5.6" Display & Audio 1280x800 (720p) Kit - HDMI/VGA/NTSC/PAL

PRODUCT ID: 1695
$149.95
Also include 1 x 9 VDC 1000mA regulated switching power adapter - UL listed ($6.95)

QTY DISCOUNT
1-9$149.95
10-99$134.96
100+$119.96
6 IN STOCK
  • Description

    Description-

    Make a lovely audio/video setup with a 5.6" 720p screen with HDMI stereo speaker support. For video, we have a super-sharp 5.6" TFT display with incredibly high resolution - it has 270 PPI! We tried to get the smallest & highest resolution display that would be good for embedded computing usage. The visible display measures 5.6" diagonal and is a 'raw' LVDS display as is used in a tablet, ultra thin with some mounting tabs around the edge. We include a driver board with HDMI, VGA and Composite inputs as well as stereo 4 ohm at 3W output driving capability. The setup is very easy to use - simply connect a 5-12VDC adapter to the 2.1mm center-positive DC jack, then connect a digital video source to one of the ports and two 4 to 8 ohm speakers to the SPK output pins. Voila, a display!

    It is not an IPS display so its best for direct viewing, our 7" and 10" HDMI displays are IPS so they look great from any angle.

    There's a little wired PCB with little buttons that let you enter a menu system for adjusting brightness, color and contrast. It tries to auto-detect which input you have and switches to that one or you can 'select' from the menu keypad which to display.

    We include a plug-in cable that connects to the 4 speaker output pins, the pins are labeled LOUT+/- and ROUT+/- you'll have to solder your own speakers to the 4 wires

    To demonstrate it, we took some photos with the display connected to a Raspberry Pi, but it will also work connected to any device with HDMI, VGA or NTSC/PAL output. It will not work with a device that only outputs DVI (without a DVI->HDMI converter) or SECAM.

    For use with a BeagleBone black, we found it works when plugged in, no configuration required.

    A power adapter is not included! Any 5 to 12VDC adapter will work nicely: we prefer 9V DC. Check the technical tabs for current draw at various voltages. We show the display on a bent wire stand which is not included, but you can pick one up here

    5.6" Display & Audio 1280x800 (720p) Kit - HDMI/VGA/NTSC/PAL (15:20)

  • Technical Details

    Technical Details+

    • Driver Datasheet
    • Keyboard Datasheet
    • Power with 5-24VDC
    • 16:10 display ratio
    • Resolution: 1200 x 800
    • Visible area: 121mm x 76mm 16:10
    • Brightness: 300cd/m2
    • Contrast: 400:1
    • We ship with an LTD056EV7F display, or equivalent, however we don't have a datasheet for this exact display
    • Display dimensions: 140mm x 89mm x 3mm
    • Not HDCP compatible - it cannot be used with 'secured' HDMI sources

    Power draw from combined display+HDMI driver when backlight is on

    • 5V: 650mA
    • 6V: 550mA
    • 7V: 450mA
    • 8V: 400mA
    • 9V: 350mA
    • 10V: 325mA
    • 11V: 300mA
    • 12V: 275mA

    Driver details:

    • Board Dimensions: 90mm x 66mm (3.5" x 2.6")
    • Weight: 60g

    This is our recommended config.txt for Raspberry Pi

    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1
    
    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    #disable_overscan=1
    
    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=-40
    #overscan_right=-40
    #overscan_top=-40
    #overscan_bottom=-40
    
    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=800
    
    # uncomment if hdmi display is not detected and composite is being output
    hdmi_force_hotplug=1
    
    # uncomment to force a specific HDMI mode Group 2 and Mode 28 is 1280x800 @ 60hz
    hdmi_group=2
    hdmi_mode=28
    
    # This line will force the Pi to recognize the HDMI driver in video and audio mode
    # change to =1 to have video only
    hdmi_drive=2
    
    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    #config_hdmi_boost=4
    
    # uncomment for composite PAL
    #sdtv_mode=2
    
    #uncomment to overclock the arm. 700 MHz is the default.
    #arm_freq=800
    
    # for more options see http://elinux.org/RPi_config.txt
    
  • Learn

    Learn+

    Build wearable DIY VR Goggles!
    Learn about our wide variety of HDMI/VGA/Composite Displays!

MAY WE ALSO SUGGEST...

MAY WE ALSO SUGGEST...-