Hunger Games Dress with LED Fire #WearableWednesday

I was nominated for Geek of the Year in Philadelphia, which was the perfect excuse to come up with a geek inspired outfit. I remembered seeing the Hunger Games movie with the flaming wedding dress, and even then I had the idea of creating flames with LEDs. So, I bought a slightly used wedding dress and petticoat from Ebay and got to work.

My idea was to spin in the dress and cause LEDs to turn on. So, for starters I knew I would be using NeoPixel 30 strips in white. I couldn’t afford 9 meters, so I went with 7 — a total of 208 pixels. Using organza ribbon (to save on stitching time), I folded it over and stitched it near the edge to seal it. Then, I stitched both edges of the ribbon onto the bottom of the petticoat in a spiral, creating a casing for over three rows of pixels. Preparing the NeoPixels strips was easy. I removed the weatherproof casing and then soldered the strips together with tiny pieces of Adafruit’s new silicone wire. Can I tell you how much I love this wire? It’s like spaghetti! It’s easy to remove the shielding, and once soldered, it allows your piece to be quite flexible — perfect for a wearable. I slid the NeoPixel strips into the long casing on the petticoat, not only allowing for illumination, but also creating the modern day “hoop” feeling which is perfect for a ball gown.

Gyro

In order for the dress to react to a spin, I learned that I would need a gyrosensor. Adafruit was out of stock for the one that matches the FLORA, so I went with the flat breakout board. I soldered up the wires and attached it to the back of the FLORA with foam adhesive tape. After running a few tests of the gyro, watching numbers fly by on Arduino’s serial monitor, I figured out which scale worked best for the spin. Now that it  was working, it was time to attach it to the large LED strip. Since this was going to be a wearable with lots of movement, I used more of the silicone wire and then hot glued all solder points, to add durability. Then, I uploaded a program I hacked from Paul Craven’s Light Strip Tube Lamp.

Petti

The last part entailed the decorations on the bodice, which really make the dress memorable. I used feather trim and hot glued it into the tucks in the organza. Then it was time to tackle the most difficult part, creating wings that looked lasercut on a budget. I learned about a method using craft foam from a cosplay website. My husband enlarged the actual costume shot from the movie, and helped me to create a pattern. The wings were then cut with an Exacto knife and painted with five coats of glue, two coats of chrome acrylic and two coats of poly. They ended up being somewhat stiff, but I heard that fabric backing would have been the ideal way to go for something firmer. I glued crystals onto the wings, as I believe the original design also had them, and then attached the wings to the bodice with some silver thread. One of the advantages of craft foam, besides being easy to shape with heat, is that it is also safe to wear in crowds.

Bodice

I didn’t win the prize for the biggest geek, but I definitely was the best dressed geek LOL. People who recognized the the dress from the movie were really blown away when they saw the spinning LED show. Probably out of the things I’ve made, this is my favorite; I continue to be inspired by movies and the beauty of diffused lighting. I’m sure a lot of you feel the same way, so get started on your own formal wear with the Sparkle Skirt tutorial. Or, if you want to be more like Katniss, order a gyro breakout board.


Flora breadboard is Every Wednesday is Wearable Wednesday here at Adafruit! We’re bringing you the blinkiest, most fashionable, innovative, and useful wearables from around the web and in our own original projects featuring our wearable Arduino-compatible platform, FLORA. Be sure to post up your wearables projects in the forums or send us a link and you might be featured here on Wearable Wednesday!


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.