye. Unlike most temperature sensors, this sensor measures infrared light...

This cyber-tronic looking sensor hides a secret behind its glimmering eye. Unlike most temperature sensors, this sensor measures infrared light bouncing off of remote objects so it can sense temperature without having to touch them physically. Simply point the sensor towards what you want to measure and it will detect the temperature by absorbing IR waves emitted. Because it doesn't have to touch the object it's measuring, it can sense a...

$15.95

32 IN STOCK

Heart Rate Educational Starter Pack with Polar Wireless Sensors

PRODUCT ID: 1077

Read wireless heart-rate data into your electronics projects in under 10 minutes with this educational experimentation kit for Polar wireless heart...

Read wireless heart-rate data into your electronics projects in under 10 minutes with this educational experimentation kit for Polar wireless heart rate bands. This pack is designed for students, hobbyists, engineers and artists who want to add biometric interactivity to electronics. This is the easiest way possible to do it! No gel, no probes, no calibration and no clips. Simply strap the band on and detect heartbeats from 4 feet away. Please...

$65.00

4 IN STOCK

Maxbotix Ultrasonic Rangefinder - LV-EZ0 - LV-EZ0

PRODUCT ID: 979

LV-EZ0 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects...

LV-EZ0 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches out to 254-inches with 1-inch resolution. (Objects from 0 inches to 6-inches range as 6-inches.) The interface output formats included are pulse width output (PWM), analog voltage output (Vcc/512 volts per...

$26.95

39 IN STOCK

High Brightness Aqua Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 409

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot less power! We've got 2.6mm thickness EL...

$12.00

IN STOCK

Red Electroluminescent (EL) Tape Strip - 100cm w/two connectors

PRODUCT ID: 445

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape...

$8.95

23 IN STOCK

FLORA GPS Starter Pack

PRODUCT ID: 1090

Get started with the fabulous Adafruit Flora platform with this lovely starter kit. Included are plenty of parts to make a few different fun...

Get started with the fabulous Adafruit Flora platform with this lovely starter kit. Included are plenty of parts to make a few different fun projects! There's a Flora motherboard, a GPS module that can also perform location datalogging, eight ultra-bright chainable RGB pixels, a battery holder and batteries, two types of our high quality stainless steel thread, alligator clips to help you test out your parts, a USB cable for reprogramming the...

$89.95

OUT OF STOCK

Maxbotix Ultrasonic Rangefinder - LV-EZ4 - LV-EZ4

PRODUCT ID: 982

LV-EZ4 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects...

LV-EZ4 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches out to 254-inches with 1-inch resolution. (Objects from 0 inches to 6-inches range as 6-inches.) The interface output formats included are pulse width output (PWM), analog voltage output (Vcc/512 volts per...

$24.95

2 IN STOCK

High Brightness Green Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 407

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid lime green. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some...

$12.00

IN STOCK

Super Scissors - PH-57

PRODUCT ID: 1599

Save your scissors! Instead of using your nice shears (and dulling them) or wire cutters (not right for the job) - use these super scissors....

Save your scissors! Instead of using your nice shears (and dulling them) or wire cutters (not right for the job) - use these super scissors. They're meant for engineering/maker cutting jobs such as cutting plastic, leather, copper sheet/wire, even coaxial & ribbon cables. There's a notched flat section and a grippy tooth section. Notched (front) section capabilities: Nylon/Kevlar fiber: Various typesCopper braided wire: Various...

$14.95

24 IN STOCK

Small 1.2" 8x8 Ultra Bright Blue LED Matrix - KWM-30881CBB

PRODUCT ID: 1047

Make a scrolling sign, or a small video display with this 8x8 gridded blue LED matrix. Only 1.2" on a side, it is quite visible but not so large...

Make a scrolling sign, or a small video display with this 8x8 gridded blue LED matrix. Only 1.2" on a side, it is quite visible but not so large it wont plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. Since the display is in a grid, you'll need to 1:8 multiplex control it. We suggest either using a 74HC595 and...

$5.95

IN STOCK

Silicone Cicoil Wire Cable - 4-pin 24AWG

PRODUCT ID: 1437

This supple, slippery silicone wire has 4 conductors, 24AWG each sealed in a full silicone casing. It's heavy duty so you can pass tons of...

This supple, slippery silicone wire has 4 conductors, 24AWG each sealed in a full silicone casing. It's heavy duty so you can pass tons of current but soft and flexible so its good for wearables. We think this would be a good pair for our LED strips. Silicone Cicoil Wire Cable - 4-pin 24AWG (0:05)

$9.95

5 IN STOCK

White Electroluminescent (EL) Tape Strip -100cm w/two connectors

PRODUCT ID: 416

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape...

$8.95

OUT OF STOCK

High Brightness White Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 410

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. This EL is pink-coated so that it looks white. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot...

$12.00

IN STOCK

Miniature 8x8 Yellow LED Matrix

PRODUCT ID: 860

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, it's got everything a big LED matrix has, but...

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, it's got everything a big LED matrix has, but bite sized! 64 bright yellow LEDs are contained inside the plastic body, in an 8x8 matrix. There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space to wire it up. Since the display is in a grid, you'll need to 1:8 multiplex...

$3.95

IN STOCK

Adafruit Small 1.2" 8x8 LED Matrix w/I2C Backpack - Red

PRODUCT ID: 1049

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$9.95

IN STOCK

Music & sound add-on pack for Arduino - v1.1

PRODUCT ID: 175

Its a Wave shield party pack! Just add an Arduino to create your own iPod-killer, audio art, sound-effects box... Comes with: Latest Wave shield kit,...

Its a Wave shield party pack! Just add an Arduino to create your own iPod-killer, audio art, sound-effects box... Comes with: Latest Wave shield kit, works with more SD cards and with older NG Arduinos! Unassembled1 or 2 GB SD card (brand or size may change, but we test one of each kind to verify it works well)Speaker - 3" diameter (77mm), 8 ohm impedence, good response between 200Hz to 10KHz (10KHz is the max frequency the Wave shield can...

$35.00

OUT OF STOCK

EL wire starter pack - Red 2.5 meter (8.2 ft)

PRODUCT ID: 587

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Red. 2.5 meters is...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Red. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change...

$19.95

88 IN STOCK

EL wire starter pack - Aqua 2.5 meter (8.2 ft)

PRODUCT ID: 545

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Aqua, the brightest...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Aqua, the brightest and best looking EL color we carry. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL...

$19.95

IN STOCK

High Brightness Orange Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 405

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid orange. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow...

$12.00

95 IN STOCK

Diffused Red 10mm LED (25 pack)

PRODUCT ID: 845

Need some big indicators? We are big fans of these huge diffused red LEDs. They are fairly bright so they can be seen in daytime, and from any angle....

Need some big indicators? We are big fans of these huge diffused red LEDs. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project. Pack of 25 diffused red LEDs10mm diameter660 nm wavelength1.85-2.5V Forward Voltage, at 20mA current1000 mcd typical brightnessDatasheet If you need some help using LEDs, please read our "Introduction to using...

$9.95

OUT OF STOCK

Wire Light LED Strand - 12 Cool White LEDs + Coin Cell Holder

PRODUCT ID: 894

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated...

$4.95

IN STOCK

Adafruit Mini 8x8 LED Matrix w/I2C Backpack - Yellow

PRODUCT ID: 871

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$9.95

IN STOCK

High Brightness Yellow Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 406

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid yellow. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow...

$12.00

98 IN STOCK

Green Electroluminescent (EL) Tape Strip - 100cm w/2 connectors

PRODUCT ID: 446

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape...

$8.95

12 IN STOCK

Electroluminescent (EL) Panel - 10cm x 10cm Blue

PRODUCT ID: 624

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible...

EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is 10 cm x 10 cm (approx: 4" x 4"). There's a plastic coating is about 10.4cm x 10.4cm. Its covered in what seems to be PVC, the tape is thus...

$13.95

13 IN STOCK

Aqua Electroluminescent (EL) Tape Strip - 100cm w/two connectors

PRODUCT ID: 415

EL tape is the big sister to EL wire - it has the same glow effect but with a flat, wide shape instead of a round shape. The glowing part of the tape...

$8.95

OUT OF STOCK

Tactile Alternating Button w/3 Wire Leads

PRODUCT ID: 1685

Push once to turn one side on, push again to turn the other side on! It's basically a push-button toggle switch that connects and disconnects the...

Push once to turn one side on, push again to turn the other side on! It's basically a push-button toggle switch that connects and disconnects the middle pin from either of the two side switches with every click. This clicky switch makes a great power switch or mode toggler. We like this switch because it's easy to embed in a seam for easily powering up/off multi-wire wearable and fabric projects. Can reliably handle up to 3A and up to...

$3.95

OUT OF STOCK

Wire Light LED Strand - 12 Red LEDs + Coin Cell Holder

PRODUCT ID: 897

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated...

$4.95

6 IN STOCK

Adafruit Small 1.2" 8x8 LED Matrix w/I2C Backpack - Pure Green

PRODUCT ID: 1632

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$10.95

IN STOCK

Miniature 8x8 Red LED Matrix

PRODUCT ID: 454

You will squeak with delight when you hold this adorable miniature LED 8x8 matrix. 0.8" square, it's got everything a big LED matrix has,...

You will squeak with delight when you hold this adorable miniature LED 8x8 matrix. 0.8" square, it's got everything a big LED matrix has, but bite-sized! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space to wire it up Since the display is in a grid, you'll need to 1:8 multiplex control it. We suggest either using a 74HC595 and TPIC6B595 (using the...

$3.95

IN STOCK

Small 1.2" 8x8 Bi-Color (Red/Green) Square LED Matrix

PRODUCT ID: 458

Make a scrolling sign, or a small video display with this 8x8 gridded bi-color LED matrix. Only 1.2" on a side, it is quite visible but not so...

Make a scrolling sign, or a small video display with this 8x8 gridded bi-color LED matrix. Only 1.2" on a side, it is quite visible but not so large it wont plug into a breadboard! Every grid has two LEDs inside so you can have it display red, green, yellow or with fast multiplexing any color in between. This display is bright, beautiful and funky with nice diffused square lenses for a striking look. There are 24 pins on the side, 12 on...

$7.95

IN STOCK

EL Wire 6V Sound Activated Pocket Inverter

PRODUCT ID: 831

A small, portable inverter for EL wire with an audio input! This inverter has a little microphone and will light the connected EL according to the...

A small, portable inverter for EL wire with an audio input! This inverter has a little microphone and will light the connected EL according to the surrounding audio volume. Makes for an easy reactive project. This inverter requires 6V input (it works great with our 4xAA battery holder) and it can drive 2-3 meters (7 to 10 feet) of our high-brightness EL wire OR 1 meter (3 feet) of EL tape OR a 10cmx10cm piece of EL panel continuously for about...

$9.95

53 IN STOCK

Costume Goggles

PRODUCT ID: 1577

We've got some awesome LED goggle tutorials, and now you want to make your own, right? So pick up a pair of NeoPixel rings and these costuming...

We've got some awesome LED goggle tutorials, and now you want to make your own, right? So pick up a pair of NeoPixel rings and these costuming goggles and get to it! These goggles look a bit like aviator/welding goggle designs but are not for any sort of eye-protection! They are costume goggles only! You can wear them on top of your head or on your eyes but do not use for welding or flying or motorcycling, etc. The goggles are fully plastic...

$9.95

4 IN STOCK

EL wire starter pack - White 2.5 meter (8.2 ft)

PRODUCT ID: 546

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in White. 2.5 meters is...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in White. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change...

$19.95

IN STOCK

Maxbotix Ultrasonic Rangefinder - HRLV-EZ1 - HRLV-EZ1

PRODUCT ID: 984

The HRLV-MaxSonar-EZ sensor line is the most cost-effective solution for applications where precision range-finding, low-voltage operation, space...

The HRLV-MaxSonar-EZ sensor line is the most cost-effective solution for applications where precision range-finding, low-voltage operation, space saving, and low-cost are needed. The HRLV-MaxSonar-EZ sensor line provides high accuracy and high resolution ultrasonic proximity detection and ranging in air, in a package less than one cubic inch. This sensor line features 1mm resolution, target-size and operating-voltage compensation for improved...

$32.95

8 IN STOCK

Maxbotix Ultrasonic Rangefinder - HRLV-EZ0 - HRLV-EZ0

PRODUCT ID: 983

The HRLV-MaxSonar-EZ sensor line is the most cost-effective solution for applications where precision range-finding, low-voltage operation, space...

$33.95

37 IN STOCK

Small 1.2" 8x8 Ultra Bright Red LED Matrix - KWM-30881CVB

PRODUCT ID: 455

Make a scrolling sign, or a small video display with this 8x8 gridded red LED matrix. Only 1.2" on a side, it is quite visible but not so large...

Make a scrolling sign, or a small video display with this 8x8 gridded red LED matrix. Only 1.2" on a side, it is quite visible but not so large it won't plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. Since the display is in a grid, you'll need to 1:8 multiplex control it. We suggest either using a 74HC595...

$3.95

IN STOCK

Stainless Steel Conductive Ribbon - 5mm wide 1 meter long

PRODUCT ID: 1244

This woven conductive ribbon is great for powering lots of LEDs in a wearable project. It's thin, strong, smooth, and made completely of 316L...

This woven conductive ribbon is great for powering lots of LEDs in a wearable project. It's thin, strong, smooth, and made completely of 316L stainless steel. It plays nice with our stainless conductive thread and is very flexible, just like textile ribbon. The easiest way to attach this ribbon is to either slip it through a casing, or better yet, zig-zag stitch over it to tack it down. Because it is strong and flexible, its ideal for any...

$24.95

87 IN STOCK

Adafruit Small 1.2" 8x8 LED Matrix w/I2C Backpack - Yellow-Green

PRODUCT ID: 1051

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$10.95

IN STOCK

Miniature 8x8 Blue LED Matrix

PRODUCT ID: 956

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite...

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite sized! 64 bright blue LEDs are contained inside the plastic body, in an 8x8 matrix. There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space to wire it up Since the display is in a grid, you'll need to 1:8 multiplex control...

$5.95

IN STOCK

Lithium Ion Coin Cell Charger

PRODUCT ID: 1573

This is a special-purpose charger just for the rechargeable LIR2450 Lithium Ion coin cells. Slide the coin cell in the right way, and plug into any...

This is a special-purpose charger just for the rechargeable LIR2450 Lithium Ion coin cells. Slide the coin cell in the right way, and plug into any USB port to recharge - so easy! Takes about 3 hours to charge up, when its done, the green DONE LED will light up to let you know. Rechargeable coin cell is not included, but we have 'em in the shop here Charging is performed in three stages: first a preconditioning charge, then a...

$14.95

33 IN STOCK

1.2" 8x8 Matrix Square Pixel - White - KWM-R30881CWB-Y

PRODUCT ID: 1821

Make a scrolling sign, or a small video display with this 8x8 gridded pixel white LED matrix. Only 1.2" on a side, it is quite visible but not...

Make a scrolling sign, or a small video display with this 8x8 gridded pixel white LED matrix. Only 1.2" on a side, it is quite visible but not so large it won't plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. These LEDs have a bright white coloring, it's a beautiful shade but the process is...

$7.50

IN STOCK

Maxbotix Ultrasonic Rangefinder - LV-EZ3

PRODUCT ID: 981

LV-EZ3 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects...

LV-EZ3 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches out to 254-inches with 1-inch resolution. (Objects from 0 inches to 6-inches range as 6-inches.) The interface output formats included are pulse width output (PWM), analog voltage output (Vcc/512 volts per...

$24.95

37 IN STOCK

EL wire starter pack - Orange 2.5 meter (8.2 ft)

PRODUCT ID: 586

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Orange. 2.5 meters is...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Orange. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to...

$19.95

95 IN STOCK

Small 1.2" 8x8 Ultra Bright Square White LED Matrix + Backpack

PRODUCT ID: 1857

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's...

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can control a matrix for you but there's a lot of wiring to set up and they take up a ton of space. Here at Adafruit we feel your pain! After all, wouldn't it be awesome if you could control a matrix without tons of wiring?...

$13.50

IN STOCK

Maxbotix Ultrasonic Rangefinder - HRLV-EZ4 - HRLV-EZ4

PRODUCT ID: 985

The HRLV-MaxSonar-EZ sensor line is the most cost-effective solution for applications where precision range-finding, low-voltage operation, space...

$32.95

10 IN STOCK

High Brightness Pink Electroluminescent (EL) Wire - 2.5 meters - High brightness, long life

PRODUCT ID: 404

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You can make it look different colors by changing the coating, for example this is a vivid pink. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to...

$12.00

93 IN STOCK

Adafruit Small 1.2" 8x8 LED Matrix w/I2C Backpack - Yellow

PRODUCT ID: 1050

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$10.50

IN STOCK

Wire Light LED Strand - 12 Green LEDs + Coin Cell Holder

PRODUCT ID: 896

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated...

$4.95

OUT OF STOCK

Maxbotix Ultrasonic Rangefinder - HR-USB-EZ1 - MB1413

PRODUCT ID: 1343

The HRLV-MaxSonar-EZ sensor line is the fastest way to get precision range-finding into your computer. No microcontroller or adapter required, simply...

The HRLV-MaxSonar-EZ sensor line is the fastest way to get precision range-finding into your computer. No microcontroller or adapter required, simply connect any micro B USB cable (not included) into the sensor and install the FTDI drivers to get serial sonar distance data via serial on any computer operating system. The HR-USB-EZ sensor line provides high accuracy and high resolution ultrasonic proximity detection and ranging in air, in a...

$49.95

1 IN STOCK

Maxbotix Ultrasonic Rangefinder - LV-EZ2 - LV-EZ2

PRODUCT ID: 980

LV-EZ2 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects...

LV-EZ2 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6-inches out to 254-inches with 1-inch resolution. (Objects from 0 inches to 6-inches range as 6-inches.) The interface output formats included are pulse width output (PWM), analog voltage output (Vcc/512 volts per...

$24.95

31 IN STOCK

EL wire starter pack - Yellow 2.5 meter (8.2 ft)

PRODUCT ID: 585

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in yellow. 2.5 meters is...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in yellow. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to...

$19.95

98 IN STOCK

Small 1.2" 8x8 Ultra Bright Square Blue LED Matrix + Backpack

PRODUCT ID: 1853

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's...

$13.50

IN STOCK

Electroluminescent (EL) Tape/Strip Starter Pack - 100cm - White

PRODUCT ID: 635

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project,...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in White Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

$19.95

OUT OF STOCK

EL wire starter pack - Pink 2.5 meter (8.2 ft)

PRODUCT ID: 588

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Pink. 2.5 meters is...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Pink. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change...

$19.95

93 IN STOCK

Sewable Electroluminscent (EL) Wire Welted Piping- Aqua 5 meters

PRODUCT ID: 675

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC...

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. It looks a little like thin neon. Very bendable, it keeps its shape and you can curl it around your finger. Its an easy way to add some glow to a project, not as bright as LEDs but uses a lot less power! This particular model is standard...

$19.95

5 IN STOCK

Electroluminescent (EL) Tape/Strip Starter Pack - 100cm - Green

PRODUCT ID: 634

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project,...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Green Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

$19.95

12 IN STOCK

1.2" 8x8 Matrix Square Pixel - Amber - KWM-R30881CUAB

PRODUCT ID: 1818

Make a scrolling sign, or a small video display with this 8x8 gridded square Amber LED matrix. Only 1.2" on a side, it is quite visible but not...

Make a scrolling sign, or a small video display with this 8x8 gridded square Amber LED matrix. Only 1.2" on a side, it is quite visible but not so large it won't plug into a breadboard! 64 Amber LEDs are contained inside the plastic body, in an 8x8 matrix. There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. These LEDs have a deeper amber...

$4.50

IN STOCK

Electroluminescent (EL) Panel Starter Pack - 10cm x 10cm Aqua

PRODUCT ID: 627

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project,...

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project, even the batteries! Includes: 10cm x 10cm (approx 4"x4") square panel in AquaPortable 4xAAA inverter powerful enough to drive a single panel4 x AAA alkaline batteries to power the inverter and panel for 10 hours For more information and technical specifications, check the product links of...

$24.95

OUT OF STOCK

Adafruit Mini 0.8" 8x8 LED Matrix w/I2C Backpack - Pure Green

PRODUCT ID: 1633

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices...

$10.95

IN STOCK

Electroluminescent (EL) Tape/Strip Starter Pack - 100cm - Red

PRODUCT ID: 631

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project,...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Red Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each of...

$19.95

23 IN STOCK

Miniature 8x8 Yellow-Green LED Matrix

PRODUCT ID: 861

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite...

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite sized! 64 bright yellow-green LEDs are contained inside the plastic body, in an 8x8 matrix. There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space to wire it up Since the display is in a grid, you'll need to 1:8 multiplex...

$3.95

IN STOCK

Electroluminescent (EL) Tape/Strip Starter Pack - 100cm - Blue

PRODUCT ID: 633

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project,...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Blue Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

$19.95

18 IN STOCK

1.2" 8x8 Matrix Square Pixel - Yellow - KWM-R30881CUYB

PRODUCT ID: 1819

Make a scrolling sign, or a small video display with this 8x8 gridded yellow LED matrix. Only 1.2" on a side, it is quite visible but not so...

Make a scrolling sign, or a small video display with this 8x8 gridded yellow LED matrix. Only 1.2" on a side, it is quite visible but not so large it won't plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. These LEDs have a deeper yellow coloring, it's a beautiful shade but the process is different than our...

$4.50

IN STOCK

Small 1.2" 8x8 Ultra Bright Yellow-Orange LED Matrix - KWM-30881CUYB

PRODUCT ID: 1046

Make a scrolling sign, or a small video display with this 8x8 gridded yellow-orange LED matrix. Only 1.2" on a side, it is quite visible but not...

Make a scrolling sign, or a small video display with this 8x8 gridded yellow-orange LED matrix. Only 1.2" on a side, it is quite visible but not so large it won't plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. Since the display is in a grid, you'll need to 1:8 multiplex control it. We suggest either using...

$4.50

IN STOCK

Electroluminescent (EL) Tape/Strip Starter Pack - 100cm - Aqua

PRODUCT ID: 632

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project,...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Aqua Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

$19.95

OUT OF STOCK

Small 1.2" 8x8 Bright Square Pure Green LED Matrix + Backpack

PRODUCT ID: 1856

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's...

$10.95

IN STOCK

Electroluminescent (EL) Panel Starter Pack - 10cm x 10cm Blue

PRODUCT ID: 629

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project,...

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project, even the batteries! Includes: 10cm x 10cm (approx 4"x4") square panel in Blue Portable 4xAAA inverter powerful enough to drive a single panel 4 x AAA alkaline batteries to power the inverter and panel for 10 hours For more information and technical specifications, check the product links of...

$24.95

13 IN STOCK

Miniature 0.8" 8x8 Pure Green LED Matrix - KWM-20882CPGB

PRODUCT ID: 1624

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite...

You will squeak with delight when you hold this adorable miniature LED matrix. 0.8" square, its got everything a big LED matrix has, but bite sized! 64 pure green LEDs are contained inside the plastic body, in an 8x8 matrix. There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space to wire it up These LEDs have a deeper green coloring, its a beautiful shade but the...

$4.95

IN STOCK

Small 1.2" 8x8 Ultra Bright Square Amber LED Matrix + Backpack

PRODUCT ID: 1854

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's...

$10.50

IN STOCK

Small 1.2" 8x8 Ultra Bright Square Yellow LED Matrix + Backpack

PRODUCT ID: 1855

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's...

$10.50

IN STOCK

Small 1.2" 8x8 Ultra Bright Pure Green LED Matrix - KWM-30881CPGB

PRODUCT ID: 1623

Make a scrolling sign, or a small video display with this 8x8 gridded pure green LED matrix. Only 1.2" on a side, it is quite visible but not so...

Make a scrolling sign, or a small video display with this 8x8 gridded pure green LED matrix. Only 1.2" on a side, it is quite visible but not so large it wont plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. These LEDs have a deeper green coloring, its a beautiful shade but the process is different than our other...

$4.95

IN STOCK

Small 1.2" 8x8 Ultra Bright Yellow-Green LED Matrix - KWM-30881CUGB

PRODUCT ID: 1045

Make a scrolling sign, or a small video display with this 8x8 gridded yellow-green LED matrix. Only 1.2" on a side, it is quite visible but not...

Make a scrolling sign, or a small video display with this 8x8 gridded yellow-green LED matrix. Only 1.2" on a side, it is quite visible but not so large it wont plug into a breadboard! There are 16 pins on the side, 8 on each, with 0.1" spacing so you can easily plug it into a breadboard with one row on each side for wiring it up. Since the display is in a grid, you'll need to 1:8 multiplex control it. We suggest either using a...

$4.95

IN STOCK

EL wire welted piping starter pack - Aqua - 5 meters

PRODUCT ID: 676

A little bundle to get you started! This project pack contains: 5 meters (over 16 ft) of welted EL wire piping in Aqua. 5 meters is the maximum...

A little bundle to get you started! This project pack contains: 5 meters (over 16 ft) of welted EL wire piping in Aqua. 5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shink, both 1/8" and 1/4" for protecting the EL wire after soldering if you end up wanting to change the wire up 2...

$27.95

5 IN STOCK

Electroluminescent (EL) Tape/Strip Starter Pack - 100cm

PRODUCT ID: 637

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project,...

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Aqua Portable 4xAAA inverter powerful enough to drive a full meter of strip 4 x AAA alkaline batteries to power the inverter and tape for 10 hours For more information and technical specifications, check the product links of each...

EL wire starter pack - 2.5 meter (8.2 ft)

PRODUCT ID: 320

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire, the brightest and best...

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire, the brightest and best looking EL color we carry. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included) 2 inches of heat shrink, both 1/8" and 1/4" for protecting the EL wire after...

Silicone Cover Stranded-Core Wire - 26AWG in Various Colors

PRODUCT ID: 1970

Silicone-sheathing wire is super-flexible and soft, and it's also strong! Able to handle up to 200°C and up to 600V, it will do when PVC...

Silicone-sheathing wire is super-flexible and soft, and it's also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out. We like this wire for being extremely supple and flexible, so it is great for wearables or projects where the wire-harness has to be able to deal with a lot of bending. Comes with 2m of black, red, blue, green, grey, orange, or yellow wire. The wire is 26AWG stranded with an...

Electroluminescent (EL) Panel Starter Pack - 10cm x 10cm

PRODUCT ID: 639

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project,...

Get glowing in seconds with our Electroluminescent (EL) Panel Starter Pack! This pack contains everything you need for your first EL panel project, even the batteries! Includes: 10cm x 10cm (approx 4"x4") square panel in Aqua Portable 4xAAA inverter powerful enough to drive a single panel 4 x AAA alkaline batteries to power the inverter and panel for 10 hours For more information and technical specifications, check the product links of...

Adafruit Audio FX Sound Board + 2x2W Amp - WAV/OGG Trigger -16MB

PRODUCT ID: 2217

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use...

$29.95

15 IN STOCK

Adafruit Audio FX Sound Board + 2x2W Amp - WAV/OGG Trigger - 2MB

PRODUCT ID: 2210

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use...

$24.95

25 IN STOCK

Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H

PRODUCT ID: 3421

Listen to this good news - we now have a breakout board for a super tiny I2S MEMS microphone. Just like 'classic' electret microphones, MEMS...

Listen to this good news - we now have a breakout board for a super tiny I2S MEMS microphone. Just like 'classic' electret microphones, MEMS mics can detect sound and convert it to voltage, but they're way smaller and thinner. This microphone doesn't even have analog out, its purely digital. The I2S is a small, low cost MEMS mic with a range of about 50Hz - 15KHz, good for just about all general audio recording/detection. For...

$6.95

27 IN STOCK

Lithium Ion Polymer Battery with Short Cable - 3.7V 350mAh

PRODUCT ID: 4237

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 350mAh for a total of about 1.3 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection...

$5.95

IN STOCK

Adafruit MONSTER M4SK - DIY Electronic Eyes Mask

PRODUCT ID: 4343

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER...

Peep dis! Have you always wanted to have another pair of eyes on the back of your head? Or outfit your costume with big beautiful orbs? The MONSTER M4SK is like the Hallowing but twice as good, with two gorgeous 240x240 pixel IPS TFT displays, driven by a 120MHZ Cortex M4 processor that can pump out those pixels super fast. You'll get the same quality display as our Raspberry Pi Eyes kit but without needing to tote around a full Linux...

$44.95

OUT OF STOCK

Adafruit HalloWing M4 Express - ORANGE HALLOWEEN EDITION!

PRODUCT ID: 4300

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we...

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Following up on 2018's most-successful-skull-shaped development board, we UPPED our -skull-shaped development board game, and re-spinned (re-spun?) the HalloWing M0 into the HalloWing M4 with MORE of everything that makes this the spoooookiest dev board. New! For October 2019, we're got limited edition halloween-orange HallowingM4's - Same exact electronics and...

$39.95

IN STOCK

Adafruit VL53L0X Time of Flight Distance Sensor - ~30 to 1000mm

PRODUCT ID: 3317

The VL53L0X is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny invisible laser source,...

The VL53L0X is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny invisible laser source, and a matching sensor. The VL53L0X can detect the "time of flight", or how long the light has taken to bounce back to the sensor. Since it uses a very narrow light source, it is good for determining distance of only the surface directly in front of it. Unlike sonars that bounce ultrasonic...

$14.95

IN STOCK

Ultra Skinny NeoPixel 1515 LED Strip 4mm wide - 0.5 meter long - 75 LEDs

PRODUCT ID: 4368

We have all sorts of LED strips for a wide range of needs. Chonky strips? We got those! Strips with alligator clips that are easy-peasy to...

We have all sorts of LED strips for a wide range of needs. Chonky strips? We got those! Strips with alligator clips that are easy-peasy to MakeCode? Oh definitely. Weatherproof? We have a gamut of options. Now we have some Honey I Shrunk the LED Strips in the store. At an astonishing 4mm width these are wee yet surprisingly flexible and can fit just about anywhere. The wires are even nicely color-coded: black for ground, green for...

$24.95

OUT OF STOCK

Lithium Ion Polymer Battery Ideal For Feathers - 3.7V 400mAh

PRODUCT ID: 3898

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 400mAh for a total of about 1.9 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries. The batteries come pre-attached with a genuine 2-pin 25mm long JST-PH connector as shown and include the necessary...

$6.95

IN STOCK

Adafruit VL6180X Time of Flight Distance Ranging Sensor (VL6180)

PRODUCT ID: 3316

The VL6180X (sometimes called the VL6180 ) is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny laser...

The VL6180X (sometimes called the VL6180 ) is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny laser source, and a matching sensor. The VL6180X can detect the "time of flight", or how long the laser light has taken to bounce back to the sensor. Since it uses a very narrow light source, it is good for determining distance of only the surface directly in front of it. Unlike sonars that...

$13.95

IN STOCK

Adafruit LED Sequins - Multicolor Pack of 5

PRODUCT ID: 3377

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a...

$3.95

IN STOCK

Mini Oval Speaker with Short Wires - 8 Ohm 1 Watt

PRODUCT ID: 4227

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power....

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires with a connector on the end. It has a handy "Molex PicoBlade" 1.25mm pitch 2-pin cable, which makes plugging into a board easy. Or you can cut off the connector and just solder/clamp onto...

$1.95

IN STOCK

Adafruit I2S Stereo Decoder - UDA1334A Breakout

PRODUCT ID: 3678

This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface. It's affordable but sounds great! The...

This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface. It's affordable but sounds great! The NXP UDA1334A is a jack-of-all-I2S-trades: you can use 3.3V - 5V logic levels (a rarity), and can process multiple different formats by setting two pins to high or low. The DAC will process data immediately, and give you a clear, analog, stereo line level output. It's even cool with MCLK-less...

$6.95

IN STOCK

Adafruit HalloWing M0 Express

PRODUCT ID: 3900

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Are you the kind of person who doesn't like taking down the skeletons and...

This is Hallowing..this is Hallowing... Hallowing! Hallowing! Are you the kind of person who doesn't like taking down the skeletons and spiders until after January? Well, we've got the development board for you. This is electronics at its most spooky! The Adafruit HalloWing is a skull-shaped ATSAMD21 board with a ton of extras built in to make for an adorable wearable, badge, development kit, or the engine...

$34.95

53 IN STOCK

Adafruit Animated Eyes Bonnet for Raspberry Pi Pack - Pi not included

PRODUCT ID: 3813

Give your next animatronic or robotic project the gift of eyes with this Snake Eyes Bonnet Pack for Raspberry Pi . The Snake Eyes bonnet is an...

Give your next animatronic or robotic project the gift of eyes with this Snake Eyes Bonnet Pack for Raspberry Pi . The Snake Eyes bonnet is an accessory for driving TFT LCD displays, and it also provides four analog inputs for sensors. It's perfect for making cosplay masks, props, spooky sculptures for halloween, animatronics, robots...anything where you want to add a pair of animated eyes! We recently added some very...

$49.95

OUT OF STOCK

Clear Acrylics and Hardware Kit for Monster M4sk

PRODUCT ID: 4330

Here is the perfect kit for mounting convex lenses (glass or plastic) to your Monster M4sk! These acrylics has been laser-cut...

Here is the perfect kit for mounting convex lenses (glass or plastic) to your Monster M4sk! These acrylics has been laser-cut specifically for lenses with a lip-edge, so we can't guarantee it'll fit with any ol' convex lens. But it does work great with ours. And of course, the mounting hardware is included, so you can snap it right onto your M4SK. Takes less than five minutes to assemble, you just need a...

$3.50

62 IN STOCK

Mini External USB Stereo Speaker

PRODUCT ID: 3369

Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker . It's USB-only and does not require or use a...

Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker . It's USB-only and does not require or use a 3.5mm audio jack. You'll get great audio, even with a device that doesn't have a head phone jack. And since it is powered over USB, there's no need to charge it by other means, merely plug it into your desired device's USB port and listen to the audio flow. Compact and convenient to...

$12.50

IN STOCK

Clear Acrylic Lens Holder + Hardware Kit for HalloWing

PRODUCT ID: 4013

Here is the perfect kit for mounting a convex lens (glass or plastic) to your HalloWing! This holder has been laser-cut specifically for lenses with...

Here is the perfect kit for mounting a convex lens (glass or plastic) to your HalloWing! This holder has been laser-cut specifically for lenses with a lip-edge, so we can't guarantee it'll fit with any ol' convex lens. But it does work great with ours. And of course, the mounting hardware is included so you can snap it right onto your HalloWing. Takes less than five minutes to assemble, you just need a screwdriver. Please note: It...

$2.95

IN STOCK

EVA Foam Pack in Rainbow Colors - 2mm thick - 10 sheets

PRODUCT ID: 4349

EVA foam is one of the best and easiest go-to materials for constructing costumes and props. It's light, inexpensive, versatile, and can easily...

EVA foam is one of the best and easiest go-to materials for constructing costumes and props. It's light, inexpensive, versatile, and can easily be cut and heat-shaped for a snug fit. With enough time, patience, and the right tools, EVA foam can be finished to look like nearly any material. Use to create costume armor, headpieces, prop weapons, and other accessories. These sheets are just under 2mm in thickness and come in 10 colors:...

$7.95

61 IN STOCK

Lithium Ion Polymer Battery with Short Cable - 3.7V 420mAh

PRODUCT ID: 4236

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when...

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 420mAh for a total of about 1.55 Wh. If you need a larger (or smaller!) battery, we have a full range of LiPoly batteries The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection...

$6.95

IN STOCK

Large Liquid Crystal Light Valve - Controllable Shutter Glass

PRODUCT ID: 3330

What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a...

What do you get when you power a layer of liquid crystal material sandwiched between two sheets of glass? A Liquid Crystal Light Valve (a.k.a a LCD Controllable Black-out Panel)! They're often used for electric welding helmets because they can protect the welder's eyes from the bright sparks. Or – if you aren't a welder – they can be used to provide a "reveal" effect for your...

$7.50

IN STOCK

Micro Servo Arm and Horn Set

PRODUCT ID: 4251

If you bought a servo from us you probably got a bunch of plastic add-ons that you can snap onto the rotating part of the servo. These are called...

If you bought a servo from us you probably got a bunch of plastic add-ons that you can snap onto the rotating part of the servo. These are called 'servo horns'. For many robotics projects you'll end up drilling or gluing to the horns to attach it to your armatures. But maybe you messed up, or you want to recycle the expensive motor part? This product comes with just the horns! No servo is included, so you can reuse the motors...

$1.25

IN STOCK

4 x AA Battery Holder with Premium Jumper Header Wires

PRODUCT ID: 3859

We've got battery holders for all sorts of needs and projects! Waterproof? Here ya go. With an on/off switch? Easy peasy. Here's our latest...

We've got battery holders for all sorts of needs and projects! Waterproof? Here ya go. With an on/off switch? Easy peasy. Here's our latest addition in classy Adafruit black: 4 x AA Battery Holder with Premium Header Wires . What's so special about 'em? Well you can plug them right into a breadboard! No need to fight with those skinny stripped wires you normally get. Of course, you can always still solder them into a PCB. 4 x AA...

$2.95

86 IN STOCK

Adafruit MetroX Classic Kit - Experimentation Kit for Metro 328

PRODUCT ID: 3588

Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete...

Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete over 20 different circuit and projects. Basically everything you need to be playing within minutes of its arrival. No soldering required, works with Mac, Windows and Linux! This item is the same exact kit as https://www.adafruit.com/product/170 This pack includes the Adafruit Metro. METRO is the...

$84.95

OUT OF STOCK

Side-light Fiber Optic Tube - 4mm Diameter - 1 meter long

PRODUCT ID: 4163

Yay, a plastic tube! No, we jest. This is no ordinary plastic tube, but rather a side-lighting fiber optic tube. This is a pretty neat way to glow...

Yay, a plastic tube! No, we jest. This is no ordinary plastic tube, but rather a side-lighting fiber optic tube. This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have...

$7.50

OUT OF STOCK

Side-light Fiber Optic Tube - 5mm Diameter - 1 meter long

PRODUCT ID: 4164

Yay, a plastic tube! No, we jest. This is no ordinary plastic tube, but rather a side-lighting fiber optic tube. This is a pretty neat way to glow...

$7.50

OUT OF STOCK

Silver Pin Back with Foam Adhesive

PRODUCT ID: 2838

This little Silver-color Pin with Foam Adhesive is the perfect way to attach any PCB or small component to cloth material. The adhesive forms a...

This little Silver-color Pin with Foam Adhesive is the perfect way to attach any PCB or small component to cloth material. The adhesive forms a solid but not permanent bond for a strong reliable hold. The pin also has a handy little locking mechanism to keep the pin from unlatching from friction. If you are working with wearables be sure to keep a handful of these around - they pair especially well with the Flora, Gemma, and Circuit...

$0.45

IN STOCK

Standard Servo Arm and Horn Set - 25 Spline

PRODUCT ID: 4250

If you bought a servo from us you probably got a bunch of plastic add-ons that you can snap onto the rotating part of the servo. These are called...

$2.50

64 IN STOCK

Fiber Optic Light Source - 1 Watt - Red

PRODUCT ID: 4165

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded...

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded plastic, a principle called "total internal reflection" (which also kinda sounds like a very expensive meditation island retreat). When the light pipe doesn't have total reflection, you can get a nifty lighting effect from the light illuminating the plastic tubing. All you need...

$6.95

98 IN STOCK

Fiber Optic Light Source - 1 Watt - White

PRODUCT ID: 4168

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded...

$6.95

38 IN STOCK

Adafruit NeoPixel UV LED Strip with 32 LED/m - White PCB - 1M

PRODUCT ID: 3851

What new iteration of NeoPixel strip is this? Roll out the black light and disco ball! It's an Adafruit NeoPixel Ultraviolet Strip...

What new iteration of NeoPixel strip is this? Roll out the black light and disco ball! It's an Adafruit NeoPixel Ultraviolet Strip with 32 LEDs per meter ! Each order comes as a single one meter long strip. If you order multiple meters, you'll get that many individual 1 meter pieces. The strip is made of flexible PCB material, and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters....

$24.95

60 IN STOCK

Fiber Optic Light Source - 1 Watt - Blue

PRODUCT ID: 4167

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded...

$6.95

85 IN STOCK

Circuit Playground Snow Globe Kit

PRODUCT ID: 4011

Light up the winter nights this year with an electronic Snow Globe! This kit provides everything you need to make your very own, no soldering...

Light up the winter nights this year with an electronic Snow Globe! This kit provides everything you need to make your very own, no soldering required! You can use MakeCode to program various light and sound effects into the Circuit Playground Express. MakeCode uses easy-to-understand drag and drop programming blocks, so even if you've never programmed before, you'll be rockin' like the Rockettes. Check out the many electronic snow...

$39.95

OUT OF STOCK

Fiber Optic Light Source - 1 Watt - Green

PRODUCT ID: 4166

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded...

$6.95

IN STOCK

Adafruit + Cartoon Network Cosplay "The Works" Kit

PRODUCT ID: 4359

Are you a super Cartoon Network fan and interested in making cosplay and Halloween projects with a Circuit Playground Express, but...

Are you a super Cartoon Network fan and interested in making cosplay and Halloween projects with a Circuit Playground Express, but overwhelmed with what to buy? Here's a huge kit to get started, no matter your skill level. This kit includes beautiful and colorful programmable NeoPixel LEDs to glow up (a Circuit Playground Express and a NeoPixel strip), conductive nylon tape, supplies to attach it...

$59.95

OUT OF STOCK

Nth-Light Narrow LED Flexible Strip Light

PRODUCT ID: 3683

Here at Adafruit we never get tired of new and exotic glowing things. Like moths to the flame, we were intrigued by this new LED technology from Nth...

Here at Adafruit we never get tired of new and exotic glowing things. Like moths to the flame, we were intrigued by this new LED technology from Nth Light. Instead of having individual LEDs, Nth prints micro LED diodes onto a flexible plastic substrate for a unique look. The Nth-Light Narrow LED Flexible Strip Light is printed in three basic processes, starting with standard LED wafers. These wafers are then cut into micro LEDs the...

$18.50

50 IN STOCK

Fiber Optic Light Source - 1 Watt - Pink

PRODUCT ID: 4169

This is a pretty neat way to glow up. Light in the fiber optic cable zooms through the core by constantly bouncing off of the edge of the molded...

$6.95

42 IN STOCK

Adafruit + Cartoon Network Cosplay Basics Kit

PRODUCT ID: 4358

Are you interested in making cosplay and Halloween projects with a Circuit Playground Express, but overwhelmed with what to buy? Better...

Are you interested in making cosplay and Halloween projects with a Circuit Playground Express, but overwhelmed with what to buy? Better yet, do you love Cartoon Network characters and shows? Here's a intermediary pack to get started, no matter your skill level. This kit includes beautiful and colorful programmable NeoPixel LEDs to glow up (a Circuit Playground Express and a NeoPixel strip), conductive...

$49.95

3 IN STOCK

Adafruit + Cartoon Network Cosplay Introductory Kit

PRODUCT ID: 4355

Are you interested in making cosplay and Halloween projects with a Circuit Playground Express, but overwhelmed with what to buy? Better...

Are you interested in making cosplay and Halloween projects with a Circuit Playground Express, but overwhelmed with what to buy? Better yet, do you love Cartoon Network characters and shows? Here's a beginner pack to get started, no matter your skill level. This kit includes beautiful and colorful programmable NeoPixel LEDs to glow up (a Circuit Playground Express and a NeoPixel strip) and a AAA battery...

$39.95

3 IN STOCK

Fluorescent Pigments in Various Colors

PRODUCT ID: 4246

We're with the squad back at New York's hottest cyberpunk club, Near Field Commune(ication), and it's still got ...

We're with the squad back at New York's hottest cyberpunk club, Near Field Commune(ication), and it's still got everything , Adabot & the Circuit Playground, Collin's wondrous, mind-blowing, heart-stirring Pulse Room, and more! And you are dressed to the cyber-nine's, with wearable LEDs, EL tape, a full set of glittering RFID/NFC Nail Stickers, and some...

Flexible Silicone Neon-Like LED Strip in Various Colors - 1 Meter

PRODUCT ID: 3902

Here at Adafruit we love discovering new and exotic glowing things. Like moths to the flame, we were intrigued by these fresh Flexible Silicone...

Here at Adafruit we love discovering new and exotic glowing things. Like moths to the flame, we were intrigued by these fresh Flexible Silicone Neon-Like LED Strips ! They look a lot like neon, but without the need for expensive transformers, glass tubing or inert gasses. Super flexible and bendy, they feature a single-color non-addressable LED strip with a solid chunk of translucent silicone rubber as a diffuser. They look incredible, and...

Litex Spare Battery Case

PRODUCT ID: 1355

This is a little battery pack for our Litex LED ribbons. No LEDs are included, but the battery pack is very nice and you can cut the LED ribbon in...

This is a little battery pack for our Litex LED ribbons. No LEDs are included, but the battery pack is very nice and you can cut the LED ribbon in half and then use the extra battery pack to power the excess. Comes with two CR1220 batteries, we also carry extras if you need them! Litex Spare Battery Case (4:55) Note: Battery case may come grey or black

$4.95

7 IN STOCK

Cosplay World by Brian Ashcraft and Luke Plunkett

PRODUCT ID: 2224

Cosplay World is filled with striking images of costume play from around the world. This definitive look at the global phenomenon...

Cosplay World is filled with striking images of costume play from around the world. This definitive look at the global phenomenon known as “cosplay” examines its evolution from the fringes of society to the spotlight of modern culture. For over 100 years, men and women around the world have been dressing up as their favorite characters from movies, games, comics, TV, and books. Beginning as a curiosity and hobby for...

$29.95

4 IN STOCK

Bluefruit LE - Bluetooth Low Energy (BLE 4.0) - nRF8001 Breakout - v1.0

PRODUCT ID: 1697

Our Adafruit Bluefruit LE (Bluetooth Smart, Bluetooth Low Energy, Bluetooth 4.0) nRF8001 Breakout allows you to establish an easy to use wireless...

Our Adafruit Bluefruit LE (Bluetooth Smart, Bluetooth Low Energy, Bluetooth 4.0) nRF8001 Breakout allows you to establish an easy to use wireless link between your Arduino and any compatible iOS or Android (4.3+) device. It works by simulating a UART device beneath the surface, sending ASCII data back and forth between the devices, letting you decide what data to send and what to do with it on either end of the connection. Unlike classic...

DISCONTINUED

Adafruit HUZZAH CC3000 WiFi Shield with Onboard Antenna

PRODUCT ID: 1491

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow,...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from creating or developing a WiFi Arduino shield. NO LONGER! The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for communication (not...

DISCONTINUED

Adafruit HUZZAH CC3000 WiFi Breakout with Onboard Antenna - v1.1

PRODUCT ID: 1469

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow,...

For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too large. So we shied away from carrying any general purpose microcontroller-friendly WiFi boards. NO LONGER! The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for...

DISCONTINUED

XBee Module - Series 1 - 1mW with Wire Antenna - XB24-AWI-001

PRODUCT ID: 128

This is our most popular XBee wireless module: the series 1 802.15.4 protocol 1mW with wire antenna. Its good for point-to-point, multipoint and...

This is our most popular XBee wireless module: the series 1 802.15.4 protocol 1mW with wire antenna. Its good for point-to-point, multipoint and convertible to a mesh network point. We suggest this module for those starting out as it is the easiest to get going: if there are two XBees in the same area they will automatically 'sync' and pass serial data back and forth without any additional work or configuration What we like about the...

DISCONTINUED

Arduino Starter Kit from Arduino.cc

PRODUCT ID: 1078

The Arduino starter kit provides an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It contains...

The Arduino starter kit provides an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It contains all of the essential components required to start programming with the Arduino Uno board, and a guidebook featuring 15 different projects, which are designed to evolve the user from beginner to professional level. The starter kit has been developed together with a series of ten video tutorials hosted...

DISCONTINUED

FLORA Sensor Pack

PRODUCT ID: 1458

Sense the world around you! The FLORA Sensor Pack includes many types of sensors for your wearable enjoyment. Sense motion, direction, color, light...

Sense the world around you! The FLORA Sensor Pack includes many types of sensors for your wearable enjoyment. Sense motion, direction, color, light levels, touch, and connections with FLORA sensor breakouts and conductive materials, and a few NeoPixels for experimenting with displaying your sensor information. Take your project portable with the included battery pack and stitch it into a final design with conductive thread. $100 worth of goodies...

DISCONTINUED

Conductive thread ribbon cable - White - 1 yard

PRODUCT ID: 1139

This lightweight, flexible fabric ribbon cable contains four channels of conductive thread, perfect for wiring up wearables where flexibility is key....

This lightweight, flexible fabric ribbon cable contains four channels of conductive thread, perfect for wiring up wearables where flexibility is key. Use it to connect your conductive fabric gamepad to your microcontroller or computer! Features: Low resistance: ~16 Ω / ft. [304.80 mm]4 Conductor connectionsPower and data applicationsLight-weightSewableWashable and dryableStitchable over apparel construction seamsFoldable onto itself...

DISCONTINUED

DIY Sensor Film Kit - 4x6" Small Kit

PRODUCT ID: 1917

The Sensor Film Kit is a great new way to make custom-sized sensors out of force sensitive material. This kit includes one piece of black plastic...

The Sensor Film Kit is a great new way to make custom-sized sensors out of force sensitive material. This kit includes one piece of black plastic sensor film (it's thicker and more durable than Velostat but similar in function), two pieces of heavy aluminum foil, and two pieces of clear adhesive polyester film. The sensor film is super durable and changes its electrical resistance when force is applied. It's a lot like Velostat but a bit...

DISCONTINUED

Raspberry Pi Model B starter pack Doesn't include Raspberry Pi 1

PRODUCT ID: 955

You want to get hacking with your Pi fast, right? Get everything you need to start with the Adafruit Starter Pack for Raspberry Pi. It's the...

You want to get hacking with your Pi fast, right? Get everything you need to start with the Adafruit Starter Pack for Raspberry Pi. It's the perfect accompaniment to your new Pi, everything you need to get a distro image loaded and running. We even pre-assemble the Cobbler for you, no soldering required. THIS PACK DOES NOT INCLUDE A RASPBERRY PI 1 MODEL B . To purchase a Starter Pack with an included Raspberry Pi Model B Revision 1.0, code...

DISCONTINUED

Cirrus Logic Audio Card

PRODUCT ID: 1761

Unleash the audio capabilities of your Raspberry Pi! The Cirrus Logic Audio Card , produced by Element14 in collaboration with Cirrus Logic, offers...

Unleash the audio capabilities of your Raspberry Pi! The Cirrus Logic Audio Card , produced by Element14 in collaboration with Cirrus Logic, offers Raspberry Pi® users similar flexibility to a PC sound-card to capture audio alongside their camera, and experiment with stereo digital capture and playback. The Cirrus Logic audio board adds a powerful class D amplifier to the Raspberry Pi. The audio board adds inputs for SPDIF, Line in and...

DISCONTINUED

Litex White LEDs on Black Fabric Ribbon Pack - 1.5 meter 20 LEDs

PRODUCT ID: 1397

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 1.5 meters long, and has 20 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

DISCONTINUED

Arduino Leonardo ATmega32u4 without headers

PRODUCT ID: 883

Note: This product is discontinued, but you can purchase the Seeeduino Lite, which is an equivalent alternative that can be used instead. The...

Note: This product is discontinued, but you can purchase the Seeeduino Lite, which is an equivalent alternative that can be used instead. The latest addition to the Arduino family is here! The Arduino Leonardo is a microcontroller board based on the exciting USB-enabled ATmega32u4 (datasheet). This chip has about the same amount of flash, RAM and capability as the ATmega328 found in the UNO. It has 20 digital input/output pins (of which 7...

DISCONTINUED

Octolively Kit - Warm White - Tileable Interactive LEDs

PRODUCT ID: 729

Octolively modules are tileable, digital interactive LED surfaces filled with ultrabright LEDs that respond in complex and gentle ways to stimulus...

Octolively modules are tileable, digital interactive LED surfaces filled with ultrabright LEDs that respond in complex and gentle ways to stimulus provided by human interaction. Each Octolively module is 4 X 8 inches (10.16 X 20.32 cm) in size, and features eight huge (10 mm) ultrabright LEDs, spaced along a two-inch grid. Each Octolively module also has eight infrared proximity sensors-- one for every LED --to detect nearby motion, even in...

DISCONTINUED

Litex White LEDs on White Fabric Ribbon Pack - 1.5 meter 30 LEDs

PRODUCT ID: 1398

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 1.5 meters long, and has 30 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

DISCONTINUED

Litex White LEDs on Black Fabric Ribbon Pack

PRODUCT ID: 1353

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 21"/53cm long, and has 10 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

DISCONTINUED

Punk LED Collar Kit - Red LEDs

PRODUCT ID: 1454

Make your own studded choker with an LED twist! This kit of parts comes with all the materials you'll need for a punk style LED collar. Ten juicy...

Make your own studded choker with an LED twist! This kit of parts comes with all the materials you'll need for a punk style LED collar. Ten juicy diffused red LEDs adorn a high-quality black leather collar that fits necks 12-15 inches (30 to 38 centimeters). Attach the included battery holder and potentiometer, used to adjust the brightness of the LEDs. The simple circuit is powered by a single CR2032 battery (we provide an extra for maximum...

DISCONTINUED

Litex White LEDs on White Fabric Ribbon Pack - 21" 10 LEDs

PRODUCT ID: 1354

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller...

This soft fabric ribbon has tiny surface mount LEDs bonded onto two thin conductive threads that go along the length. A tiny battery pack controller snaps onto the end. The result is an ultra-flexible and elegant-looking way to add LEDs to a wearable project. This ribbon is approximately 21"/53cm long, and has 10 white LEDs spaced equally along the ribbon. You can cut the ribbon easily but you cannot solder to it so once it's cut, it...

DISCONTINUED

1,000 Incredible Costume & Cosplay Ideas

PRODUCT ID: 2208

1,000 Incredible Costume and Cosplay Ideas provides a broad and detailed glimpse into the ingenious artistry and attention to detail behind some...

1,000 Incredible Costume and Cosplay Ideas provides a broad and detailed glimpse into the ingenious artistry and attention to detail behind some of the most fabulous costumes you can find. Featuring costumes from popular convention-goers to professional craftsman, this stunning, photo-filled book by Joey Marsocci and Allison DeBlasio of Dr. Grymm Laboratories walks you through scads of your favorite characters as imagined and created by...

DISCONTINUED

Lithium Ion Rechargable Coin Cell Battery - LIR2450

PRODUCT ID: 1572

You can swap a coin-cell powered design that uses one-use Lithium 2450 cells for this rechargeable cell. This battery is like a little Lithium Ion...

You can swap a coin-cell powered design that uses one-use Lithium 2450 cells for this rechargeable cell. This battery is like a little Lithium Ion battery, but in coin cell shape. It doesn't have a huge capacity, only about 120mAh, compared to the 600mAh common to primary non-rechargeable cells. There are a few things to watch out for when using these batteries: These cells do not have protection circuitry built in, so use only the charger...

DISCONTINUED

Arduino Micro without Headers - 5V 16MHz ATmega32u4 - Assembled

PRODUCT ID: 1315

Squee! It's the cutest, tiniest little Arduino yet! The Arduino Micro packs all of the power of the Arduino Leonardo in a 1.9" x 0.7"...

Squee! It's the cutest, tiniest little Arduino yet! The Arduino Micro packs all of the power of the Arduino Leonardo in a 1.9" x 0.7" (48mm x 18mm) size. Although it may look like a stick of gum, its actually a USB-native 8-bit microcontroller, with 32K of flash, and 2.5K of RAM. You can program it directly via the USB micro connector on one end (or for the advanced users, the 6-pin ISP header). The Arduino Micro is a...

DISCONTINUED

Sugru - multicolor pack

PRODUCT ID: 436

Sugru! Soft-touch silicone rubber that molds and sets permanently. Sticks to aluminum, steel, ceramics, glass, wood and some fabrics + plastics!...

DISCONTINUED

Adafruit #ElectronicHalloween Halloween Cards (set of 5)

PRODUCT ID: 3912

"I prefer winter and fall, when you feel the bone structure of the landscape. Something waits beneath it; the whole story doesn't...

"I prefer winter and fall, when you feel the bone structure of the landscape. Something waits beneath it; the whole story doesn't show." – Andrew Wyeth There's something about a Halloween landscape that immediately takes us back to childhood trick-or-treating and homemade costumes. Here's a special Adafruit set of five beautiful Halloween Cards that evoke the spirit of the season, from pumpkins to graveyards to a...

DISCONTINUED

AdaBox009 - HalloWing

PRODUCT ID: 3956

Are you the kind of person who doesn't like taking down the skeletons and spiders until after January? Well, we've got the ADABOX for you....

Are you the kind of person who doesn't like taking down the skeletons and spiders until after January? Well, we've got the ADABOX for you. This is electronics at its most spooky! ADABOX 009 is Halloween themed, for all of us who love scares, costumes, and (of course!) candy . OK, so we didn't fill this ADABOX with candy corn, but we did curate a collection of inspiring electronics to make your Halloween more...

DISCONTINUED