A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit ! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what  normally  would go out the HDMI port come up on a nice little flat screen. * Its not technically a HAT due to the lack of an on-board EEPROM, but its the...

"These go to eleven."  11 millimeters that is! Our  Black Plated M/F Brass Standoffs  are engineered specifically to keep your Pi HAT snug on your Pi while also keeping the two boards separated, in particular the HDMI port. These standoffs can also be screwed into each other allowing stacking multiple HATs on to one Pi! They're the perfect companion for any Pi Hat combo. Each order comes with two...

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Raspberry Pi and motors are not included. Works with any and all Raspberry Pi computers with 2x20 connection port. Since the Raspberry Pi does not have a lot of PWM pins, we use a  fully-dedicated PWM driver chip  ...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2 or Pi 3 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the...

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model Pi 3, Pi Zero, A+, B+, or Pi 2 & 3 Here's the low-down on the GPS module: -165 dBm sensitivity, 10 Hz updates, 66 channelsOnly 20mA current drawBuilt in Real Time Clock (RTC) - slot in a CR1220 backup...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. For use...

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our  Black Plated M/F Brass 16mm Standoffs  are engineered specifically to keep your PiTFT or other Pi accessories with extra tall headers properly secured while also keeping the two boards separated. These standoffs can also be screwed into each other just like the 11mm versions (made for PiHATs). Each order comes with two standoffs and two hex...

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero with the  Zero4U ! This is a 4-port USB hub for Raspberry Pi Zero, and it can be mounted back-to-back onto a Pi Zero. The 4 pogo pins on the back will connect the PP1, PP6, PP22 and PP23 testing pads on your Raspberry Pi Zero – no soldering required! This item can only work with the Zero W if a ferrite ring is...

Design your own Bonnet or pHAT, attach custom circuitry and otherwise dress your Pi Zero with this jaunty prototyping Bonnet kit! To add to the Adafruit Bonnet party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with...

You can now create a dazzling display with your Raspberry Pi Model Zero/A+/B+/Pi 2 or Pi 3 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. This HAT is our finest to date, full of some really great circuitry. Let me break it down for you: Simple design  - plug in power, plug in...

You can now create a dazzling display with your Raspberry Pi with the Adafruit RGB Matrix Bonnet. These boards plug into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. "Bonnet" boards work on any Raspberry Pi with a 40-pin GPIO header — Zero, Zero W/WH, Model A+, B+, Pi 2 and Pi 3. They do not work with...

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for both! Simply attach the standoffs in the four corners of the HAT, then connect to the 40-pin header. Once the HAT is connected, you can power your Pi through the RJ-45 network connector. Compatible only with Raspberry Pi 3 B+ that has PoE pins For people with non-Pi 3 B+'s, or if you can't use...

The Raspberry Pi is an amazing single board computer - and one of the best parts is that GPIO connector! 40 pins of digital goodness you can twiddle to control LEDs, sensors, buttons, radios, displays - just about any device you can imagine. This Adafruit GPIO Expander Bonnet will give you even more digital deliciousness - 16 more digital input/output pins are yours for any desire you have. The outputs are grouped into two 16-pin connectors that...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy bonnet! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. For use...

Hey Mr. DJ! Turn up that Raspberry Pi mix to the  max  with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi . (It's not big enough to be an official HAT, so we called it a bonnet, you see?) It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi computers with a 2x20 connector - A+, B+, Zero, Pi 2, Pi 3, etc. We've tested it out with Raspbian (the official operating system) and...

Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in a robot rebellion. Why even go down that path? Here at Adafruit, we believe in making robots our  friends! So if you find yourself wanting a companion, consider the robot. They're fun to program, and you can get creative with decorations. With that in mind, we designed the Adafruit Crickit HAT -...

For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's harder to use than the Thru-Hole type headers, but for the slickest, slimmest fit, this header is recommended!

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing works by detecting when a person (or animal) has touched one of the sensor electrodes. Capacitive touch sensing used for stuff like touch-reactive tablets and phones, as well as control panels for appliances, which is where you may have used it before. This HAT allows you to create electronics that can...

The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top of your Model A+ or B+ and fits into our case quite nicely. It's designed to plug directly onto the...

When your Raspberry Pi project requires multiple power supplies, why not check out the new Zero2Go Omini ? This multi-input power supply buck-boost converter fits on top of a Raspberry Pi (any sort!) and lets you power it with up to 3 different input ports, so you can keep powered no matter what your battery or power plug situation. Note that although it has the name 'Zero' it can be used by any Raspberry Pi computer with a 2x20...

If you'd like a compact display, with buttons and a joystick - we've got what you're looking for. The Adafruit 128x64 OLED Bonnet for Raspberry Pi is the big sister to our mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger screen besides. With the OLED display in the center, we had some space on either side so we added a 5-way joystick and two pushbuttons. Great for when you want to have a...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Raspberry Pi with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards with which...

Pocket-sized fun is the name of this game, with the Joy Bonnet  – our most fun Bonnet ever (no we didn't even think that was possible, either!). This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you install our script onto your Pi, the controls will act like a keyboard, for easy use with any emulator or media player. Personally, we found this Bonnet...

Control the same hardware as used in space...build your very own Astro Pi with the new Raspberry Pi Sense HAT ! The Raspberry Pi Sense HAT is attached on top of the Raspberry Pi via the 40 GPIO pins to create an ‘Astro Pi’. The Sense HAT has several integrated circuit based sensors can be used for many different types of experiments, applications, and even games. And it's being used in conjunction with the Raspberry Pi Foundation...

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi  with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry PiMini proto area for adding componentsAdd standard male or female headers for breadboard like functionalityPower (both 5V and 3.3V) as well as ground connections...

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero, or any other single-board computer with the  Zero4U ! This is a 4-port USB 2.0 hub, almost identical to this one, but without the ferrite bead, standoffs or pogo pins . This might be a preferable format if you want to mount it on the bottom or side-by-side or with another HAT below it. It's also great as-is as a small USB...

Give your next animatronic or robotic project the gift of eyes with this Snake Eyes Bonnet Pack for Raspberry Pi . The Snake Eyes bonnet is an accessory for driving TFT LCD displays, and it also provides four analog inputs for sensors. It's perfect for making cosplay masks, props, spooky sculptures for halloween, animatronics, robots...anything where you want to add a pair of animated eyes! We recently added some very...

Ideal for monitoring conditions in your house, garage, and more, the Pimoroni  Enviro pHAT packs 4 different sensors, letting you measure temperature, pressure, light level, color, 3-axis motion, compass heading, and analog inputs. That's up to 10 different variables! Snap it   on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a comprehensive environment-sensing pHAT powered directly from the Pi....

Pimoroni's Pico HAT Hacker gives you full access to all 40 pins on your Pi, broken out at the top. It's a super-skinny 0.8mm PCB, so you can solder it right onto the pins on your Pi and still have enough height on a standard header to fit a HAT or pHAT on top. There are handy labels for all of the pins, with BCM pin numbering on one side, and more descriptive labels on the other to show where the I2C, UART, SPI, PWM, and I2S pins...

Add some easy-listenin' tunes to your Raspberry Pi using this basic audio bonnet. It'll give you stereo line out from a digital I2S converter for a good price, and sounds nice to boot! This bonnet features the UDA1334A I2S Stereo DAC, a perfect match for any I2S-output audio interface. It's affordable but sounds great - music to our ears. It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi...

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Take control of and monitor your world with Pimoroni's Automation HAT  -- an ultimate jack-of-all-trades Raspberry Pi HAT! With relays, analog channels, powered outputs, and buffered inputs (all 24V tolerant), this home monitoring and automation controller allows you to hook up a plethora of goodies to...

A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit ! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what  normally  would go out the HDMI port come up on a nice little flat screen. * Its not technically a HAT due to the lack of an on-board EEPROM, but its the...

Here at Adafruit we never tire of cool, new displays, so these super sweet tri-color e-paper displays really caught our eye! Pimoroni's Inky pHat is a petite 212x104 pixel three-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the 3-second display-change-cycle....

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little pHAT. It's the neatest way to add audio to your Pi project, and its beautiful artwork evokes an 80s boombox! Pimoroni isn't claiming audiophile sound quality, but it's perfect for fun little projects where you want to add sound output – speech, notification sounds, or light...

Is this not the cutest little display for the Raspberry Pi? It features a 2.4" display with 320x240 16-bit color pixels and a resistive touch overlay. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! It's designed to fit nicely onto the Pi Model Zero, A+, B+, Pi 2, Pi 3 - any Pi with a 2x20 connector. This...

If music be the food of love, play on. But make sure you use this super little pHAT DAC to get the best out of your Raspberry Pi audio! The pHAT DAC provides a super affordable high-quality DAC for the Raspberry Pi. Pumping out 24-bits at 192KHz of audio goodness from the Raspberry Pi's I2S interface on the 2x20 pin GPIO header. Since it's digital audio, it sounds really good, much better than the onboard analog audio. The 3.5mm...

Do you need a solution for home automation, hydroponics, light industrial automation, and other related predicaments? Pimoroni's Automation pHAT  – the little sibling of the Automation HAT – is the most compact way to take control of and monitor your world! Pimoroni has pulled together a great set of features into this home monitoring and automation controller. With a relay, analog channels, powered...

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic paper displays to 4.2" glorious inches! Say hellooo to Inky wHAT ! You get 5x the number of pixels (400x300!) to use as an e-reader or maybe a weather display / calendar. Everything comes fully-assembled, so there's no soldering required! The display is securely plonked down to the Inky wHAT...

The  Snake Eyes Bonnet  is a  Raspberry Pi accessory  for driving  two 128x128 pixel OLED  or  TFT LCD  displays, and also provides four  analog inputs  for sensors. It's perfect for making cosplay masks, props, spooky sculptures for halloween, animatronics, robots...anything where you want to add a pair of animated eyes! This product is just the Pi Bonnet itself, and some headers so you can...

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's  pHAT Stack!  This expansive breakout PCB offers 6 sets of 2x20 pin headers - one for connecting to your Pi and the other 5 for a plethora of HATs, pHATs or bonnets. The combinations are endless... It's perfect for your projects, displaying temperatures, times, etc. and becomes really useful when combined...

What's that, you say? Pimoroni has another new super sweet tri-color e-paper display? Oh feast your eyes! This  Inky pHat   in Yellow/Black/White is a petite 212x104 pixel three-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the...

The Explorer HAT Pro is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer Pro from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features : 4x buffered 5V tolerant inputs Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V...

Pimoroni has taken all the great features of the Picade PCB and crammed them onto this super Picade X HAT . It's the best, easiest way to make a super-sweet arcade system using any Raspberry Pi. Simply pop it onto your Pi,  plug your Pi power supply into the micro-USB connector on the Picade HAT  (it back-powers your Pi through the GPIO, so no need for a separate power supply), wire up your controls to the terminal...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT or pHAT on your Raspberry Pi Model Zero, 3, 2, A+, or B+ (any Pi with a 2x20 connector). The Pimoroni Mini Black HAT Hack3r is ideal for debugging your (p)HAT projects or combining a (p)HAT with other circuits. Features: HAT & pHAT spec landing area with PCB standoffsIncludes 40 pin GPIO ribbon cableAll GPIO pins...

The Explorer pHAT is the perfect prototyping side-kick for your Raspberry Pi. Based on Pimoroni's popular Explorer Hat Pro, this is a smaller cheaper version designed to fit perfectly on a Raspberry Pi Zero! A heap of useful input and output options have been added that will take your projects to the next level. Great for driving motors, using analog sensors, and interfacing with 5V sensors & systems Though...

PaPiRus Zero is an ePaper / eInk screen pHAT designed for the Raspberry Pi Zero. It’s one of the first true low power displays for the Pi Zero mini computer. ePaper / eInk is a display technology that mimics the appearance of ink on normal paper. Unlike conventional displays, ePaper reflects light – just like ordinary paper – and is capable of holding text and images indefinitely, even without electricity. Because of this,...

The Pimoroni Touch pHAT has six capacitive touch buttons, each with a bright white LED, so you can add a touch interface to your Raspberry Pi. While it is shaped and sized to match a Pi Zero, it works great with any Pi with 2x20 connector. You can even use a dry erase pen to write on the pads to label their function. The pHAT features a CAP1166 capacitive touch and LED driver chip that is read over I2C. Each pad has a matching LED that can be...

The Rainbow HAT from Pimoroni has a buffet of sensors, inputs, and displays to explore Android Things™. Use it as a weather station, a clock, a timer or stopwatch, a mood light, or endless other things. Pimoroni collaborated with the Android Things™ team at Google to create this great add-on board that features displays, sensors, sound, and lots of LEDs! It's the perfect introduction to developing Android Things applications on...

Control your Raspberry Pi 3, 2, A+, B+, or Zero with a flick of the wrist! The  Pimoroni Skywriter HAT senses the position of your fingers in the air above. Using Pimoroni's Python API you can read off the positional data (x, y, z) and common gestures like flick left, tap, and double tap. Electrical near-field 3D/gesture sensing4-layer PCB for best sensing performanceSenses from up to 5cm awayFull 3D position data...

The OLED Bonnet Pack for Raspberry Pi Zero  sets you up with the Pi Zero W, and our popular 128x64 OLED Bonnet. It's the big sister to our mini PiOLED add-on. This version has 128x64 pixels (instead of 128x32) and a much larger screen. With the OLED display in the center, we had some space on either side so we added a 5-way joystick and two pushbuttons. The OLED Bonnet is great for when you want to have a control interface for...

The Pan-Tilt HAT  from Pimoroni lets you mount and control a pan-tilt module right on top of your Raspberry Pi. The HAT and its on-board microcontroller let you independently drive the two servos (pan and tilt), as well as driving up to 24 regular LED (with PWM control) or NeoPixel RGB (or RGBW) LEDs. There's also a handy slot through which you can route the servo, LED, and camera cables. The module pans and tilts through 180...

The Joy Bonnet Pack for Raspberry Pi Zero WH  sets you up with the fully assembled Pi Zero WH, and our Joy Bonnet  -  our most fun Bonnet ever! This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you install our script onto your Pi, the controls will act like a keyboard, for easy use with any emulator or media player. This pack is plug-and-play, no...

Playing retro games is easy on a Raspberry Pi - and that pocket-sized computer is pretty good at it too! All you need is a little help to connect buttons and a joystick up and you can custom design your own arcade console, desktop or stand-up machine, even just a simple controller box. It makes for a fun weekend project that will last all year. This Adafruit Arcade Bonnet is designed to make small emulator projects a little easier to build....

Adding a 28 RGB LED pixel strip to your Pi without soldering?! Yes, it's possible! Pimoroni's LED SHIM for Raspberry Pi is fantastic for displaying sensor readings, status updates, measuring voltages, whatever you want to show with a colorful LED light bar. Instead of waiting for your soldering iron to heat up, just slip the SHIM over your Pi pins with the fancy new, friction-fit header! The SHIM is nicely thin at just 0.8mm, so you can...

In the beginning there was Inky pHAT, a triumvirate of eInk bonnets from Pimoroni. And now, Pimoroni has upped their electronic paper displays to  4.2"  glorious inches! Say hellooo to  Inky wHAT ! You get 5x the number of pixels (400x300!) to use as an e-reader or maybe a weather display / calendar. Everything comes fully-assembled, so there's no soldering required! The display is securely...

What if Scroll pHAT had twice times as many pixels and individual pixel brightness control? Scroll pHAT HD , that's what!! Scroll pHAT HD packs 17x7 bright white pixels (119 total) onto a single pHAT, and gives you full PWM brightness control over each pixel. Create beautiful animations and even anti-aliased text by taking advantage of the per-pixel brightness. Use Scroll pHAT HD as a scrolling message display for your tweets, the weather or...

Unicorn HAT HD crams 256 RGB LEDs, in a 16x16 = 256 LED matrix, onto a single HAT. High-definition rainbow goodness! You can still use it for all of the same things as the regular Unicorn HAT, but with four times as many pixels it makes much more complex animations possible, including scrolling text, and even low resolution videos. The bundled ninja diffuser makes the pixels look extra shiny by providing some subtle diffusion, blurring the...

Remember those cereal commercials that would always say, "part of a complete breakfast"? Well the Pi Zero's a lot like that bowl of cereal - while it's great on its own, you need a lot of accessories to make it a complete meal.  The Pi Zero Stereo W Bonnet Pack  sets you up with the WiFi-enabled Pi Zero W, and our I2S 3W Stereo Speaker Bonnet. This bonnet uses digital sound standard...

Here at Adafruit we never tire of cool, new displays, so these super sweet e-paper displays really caught our eye! Pimoroni's Inky pHat is a petite 212x104 pixel two-color display that looks fantastic and is easy to read even in bright daylight. Broadcast your tweets, the weather, or even graphing data. eInk is great for displays that don't change often, due to the 3-second display-change-cycle. But the...

The Joy Bonnet Pack for Raspberry Pi Zero W sets you up with the Pi Zero W, and our Joy Bonnet  -  our most fun Bonnet ever! This Bonnet fits perfectly on top of your Raspberry Pi Zero (any kind) and gives you adorable hand-held arcade controls. Once you install our script onto your Pi, the controls will act like a keyboard, for easy use with any emulator or media player. Note: Due to popular demand, there might be some delay in...

The PaPiRus Screen HAT  from Pi Supply is an ePaper / eInk screen HAT designed for the Raspberry Pi. Think of it as the older sibling of the PaPiRus Zero. ePaper / eInk is a display technology that mimics the appearance of ink on normal paper. Unlike conventional displays, ePaper reflects light – just like ordinary paper – and is capable of holding text and images indefinitely, even without electricity. Because of this, ePaper...

Snap the Pimoroni Unicorn pHAT  on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a fun 4x8 RGB LED matrix powered directly from the Pi. The Unicorn pHAT provides a wash of controllable color that is ideal for mood-lighting, 4x8 pixel art, persistence of vision effects, status indications, or just blasting color into your surroundings. 32 fully controllable RGB LEDs (SK6218 - 3.5mm x...

The Pimoroni Display-O-Tron HAT is an upgraded HAT version of our Display-O-Tron 3000! The Display-O-Tron is a lovely 16x3 character LCD display with capacitive touch pads, GPIO breakout pins, and a six-zone RGB backlight (twice as bright as the older Display-O-Tron 3000)! The capacitive touch pad is ideal for navigating on-screen menus or inputting data and there are some pretty common GPIO pins added for those of...

Pimoroni's GFX HAT is a shiny new LCD Display with RGB Backlight and Touch Buttons! This is a seriously snazzy LCD that can display complex graphics for all your headless Pi games and animations. While the LCD is monochrome 128x64 pixels, the backlight can be set to different RGB colors to indicate You also get six capacitive touch buttons for input and navigation, so you can use this as a controller too. The cool capacitive touch...

Looking for an unashamedly old school LED matrix display board? Lookie here! The Pimoroni Micro Dot pHAT is made up of six red LED matrices, each 5x7 pixels (for an effective display area of 30x7) plus a decimal point, using the beautiful little Lite-On LTP-305 matrices. Perfect for building a retro scrolling message display, a tiny 30-band spectrum analyzer, or a retro clock. Far out! As with the other pHATs, it works with all of the...

Raspberry Pi - meet your new musical B.F.F! With the Pimoroni Piano HAT  you can control hardware synthesizers and software synths or play some really beautiful music in Python. Surprise everyone with your creativity, maybe even yourself! This HAT comes with 16 touch sensitive buttons, up and down octave controls, and 13 piano keys from C to shining C! Each button on Piano HAT can be...

Our pirate friends at Pimoroni have taken the I2S mono DAC and amplifier that they used on Speaker pHAT and Picade HAT and added a second one for stereo goodness. pHAT BEAT gives you high-quality, digital, amplified, stereo audio and 16 beautiful little RGB LEDs, in two rows of 8, that are ideal as a VU meter, and 6 buttons to control your audio. There's a nifty little DIP switch on the bottom of the...

Snap the Pimoroni Unicorn Hat on top of a Raspberry Pi model A+ or a model B+ for a fun 8x8 RGB LED matrix powered directly from the Pi. Unicorn HAT provides a wash of controllable color that is ideal for mood-lighting, 8x8 pixel art, persistence of vision effects, status indications, or just blasting colour into your surroundings. 64 RGB LEDs (WS2812B) each wtih 24-bit RGB colorPython API (NeoPixel compatible!)EEPROM with...

Get visual feedback from your Pi! The PiGlow is a small add on board for the Raspberry Pi that provides 18 individually controllable LEDs. You can use it for all sorts of things! And of course, it fits inside a Pibow! There are tons of things you can do with it: Mood lighting / ambianceShowing current system loadNotify you of events like mentions in tweets or incoming e-mailFeedback the status of scripts/daemons running on your PiWorks great...

The latest Raspberry Pi computers come with WiFi and Bluetooth, and now you can add even more radio options with the Adafruit Radio Bonnets! Upgrade your Raspberry Pi with an RFM69 or LoRa / LoRaWAN radio, so it can communicate over very long distances. These bonnets plug right into your Pi and give you long range wireless capabilities to remote nodes that may be battery powered. Or, you can create Internet gateways with ease. You not only get a...

You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet .  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors  What is particularly nice about this Wing is...

The RaspiRobot Board v3 is an expansion board designed to turn your Raspberry Pi into a motor controller! This board comes fully assembled and includes a switched-mode power supply so you can supply your Raspberry Pi from a variety of battery packs. The v3 fits right on top of your Pi's GPIO socket and allows for bi-directional control of both motors with an L293D H-Bridge motor driver chip. It also allows for control of both motor's...

AHOY , wanna spell out some LOVE with this COOL Raspberry Pi FOUR letter PHAT ? Pimoroni's Four Letter pHAT has four 14-segment displays that you can use to display text, numbers, and a host of other characters. The LEDs are a beautiful retro green, just like your old digital alarm clock. They're driven by the HT16K33 chip over I2C, which does all the multiplexing for you. While it is shaped and sized to match a Pi Zero, it works great...

Let your Pi talk back with this slick little 11x5 LED matrix Scroll pHAT ! The Scroll pHAT provides a matrix of 55 white LED pixels that is ideal for writing messages, showing graphs, and drawing pictures. Use it to output your IP address, show CPU usage, or just play very-low-rez pong! Though designed to match the format of the Raspberry Pi Zero it is compatible with all 40-pin GPIO Raspberry Pi variants (2/B+/A+). Features: 55 white...

So you've got your Pi 3 with its built-in wireless LAN and Bluetooth, but what about your Pi Zero? Say hello to the IoT pHAT from Red Bear! This Zero-size board provides WiFi (802.11bgn / 2.4GHz) and Bluetooth (v4.1 / BTLE) connectivity direct from the GPIO header. You don’t need to use a dongle plugged into the Pi Zero’s solitary data micro-USB port via a USB OTG adapter. Just snap it   on top of a Raspberry Pi...

So you've got your Pi 3 with its built-in wireless LAN and Bluetooth, but what about your Pi Zero? Say hello to the IoT pHAT from Red Bear! This Zero-size board provides WiFi (802.11bgn / 2.4GHz) and Bluetooth (v4.1 / BTLE) connectivity direct from the GPIO header. You don’t need to use a dongle plugged into the Pi Zero’s solitary data micro-USB port via a USB OTG adapter. Just snap it   on top of a Raspberry Pi...

Raspberry Pi and Pimoroni Piano HAT have found a new musical companion! With the Pimoroni Drum HAT  you can play music in Python, control software drum synths on your Pi, take control of hardware drum machines, or just build it into an elaborate drum-controlled project! This HAT comes with 8 finger-sized capacitive touch sensor drum pads. Each pad on Drum HAT can be individually watched in Python and hooked up to...

Unleash the audio capabilities of your Raspberry Pi! The Cirrus Logic Audio Card , produced by Element14 in collaboration with Cirrus Logic, offers Raspberry Pi® users similar flexibility to a PC sound-card to capture audio alongside their camera, and experiment with stereo digital capture and playback. The Cirrus Logic audio board adds a powerful class D amplifier to the Raspberry Pi. The audio board adds inputs for SPDIF, Line in and...

A nifty little breakout from our friends at Pimoroni that lets you access all of the GPIO pins while also running a HAT on your Raspberry Pi Model Pi 3, 2, A+, or B+. The Pimoroni Black HAT Hack3r is ideal for debugging your HAT projects or combining a HAT with other circuits. Features: HAT spec landing area with PCB standoffsIncludes 40 pin GPIO ribbon cableAll GPIO pins labelled with function, BCM pin number, physical pin numberRubber...

The Explorer HAT is a terrific prototyping side-kick for your Raspberry Pi 2, B+, or A+! On the Explorer from Pimoroni there are a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch interfaces! Features: 4x buffered 5V tolerant inputs Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V...

The RTK Raspberry Pi Motor Controller Board Kit is a simple to use, budget-friendly, motor controller board for the Raspberry Pi that allows you to control motors using the GPIO Pins with very little coding. The RTK RPi M.C.B is a self-assembly kit that allows you to control DC motors with ease. Once the board is soldered up it is as simple as plugging the board on top of a Raspberry Pi and then programming Python, Scratch or any other method of...

The HiFiBerry DAC+ is a high-resolution digital-to-analog converter for the Raspberry Pi 2 Model B and the A+ / B+ Models.  This product also works with the Pi 3! This is a special sound card for the Raspberry Pi, that is optimized for one specific use case: the best audio playback quality. This is the Standard RCA version which uses RCA connectors that you know from your normal stereo equipment. The HiFiBerry, like all Pi HATs,...

PiJack  is a HAT (yes, a proper HAT, not a pHAT!) add-on board for the Raspberry Pi Zero mini computer that makes connecting your Pi Zero to the Internet via Ethernet super simple. If you're fed up with flaky WiFi and want your Pi Zero to be online all the time, then this HAT is for you! PiJack is a neat little board with an Ethernet controller and standard RJ45 connector so you can hook your Pi up to your home or office...

Add precise capacitive touch, distance sensing and high quality audio to your Raspberry Pi A+, B+, Zero and later (any Raspberry Pi with a 40 pin GPIO connector) with the Pi Cap from Bare Conductive! Connect Electric Paint or anything conductive to one of the 12 electrodes to control sounds, video and more. Connecting the physical world to the digital world is easy with Bare Conductive's fully featured...

Stack and connect multiple plates and breakout PCB's onto your Raspberry Pi with this custom-made, 2x20 extra tall SMT female header.   This header allows you to plug your Raspberry Pi HAT onto a Raspberry Pi A+, B+ or Pi 2. We also carry various through-hole versions but this is for when you really need to have all the space available, such as on our 3.5" PiTFT