Make a battery backup circuit for your Pi! #piday #raspberrypi @raspberry_pi

NewImage

Repair Hub has a useful post on how to build a battery backup circuit for your pi.

This is a step by step instructions on how to make a battery backup circuit for your Raspberry Pi computer. For more information about Raspberry Pi visit the Foundation’s website.

First I’d like to explain a little bit about what I tried to achieve with this design and also pros and cons of this approach. I’m using my Raspberry Pi as a backup device with two hard drives connected to it, to back up various online servers that I administer. I use automated backup scripts based on Rsnapshot, and also I’m using this particular Pi as an Apple time machine server. Because Raspberry Pi is a very low power device, I thought it would be possible to design a cheap backup power supply using a 9V rechargeable battery, and this way prevent any abrupt shutdowns during power cuts or when someone accidentally unplugs it from the mains. As an added feature it also will provide a convenient way to safely power the device off without adding a hardware button or logging-in remotely and issuing a shutdown. But what this circuit doesn’t currently do is monitor battery levels, nor provide any king of low voltage cut off, but there is a time limit/delay after which it will automatically power off and disconnect the battery.

Precautions: Triple check all connections to and from Raspberry Pi before connecting either power supply or battery as I have made a mistake and applied 9V to the GPIO pins which destroyed it instantly. Even better is to use a buffer board of some kind, there are plenty sold online. Also double check that the power supply delivers expected voltage before connecting it to the circuit, and don’t use bad quality power supplies. DO NOT work with mains voltage unless you are qualified.

The finished circuit does the following:

  • Trickle charge the battery while on mains power
  • Send a signal to Pi GPIO pin when mains power is disconnected
  • issue a shutdown after a few minutes if power haven’t returned (Done via software)
  • disconnect the battery from the circuit after shutdown is completed (this is to prevent discharging the battery below its limit)
  • keep a log file with all the time stamps and alerts for mains power, shutdowns and restarts of the Pi

Read more.


Featured Adafruit Product!

NewImage

UBEC DC/DC Step-Down (Buck) Converter – 5V @ 3A output: Your power supply problems just got SOLVED! This little circuit board may look tiny but inside is a high efficiency DC/DC step-down converter which can output up to 3 Amp at 5V without the need of any heat-sink or forced cooling. (It does get a bit toasty at 3A though) UBEC stands for “universal battery eliminator circuit” and this UBEC is designed to replace a 5V supply in RC planes and ‘copters but its also great for any kind of microcontroller or electronics project that runs off of 5V. We tried a half dozen different ‘BECs and found this one to be the best in terms of range and stability. You can check the technical tab for the analysis of input/output range and current draw. Read more.



Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.