Raspberry Pi emulator console for the backseat #piday #raspberrypi @Raspberry_Pi

NewImage

Great project from MoTiknkerGNome on Instructables.

Scope of project: After building a Bar-Top Raspberry Pi retro gaming machine I determined that while cool I cant take it around easily as it weighs about 40 lbs and is the size of a large microwave. And while fun for the basement perhaps Arthur would want to play it in the car for the long drives back to his Moms house.

My original plan for this build was based off the Adafruit PiGRRL but I I wanted the ability to play the SNES and Genesis emulators. I figured I would just need to add a couple more buttons and it would be a peace of cake. I thought wrong.

Unlike my other projects I bought almost everything for this build. I used my 10% off coupon for being a pro member with Adafruit, I have to say their support forums are great and the benefit of being an Instructables Pro member was worth it just with the savings on that one order. I chose the the 5″ non touch TFT with HDMI input however in hindsight with the finished project I would have picked a analog/composite display as the driver board and signal wires are easier to route then HDMI.

I wanted to build a Gameboy and wound up with a cyberpunk looking headrest console. But the build was fun and the end result works. I am sure Arthur is going to like playing games instead of sitting for 3 hours in the car. Ill include pictures from the failed project just to show that sometimes things don’t go perfectly and that is OK.

Take a break put it aside then when you come back you may have the fresh perspective to figure out the problem that was driving you insane in the first place.

Oh and I am sure I am going to drive someone nuts as I will switch between Metric and Imperial measurements with equal aplomb. Some things are only mentioned in MM and others are only referenced in inches. I will try to keep it all in millimeters for accuracy but somethings are only sold with inch measurements here in the states.

Shall we get to building? This took me about 3 weeks of tinkering after I scrapped the first 2 handhelds, I started pretty much as soon as I finished the bartop.

*Further note* The finished console is a full raspberry pi computer. With the wireless keyboard and mouse, and the little 802.11n wireless chip. I can exit emulation station using the controller or keyboard then boot to a shell or X to join wireless networks get on the internet or code. As everything is sealed in carbon fiber and plastic the wifi is needed to load ROM’s and updates.

See the full tutorial here.

NewImage


Featured Adafruit Product!

NewImage

HDMI 4 Pi: 5″ Display (no Touch) w/Mini Driver – 800×480 HDMI: Yes, this is a cute little 5″ TFT display with WVGA 800×480 resolution and a cute little driver board. We tried to get the smallest display that would be good for embedded computing usage and at a good price. And we also tried to match it with a small driver board that can be powered from a USB port. The visible display measures 5″ diagonal and is a ‘raw’ TTL display as is used in portable electronics. The driver board only has an HDMI input but for Raspberry Pi, BeagleBone Black and other computers, HDMI is the best quality output available. The display is very easy to use – simply connect the USB power cable to 5V power supply that can provide 500mA, then connect a digital video source to one of the HDMI port. Voila, a display! Read more.


998Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!


Adafruit publishes a wide range of writing and video content, including interviews and reporting on the maker market and the wider technology world. Our standards page is intended as a guide to best practices that Adafruit uses, as well as an outline of the ethical standards Adafruit aspires to. While Adafruit is not an independent journalistic institution, Adafruit strives to be a fair, informative, and positive voice within the community – check it out here: adafruit.com/editorialstandards

Join Adafruit on Mastodon

Adafruit is on Mastodon, join in! adafruit.com/mastodon

Stop breadboarding and soldering – start making immediately! Adafruit’s Circuit Playground is jam-packed with LEDs, sensors, buttons, alligator clip pads and more. Build projects with Circuit Playground in a few minutes with the drag-and-drop MakeCode programming site, learn computer science using the CS Discoveries class on code.org, jump into CircuitPython to learn Python and hardware together, TinyGO, or even use the Arduino IDE. Circuit Playground Express is the newest and best Circuit Playground board, with support for CircuitPython, MakeCode, and Arduino. It has a powerful processor, 10 NeoPixels, mini speaker, InfraRed receive and transmit, two buttons, a switch, 14 alligator clip pads, and lots of sensors: capacitive touch, IR proximity, temperature, light, motion and sound. A whole wide world of electronics and coding is waiting for you, and it fits in the palm of your hand.

Have an amazing project to share? The Electronics Show and Tell is every Wednesday at 7pm ET! To join, head over to YouTube and check out the show’s live chat – we’ll post the link there.

Join us every Wednesday night at 8pm ET for Ask an Engineer!

Join over 36,000+ makers on Adafruit’s Discord channels and be part of the community! http://adafru.it/discord

CircuitPython – The easiest way to program microcontrollers – CircuitPython.org


Maker Business — “Packaging” chips in the US

Wearables — Enclosures help fight body humidity in costumes

Electronics — Transformers: More than meets the eye!

Python for Microcontrollers — Python on Microcontrollers Newsletter: Silicon Labs introduces CircuitPython support, and more! #CircuitPython #Python #micropython @ThePSF @Raspberry_Pi

Adafruit IoT Monthly — Guardian Robot, Weather-wise Umbrella Stand, and more!

Microsoft MakeCode — MakeCode Thank You!

EYE on NPI — Maxim’s Himalaya uSLIC Step-Down Power Module #EyeOnNPI @maximintegrated @digikey

New Products – Adafruit Industries – Makers, hackers, artists, designers and engineers! — #NewProds 7/19/23 Feat. Adafruit Matrix Portal S3 CircuitPython Powered Internet Display!

Get the only spam-free daily newsletter about wearables, running a "maker business", electronic tips and more! Subscribe at AdafruitDaily.com !



No Comments

No comments yet.

Sorry, the comment form is closed at this time.