Bit Banger: An ATTiny Video Demo

Linus (lft) writes:

Bit banger is built around an ATtiny15 microcontroller, which runs at 1.6 MHz and has 1 kB of flash ROM and a claustrophobic 32 bytes of RAM. In fact, those 32 bytes are the CPU registers. Only the most basic AVR instructions are supported; they occupy at least two bytes each, and can obviously not be compressed since they are executing from ROM, so a maximum of 512 instructions will fit inside the chip (fewer if static data is needed).

The microcontroller supports interrupts, but they would have been too costly to use. Instead, the entire demo is cycle counted.

At a clock rate of 1.6 MHz, the visible part of each line of the VGA signal swooshes by in exactly 36 clock cycles. The entire line, including horizontal blanking, is 51 clock cycles wide. During this time, both graphics and sound must be generated.

I quickly arrived at the following overall design: Three registers make up a 24-bit frame buffer, organized as a 3×8 grid. Every 60 raster lines, these registers are rotated one bit, to prepare for the next row of the grid. At three different positions along the visible part of the line, the MSB of the corresponding frame buffer register is interpreted as an instruction to either keep or invert the current colour; the resulting colour is then transmitted onto an output pin. At the end of the visible line, black is selected.

In the gaps between these four positions and the two places where the horizontal sync signal is flipped, sound must be generated and emitted. The ATtiny15 luckily has a PWM output that runs on a separate peripheral clock at a staggering 25.6 MHz, which is high enough for 8-bit audio output. Writing a sample to the PWM output is a simple one-cycle instruction; the challenge is to calculate the value of the sample during the remaining clock cycles.

hardcore+BA, and the song is a straight-up jam. Happy Friday!


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



3 Comments

  1. pretty exciting for a $2 part 😀

  2. KIKKIN’ RAD! That was an excellent demo!

  3. It’s really cool that he is generated both the audio and video from such a tiny microcontroller! The demo scene is always impressive in that regard.

Sorry, the comment form is closed at this time.