dweet.io paired with Arduino gives table game a live scoreboard #arduino #CC3000

Pasted Image 3 2 14 11 30 PM 6

dweet.io paired with Arduino gives table game a live scoreboard. Features the Adafruit CC3000 WiFi Shield. Thanks to Thomas for the tip!

We used dweet.io to connect a foosball table to the Internet during an IoT workshop at Hyperwerk Basel. The main advantage of the service is that it also works without authentication, that it’s trivial to use for everyone who can send a simple Web request, that it’s based on the open JSON standard and that it adds timestamps to entries. As we used Arduinos with either an Ethernet shield or CC3000 WiFi modules, SSL encryption was not an option for us. When we found that dweet.io enforces SSL through redirects and contacted support, the nice folks at Bug Labs immediately adapted their service to enable our use case.

Here’s how it works: Each goal bay is equipped with an Internet-connected Arduino, a PIR sensor to detect goals, and a button to “undo” goals that do not count under the local foosball rules. On startup or reset, the goal counter is set to 0. If a goal is detected, the counter is incremented….

Read More.

Pasted Image 3 2 14 11 30 PM 2


Featured Adafruit Product!

Pasted Image 3 2 14 11 42 PM

Adafruit CC3000 WiFi Shield with Onboard Ceramic Antenna: The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for communication (not UART!) so you can push data as fast as you want or as slow as you want. It has a proper interrupt system with IRQ pin so you can have asynchronous connections. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP & AES. A built in TCP/IP stack with a “BSD socket” interface. TCP and UDP in both client and server mode, up to 4 concurrent sockets. It does not support “AP” mode, it can connect to an access point but it cannot be an access point. We carefully wrapped this little silver module into an Arduino shield. We also added a microSD socket and a reset button. It has an onboard 3.3V regulator that can handle the 350mA peak current, and a level shifter to allow 3 or 5V logic level. The antenna layout is identical to TI’s suggested layout and we’re using the same components, trace arrangement, and antenna so the board maintains its FCC emitter compliance (you’ll still need to perform FCC validation for a finished product, but the WiFi part is taken care of). Even though it’s got an onboard antenna we were pretty surprised at the range, as good as a smartphone’s. (read more)


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.