#hackfriday Gardening — Planting Garlic

Conventional wisdom would say that late November is too late in the year to put garlic in the ground, but I’ve been planting garlic on the day after Thanksgiving for the past few years. Each time I’ve been rewarded with a great harvest in the late spring, so maybe conventional wisdom is wrong.

The first thing to do is to break up the garlic into individual cloves (as in the photo above). You’ll notice that these cloves have green sprouts. While it’s not critical to have these sprouts (in my experience, some varieties of garlic don’t develop sprouts until they’re in the ground), they can be helpful to the plant in getting nutrients from the soil immediately after planting. While you can’t make the garlic sprout green on short notice, you can help it to acclimate more quickly by soaking it in a mixture of water and baking soda (1 qt water + 1 tbsp soda) for a couple of hours.

The next step is a clear a bit of land in your garden. Garlic is, for the most part, a hardy plant that will take care of itself. However, because it is a bulb, it requires well-drained soil to prevent rotting. An 8-12″ raised bed of topsoil works quite well. Clear any weeds out of your little plot and till the soil a bit to aerate it.

Next, you’ll want to dig some holes. Garlic should be planted 6-10″ apart. Use a shovel handle or large dowel to make the holes.

Lay out your cloves of garlic and then drop them in! The green sprouts (if any) should point upwards and the flat root section should point down.

Rake over the whole bed to fill in the holes and aerate the soil some more. If the soil is particularly dry, water the ground a little bit. If you expect a cold winter, cover the ground with straw or gardening paper. In the case of paper, you should remove it in early March when the weather gets warmer.

And that’s it!

Depending on the local climate, and the weather for the next 6-7 months, your garlic should be ready to pick by mid-June!

Happy hacking!

(more about #hackfriday)


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.